pt. tolan tiga indonesia · 1.1.1 kelebihan okulasi hijau penggunaan bahan tanam yang diokulasi...
Post on 15-Jan-2020
24 Views
Preview:
TRANSCRIPT
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 1 of 33
1. NURSERY
Pembibitan
1.1. Green Budding Nursery
1.1.1 The advantages of green budding
Planting material strictly prepared by
grafting the young seedling in the polybag
(green budding) is of an alternative of
rubber planting material to be planted in
the field. The advantages to utilize the
green budding seedling compare to
budded stump are as follow:
1. The nursery works are not depend
on climate condition
2. Maintenance and production costs
are cheaper
3. A reduction period of two whorl
seedling production
4. A reduction of immature period; 4-6
months shorter
5. Tolerant of drought condition during
field planting
6. Minimum space requirement for
nursery area
7. Very uniform vigorous growth of
seedlings is possible
8. Fewer seeds are required
1.1. Pembibitan Okulasi Hijau
1.1.1 Kelebihan okulasi hijau
Penggunaan bahan tanam yang diokulasi
langsung polibag (green budding)
merupakan alternatif pengadaan bahan
tanam karet. Keunggulan bibit hasil
okulasi green budding dibandingkan
dengan bibit hasil okulasi konvensional
adalah sebagai berikut :
1. Pembibitan tidak selalu tergantung
kepada iklim
2. Biaya produksi dan pemeliharaan
bibit lebih rendah
3. Waktu untuk menghasilkan bibit
berpayung dua menjadi singkat;
4. Waktu matang sadap adalah 4-6
bulan lebih cepat.
5. Bibit green budding lebih tahan
pada kondisi kering di lapangan.
6. Lahan untuk pembibitan tidak perlu
luas
7. Memungkinkan bagi pertumbuhan
bibit yang jagur dan seragam
8. Kebutuhan biji lebih sedikit
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 2 of 33
To support the success of green budding
nursery, there are some requirements to be
fulfilled as follows :
1. Good water availability during nursery
period
2. The budwood multiplying gardens
should be close to nursery site.
3. Skill budding operator should be
available in a reasonable numbers.
4. Discipline in nursery practices
1.1.2 Phasing of operations
(i) Timing of operations for the
production of green budding will
depend much on local circumstances
such as seed availability, optimum
planting, weather, etc.
(ii) The aim is to have available well
developed planting material ready
for planting at the initial of reliable
rainy season.
(iii) The Figure 1.1 showing a specimen
of a work programme showing
various nursery tasks prior to field
planting.
Untuk mendukung keberhasilan
pembibitan green budding, diperlukan
juga beberapa syarat penting:
1. Ketersediaan air yang cukup
sepanjang masa pembibitan.
2. Lokasi kebun entres diharuskan
dekat dengan lokasi pembibitan.
3. Juru okulasi yang terampil untuk
menjamin keberhasilan okulasi
4. Disiplin dalam pelaksanaannya.
1.1.2 Tahap-tahap pelaksanaan
(i) Pelaksanaan penanaman okulasi
hijau, bergantung pada keadaan
sekitarnya seperti ketersediaan
biji, penanaman yang optimum,
musim tanam yang sesuai dll.
(ii) Tujuan utamanya adalah
mempersiapkan bahan tanaman
yang telah tumbuh sempurna pada
awal musim hujan.
(iii) Jadwal pada gambar 1.1 di bawah
ini menunjukkan tahap-tahap
rencana kerja sebelum menanam
ke lapangan.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 3 of 33
1.1.3 Selection of nursery site
1.1.3.1 Location of nursery
(i) The nursery is best sited on level,
fertile and well drained loam soil as
this simplifies preplanting
cultivation giving a good tilth and
suitable soil conditions for healthy
growth
(ii) In areas of low rainfall, sources of
water close to the nursery are
important. Where rainfall is high, the
water table should be below 90 cm.
In low rainfall sites, a water table
up to 60cm is acceptable. All
locations require sufficient drains to
reduce flood in high rainfall periods.
(iii) Nurserie sould be reasonably
sheltered but not over shadowed by
nearby vegetation. Mature rubber
should be at least 15 m away from
the nursery on all sides.
(iv) Whilst the nursery should be as near
the field planting site as possible to
keep transport costs low, the prime
1.1.3 Penentuan lokasi pembibitan
1.1.3.1 Lokasi nursery
(i) Bibitan sebaiknya berada di tanah
datar, subur dan berdrainase baik,
ini mempermudah perawatan pada
pre-planting sehingga tersedia
lahan dan tanah sesuai untuk
pertumbuhan yang sehat.
(ii) Di daerah bercurah hujan rendah
sumber air harus dekat
pembibitan. Bila curah hujan
tinggi air tanah harus lebih rendah
dari 90 cm. Di real rendah curah
hujan air tanah ditoleransi sampai
60 cm. Semua lokasi
membutuhkan jumlah parit cukup
untuk mengurangi masalah banjir
pada curah hujan tinggi.
(iii) Bibitan harus dinaungi secukupnya
tetapi tidak terlindungi oleh
tanaman sekelilingnya. Tanaman
karet tua sekurang-kurangnya harus
15 m dari bibitan dari semua sisi.
(iv) Disamping bibitan harus sedekat
mungkin dengan lokasi penanaman,
untuk merendahkan biaya transport,
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 4 of 33
NO. NO. NO. NO. ESTIMATEDESTIMATEDESTIMATEDESTIMATED
ITEMITEMITEMITEM REALIZATIONREALIZATIONREALIZATIONREALIZATION SEP OCT NOV DEC JAN FEB MAR APR MAY JUN JUL AUG SEP OCT
1 NURSERY PREPARATIONNURSERY PREPARATIONNURSERY PREPARATIONNURSERY PREPARATION E S T IM A T E D
Persiapan PembibitanPersiapan PembibitanPersiapan PembibitanPersiapan Pembibitan R E A L IZ A T IO N
2 COLLECTING SEEDCOLLECTING SEEDCOLLECTING SEEDCOLLECTING SEED E S T IM A T E D
Peengumpulan Bij iPeengumpulan Bij iPeengumpulan Bij iPeengumpulan Bij i R E A L IZ A T IO N
3 PLANTING SEEDPLANTING SEEDPLANTING SEEDPLANTING SEED E S T IM A T E D
Penanaman Bij iPenanaman Bij iPenanaman Bij iPenanaman Bij i R E A L IZ A T IO N
4 PLANTING GERMINATEDPLANTING GERMINATEDPLANTING GERMINATEDPLANTING GERMINATED E S T IM A T E D
SEED TO POLYBAGSEED TO POLYBAGSEED TO POLYBAGSEED TO POLYBAG R E A L IZ A T IO N
Penanaman Kecambah kePenanaman Kecambah kePenanaman Kecambah kePenanaman Kecambah ke
PolibagPolibagPolibagPolibag
5 POLYBAG NURSERY POLYBAG NURSERY POLYBAG NURSERY POLYBAG NURSERY E S T IM A T E D
MANURINGMANURINGMANURINGMANURING R E A L IZ A T IO N
Pemupukan di pol ibagPemupukan di pol ibagPemupukan di pol ibagPemupukan di pol ibag
6 BUDDINGBUDDINGBUDDINGBUDDING E S T IM A T E D
OkulasiOkulasiOkulasiOkulasi R E A L IZ A T IO N
7 CUTTING BACKCUTTING BACKCUTTING BACKCUTTING BACK E S T IM A T E D
Cutting BackCutting BackCutting BackCutting Back R E A L IZ A T IO N
8 SELECTIONSELECTIONSELECTIONSELECTION E S T IM A T E D
SeleksiSeleksiSeleksiSeleksi R E A L IZ A T IO N
9 WEEDINGWEEDINGWEEDINGWEEDING E S T IM A T E D
Pengendal ian GulmaPengendal ian GulmaPengendal ian GulmaPengendal ian Gulma R E A L IZ A T IO N
10 READY FOR FIELD READY FOR FIELD READY FOR FIELD READY FOR FIELD E S T IM A T E D
PLANTINGPLANTINGPLANTINGPLANTING
Tanaman Siap TanamTanaman Siap TanamTanaman Siap TanamTanaman Siap Tanam R E A L IZ A T IO N
WORK ITEMWORK ITEMWORK ITEMWORK ITEMPREVIOUS YEAR MONTH
Figure 1.1 Specimen of a rubber nursery work programme
consideration must be the best site
possible producing first quality
plant.
