microwave sdh product line

5th Generation Microwave

Feathers• Built-in ADM function

• Adaptive parameters adjusting

• Multi-service platform

• Software controlled system

Agenda1. General introduction

2. System architecture

3. Module and interface introduction

4. System configuration

5. Networking

6. System parameter

7. Application

8. Summery

SDH microwave introduction• 155M based high capacity digital microwave

• Widely operating frequency range

• Modulation RF BW≤28MHz

• 1xMbps wayside per 155M

• Support fast Ethernet and Gigabit Ethernet

• Up to 32E1 Add and drop function

• 4x63E1 cross connection funcion

• Small size: 1U high for 1+1

• Built-in SNMP and web

Modules introduction• Indoor unite（ IDU）

– Modem/IF

– Power

– Control & management

• order wire

• Wayside (1x2Mbps)

• 16E1 interface

– Mini interface

– Option interface

MW-SDH IDU

Standard PDH 1+0

Configuration

SDH 1+0 Configuration

• Part number: IDU-SO (STM-1 Optical, 1+0) or IDU-SW (STM-1 Electrical, 1+0)

– Consists of

– Chassis, Backplane

– 5 modules

• CCM-4800: Power Supply Module

• CCM-4500: Controller Module

• CCM-4100: Standard I/O Module

• CCM-4600: Modem and IF/Telemetry Module

• CCM-4155 or -4156: STM-1 Optical or Electrical Mini IO Module

SDH 1+0 Configuration• SDH 1+0 Capability: IDU-SO (STM-1 Optical, 1+0) or IDU-SW (STM-1 Elect

rical, 1+0)

• Dependent on available bandwidth: can adjust for operating bandwidth

– Payload Options (hardware is always available in unit)

• 100BaseTX Ethernet: scalable (from 1 – 100 Mbps)

• 1-16 x E1/T1: 2 x E1 (RJ-48C), 14xE1 (Molex 60-pin high density)

• STM-1 Optical or Electrical

• Skyway’s “Mode Configurator” tool to create any combination (assuming av

ailable bandwidth)

– Examples include

• STM-1 + 1 Mbps scaled Fast Ethernet

• STM-1 + 1 E1

• Other combinations that allow operation in 28/30 MHz bandwidth

SDH 1+1 Configuration

• Part number: IDU-SO (STM-1 Optical, 1+1) or IDU-SW (STM-1 Electrical, 1+1)

• Consists of

• Chassis, Backplane

– 7 modules

– CCM-4800: Power Supply Module, Qty2 each (for redundancy)

– CCM-4500: Controller Module

– CCM-4100: Standard I/O Module

– CCM-4600: Modem and IF/Telemetry Module, Qty2 each (for redundancy)

– CCM-4155 or -4156: STM-1 Optical or Electrical Mini IO Module

2+0 or East/West Configuration• Consecutive point architecture achieve

d with only a single 1 RU chassis at ea

ch location

• In this configuration the IDU contains 2

Power Supply Modules and 2 Modem/I

F Modules

• One Modem/IF is referred to as the we

st modem and the other as the east m

odem

• The IDU is connected to two ODUs, on

e broadcasting/receiving in one directi

ng of the ring architecture and the othe

r broadcasting/receiving in the other dir

ection

• This configuration provides

individual 1 + 1 link protection as

well as the full-scale protection

inherent in the consecutive point

architecture

• At each location within the

network, data may be dropped or

inserted

• Front panel connections for

drop/insert capability are provided

• In this configuration each IDU

contains 2 Power Supply Modules

and 2 Modem/IF Modules

Multi-hop Repeater with D/I Config

1+1 Protection: Diversity• Diversity mode: the link between each pair of modems is the same,

providing complete redundancy

• This arrangement requires bandwidth for both links and non-interfer

ence between the links, but it provides hitless receive and transmit s

witching

– The IDU supports both frequency and spatial diversity

– Frequency diversity: two frequencies are used

– Spatial diversity: two non-interfering paths are used

• In either case, the proprietary framer chooses the best, or error-free,

data stream and forwards it to the Line Interface Units (LIUs)

