manual de partes torre allmand nlpro ii
Post on 19-Jan-2016
117 Views
Preview:
DESCRIPTION
TRANSCRIPT
1
REVISED SEPTEMBER 2011
NIGHT LITE PRO II PARTS BOOK
INCLUDING AS3000 AUSTRALIAN SPEC
& CE SPEC
ALLMAND BROTHERS INC. P.O. BOX 888
HOLDREGE, NE 68949
PHONE: (308) 995- 4495, 1- 800- 562- 1373 ALLMAND FAX: (308) 995– 5887
ALLMAND PARTS DEPT. FAX : (308) 995– 4883
www.allmand.com
NIGHT LITE PRO II
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
2
NIGHT LITE PRO II 9/13/2011
RECORD
INDEX
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
3
NIGHT LITE PRO II 9/13/2011
SHO LAMP 1000W…….……………………..…………………………………..7
SHO LAMP 1250W……………………………………………………………….8
SHO LAMP HOLDER……………………….…………………………………....9
SHO LAMP ASSEMBLIES…………….…….…………………………………10
LIGHT BAR MANUAL WINCH TOWER….…………………………………...11
2 5/8 ROUND &3” TOWER SECTIONS...…………………………………….12
4” TOWER SECTION…………………………………………………………...13
INSTRUCTIONS FOR REPLACING CABLES-MANUAL TOWER………...14
PIVOT SECTION MANUAL WINCH TOWER (NEW)………….……………15
PIVOT SECTION MANUAL WINCH TOWER (OLD)………….…………….16
PEDESTAL MANUAL WINCH TOWER (NEW)……………………………...17
PEDESTAL MANUAL WINCH TOWER (OLD)..…………………..………...18
MANUAL WINCH - NON-CONTAINMENT TRAY…………..……………….19
MANUAL WINCH - CONTAINMENT TRAY…………………………………..20
ROTATIONAL LIGHT BAR VERTICAL TOWER…………………………….21
SECTION 6 VERTICAL TOWER……………………………………………...22
SECTION 5 VERTICAL TOWER……………………………………………...23
SECTION 4 VERTICALTOWER……………………………………………….24
SECTION 3 VERTICAL TOWER……………………………………………...25
SECTION 2 VERTICAL TOWER……………………………………………...26
SECTION 1 VERTICAL TOWER……………………………………………...27
INSTRUCTIONS FOR REPLACING CABLES– VERTICAL TOWER……..28
INSTRUCTIONS FOR REPLACING CABLES– VERTICAL TOWER……..29
NYCOIL VERTICAL TOWER…………………………………………………..30
VERTICAL TOWER PEDESTAL………………………………………………31
VERTICAL TOWER HYDRAULIC PUMP…………………………………….32
1250W - 60Hz BALLAST.………………………………………………………33
1000W - 60Hz (HPS)BALLAST………...………….………………………….34
1000W - 50HZ BALLAST……….……………………………………………...35
AXLE……………..……………………………………………………………….36
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
4
NIGHT LITE PRO II 9/13/2011
FRAME ………………..…………………………………………………………….37
FRAME - CE SPEC…………………………………….…………………………..38
TONGUE…...……………………………………………………………………….39
OUTRIGGERS……………………...……………………………………………...40
CONTAINMENT TRAY (OPTION)………..………...…………………………….41
ENGINE RAILS - NON CONTAINMENT TRA………………………..…………42
CONTAINMENT TRAY ENGINE PAN…..………...……………………………..43
KOHLER ENGINE………...….…………………………………………………….44
CAT ENGINE….…….……………………...………………………………………45
KUBOTA ENGINE…..……………………...……………………………………...46
MARATHON GENERATOR……………………………………………………….47
MECC ALTE GENERATOR…….………………………………………………...48
KOHLER CONTROL PANEL (NEW)..………...………………………………...49
AS3000 KOHLER CONTROL PANEL -AUSTRALIAN SPEC………………...50
KOHLER CONTROL PANEL (OLD)...………...………………………………...51
CAT CONTROL PANEL (NEW).………………...……………………………….52
AS3000 CAT CONTROL PANEL-AUSTRALIAN SPEC…….………………...53
CAT CONTROL PANEL (OLD).………………....……………………………….54
KUBOTA KEYED CONTROL PANEL (NEW)…………….…………………….55
AS3000 KUBOTA KEYED CONTROL PANEL-AUSTRALIAN SPEC ……....56
KUBOTA KEYED CONTROL PANEL (OLD).…………….…………………….57
KUBOTA DEEP SEA CONTROL PANEL (NEW) .………...…….……………..58
CE SPEC KUBOTA DEEP SEA CONTROL PANEL………………….………..59
KUBOTA DEEP SEA CONTROL PANEL (OLD).………...…….…..…………..60
LSC CONTROL PANEL…………………………………………………………..61
CONTROL BOX (NEW)………….………………………………………………..62
LSC CONTROL BRACKET……………………………………………………….63
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
5
NIGHT LITE PRO II 9/13/2011
LSC PHOTO CELL AND COMPONENTS………………………………………..64
OUTLET PANEL (OLD).…….…………..……………...……..…………………...65
OUTLET BOX MOUNT (OLD)………………..………...……..…………………..66