(v) The same site can be used in the
next year, but not in third year.
lokasi tersebut harus dapat
menghasilkan tanaman berkualitas
terbaik.
(v) Lokasi yang sama dapat digunakan
pada tahun berikutnya, tetapi tidak
boleh digunakan pada tahun ketiga.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 5 of 33
1.1.3.2 Site preparation
(i) The main point in site preparation is to
produce a good weed free tilth. It is
recommended that preparations start
at least two months before the
scheduled planting of germinated seed.
(ii) The nursery should be leveled and flat
with drains. Construct drains where
necessary ensuring that the nursery
will not be flooded.
(iii) If there is a risk of damage by
animals or humans, the area should be
well fenced with barbed wires.
1.1.3.2 Persiapan lokasi
(i) Yang paling penting dalam persiapan
lahan adalah mempersiapkan lahan
bebas gulma. Dianjurkan agar dimulai
minimal dua bulan sebelum
merencanakan penanaman kecambah.
(ii) Tanah lokasi pembibitan harus datar
dan rata dan mempunyai parit
drainase. Buat parit drainase di mana
perlu agar areal tidak tergenang air.
(iii) Jika ada resiko kerusakan akibat
binatang atau manusia, areal harus
dipagar kawat duri.
1.1.4 Seeds
1.1.4.1 Seed requirement
The number of germinated seeds to be
planted for future budding are 4000 seeds
per ha. This allows for a high level of
selection at each stage, i.e. seed, rootstock,
2-whorl stump.
Seed requirement per hectare :
- Seed 4500
- Planted in polybag 2700
(3 seeds /polybag; 70% germination)
1.1.4 Biji
1.1.4.1 Kebutuhan biji
Jumlah kecambah ditanam untuk okulasi
adalah 4000 biji per ha. Ini
memungkinkan seleksi yang ketat pada
setiap tahapan kerja, yaitu biji, batang
bawah, dan bibit payung dua. Kebutuhan
biji per hektar adalah :
- Biji 4500
- Ditanam di polybag 2700
(3 biji / polybag; 70% daya tumbuh)
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 6 of 33
- Retain only 1 rootstock per bag
- Budding 900
- Polybags success 750
- Field planting 550
(+15% APM for supplying)
1.1.4.2 Seed collection
(i) Seed should be collected early in the
seed season as quality deteriorates
rapidly the longer the seeds remains on
the ground.
(ii) If it becomes apparent that insufficient
seed will be occur before planting,
immediate steps must be taken to
obtain the balance elsewhere
(iii) Seeds should be collected from
clone GT-1, AV 2037, RRIC, PB 260
which are more than 15 years old trees.
(iv) Seed Characteristics of PB 260
The PB 260 seed is biger in size with
thiny shell and light, generally the
amount of the seeds per kilogram are
of 300 seeds. The PB 260 seeds are not
durable for long. Storing the seeds for
more than 10 days from time of
collection may cause the seeds
- Sisakan hanya 1 pohon per polybag
- Okulasi 900
- Polybag (sudah berhasil) 750
- Tanam ke lapangan 550
(+15% APM untuk sisipan)
1.1.4.2 Pengumpulan biji
(i) Biji dikumpulkan pada awal musim
karena kualitas biji menurun
dengan cepat jika biji semakin
lama ditanah.
(ii) Jika kebutuhan biji tidak mencukupi
sebelumtanam harus diambil
langkah cepat untuk memenuhi
kekurangan biji dari tempat lainnya
(iii) Biji harus dikumpulkan dari klon
GT 1, AV 2037, RRIC, PB 260,
pohon yang berumur >15 tahun.
(iv) Karakteristik Biji PB 260
Biji PB 260 ukurannya lebih besar,
cangkang lebih tipis dan lebih
ringan, jumlah biji per kilogram +
300 biji. Biji PB 260 tidak tahan
disimpan lama. Jika disimpan > 10
hari setelah pengambilan dari
lapangan dalam keadaan segar daya
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 7 of 33
viability to decrease. In the case, the
PB 260 seeds should be collected from
the field and should be germinated
without delay.
To prevent low seeds viability the following
items below should be taken into account :
• The seed collection in the field should
be carried out all at once in order to get
fresh rubber seeds in great numbers.
• The seeds should be delivered from the
field as soon as possible.
• The seeds should be immediately
germinated in germination box.
(v) Seed Characteristics of GT1
The GT1 seeds are smaller in size with
thicker and compact shell, generally
the amount are of of 300 seeds per
kilogram. Therefore, the seeds have
better durability. The seeds durability
can persist in 14 days of storaging with
viability more than 70%.
1.1.4.3 Seed Selection
(i) Weight of seed is an important factor,
but not the size. Heavier seeds
germinate more rapidly than lighter
kecambahnya menurun. Jika biji PB
260 digunakan untuk batang bawah
maka dikutip secepatnya dari
lapangan dan segera ditanam.
Untuk menghindari daya kecambah yang
rendah perlu diperhatikan:
• pengumpulan di lapangan harus
dalam waktu bersamaan untuk
mendapatkan jumlah yang besar.
• Pengiriman secepatnya dilakukan,
tidak boleh ditunda.
• secepatnya ditanam ke kotak
pengecambahan..
