microprocessors. von neumann architecture data and instructions in single read/write memory contents...

Microprocessors

Von Neumann architecture

• Data and instructions in single read/write memory

• Contents of memory addressable by location, independent of content

• Execution occurs in sequential fashion

HIGH Level View of CPU

CPU

• Internal Registers– Memory address register– Memory buffer resiter– I/O buffer register

ALU – Arithmetic Logic Unit

• Function units• Floating-point unit (FPU)

– Stack oriented

• Communication– Control and status buses– RISC has several– Input – registers, Output – via storage to

registers. Registers connected via signal paths.

ALU – continued

Control Unit

Control Unit – Function

• Fetch instruction, put it into IR, increment PC

• Decode and execute instruction

• Micro-orders

• Micro-instructions

• Micro-program

Control Units

• Microprogrammed– programmed

• Conventional– Hard-wired

• RISC vs CISC

Operations and IS

• Each instruction = 100, 1000, even 1000000 logic operations.

• 1 instruction triggers cascade of logical operations

CPU Hardwired design

• Instruction activates circuits– PLUS -> Provides for fast execution– MINUS -> no flexibility

• Changes in hardware of machine require changes in code which means changes in hardwiring

Microcode

• Developed by IBM

• Chip executes program – on nanoprocessor

• Plus -> easier to make complex processor

• Minus -> slower operation

• To compensate, microcode allows very complex instructions to be used; so fewer instructions are necessary

Register Set

• User-visible– General Purpose Registers– Data Registers– Address Registers– Condition code registers

• Negative, zero, positive, overflow

Register Set cont.

• Control and status registers– Program counter (PC)– Instruction register (IR)– Memory address register (MAR)– Memory buffer register(MBR)– Program status word(PSW)

Register Set cont.

• May have others – Process control block registers (PCBRs)

• On some systems both sets of registers are visible (so PC could be seen by user on some systems)

I/O System

• Consists of I/O devices and interface devices

• I/O interfaces stand between CPU and the I/O devices.

I/O Unit

• Matches timing and signal levels of CPU to devices. Since CPU has lower signal capacity, this involves going through signal buffers to strengthen it.

I/O handling

• CPU-controlled

• Memory-mapped

• Direct-memory access

CPU-controlled I/O

• “Write A to Device N”

• Challenge to keep CPU utilization high– Multiprogrammed Operating Systems– Multi-ported Memory Systems– I/O processors

• DMA channels, peripheral processing units (PPUs)

Memory-mapped I/O

• Memory addresses reserved for interface devises

• Each interface has several port addresses (control ports, status ports, input ports, output ports)

• Requires no special I/O instructions• CPU can’t distinguish I/O from normal

address operation

DMA I/O

• Hardware devices that directly control transfer of data

• No CPU intervention

• Interrupts CPU when finished

• Can control bus during transfer

DMA examples

• IBM – DMA Channels– Selector channels – multiple devices, one at a

time– Multiplexor channels – multiple devices

simultaneously

• Peripheral-processing units (Ppus) – Main frames – Control Data Corp.

Closer Look – Pentium III and 2

• P3– L1 cache - operating at speed of CPU– L2 cache 2M (in XEON 2M - 2GB)– 28.1 x 106 transistors

• P2– 7.5 x 106 transistors– 16K L1 instruction cache, and 16K data cache

Closer look continued

• P3– 2 ALUs, 2 FPUs– MMX unit

Clocked Logic

• Instructions are not carried out immediately as code signals reaches pins – there is a wait time

• Early processors did not execute 1 instruction/clock cycles, many instructions required as many as 100

Clocked Logic

• Using current RISC techniques, many instructions take less than 1 clock cycle (multiple ALUs, pipelined ALUs, SIMD, …)

• Clock multipliers allow CPU to run faster than system clock

• Basically, clock speed is not a good metric for different processors, just good indicator for identical processors with different speeds.

Clocked Logic

• Example: Suppose that processor P1 requires an average of six clock cycles per instruction and the system clock runs at 400 MHz. Processor P2 requires an average of two clock cycles per instruction and the system clock runs at 200 MHz.

•  • For P1 = 400 MHz / 6 cycles / instruction 67• For P2 = 200 MHz / 2 cycles / instruction 100•  

• Thus, (67 - 100)/67 -50% or P1 is 50% slower than P2 even

though it's clock speed is twice as fast as P1.

Modern CPUs

Need faster processing– Reduce number of steps microprocessor must

take• Make processor complex (so can combine steps)

• Make instructions simpler

• Operating on more than 1 instruction at a time (pipelining and superscalar)

Pentium II

• L2 cache – 512 K, not part of CPU (MCM)– Speed – ½ of CPU

• L1 cache double of that before to deal with bus bottleneck

• Bus Interface Unit – Data is duplicated to L1 and L2

• While fetch/Decode is pulling instructions, Branch Target Buffer looks for already completed instructions. BTB also looks for branching and predicts results with rate of 90%

Pentium II