module v : emergency operations

NFPA ELECTRIC VEHICLE SAFETY FOR EMERGENCY RESPONDERS

Module V:Emergency Operations

5-1

NFPA ELECTRIC VEHICLE SAFETY FOR EMERGENCY RESPONDERS

Module V: Emergency Operations

Analyze simulated crash scenes to determineappropriate actions.

Terminal Objective

● Identify unique extrication challenges incrashes involving P/HEVs and EVs.

● Determine appropriate actions to extinguish a P/HEV or EV fire.

● Determine appropriate actions to handle a fire involving a P/HEV or EV battery.

Enabling Objectives

5-2

Module V Objectives

Introduction● Many procedures for response to

P/HEV and EV incidents are the same as for a conventional incident.

● However, there are some important differences. Learning to take appropriate action at P/HEV and EV incidents is critical.

5-3

NFPA ELECTRIC VEHICLE SAFETY FOR EMERGENCY RESPONDERS

Module V: Emergency Operations

Emergency Topics Addressed:

● Initial Response Procedures● Extrications● Battery Breaches● Submersion● Fire and Overhaul● Incidents involving charging stations

5-4

Module V Outline

Initial Procedures

● Scene Size Up.

● Utilize appropriate PPE for operations.

5-5

Identify

Immobilize

Disable

ExtricationStabilization● Standard cribbing methods are acceptable.

● Always place cribbing at vehicle structural points.

● Avoid fuel lines, high voltage cabling, etc.

5-6

Extrication● High voltage

components and cabling are usually not in typical “cut points.”

● Before conducting extrication operations, determine location of:● Occupant

Protection Systems● High Voltage

Components

5-7

Impact of Battery Location

● Trunk Tunneling - Some models’ batteries are located behind the rear seat.

● Through the Floor - high voltage cabling and batteries may be in the way.

5-8

Extrication

High Strength Steel● High strength / low weight metals are

used frequently in P/HEVs and EVs to enhance safety and fuel economy.

● Rescue tools that are suitable for these high strength metals must be used.

5-9

Extrication

Battery Breach

● Unlikely due to location and protective cases.

● Batteries are dry cell. Only a small amount of electrolyte would leak if crushed.

● Some models will leak liquid coolant.

● There is high voltage electrical shock hazard if a battery is breached.

● Follow local medical protocols in the event of exposure to electrolyte.

5-10

VideoVehicle

Submersion

5-11

Submersion● Vehicle shell is designed to not be a shock hazard.

● Damaged high voltage components could be a hazard.

● Electrical systems designed to NOT energize water.

● Ground fault circuit interrupters also provide protection.

5-12

Submersion

● Follow standard shutdown procedures.

● If access is a problem, remove the vehicle from water and then shut down.

● Note: Microbubbling may occur. This is NOT a shock hazard, but a natural result of electrolysis.

5-13

VideoVehicle Fires

5-14

Vehicle Fires● Use NFPA compliant firefighting PPE and respiratory protection. ● Utilize standard equipment for extinguishing any vehicle fire.

● Do NOT use equipment to pierce hood, due to HV components and cabling near surface.

● Follow normal emergency shutdown procedures.

5-15

Vehicle Fires

● Copious amounts of water recommended for a P/HEV or EV fire.

● Electrical systems designed to not energize water (including fire streams).

● After extinguishment, determine any HV battery involvement. Use thermal imaging equipment if available.

5-16

Vehicle Fires: Battery Involvement● If burning internally,

allow battery to burn itself out (if situation allows).

● Battery enclosure will impede direct extinguishment.

● Constant cooling of the outside of battery can slow, and may prevent, fire spreading to adjacent cells.

5-17

Vehicle Fires: Battery Involvement

As always, protect bystanders from exposure.

● Each type produces different byproducts when burning.

● Byproducts can be harmful, and require full PPE and SCBA in accordance with NFPA standards.

5-18

Overhaul● Avoid all high voltage components.

● Relays in the HV battery could be damaged or welded in closed position.

● Always treat the high voltage components as hazardous.

5-19

Incidents Involving Charging Stations

Fires● Treat as any

energized electrical fire in a structure.

● Shut down power to charging station.

● Perform extinguishment operations.

5-20

Incidents Involving Charging StationsCollision

● If a vehicle is struck while at charging station, turn off charging station power before operations.

● Identify, Immobilize, Disable.

● Shut down charging station power source.

5-21

Real World Incidents

5-22

The following slides contain images and anecdotal information from a series of actual vehicle crash scenes involving hybrid and electric vehicles.

5-23

5-24

Photo by Kevin Cooney

5-25

Photos by Kevin Cooney

5-26

Photos by Kevin Cooney

Activity 5.1

Emergency Operations

5-27

You will be given three scenarios. Each is an emergency incident involving a P/HEV or EV.

Working in your assigned group, answer the following questions for each scenario.

1. What did you gather from a size-up? What hazards are present?

2. What actions should be taken to: Ensure a safe work environment? Mitigate and Control the Incident?

5-28

Scenario 1

5-29

1. What did you gather from a size-up? What hazards are present?

2. Using your size up and experience, what actions should be taken to:

- Ensure a safe work environment? - Mitigate and Control the Incident?

5-30

Scenario 2

5-31

5-32

1. What did you gather from a size-up? What hazards are present?

2. Using your size up and experience, what actions should

be taken to: - Ensure a safe work environment? - Mitigate and Control the Incident?

Scenario 3

5-33

5-34

1. What did you gather from a size-up? What hazards are present?

2. Using your size up and experience, what actions should be taken to: - Ensure a safe work environment? - Mitigate and Control the Incident?

Many response procedures for P/HEV and EV incidents are the same as for incidents involving conventional vehicles. Special response considerations for P/HEV and EV incidents include:

IdentificationShut Down and ImmobilizationAvoiding High Voltage ComponentsBattery InvolvementHigh Strength SteelCharging Station Hazards

5-35

Module V Summary