(v) Karakterisktik Biji GT1
Biji GT1 ukurannya lebih kecil
dengan cangkang lebih tebal dan
lebih padat, umumnya jumlah biji
per kilogram + 300 biji. Dengan
demikian daya tahannya lebih baik.
Biji dapat bertahan selama 14 hari
dengan daya kecambah > 70%
1.1.4.3 Seleksi biji
(i) Berat biji merupakan faktor penting.
Tetapi bukan ukurannya. Biji yang
lebih berat berkecambah lebih cepat
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 8 of 33
ones.
(ii) The shells of good seed are shiny and
bouncy. See Figure below for selecting
good seeds.
1.1.4.4 Seed germination
(i) Germination beds must be situated on
level ground and blocked off with
bricks or timber to form beds of
conveniently reached from two sides
(100 cm wide). Beds are best made
from river sand on top of soil sufficient
to raise the bed about 10 cm above the
ground level. This prevents water
logging in wet weather.
(ii) To prevent drying out and sun scorch
fairly dense shade (80%) must be
provided, about 1 m high of front side
and 75 cm high of back side, above the
bed. As seed lose about 50% of their
moisture within three days, only the
freshest seed should be used and
planted in the bed as soon as possible.
dari biji yang ringan
(ii) Biji yang baik, kulitnya mengkilat dan
melenting. Lihat gambar bagaimana
menyeleksi biji yang baik.
1.1.4.4 Pengecambahan biji
(i) Bedeng kecambah dibuat di tanah
datar dan dibatasi oleh batubata atau
papan untuk membentuk bedengan
yang dapat dijangkau dari dua sisi
(lebar 100 cm). Bedengan paling
baik terbuat dari pasir sungai yang
diisikan sedalam 10 cm dengan
permukaan rata. Ini akan mencegah
penggenangan dimusim hujan.
(ii) Untuk mencegah kekeringan dan
terbakar matahari harus disediakan
naungan (80%) dengan tinggi
bedengan 100 cm dibagian depan
dan 75 cm dibagian belakang. Biji
kehilangan 50% kelembabannya
dalam 3 hari, gunakan biji paling
segar dan tanam sesegera mungkin.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 9 of 33
The more cost-effective procedure is
recommended :
(i) It is not necessary to place each seed
with it dorsal side uppermost. Simply
spread the seed loosely over the sand
bed. The geotropic radicles will grow
downwards without twisting.
(ii) Cover the seed with sand or light
loamy sand and lay gunny sacks or
lalang sheet directly over the seedbed
and keep them moist and shaded.
(iii) When germination starts after 7-9 days
lift off the gunny sacks or lalang sheet
one by one and pluck out the the
germination seeds carefully each day,
then replace the gunny sack until one
or two days later. It is suggested to
withdrawal the ungerminated seeds
over 14 days of germination.
(iv) Harvest the seedlings as soon as the
radicle emerges and turn downwards.
The “star” phase is best because very
few rootlets are damaged and there is
minimal disturbance to other seeds not
yet ready to sprout.
Prosedur yang lebih efektif dan murah
direkomendasi sebagai berikut :
(i) Tidak perlu meletakkan punggung
setiap biji menghadap ke atas.
Langsung serakkan biji diatas
bedengan. Bakal akar geotropic akan
tumbuh ke medium tanpa terpelintir.
(ii) Tutupi biji dengan pasir atau pasir
agak berlempung dan letakkan goni
rami atau lalang menutupi bedengan
sambil dijaga agar tetap lembab dan
ternaungi.
(iii) Saat biji mulai berkecambah setelah
7-9 hari angkat goni atau lalang dari
bedengan satu persatu, dan dengan
hati-hati cabut biji yang
berkecambah, lalu tutup kembali
goni sampai dua hari berikutnya.
Dianjurkan untuk membuang biji
yang tidak berkecambah setelah 14
hari.
(iv) Panen kecambah secepatnya begitu
akarnya berkecambah menghadap ke
bawah. Phase “bintang” adalah saat
yang paling baik karena kerusakan
akar dan gangguan terhadap biji lain
yang belum berkecambah sangat
sedikit.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 10 of 33
(v) When seedlings are planted in the
polybag, the radicle must point
downwards. The orientation of the
seed case is not factor.
1.1.5 Polybag nursery for rootstock
(i) The rootstocks for green budding are
grown in the polybag. The
recommended size of black lay flat
bags is 50cm x 25cm x 0,15mm with
around 30 perforations in the lower 30
cm of the bag.
(ii) Polybags should be filled to within 2
cm of the top of the bag with the best
top soil of good structure. If soil is
heavy, mix in some coarse river sand.
(iii) After soil filling, mix the soil surface
in the polybag with 10 g TSP and 10 g
NPK 15.15.6.4 per polybag
respectively as basic fertilizer.
(iv) Prior to polybags arrangement,
polybag line should be covered with
translucent plastic of 0.04 mm
thickness to prevents the roots
penetrates into soil.
(v) Pada saat kecambah ditanam ke
polybag, bakal akar harus
menghadap ke bawah. Arah
peletakan biji bukan merupakan
faktor penting.
1.1.5 Pembibitan polibag batang bawah
(i) Batang bawah untuk tujuan green
budding ditanam dipolibag. Ukuran
polibeg yang direkomendasikan
adalah 50 cm x 25 cm x 0.15 mm
dengan kira-kira 30 lobang, 30 cm
dari bagian bawah lobang.
(ii) Polybag diisi penuh sampai 2 cm di
bawah bibir polybag, dengan jenis
tanah baik. Jika struktur tanah berat,
campur dengan pasir yang kasar.
(iii) Setelah pengisian tanah di polibag
maka aduk permukaan tanah dengan
pupuk TSP 10gr dan NPK 15.15.6.4,
10gr/ polibag sebagai pupuk dasar.
(iv) Sebelum polibag disusun, terlebih
dahulu jalur polibag dilapisi plastik
transparan ketebalan 0.04mm agar
menghambat akar menembus ke
tanah.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 11 of 33
(v) The polybags are arranged in twin
lines with the direction of east – west,
and the interlines spacing of 60 cm or
be adjusted to field condition.
1.1.5.1 Seedling planting
(i) The seeds are germinated in germination
bed prior to polybag planting. Good
seed will germinate within 7– 14 days
in the beds. It is advisable to discard
the seeds which have not germinated
after 14 days in the germination bed.
(ii) It is not acceptable to germinate the
seed in the polybag, because of it leads
to retarded growth of the seedling
roots due to relatively compact
structure of the soil in the polybag.
(iii) Plant 3 seeds per polybag and reduce
to 1 seedling after 7-14 days and after
1 month reduce the seedling to 1 best
seedling remains per polybag
(iv) If there is no good seedling in the
polybag replace with a germinated
seeds. Do not pull a seedling from
another polybag as a “supply”.