FUEL TANK….…….……………………………………..………………………….67
RIGHT INNER FENDER (NEW LAYDOWN)….……….………………………...68
RIGHT INNER FENDER (NEW VERTICAL)……………...……………………...69
RIGHT INNER FENDER (OLD LAYDOWN)………...…………………………...70
LEFT INNER FENDER (NEW LAYDOWN)...………..….……………………….71
LEFT INNER FENDER (NEW VERTICAL)…...………………………………….72
LEFT INNER FENDER (OLD LAYDOWN)……………...……………………….73
REAR PANEL…………...………………………..……….………………………...74
AS3000 REAR PANEL-AUSTRALIAN SPEC ….………………………………..75
LAYDOWN TOWER STRINGER ……….……..………..………………………...76
REAR TOWER SUPPORT………………………..…………………….………….77
VERTICAL TOWER STRINGER ………...………………………………………..78
LIFT BAR…………………….…….…….…………………………………………..79
LEFT DOOR………...………………………………..……………………….…….80
INSIDE LEFT DOOR VIEW VERTICAL TOWER……….…...………….………81
INSIDE LEFT DOOR VIEW LAYDOWN TOWER ……...……………………….82
RIGHT DOOR…...….………….…………………..………………………………..83
SOUND ATTENUATION PACKAGE (OPTION)…………………………………84
BATTERY………………………………………………..…………………………...85
MARKER LIGHTS………………………………………..………………………….86
AS3000 TAIL LIGHTS-AUSTRALIAN SPEC …………………………………….87
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
6
NIGHT LITE PRO II 9/13/2011
1000W SHO LAMP
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
7
NIGHT LITE PRO II 9/13/2011
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
8
NIGHT LITE PRO II 9/13/2011
1250W SHO LAMP
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
9
NIGHT LITE PRO II 9/13/2011
SHO LAMP HOLDER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
10
NIGHT LITE PRO II 9/13/2011
610250 - - LAMPHOLDER ASSY W/ YOKE W/ LAMP (610211) QD LEAD 650144 - - LAMPHOLDER ASSY W/ YOKE W/ LAMP (610211) NO LEAD 610265 - - LAMPHOLDER ASSY W/ YOKE W/ LAMP (610218) QD LEAD 610263 - - LAMPHOLDER ASSY W/ YOKE W/ LAMP (610218) NO LEAD 100632 - - LAMPHOLDER ASSY W/ YOKE W/ LAMP (610221) QD LEAD 100633 - - LAMPHOLDER ASSY W/ YOKE W/ LAMP (610221) NO LEAD
SHO LAMP ASSEMBLIES
LIGHT BAR MANUAL WINCH TOWER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
11
NIGHT LITE PRO II 9/13/2011
2 5/8 ROUND & 3” MANUAL WINCH TOWER SECTIONS
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
12
NIGHT LITE PRO II 9/13/2011
4” TOWER SECTION MANUAL WINCH TOWER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
13
NIGHT LITE PRO II 9/13/2011
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
14
NIGHT LITE PRO II 9/13/2011
3/16 X 11’ REMOVE THE CUSHION CLAMPS AND MAST WIRING FROM 3” MAST SECTION. REMOVE THE WIRE ROPE CLIPS AT TOP END OF THE 4” MAST SECTION. REMOVE THE 3” PULLEY AT THE END OF THE 3” MAST SECTION. REMOVE THE 2 5/8” ROUND MAST SECTION. REMOVE ALL THE BROKEN AND FRAYED CABLE. REPLACE NEW CABLE THROUGH SLOT AND EYELET IN THE ROUND MAST SECTION. REPLACE 2 5/8” ROUND MAST SECTION IN THE 3” MAST SECTION. ROUTE CABLE THROUGH PULLEY AND BRACKETS AND INSTALL 3” PULLEY. WITH ALL SECTIONS PUSHED TOGETHER TIGHT, INSERT CABLE THROUGH HALF-LINK AND INSTALL WIRE ROPE CLIPS. REINSTALL CUSHION CLAMPS AND MAST WIRING ON THE 3” MAST SECTION. 3/16 X 17’ 9” REMOVE MAST WIRING FROM BALLAST COMPARTMENT.(SEE ELECTRICAL SCHEMATIC) REMOVE THE CUSHION CLAMPS AND MAST WIRING FROM 4” MAST SECTION. REMOVE STOP BOLT AND WASHER. REMOVE 4 TOWER PADS AND 3” PULLEY AT THE END OF THE 4” MAST SECTION. REMOVE THE 2 5/8” ROUND AND THE 3” MAST SECTIONS TOGETHER. REMOVE ALL THE BROKEN AND FRAYED CABLE. REPLACE NEW CABLE THROUGH SLOT AND EYELET IN THE 3” MAST SECTION AND THROUGH PULLEY BRACKETS. REPLACE 2 5/8” ROUND AND 3” MAST SECTIONS. REPLACE 3” PULLEY AND TOWER PADS. ATTACH CABLE TO WINCH AND WIND IN A CLOCKWISE DIRECTION UNTILL ALL SLACK IS OUT. REPLACE STOP BOLT AND WASHER. REPLACE CUSHION CLAMPS AND MAST WIRING ON 4” MAST SECTION. REPLACE MAST WIRING IN BALLAST COMPARTMENT.(SEE ELECTRICAL SECHEMATIC) 3/16 X 10’ REMOVE ALL BROKEN AND FRAYED CABLE. FEED NEW CABLE THROUGH EYELET IN MAST PIVOT SECTION. FEED THROUGH PULLEY BRACKETS AND AROUND PULLEY IN FRONT UPRIGHTS. ATTACH CABLE TO WINCH AND WIND IN A CLOCKWISE DIRECTION UNTILL ALL SLACK IS OUT.