1+1 Protection: Non-Diversity• Non-diversity mode: One ODU at each location transmits to both two ODUs

at the other location

• Does not require the extra bandwidth or interference protection of diversity

mode

• Provides hitless receive switching and hot standby

• IDU automatically switches transmit ODU upon appropriate ODU alarm or O

DU interface error, minimizing transmit outage time

• The power supply, ODU, IF/telemetry and modem are protected

• The digital framing and LUIs are not

IDU: Options – PDH (IDU-PB 1+0) to Super PDH

– Additional 16xE1 + standard 16xE1 = 32xE1

• CCM-4132: 16E1 Expansion IO Module

• Software key to enable 32xE1 operation

– Status of 16E1 Expansion IO Module (CCM-4132)

• Integration complete

– SDH (IDU-SO or IDU-SW) with STM1-to-E1 Mux/Demux

• CCM-4132: 16E1 Expansion IO Module

• CCM-4100X: Standard IO with enhanced operation

– Software key to enable STM-1 to E1 (up to 32E1) Mux/Demux operati

on

– Status of STM1-to-E1 Mux/Demux

• Integration in progress

E1/T1 Cross-Connect Switch• Provides any-to-any connection between

– Front-panel E1/T1 ports (16 or 32)

– STM-1 payload (63xE1 or 84xT1)

– East Radio Link (63xE1 or 84xT1)

– West Radio Link (63xE1 or 84xT1)

• Mapping configurations may be developed in Excel and

uploaded to the IDU.

– Mappings are selected on the IDU via a drop-down box.

– Up to 32 pre-defined (via Excel) mappings may be specified

– A custom mapping can be edited directly on the IDU

• STM-1 Multiplex/Path Terminating

• Mux/Demux

• 63xE1

• 84xT1

– E1/T1 Cross-Connect Switch

– Any-to-Any connection of E1/T1 si

gnals

– 1+0/1+1 operation

– Up to 63xE1or 84xT1 over-the-air

• 2+0 operation

• Up to 126xE1 or 168xT1 over-the-

air

STM-1 MUX/DEMUX

Additional Options• Skyway would like Customer feedback on other network option

cards

– CCM-4132: 16E1/T1 Expansion IO

– In prototype verification

– CCM-4150: DS-3/E3/STS-1

• Single DS-3 or E3 or STS-1

– CCM-4xxx: Multi DS-3/E3/STS-1

• 3 x DS-3, 4xE3, 3xSTS-1

• The IDU cross point switch pro

vides any-to-any E1/T1 routing

between the front-panel ports,

east and west RF links.

• Flexible channel mapping allow

s pointand- click selection of pr

edefined routings or custom rou

ting.

• Custom routing selections may

be uploaded to the IDU via FTP.

16/32 E1 Crosspoint Capability

• Add/Drop Example: E1/T1s may be dropped from east or west to the front-panel ports.

16/32 E1 Crosspoint Capability

• The IDU STM-1 Mux/Demux

provides capability to

demultiplex 63xE1 (84xT1)

PDH signals from the SDH

signal.

• The demultiplexed E1/T1s are

routed via the crosspoint

switch to east, west, or

frontpanel.

• Enhanced IO (CCM-4120)

Module is required for this

function

Scalable SDHSTM-1 Mux/Demux Capability

• Outdoor unitOutdoor unit （（ ODUODU））– PowerPower– U/D transducerU/D transducer– HPAHPA– LNALNA– OMTOMT

Modules Introduction

ODU outdoor unit• Pure ideal physical characteristic

• Light weight, small size and low power consume

• Easy to change the polarization

• Low wind load

• Hard flange connector

• QCPSK/QPSK~128QAM Modulation

• Only 3.0KG

2002

2004

2008

2005

ODU Roadmap