(v) Polybag disusun berbaris ganda arah
Timur – Barat dengan jarak antar
baris 60cm atau disesuaikan dengan
kondisi lapangan.
1.1.5.1 Penanaman kecambah
(i) Biji terlebih dahulu dikecambahkan di
bedeng pengecambahan sebelum
ditanam dipolybag. Biji yang baik
berkecambah dalam 7-14 hari.
Dianjurkan membuang biji yang
tidak berkecambah setelah 14 hari.
(ii) Hindarkan menanam biji langsung di
polybag, karena menyebabkan
pertumbuhan akar kecambah
bengkok akibat struktur tanah
polibeg yang relatif padat.
(iii) Tanam 3 kecambah per polybag dan
kurangi menjadi 2 bibit pada saat 14
hari dan setelah 1 bulan pilih bibit
yang terbaik untuk dipertahankan .
(iv) Jika tidak ada kecambah yang baik di
polybag, ganti dengan biji yang baru
berkecambah. Jangan mencabut dari
polybag lain untuk menyisip.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 12 of 33
(v) When picking out the seeds care must
be taken to avoid the damage of the
roots or shoots whilst transferring to
the polybag. When planting out they
must be as in the germination bed with
radicle downwards.
1.1.5.2 Manuring
1.1.5.2.1 Manuring the rootstock in the
polybag
(i) For the purpose of basic manuring mix
10g TSP and 10g NPK 15:15:6:4 with
the soil of the top half of the polybag
before planting the seedling into
polybag. For the next manuring refers
the schedule as below
(ii) Manuring for budded seedlings when
the first whorl from the new scion are
(v) Hati-hati ketika mencabut kecambah
agar tidak merusak akar dan tunas,
juga saat memindahkan ke polybag.
Ketika menanam, posisi kecambah
harus ditanam seperti dibedengan
dengan radikula mengarah ke bawah.
1.1.5.2 Pemupukan
1.1.5.2.1. Pemupukan batang bawah di
polybag
(i) Untuk pupuk dasar di polybag campur
10g TSP dan 10g NPK 15:15:6:4
dengan setengah bagian tanah atas
sebelum menanam kecambah
kedalam polybag. Selanjutnya
dipupuk dengan jadwal di bawah ini:
(ii) Pemupukan untuk batang atas dimulai
jika daun payung pertama dari mata
Manuring for polybag seedlings
Month after planting Dossage
1 6 gr/polybag NPK 15.15.6.4
2 4 gr/polybag NPK 15.15.6.4
3 4 gr/polybag NPK 15.15.6.4
Catatan : It is not recommended to apply fertilizer 1 month prior
to budding, either for ferrous-containing fungicide application
Table 1. Manuring for polybag seedlings
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 13 of 33
hardened, apply 4 g NPK 15:15:6:4
every 2 weeks.
(iii) If the leafappear pale, apply urea
solution to the plants (30 g urea in 10 l
water for 200 polybag).
1.1.5.3 Watering
(i) Polybag soil should be maintained moist
by liberal applications of water in the
early morning or evening. More may
be required if plants are fully exposed
to sunlight.
(ii) It is recommended to calibrate the
watering in order to water supply is
equivalent with 8 mm perday rainfall.
If the nursery has the rainfall of 8-16
mm the watering should once per day
otherwise no watering needed if the
rainfall more than 16 mm.
okulasi telah mengeras berikan 4 gr
NPK 15:15:6:4 setiap 2 minggu.
(iii) Jika daun tampak pucat, berikan
larutan urea kedalam polybag (30g
urea/ 10 l air untuk 200 polybag).
1.1.5.3 Penyiraman
(i) Tanah dalam polybag dijaga agar tetap
lembab dengan menyiramkan air pagi
dan sore. Penyiraman yang lebih
diperlukan jika tanaman langsung
terkena sinar matahari.
(ii) Disarankan untuk melakukan kalibrasi
penyiraman agar pemberian air setara
dengan curah hujan 8 mm/hari.
Apabila curah hujan di bibitan 8-16
mm penyiraman cukup 1 kali sehari,
bila curah hujan > 16 mm tidak perlu
dilakukan penyiraman.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 14 of 33
Figure 1.3a Germination bed
Figure 1.3b Seeds arrangement in germination bed
Figure 1.3a Germination bed
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 15 of 33
1.1.6 Pest
If necessary rat and snail bait should be
distributed when seed is planted and for
at least 8 weeks after budding.
Thereafter, bait as necessary. Other pest
should be dealt with as below :
Remarks :
Thiodan 35 ; Spray over top flushes
covering both surfaces. Repeat once again
after 5 days. This insecticide is best if mite
and thrip attack all together.
Kerosene soap emulsion
Spray to cover all parts of the plant.
Repeat once or twice at weekly intervals
* Stock solution is made by dissolving
100 g soft soap in 1 ltr of hot water
nd emulsified with 100 ml kerosene
1.1.6 Hama
Jika perlu umpan tikus dan siput harus
disebarkan pada waktu penanaman biji dan
sekurangnya 8 minggu setelah okulasi.
Pasang umpan bila perlu. Hama lain harus
dikendalikan dengan cara sebagai berikut :
Keterangan :
Thiodan 35 ; Semprot di permukaan atas
dan bawah daun muda. Ulangi setelah 5
hari. Insektisida ini paling baik digunakan
jika tungau dan kutu menyerang serentak
Larutan sabun kerosene
Semprotkan ke semua bagian tanaman.
Ulangi seminggu atau 2 minggu sekali
* Larutan stok dibuat dengan melarutkan
100 g deterjen dalam 1 ltr air panas,
diemulsi dengan 100 ml minyak tanah.
Pest Insecticide Rate of
Application
Dilution
% of
Formulation
Rate
% a.i
Spray
Equipment
Mites &
Thrips
Scale
insects &
mealybug
Caterpillars
& beetles
Thiodan 35
Kerosene-
soft soap
emulsion*
Azodrin 15
Dipterex
95 SP
3 ml/l water
-
-
-
1 ml/l water
2 g/l water
0.3
250 ml stock
solution in 1 l
water
0.1
0.2
0.11
“
0.06
0.19
Knapsack
“
“
“
Table 2. Metode pengendalian hama
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 16 of 33
1.1.7 Disease
(i) In good nurseries disease are not a
problem. Where fungicide treatment
is deemed economically necessary
the following treatments are
recommended at weekly.
(ii) The seedling leaves in the nursery
should be kept well maintained since
poor leaves will cause retardation of
the seedlings growth as well as
delaying planting program.
The budded seedling leaves are sensitive
to diseases infectious strage during the
nursery. Apply the fungicide immediately.
After it has rained and in dry season at
every 2 weeks interval.
1.1.7 Penyakit
(i) Pada pembibitan yang baik penyakit
biasanya bukan masalah. Jika
pengendalian dengan fungisida secara
ekonomis dianggap perlu, perlakuan
berikut direkomendasikan mingguan
.