NS REQ'D PART NO DESCRIPTION2 620084 WIRE ROPE CLIP 3/16"1 045040 WIRE ROPE THIMBLE 1/4"1 620076 STEEL CABLE 3/16 X 11'1 650133 STEEL CABLE 3/16 X 17'9"1 320185 STEEL CABLE 3/16 X 10'
MANUAL LAYDOWN TOWER WINCH ONLY
INSTRUCTIONS FOR REPLACING STEEL CABLES
NEW PIVOT SECTION MANUAL WINCH TOWER (NEW)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
15
NIGHT LITE PRO II 9/13/2011
PIVOT SECTION MANUAL WINCH TOWER (OLD)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
16
NIGHT LITE PRO II 9/13/2011
PEDESTAL MANUAL WINCH TOWER (NEW)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
17
NIGHT LITE PRO II 9/13/2011
PEDESTAL MANUAL WINCH TOWER (OLD)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
18
NIGHT LITE PRO II 9/13/2011
MANUAL WINCH - NON CONTAINMENT TRAY
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
19
NIGHT LITE PRO II 9/13/2011
MANUAL WINCH - CONTAINMENT TRAY
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
20
NIGHT LITE PRO II 9/13/2011
ROTATIONAL LIGHT BAR VERTICAL TOWER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
21
NIGHT LITE PRO II 9/13/2011
SECTION 6 VERTICAL TOWER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
22
NIGHT LITE PRO II 9/13/2011
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
23
NIGHT LITE PRO II 9/13/2011
SECTION 5 VERTICAL TOWER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
24
NIGHT LITE PRO II 9/13/2011
SECTION 4 VERTICAL TOWER
SECTION 3 VERTICAL TOWER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
25
NIGHT LITE PRO II 9/13/2011
SECTION 2 VERTICAL TOWER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
26
NIGHT LITE PRO II 9/13/2011
SECTION 1 VERTICAL TOWER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
27
NIGHT LITE PRO II 9/13/2011
INSTRUCTIONS FOR REPLACING STEEL CABLES
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
28
NIGHT LITE PRO II 9/13/2011
HYDRAULIC VERTICAL TOWER Section 6 - Remove cable clamps (2) from section 4. Remove section 6. Remove all broken and frayed cable. Replace new cable into slot in the bottom of section 6. Replace section 6 into section 5. Route cable through pulley bracket on section5. With all sections pushed together tight, insert cable through half-link on section 5. Replace cable clips. Section 5 - Remove cable clamps (2) from section 3. Remove machine screws (8) and pads (4) from section 4. Being careful not to drop them into lower tower sections Remove section 5. Remove all broken and frayed cable. Replace new cable into slot in the bottom of section 5. Replace section 5 into section 4. Route cable through pulley bracket on section 4. With all sections pushed together tight, insert cable through half-link on section 3. Replace cable clips. Replace tower pads and screws. Be careful not to drop them into lower tower sections. Section 4 - Remove cable clamps (2) from section 2. Remove machine screws (8) and pads (4) from section 3. Being careful not to drop into lower tower sections Remove section 4. Remove all broken and frayed cable. Replace new cable into slot in the bottom of section 4. Replace section 4 into section 3. Route cable through pulley bracket on section 3. With all sections pushed together tight, insert cable through half-link on section 2. Replace cable clips. Replace tower pads and screws. Be careful not to drop them into lower tower sections.
