manhole covers and gratings - 2pr · pdf file4 mufl e manhole covers and gratings are...
Post on 06-Mar-2018
229 Views
Preview:
TRANSCRIPT
3
Ductile cast iron is a ferrous alloy with a carbon content higher than 2% approximately, either loose as graphite or as iron carbide Fe3C (cementite). The former is called Grey Iron and the latter White Iron. While grey iron is to be preferred to make manhole covers and gratings, white iron is very fragile and hard, so it is not suitable to make utensils.
Grey iron can be either lamellar or ductile cast iron.
Lamellar cast iron is made up of thousands of plates which interrupt the continuity of the metal matrix and consequently jeopardise its mechanical resistance and make it subject to possible cracking or braking.
Ductile cast iron is is made up of spheroids achieved by introducing a suitable quantity of magnesium into the bath before the casting. This gives the product a high breaking load as well as remarkable elasticity.
A comparison between lamellar cast iron and ductile cast iron shows that:
• ductile cast iron has a higher breakage safety coefficient, since it follows any deformation due to loads without breaking (unlike lamellar cast iron), then returning to the original condition after the stress;
• to manufacture a product in lamellar cast iron with the same load class as a ductile cast-iron product, you need more mass. So the product will be heavier with higher shipment and handling costs.
Ductile cast iron is therefore a very valuable building material: it has as many benefits as lamellar cast iron but it does not have some of its defects. Its mechanical characteristics are similar to those of good-quality steel.
Ductile cast iron MANHOLE COVERS AND GRATINGS
LAMELLAR CAST IRON
DUCTILE CAST IRON
4
Mufl e manhole covers and gratings are manufactured in offi cially ISO9001-certifi ed factories located in China with ductile cast iron GJS 500-7 (Standard EN 1563-2004). They are designed according to Standard EN124 based on ISO 9001:2000 procedures, which certify the quality system of the product/service supplied by Mufl e.
Class A15 Area which can only be used by pedestrians and pedal cyclists.
Class B125 Footways, pedestrian areas and comparable areas, car parks or parking decks.
Class C250 For gratings installed in the area of kerbside channels of roads which, when measured from the kerb edge, extend maximum 0.5 m into the carriageway and maximum 0.2 m into the footway.
Class D400Arriageways of roads (pedestrian streets included), hard shoulders and parking areas for all types of road vehicles.
Class E600 Areas subject to high axle loads such as docks and airports.
Class F900 Areas subject to very high axle loads such as airports.
MANHOLE COVERS AND GRATINGS
EXCERPT FROM STANDARD EN124Manhole covers and gratings for pedestrian and vehicular traffi c. Manufacturing principles, type tests, marks, quality control.
4. Classifi cation Manhole covers and gratings are divided into the following classes:A15, B125, C250, D400, E600, F900.
EN 124
LOAD CLASSES
5
6. Materials6.1. General6.1.1. Manhole covers and gratingsThe manhole covers and gratings (gratings excluded) are manufactured in the following materials:a. lamellar cast ironb. ductile cast ironc. steel castingsd. rolled steele. one of materials a) b) c) d) combined with concretef. reinforced concrete (plain concrete excluded)Rolled steel can be used only if a suitable protection against corrosion is ensured. The type of corrosion required against corrosion will be agreed upon by the customer and supplier.6.1.2 The gratings must be manufactured in:a. lamellar cast ironb. ductile cast ironc. steel castingsThe filling of the covers can be made of concrete or other suitable materials.
8. TestsThe manhole covers and gratings must be tested as complete units in operating conditions. Compliance with the load requirements of the relevant Class must be determined by a load test.
9. MarksAll manhole covers, gratings and frames must have a legible durable mark showing: a. EN 124 (reference to the Standard)b. the relevant class (e.g. D400) or relevant classes for the products used for several classes (e.g. D400 – E600)c. the name and/or identification mark of the
manufacturer and the place of production - which can be expressed as a code
d. certifier’s mark. The following information may be shown too:
e. additional marks about the application or ownerf. product identification (name and/or number of
catalogue)
Said marks must be clearly and durably shown. They should be visible when the unit is installed, if possible.
Load tests in Mufl e’s in-house laboratory
EXPLANATORY DIAGRAM OF THE LOAD CLASSES
6
Certifi cations MANHOLE COVERS AND GRATINGS
QUALITY ASSURANCE CERTIFICATES ISO 9001
The concept of quality in a company must be intended as the “ability to meet the needs of all the stakeholders involved in the processes of production/supply and use of products and services”. The customers and/or users, workers, owners and shareholders, suppliers and the community in general are consequently concerned based on the Company’s strategies.
In 2001 MUFLE S.p.A. was awarded the Certifi cate of Compliance with Standard ISO 9001:2000 by the Italian Quality Assurance Institute IGQ No°2B45 for its “design, manufacture and commercial distribution of drainage systems, manhole covers and gratings marked MUFLE
– Commercial distribution of products for the building industry”.This means that all the Company’s processes from the management of resources to the manufacture of the products - including the defi nition of responsibilities, the analysis and improvement of the processes - are handled systematically and regularly. And they are aimed to meet the customer’s requests and to ensure consistency in the quality of the goods manufactured.
7
IGQ PRODUCT CERTIFICATES
The manhole covers and gratings in ductile cast iron manufactured by MUFLE S.p.A. are certifi ed according to Standard EN 124 “Manhole covers and gratings”.