(ii) Pertumbuhan daun di bibitan harus
dijaga karena bila pertumbuhan daun
lambat akan menghambat pertumbuhan
bibit dan menghambat program
penanaman.
Pertumbuhan daun pada masa pembibitan
sangat peka terhadap serangan penyakit
daun. Jika hujan, maka setelah reda segera
disemprot dengan fungisida. Jika tidak
hujan penyemprotan 2x seminggu.
Disease
Fungicide Consentration Interval
Oidium
Gloeosporium
Helminthosporium
Calixin-750 0.15% Every two weeks
Dithane M-45 0.3% Weekly
Antracol 0.2% Weekly
Dithane M-45 0.3% Weekly
Daconil 0.2% Weekly
Table 3. Metode pengendalian penyakit
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 17 of 33
1.1.8 Selection/culling
(i) At 14 days after germination, culling
should be carried out on retarded
seedlings as well as seedlings
without leaves or seedlings which
grow with more than 1 apical shoots.
(ii) At 1 month after germination, culling
on the less vigorous seedling in
other that only the most vigorous
seedling remains for budding
(iii) Prior to budding the culling is done
to unvigorous, dwarf, and thin
seedlings with small trunk diameter.
1.1.8 Seleksi/culling
(i) Pada umur 14 hari lakukan seleksi
terhadap tanaman yang berkembang
tidak sempurna; yaitu tanaman yang
gagal membentuk daun atau yang
mempunyai tunas pucuk > 1.
(ii) Umur 1 bulan, seleksi satu tanaman
lainnya per polibag dan tinggalkan 1
tanaman yang paling jagur untuk
dipelihara untuk okulasi.
(iii) Menjelang okulasi, seleksi tanaman
yang pertumbuhannya tidak bagus,
tanaman kerdil, diameter sangat kecil.
Figure 1.5 Tool for measuring the diameter of rootstock
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 18 of 33
Note : 5-7 months old 11 mm
8 months old 13 mm
9 months old 15 mm
10 months old 17 mm
1.1.9 Budding
(i) At 3 months after polybag planting;
the seedlings reach a diameter of 6-8
mm; at 10 cm above the ground
level, will be ready for budding.
Budding could be done until the
seedlings 4-5 months old.
(ii) The budding could be done in all
growth stages of the upper whorl;
i.e. in flush or mature leaves stage.
(iii) Remove soils and sands from the
rootstock.
(iv) By using a sharp knife perform a cut
of 6 - 8 mm wide horizontal or 1/3
of trunk diameter made onto the
rootstock to cambium depth, 7-8 cm
height from the ground level. Used a
special budding knife which is
smaller than conventional knife.
(v) The bark is peeled 3-4cm upwards
carefully until exposing the
cambium.
Catatan : 5 -7 bulan 11 mm
8 bulan 13 mm
9 bulan 15 mm
10 bulan 17 mm
1.1.9 Pengokulasian.
(i) Pada umur 3 bulan setelah tanam
diameter batang mencapai + 6-8mm
pada ketinggian 10cm dari permukaan
tanah, sudah mulai dapat diokulasi.
Okulasi dapat dilakukan sampai bibit
berumur 4-5 bulan.
(ii) Okulasi dapat dilakukan pada setiap
tahap perkembangan daun teratas; sejak
flush sampai daun berwarna hijau tua.
(iii) Bersihkan batang dari tanah dan pasir.
(iv) Dengan pisau tajam, buat potongan
horizontal selebar 6 - 8 mm atau 1/3
bagian lilit batang bawah sampai ke
kambium dengan ketinggian 7-8 cm
dari permukaan tanah. Gunakan pisau
okulasi yang lebih kecil daripada pisau
okulasi konvensional.
(v) Kulit dikupas 3-4 cm kearah atas
secara hati-hati sehingga tampak
kambiumnya.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 19 of 33
(vi) A bud patch about the same size as
the exposed panel, with centrally
sited the bud, about 2 cm above its
base is carefully removed from the
budstick. Do not touch the back of
the budpatch.
(vii) The freshly cut budpatch is placed
inside the newly opened panel. The
peeled bark of the rootstock should
be cut off.
(viii) Secure the patch with translucent
polythene tape, 2 cm wide, 0.15 mm
thick. Bind the tape upward and
clockwise overlapping on each turn.
The tape is about 30 cm long.
(ix) Budding should be opened 21 days
after budding. The success budding
marked by fresh green occurred at
budding point.
(x) The cut back is performed 25 cm
above the bud. The cut surface
loated by coalter.
(xi) It is recommended to to cut back all
succcesfull buddings in a bed at one
(vi) Mata okulasi berukuran sama dengan
jendela batang bawah, mata tunasnya
+2cm diatas dasarnya, diambil dengan
hati-hati dari batang entres. jangan
pegang belakang mata okulasi.
(vii) Mata okulasi yang baru dipotong
diletakkan pada panel yang baru
dibuka. Kulit batang bawah yang
terbuka harus dipotong.
(viii)Balut mata okulasi dengan plastik
transparan lebar 2 cm, tebal 0.15 mm,
ikat dari bawah keatas searah jarum
jam dan selalu menumpang setiap
memutar. panjang plastik 30 cm.
(ix) Budding harus dibuka 21 hari setelah
pelaksanaan okulasi. Okulasi yang
berhasil ditandai dari perisai mata yang
tetap berwarna hijau.
(x) Cut back 25cm di atas tunas pada 6-7
hari setelah pembukaan budding,.
Bekas potongan dioles dengan coalter.
(xi) Potong semua okulasi yang berhasil
sekaligus setelah pengokulasian dan
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 20 of 33
time after the 2nd
round of budding
and opening. Do not leave any
seedling stocks with or without
grafts, but cut every plant. Third
round budding should not be done.
1.1.10 Cutting back techniques
(i) Budding should start in April and
finish by the end of June.
(ii) Seedling stock should ideally exceed
11 mm in diameter at the time of
budding. A Special tool can be used
to measure the diameter of seedling
stock as shown on Figure 1.5
1.1.11 Pruning the watershoots
The emerging stock shoots or waters
hoots should be pruned with a sharp
knife.Until the graft bud has started
growing, prune every 2 days. Later
pruning rounds are 5 of days. Avoid
plucking with fingers.
1.1.12 Preparation For Field Planting
(i) Field Planting is best done after the
1st whorl leaves has fully hardened.
If nursery preparation has fallen
pembukaan okulasi pusingan kedua.
Semua batang bawah yang diokulasi
dan tidak diokulasi dipotong , jangan
ada yang tersisa. Jangan melakukan
okulasi pusingan ketiga.
1.1.10 Teknik cutting back
(i) Okulasi harus dimulai bulan April dan
selesai bulan Juni.