INSTRUCTIONS FOR REPLACING STEEL CABLES
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
29
NIGHT LITE PRO II 9/13/2011
HYDRAULIC VERTICAL TOWER Section 3 - Remove cable clamps (2) from section 1. Remove machine screws (8) and pads (4) from section 2. Being care full not to drop into lower tower sections Remove section 3. Remove all broken and frayed cable. Replace new cable into slot in the bottom of section 3. Replace section 3 into section 2. Route cable through pulley bracket on section2. With all sections pushed together tight, insert cable through half-link on section 1. Replace cable clips. Replace tower pads and screws. Be careful not to drop them into lower tower sections. Note: If broken cable, tower pads or pad screw happen to fall into lower sections they must be retrieved . Damage to tower sections or other moving parts may occur. Note: When replacing tower section cables, the tower sections above the cable being replaced should be removed.
NYCOIL VERTICAL TOWER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
30
NIGHT LITE PRO II 9/13/2011
VERTICAL TOWER PEDESTAL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
31
NIGHT LITE PRO II 9/13/2011
VERTICAL TOWER HYDRAULIC PUMP
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
32
NIGHT LITE PRO II 9/13/2011
1250W - 60Hz BALLAST
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
33
NIGHT LITE PRO II 9/13/2011
1000W - 60 Hz (HPS) BALLAST
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
34
NIGHT LITE PRO II 9/13/2011
1000W - 50Hz BALLAST
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
35
NIGHT LITE PRO II 9/13/2011
AXLE
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
36
NIGHT LITE PRO II 9/13/2011
NOTE: NOT USED WITH CE SPEC.
FRAME
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
37
NIGHT LITE PRO II 9/13/2011
CE SPEC FRAME
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
38
NIGHT LITE PRO II 9/13/2011
TONGUE
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
39
NIGHT LITE PRO II 9/13/2011
NOTE: NOT USED WITH CE SPEC.
OUTRIGGERS
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
40
NIGHT LITE PRO II 9/13/2011
CONTAINMENT TRAY
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
41
NIGHT LITE PRO II 9/13/2011
ENGINE RAILS NON CONTAINMENT TRAY
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
42
NIGHT LITE PRO II 9/13/2011
CONTAINMENT TRAY ENGINE PAN
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
43
NIGHT LITE PRO II 9/13/2011
KOHLER ENGINE
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
44
NIGHT LITE PRO II 9/13/2011
CAT ENGINE
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
45
NIGHT LITE PRO II 9/13/2011
KUBOTA ENGINE
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
46
NIGHT LITE PRO II 9/13/2011
MARATHON GENERATOR
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
47
NIGHT LITE PRO II 9/13/2011
NOTE: ON SOME MODELS A 102692 ATHALON GENERATOR MAY BE USED INSTEAD OF THE 101075 MARATHON GENERATOR.
