pspice introduction

PSPICE- IntroductionPSPICE- Introduction

PRESENTED BY:Akshay DholeAkshay Dhole

Mechatronics (SMBS)Mechatronics (SMBS)13mmt101313mmt1013

Course facultyDr. M. K. ChakravarthiDr. M. K. Chakravarthi

IndexIndex1. Introduction2. Types of analysis3. Circuit components4. File structures5. Libraries6. Parts7. Design structure8. Design example 9. Results10.Conclusion

IntroductionIntroduction• SPICE (Simulation Program for Integrated

Circuits Emphasis) is a general purpose analog circuit simulator that is used to verify circuit designs and to predict the circuit behavior.

• PSpice is a PC version of SPICE and HSpice is a version that runs on workstations and larger computers.

• PSpice has analog and digital libraries of standard components (such as NAND, NOR, flip-flops, and other digital gates, op amps, etc) which makes it a useful tool for a wide range of analog and digital applications.

Types of AnalysisTypes of Analysis• Non-linear DC analysis• Non-linear transient analysis• Linear AC Analysis• Noise analysis • Sensitivity analysis • Distortion analysis • Fourier analysis• Monte Carlo Analysis

Circuit ComponentsCircuit Components• Independent and dependent voltage and current sources • Resistors • Capacitors • Inductors • Mutual inductors • Transmission lines • Operational amplifiers • Switches • Diodes • Bipolar transistors • MOS transistors • JFET • MESFET • Digital gates

Terminologies Terminologies • Subcircuit: A subcircuit allows you to define a

collection of elements as a subcircuit (e.g. an operational amplifier) and to insert this description into the overall circuit.

• EDIF: Electronic Design Interchange Format, a standard published by EIA. Usually used for netlists.

File structure PSPICE File structure PSPICE (Capture)(Capture)

• Input file for PSpice that has the file type “.CIR” • When a circuit is simulated “.OUT” is generated• “*.DAT” file is by default a binary file to see the

data • “*.LIB” files where the details of complex parts

are saved• Additional files

o *.SCH (the schematic data, itself)o *.ALS (alias files)o *.NET (network connection files)

LibrariesLibraries• These are files that contain reusable part data.• They can be custom or default ones• Some of the libraries available in the Evaluation

version of PSPICE are: o abm.slb for special functions like square root and

multipliers o analog.slb for analog components like resistors and

capacitors o breakout.slb for pots o connect.slb, .plb for connectors o eval.slb, .plb for semiconductor, digital devices, switches o port.slb for grounds, high/low digital ports o special.slb for ammeters, viewpoints o source.slb for various analog and digital sources

PartsParts• Part is a basic building block which may represent

o One or more physical elemento Functiono Simulation modelo When a part is placed for first time its entry is done in “Design Cache”

What is “Design Cache”????... Go and Find Out Yourself

Design StructureDesign Structure• Flat Design

o Small designso All pages in same schematico Off Page connectors are

usedo Figure shows design hierarchy

• Hierarchical Designo Much complex designso Symbols are created called “Hierarchical Blocks”

Things to remember Things to remember before startingbefore starting

• PSpice is not case sensitive • All element names must be unique • There must be a node designated "0" (Zero). This

is the reference node against which all voltages are calculated.

• If any change is made in circuit make sure you create netlist again before simulating it.

Getting StartedGetting Started• File New Project Analog or Mixed A/D

Make sure to choose Analog or Mixed A/D and proper location for project

• Next comes following window

Make sure you select “Create a blank project”

• This is how a typical “Schematic” Window will look like

• Now start placing components and connecting them (this part is quite similar to what you have done in last semester’s lab)

Add a library as per the Requirement for eg. here analog library has been added

• After completing the circuit save it and run it.• Plot appropriate waveform by probing on circuit.

Design ExampleDesign Example• Take example of a high pass filter (RC)• First we will follow initial steps of creating a new

project • Now placing the components.

Place the componentsPlace the components

Place the source and Place the source and groundground

Add ProbeAdd Probe

Probes

Creating new Creating new simulation profilesimulation profile

• Go to PSPICE New Simulation Profile • Give a name to profile and create

AC AnalysisAC Analysis• We can choose any of the analysis and options• Here AC analysis is done to see operation of filter

Run Run • Go to PSPICE Run• Another waveform window will come up

Windowto keep track of current simulation

ResultResult

ConclusionConclusion• Thus we have learn the basics of P-Spice software

and it’s functioning theoretically.

• Its easy and simple software for simulations and analysis of the circuits.

Thank you