(ii) Besar batang bawah sebaiknya
berdiameter lebih dari 11 mm pada
waktu budding. Dapat digunakan alat
khusus untuk mengukur besar batang
bawah seperti pada gambar 1.5
1.1.11 Penunasan
Tunas yang tumbuh selain dari mata okulasi
ditunas menggunakan pisau tajam. Sampai
mata okulasi mulai membengkak, lakukan
penunasan setiap 2 hari. Rotasi penunasan
selanjutnya adalah 5 hari. Hindari menunas
menggunakan jari tangan.
1.1.12 Persiapan Tanam Ke Lapangan
(i) Penanaman ke lapangan paling baik
pada saat daun payung kedua telah
mengeras. Jika persiapan pembibitan
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 21 of 33
behind schedule it is possible to
plant after the 1st whorl has hardened
and the next whorl has newly
emerged if favourable weather
prevails.
(ii) The selection must be done by an
experienced staff. Under normal
circumstances 80-90% of the plants
should suitable for field planting.
Only those with fully hardened
leaves should be planted out.
Immature plants are to be retained
until the foliage has fully matured.
(iii) Plants have to be handled with great
care but should not be over watered
before planting out as the soil may
collapse before the plastic bag is
fully removed resulting in
transplanting shock or even death.
(iv) When planting, the bottom of the
bag is slit open with a razor blade,
the plant is then correctly placed in
the hole with the budpatch 10 cm
under ground level. Next, cut the
side of the bag from bottom
upwards. Progressively remove the
terlambat dari jadwal, bibit dapat
ditanam setelah daun payung pertama
mengeras dan daun payung berikutnya
sudah mulai muncul dan cuaca
mendukung.
(ii) Seleksi tanaman harus dilakukan oleh
staff berpengalaman. Pada keadaan
normal akan diperoleh 80-90% bibit
layak tanam. Bibit yang daunnya telah
mengeras yang boleh ditanam.
Tanamanyang daunnya belum
mengeras harus ditinggal dibibitan
sampai daunnya mengeras.
(iii) Tanaman ditangani dengan hati-hati,
jangan terlalu banyak disiram sebelum
menanam karena tanahnya akan hancur
sebelum polybag dipindah, serta
menyebabkan transplant shock bahkan
mungkin mati.
(iv) Sewaktu menanam, dasar polybag
dibuka dengan pisau silet, kemudian
tanaman diletakkan tepat ditengah
lubang dengan mata okulasi 10cm di
bawah permukaan tanah. Potong bagian
sisi polybag dari bawah ke atas. Secara
bertahap tarik polybag ketika mengisi
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 22 of 33
bag whilst filling the hole, gently
tamping in.
1.2 Developing Budwood Garden
Budwood garden constitute of a garden
that produce stems contain budpatchs that
will utilize in the vegetative propagation
through budding. To assure the origin of
the clones, the planting material should be
under the recommendataion of
government Rubber Research Institute.
lobang dan perlahan padatkan.
1.2 Pembangunan Kebun Entres
Kebun entres, merupakan kebun penghasil
mata tunas yang akan digunakan sebagai
batang atas dalam perbanyakan tanaman
karet secara okulasi. Untuk menjamin
kemurnian klon, bahan tanam untuk kebun
entres harus mendapat rekomendasi dari
Balai Penelitian Karet.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 23 of 33
1.2.1 Site requirements
The site of budwood garden should be :
1. The site should be flat
2. Close to access road and water source
3. Not liable for flooding
4. Accessible and monitorable
5. Free from disease inoculum
6. Having good soil structure, texture
7. Close to the nursery
1.2.2 Soil tillage
(i) All the side trees should be felled
and total up rooting, and subsequent
stacking at the outerside.
(ii) The mechanical tillage should be
done to mitigate the infection of
WRD due to high density of tree
population.
(iii) The tillage is done by 2 times ripping
following by 2 times ploughing and
subsequent harrowing. The 2nd
ripping is done by cross the 1st
ripping. The 1st ploughing cross to
2nd
ripping and 2nd
ploughing cross
to 1st ploughing. The depth of
ripping at least 50 cm, and the depth
of ploughing at least of 28 cm.
1.2.1 Syarat lokasi
Lokasi kebun entres sebaiknya :
1. Tofografi rata, kemiringan 0-10%
2. Dekat dengan jalan dan sumber air
3. Tidak tergenang air
4. Mudah diawasi/dicapai
5. Lokasi bebas dari sumber penyakit
6. Struktur, tekstur tanahnya baik
7. Dekat dengan lokasi pembibitan
1.2.2 Pengolahan tanah
(i) Semua pohon di areal pebibitan harus
ditumbang, akar dibongkar bersih dan
dikumpulkan di luar areal.
(ii) Pengolahan tanah secara mekanis, untuk
mengurangi tingkat serangan penyakit
JAP akibat populasi tanaman yang
tinggi.
(iii) Pengolahan tanah dengan 2 kali
ripping, 2 kali luku dan n garu. Ripping
kedua menyilang tegak lurus dari
ripping pertama. Luku pertama
menyilang tegak lurus dari ripping
kedua dan luku kedua menyilang tegak
lurus dari luku pertama. Kedalaman
ripping minimal 50 cm dan kedalaman
luku minimal 28 cm.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 24 of 33
(iv) The interval of the tillages are 2
weeks, each following by root
collection to remove all the
persistent roots. The root collection
by “giring system” with the interval
between each worker at 1- 2 m.
1.2.3 Planting
Every budwood gardens contains of
various recommended clones. Each clone
is planted in separated sub-block with the
interval of 2 metres. Each sub-block
contains of 100 budwood trees.
(i) The clone informations signboard
should contains of :
• Block identification; contains
information of block number,
name of clones, and the
number of sub-blocks.
• The main signboard contains
information of ownership,
hectarage, and the number of
trees. All information should
be oil painting.
(iv) Interval pengolahan tanah minimal 2
minggu, selalu dikuti dengan ayap akar
untuk membuang sisa akar tanaman
lama. Ayap akar dilakukan dengan
sistem giring dengan jarak antara dua
pekerja 1-2 m.
1.2.3 Penanaman
Dalam setiap kebun entres biasanya terdapat
beberapa klon anjuran. Setiap klon ditanam
pada petak yang terpisah dengan klon lain,
jarak antar petak 2 meter. Pada setiap petak
terdapat 100 pohon entres.
(i) Buat papan tanda penempatan klon
berisi informasi :
• Papan nama blok; berisi informasi
nomor blok, nama klon dan
jumlah petak.
• Papan induk; berisi nama pemilik,
luas hektar, jumlah pohon, nama
klon dan tahun tanam. Penandaan
pada semua papan menggunakan
cat minyak.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 25 of 33
(ii) The block and sub-block signboards
are placed at the corner of block and
block closer to control road, while
the main signboard placed at the
roadside.
(iii) The plating points of budwood garden
are of 1m x 1m. After cutback 10%
of the area for road utility, the
population of budwood trees are
9000 trees per ha.