MECC ALTE GENERATOR
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
48
NIGHT LITE PRO II 9/13/2011
KOHLER CONTROL PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
49
NIGHT LITE PRO II 9/13/2011
AUSTRALIAN SPEC ONLY AS3000 KOHLER CONTROL PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
50
NIGHT LITE PRO II 9/13/2011
KOHLER CONTROL PANEL (Old Style)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
51
NIGHT LITE PRO II 9/13/2011
CAT 1.1 CONTROL PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
52
NIGHT LITE PRO II 9/13/2011
AUSTRALIAN SPEC ONLY AS3000 CAT 1.1 CONTROL PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
53
NIGHT LITE PRO II 9/13/2011
CAT CONTROL PANEL (Old Style)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
54
NIGHT LITE PRO II 9/13/2011
KUBOTA CONTROL PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
55
NIGHT LITE PRO II 9/13/2011
AUSTRALIAN SPEC ONLY AS3000 KUBOTA CONTROL PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
56
NIGHT LITE PRO II 9/13/2011
KUBOTA CONTROL PANEL (Old Style)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
57
NIGHT LITE PRO II 9/13/2011
KUBOTA DEEP SEA CONTROL PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
58
NIGHT LITE PRO II 9/13/2011
CE SPEC KUBOTA DEEP SEA CONTROL PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
59
NIGHT LITE PRO II 9/13/2011
KUBOTA DEEP SEA CONTROL PANEL (Old Style)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
60
NIGHT LITE PRO II 9/13/2011
LSC CONTROL PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
61
NIGHT LITE PRO II 9/13/2011
CONTROL BOX
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
62
NIGHT LITE PRO II 9/13/2011
LSC CONTROL BRACKET
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
63
NIGHT LITE PRO II 9/13/2011
LSC PHOTO CELL & COMPONENTS
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
64
NIGHT LITE PRO II 9/13/2011
OUTLET PANEL (Old Style)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
65
NIGHT LITE PRO II 9/13/2011
OUTLET BOX MOUNT (Old Style)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
66
NIGHT LITE PRO II 9/13/2011
FUEL TANK
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
67
NIGHT LITE PRO II 9/13/2011
NOTE: PLATE AND MOUNTING HARDWARE USED ONLY IN NON-CONTAINMENT TRAILERS.
RIGHT FENDER MOUNT (Laydown tower)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
68
NIGHT LITE PRO II 9/13/2011
RIGHT INNER FENDER (Vertical Tower)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
69
NIGHT LITE PRO II 9/13/2011
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
70
NIGHT LITE PRO II 9/13/2011
RIGHT INNER FENDER (Old Style Laydown Tower)
LEFT INNER FENDER (Laydown Tower)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
71
NIGHT LITE PRO II 9/13/2011
LEFT INNER FENDER (Vertical Tower)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
72
NIGHT LITE PRO II 9/13/2011
LEFT FENDER MOUNT (Old Style Laydown Tower)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
73
NIGHT LITE PRO II 9/13/2011
REAR PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
74
NIGHT LITE PRO II 9/13/2011
AUSTRALIAN SPEC ONLY AS3000 REAR PANEL
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
75
NIGHT LITE PRO II 9/13/2011
LAYDOWN TOWER STRINGER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
76
NIGHT LITE PRO II 9/13/2011
REAR TOWER SUPPORT
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
77
NIGHT LITE PRO II 9/13/2011
VERTICAL TOWER STRINGER
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
78
NIGHT LITE PRO II 9/13/2011
NOTE: 310033 IS USED WITH 16/8 TOWER CORD 310032 IS USED WITH 14/7 TOWER CORD
LIFT BAR
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
79
NIGHT LITE PRO II 9/13/2011
LEFT DOOR
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
80
NIGHT LITE PRO II 9/13/2011
INSIDE LEFT DOOR Vertical Tower
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
81
NIGHT LITE PRO II 9/13/2011
INSIDE LEFT DOOR Laydown Tower
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
82
NIGHT LITE PRO II 9/13/2011
RIGHT DOOR
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
83
NIGHT LITE PRO II 9/13/2011
SOUND ATTENUATION PACKAGE (OPTION)
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
84
NIGHT LITE PRO II 9/13/2011
BATTERY
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
85
NIGHT LITE PRO II 9/13/2011
MARKER LIGHTS
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
86
NIGHT LITE PRO II 9/13/2011
AUSTRALIAN SPEC ONLY AS3000 TAIL LIGHTS
NOTE: NS = NOT SHOWN. WHEN ORDERING, SPECIFY THE COLOR WANTED ON PARTS CONTAINING THE LETTER “P”
87
NIGHT LITE PRO II 9/13/2011
top related