(iv) The planting hole should be 60cm x
40cm x 40cm. The manuring in the
planting hole subject to prevailing
Fertilizer Recommendation.
(v) The planting materials that commonly
planted in the budwood gardens are
2 whorls polybag seddlings.
1.2.4 Maintenance
(i) Manual weeding should be done
during 6 months after field planting
with the rotations of 2-3 months.
(ii) When the rootstocks indicating brown
in color, weeding by spraying with
the rotation of 3 months. Care
(ii) Papan nama petak dan blok ditempatkan
disudut petak dan blok yang dekat
dengan jalan control sedangkan papan
induk ditempatkan di tepi jalan.
(iii) Pemancangan jarak tanam di kebun
entres adalah 1m x 1m. Setelah
dipotong 10% dari luas lahan untuk
jalan, jumlah pohon entres per hektar
adalah 9.000 pohon.
(iv) Lobang tanaman dibuat dengan ukuran
60 x 40 x 40 cm. Pemupukan dasar
pada lubang tanam mengikuti
rekomendasi pemupukan yang berlaku.
(v) Bahan tanam yang lazim digunakan
untuk kebun entres adalah bahan tanam
polibag berpayung daun dua.
1.2.4 Pemeliharaan
(i) Penyiangan gulma terutama pada enam
bulan pertama setelah tanam dilakukan
secara manual dengan rotasi 2-3 bulan.
(ii) Pada saat batang sudah berwarna coklat,
penyiangan secara kimia dengan rotasi
3 bulan, tetapi harus hati – hati karena
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 26 of 33
should be taken due to herbicide can
affect to plant scorching. The
watershoot should be removed
during it still young, with the
rotation of two weeks.
(iii) The fertilizer application in budwood
garden subject to Rubber Fertilizer
Recommendation by Agronomist
(iv) Manuring by spreading the fertilizer
evenly between the planting row.
Manuring application is done during
good soil moisture and weed free.
(v) The common disease in the budwood
garden are of the same with the
disease infected the nursery. The
disease control can be seen in the
chapter 12 (Pest and Disease).
1.2.5 Harvesting the brown budwood
and shaping the the canopy trees
(i) For the 7-12 months budding, when
the rootstock indicating brown in
color, the budwood harvested at > 8
- 12 months old. During the 1st year
dapat merusak pohon entres jika kontak
langsung dengan herbisida. Tunas liar
pada batang entres harus dibuang saat
masih muda dengan rotasi dua minggu.
(iii) Pemupukan tanaman karet pada kebun
entres mengikuti rekomendasi
pemupukan karet oleh Agronomis.
(iv) Pemupukan secara merata diantara
barisan tanaman. Pemupukan dilakukan
pada saat keadaan tanah lembab dan
bebas gulma.
(v) Penyakit yang umum dijumpai di kebun
entres hampir sama dengan penyakit
yang umum menyerang tanaman di
pembibitan. Cara pengendalian dapat
dilihat pada Bab I2 (Pest And Disease).
1.2.5 Pemanenan entres untuk Okulasi
Coklat dan pembentukan tajuk
(i) Untuk okulasi batang bawah berumur 7-
12 bulan, pada saat batang berwarna
coklat, entres dapat dipanen pada umur
≥ 8-12 bulan. Pada tahun pertama, dari
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 27 of 33
a budwood tree produce 1 pcs
budwood stick.
(ii) All the budwood trees should be
cutback after budding in the current
year nursery has been done.
(iii) The budwoods are harvested by
cutting the branches at 30-40 cm
above the gorund level just above
the whorl at the cutting slope 45o.
The cutting surface coating with TB
192.
(iv) One or two weeks after harvesting,
all watershoots should be removed
exept of two vigorous shoots
remains growing for further harvest.
Pruning should be done during the
watershoots are in young phase.
(v) The 2nd
harvesting carried out by
cutting the budwood 20 cm above
the growing base. Each budwood
tree will produce 2 budwood stick.
The wild watershoots should be
removed exept of two vigorous
shoots remains growing for further
harvest.
satu pohon entres hanya diperoleh 1
cabang entres.
(ii) Setiap tahun semua pohon entres harus
di dipotong setelah selesai okulasi pada
bibitan tahun berjalan.
(iii) Entres dipanen dengan pemotongan
cabang pada ketinggian 30-40 cm dari
permukaan tanah atau diatas payung
daun dengan kemiringan potongan 450.
Luka potongan dioles dengan TB 192.
(iv) Satu atau dua minggu setelah
pemotongan cabang entres, semua
tunas dibuang kecuali disisakan dua
tunas yang terjagur untuk panen
selanjutnya. Pruning dilakukan pada
saat tunas masih muda.
(v) Panen entres kedua dilakukan dengan
cara memotong entres pada ketinggian
20 cm dari pangkal tempat tumbuhnya.
Dari setiap pohon entres akan diperoleh
2 cabang entres. Tunas yang tumbuh
dari setiap cabang hanya dipelihara dua
tunas yang terjagur.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 28 of 33
(vi) The 3rd
harvesting will produce 4 bud
wood sticks from each budwood
tree.
(vii) It is not recommended to cut all the
budwood branches altogether, due to
stagnation of the plants and leaves
emerge all at once resulting plant
succeptibility to leaf diseases. For
further harvesting, the branches
remains for growing are not more
than 4 branches per tree.
(viii) The amount of budpatch per metre
budwood of clone RRIC 100 are of
8-10, while clone PB260 has 10-14.
1.2.6 Budwood for green budding
(i) For the purpose of green budding (3-
4 months old), the budwood to be
utilize are of 3-4 months old or at
the same age with the rootstock. To
gain so, the budwood branches are
cutback at 2.5 – 3.5 months prior to
budding.
(ii) During the 1st year, 6 month after
field planting, the trunks are cutback
(vi) Pada panen ketiga, 4 cabang diperoleh
dari setiap pohon entres.
(vi) Pemotongan tajuk sekaligus dalam
waktu yang bersamaan tidak dianjurkan
karena batang utama dapat mengalami
stagnasi. Selain itu, akan
menumbuhkan daun secara serentak
sehingga rentan terhadap penyakit
daun. Untuk tahun-tahun berikutnya,
tunas yang dipelihara per pohon entres
sebaiknya tidak lebih dari empat.
(vii) Jumlah tunas okulasi per meter
entres pada klon RRIC100 yaitu 8-
10, pada klon PB 260; 10-14 mata.
1.2.6 Entres untuk green budding
(i) Untuk okulasi green budding (berumur
3-4 bulan), entres yang digunakan
berumur 3-4 bulan atau umurnya
hampir sama dengan umur batang
bawah. Untuk mendapatkan entres
seperti itu, maka pohon entres dipotong
3-4 bulan sebelum okulasi.
(ii) Pada tahun pertama, 6 bulan setelah
tanam, batang pohon entres dipotong
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 29 of 33
at 50 – 60 cm above the ground
level. Commonly each tree will
produce 6 – 8 young shoots. The
budpatch which is to be used in
green budding is scion or budpatch
llaying on rudimetre leaves. A
young shoot will produce 3 scions.
(iii) In the such situation, the leafscion
can be used as budpatch by cutting
the leaves petiole, then can be
utilized after 10-14 days.
(iv) During harvesting young budwood 2
vigorous young shoots remains
growing for further harvest.
(v) In the 2nd
year, at 2-3 months prior to
green budding both growing shoots
are to be cut 30 cm above the 1st cut.
Furthermore, all emerging shoots
remains growing until it reach one
whorl stadium.
(vi) Each tree will produce 10-14 young
shoots. Harvesting should be done in
the morning prior to budding.
(vii) The site of young budwood garden
preferable close to the nursery so
pada ketinggian 50-60 cm dari
permukaan tanah. Dari dari satu pohon
entres diperoleh 6-8 tunas. Mata
okulasi untuk green budding adalah
mata sisik atau mata yang berada pada
bekas daun yang rudimenter. Satu tunas
muda menghasilkan 3 mata sisik.
(iii)Dalam kondisi tertentu mata daun dapat
digunakan dengan memangkas tangkai
daun, setelah 10-14 hari kemudian baru
dapat digunakan untuk okulasi.
(iv) Pada saat panen entres muda, disisakan
sebanyak 2 tunas untuk dipanen
selanjutnya.
(v) Pada tahun kedua, 2-3 bulan sebelum
okulasi, kedua tunas yang dibiarkan
tumbuh pada tahun I dipotong pada
ketinggian 30 cm dari bekas
pemotongan I. Tunas yang tumbuh
dipelihara sampai stadia payung satu.
(vi) Dari setiap pohon entres akan diperoleh
10-14 tunas. Untuk entres muda, panen
dilakukan pagi hari sebelum okulasi.
(vii)Kebun entres muda sebaiknya
berdekatan dengan lokasi pembibitan,
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 30 of 33
harvested budwood can immediately
used for budding in the same day.
1.2.7 Packaging budwood for
forwarding
(i) As soon as the budwoods has been
cut, quick dip the budwood tip in the
liquid wax to prevent dryness. It is
not recommende too longer-dip due
to hot damage of budwood tissues.
(ii) For the purpose of 2 days distance
forwarding, budwood are 1 meter
cut and subsequent quick dip in
liquid wax prior to package in the 50
x 50 x 120 cm wooden box which
can loaded with 75-100 pieces
budwood sticks. Fill the box base
with sawdust 1-1.5 cm tick prior to
loading the budwoods.
(iii) Arrange the budwoods in layers and
each layer is covered by moist
sawdust.
(iv) Clossing the box cover and
thightening with nails. It is not
recommended to >2 days forwarding
due to dryness of the budpatch.
supaya entres yang dipanen dapat
dipakai pada hari yang sama.
1.2.7 Pengemasan entres untuk
pengiriman
(i) Segera setelah entres dipotong,
ujungnya dicelup pada lilin cair.
Tujuannya adalah agar entres tidak
mengalami kekeringan. Pencelupan
tidak boleh terlalu lama karena dapat
merusak jaringan akibat panas.
(ii) Pengiriman jauh yang memerlukan
waktu 2 hari, entres dikemas setelah
dipotong sepanjang 1 m, kedua
ujungnya dicelup kedalam lilin cair
kemudian dimasukkan kedalam peti
kayu berukuran 50 x 50 x 120 cm
kapasitas 75-100 entres. Sebelumnya
bagian bawah peti kayu ditaburi serbuk
gergaji dengan ketebalan 1-1.5 cm.
(iii) Entres disusun secara berlapis dan
setiap lapis ditaburi serbuk gergaji
lembab.
(iv) Selanjutnya peti ditutup dan dipaku.
Pengiriman jarak jauh sebaiknya tidak
lebih dari dua hari karena menyebabkan
mata tunas menjadi kering.
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 31 of 33
(v) During at the destination the opened
budwood box should be placed in
the shaded area and the budwood
should be used as soon as possible.
(vi) For short distance forwarding
(maximum of 1 day), the budwoods
covered by 2 layers of moist papers
or banana stems. Avoid loading too
much budwood in one package due
to damage by frictions.
1.2.8 Clones origination and budwood
rejuvenation
(i) Some watershoots may emerge from
rootstock or clonal contamination
may occurs during initial period.
(ii) First clone origination at 4-5 whorls
stage (8-10 months old) and further
works in every two years.
(iii) Clones origination should be done by
clone identification experts. be done
All trees should Identified. The
unspecified clones should be culled
and by subsequent infilling.
(iv) The budwood garden should be
rejuvenation in every 10 years to
(v) Setelah tiba di tempat tujuan, peti
entres ditempatkan di tempat yang
teduh dalam keadaan terbuka dan entres
segera dipakai.
(vi) Untuk pengiriman dekat (maksimal 1
hari) entres dibungkus dua lapis kertas
lembab atau pelepah pisang. Hindarkan
memuat entres terlalu banyak karena
menyebabkan kerusakan mata tunas
akibat bergesekan.
1.2.8 Pemurnian klon dan peremajaan
kebun entres.
(i) Tunas liar dapat tumbuh dari batang
bawah atau kontaminasi klon lain pada
bahan tanamam pada fase awal tanam.
(ii) Pemurnian klon yang pertama pada
tahap 4-5 payung daun (umur 8-10
bulan), selanjutnya setiap dua tahun.
(iii) Pemurnian klon dilakukan oleh tenaga
ahli di bidang identifikasi klon.Ssemua
pohon harus diidentifikasi . Pohon yang
tidak sesuai dengan spesifikasi klon
dibongkar kemudian disisip.
(iv) Kebun entres diremajakan setiap 10
tahun untuk mempertahankan
PT. TOLAN TIGA INDONESIA
Doc . No : 1 Issued Note
SOP/Rubber/ESD 1 October 2009
Rev.
1 Page
1 October 2009 32 of 33
maintain vigorous and juvenility.
The lack of juvenility means of
inferiority of vegetative growth lead
to generative phase.
(v) Avoid to harvest from >10 years old
trees, due to weak girth development
and adversely faster inflorescences
phase, that lead to longer immature
periodes.
kejaguran dan sifat juvenilitasnya.
Berkurangnya sifat juvenilitas tanaman
berarti pertumbuhan vegetatif lemah
dan tanaman cepat berbunga.
(v) Hindari mengambil mata okulasi dari
pohon entres berumur >10 tahun,
karena pertumbuhan lilit batang lebih
lambat dan tanaman cepat berbunga,
sehingga memperlambat masa TBM.
Figure 1.14.1 Kebun entres
top related