The certifi cate is a further guarantee for the fi nal customer that the products are manufactured with high-quality manufacturing processes and comply with the reference specifi cations. This also ensures that the regular checks specifi ed by Standard EN 124 are carried out, as MUFLE S.p.A continuously performs load tests in its in-house laboratory as well as metallographic analyses and tensile tests in external laboratories.
Consequently all MUFLE manhole covers and gratings are marked with the IGQ symbol.
A15
MQAxx
MUFLE
UNI EN 124 A15EN-GJS-500/7
A
A
H
L
9
• Square inspection manhole cover made of ductile cast iron GJS-500-7 according to EN 1563
• Class A15 in compliance with EN 124 - Pedestrian Areas -
• Bituminous paint coating
• Frame design compatible with standard and non-standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Frame shaped to stop smells and for improved watertightness
• Sliding frame along special grooves that can be easily lifted too
• Cover with anti-slippery surface
• Cover equipped with special spaces to house the marks specified by Standard EN 124
• Plastic identification plugs can be provided for
• Product certification by independent certifier IGQ
590001 200 140 20 2,00 162 6,00
590002 300 200 30 5,50 162 18,00
590003 400 300 30 8,50 100 27,00
590004 500 400 35 12,50 100 39,00
590005 600 500 35 19,00 100 57,00
590006 700 600 40 29,20 20 87,00
Code Size (mm) Weight (Kg) Package Price (€)
AxA LxL H - Frame
Series AlfaDUCTILE CAST-IRON HYDRAULIC MANHOLE COVERS
L1
B
A
MRB6080
MUFLE
UNI EN 124 B125 EN-GJS-500/7
H
L2
B125
10
• Square or rectangular inspection manhole cover made of ductile cast iron GJS-500-7 according to EN 1563
• Class B125 in compliance with EN 124 - Hard shoulders and parking areas -
• Bituminous paint coating
• Frame design compatible with standard and non- standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Frame shaped to stop smells and for improved watertightness
• Sliding frame along special grooves that can be easily lifted too
• Cover with anti-slippery surface
• Cover equipped with special spaces to house the marks specified by Standard EN 124
• Plastic identification plugs can be provided for
• Product certification by independent certifier IGQ
Series Beta
590108 800x600 700x500 37 33,20 20 97,65
DUCTILE CAST-IRON HYDRAULIC MANHOLE COVERS
RECTANGULAR MANHOLE COVER
Code Size (mm) Weight (Kg) Package Price (€)
AxB L1xL2 H - Frame
MQBxx
MUFLE
UNI EN 124 B125 EN-GJS-500/7
A
A
H
LB125
11
590100 300 200 27 6,50 200 18,12
590101 400 300 27 10,00 100 25,88
590102 500 400 32 17,00 100 44,00
590107 550 450 37 21,00 40 54,35
590103 600 500 32 26,00 40 67,29
590104 700 600 37 37,00 40 95,76
590106 800 700 37 47,00 15 121,65
Series Beta
SQUARE MANHOLE COVER
Code Size (mm) Weight (Kg) Package Price (€)
AxA LxL H - Frame
L2
H
L1
A
B
C250
12
• Square or rectangular inspection manhole cover made of ductile cast iron GJS-500-7 according to EN 1563
• Class C250 in compliance with EN 124 - Pavement kerb -
• Bituminous paint coating
• Frame design compatible with standard and non- standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Frame shaped to stop smells and for improved watertightness
• The cover can be lifted by means of special hooks
• Cover with anti-slippery surface
• Cover equipped with special spaces to house the marks specified by Standard EN 124
• Plastic identification plugs can be provided for
• Product certification by independent certifier IGQ
Series Gamma
590208 800x600 700x500 50 45,1 20 132,35
590209 900x700 800x600 55 61,8 15 182,35
DUCTILE CAST-IRON HYDRAULIC MANHOLE COVERS
RECTANGULAR MANHOLE COVER
Code Size (mm) Weight (Kg) Package Price (€)
AxB L1xL2 H - Frame
C250A
A
H
LMQCxx
MUFLE
UNI EN 124 C250EN-GJS-500/7
13
590200 300 200 32 7,00 200 21,00
590201 400 300 32 13,50 100 36,24
590202 500 400 37 22,30 60 56,94
590203 550 450 37 26,80 60 69,88
590204 600 500 42 32,30 60 82,82
590205 700 600 52 45,00 15 116,47
590206 800 700 56 61,00 10 157,88
590210 900 800 67 90,00 10 264,71
590211 1000 900 72 110,00 5 323,53
Series Gamma
SQUARE MANHOLE COVER
Code Size (mm) Weight (Kg) Package Price (€)
AxA LxL H - Frame
L1
MRD6080
MUFLE
UNI EN 124 D400 EN-GJS-500/7
A
B
H
L2
D400
14
• Square or rectangular inspection manhole cover made of ductile cast iron GJS-500-7 according to EN 1563
• Class D400 in compliance with EN 124 - Carriageways of roads -
• Bituminous paint coating
• Frame design compatible with standard and non- standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Frame shaped to stop smells and for improved watertightness
• Cover with anti-slippery surface
• The cover and frame can be lifted by means of special hooks
• Cover equipped with special spaces to house the marks specified by Standard EN 124
• Plastic identification plugs can be provided for
• Product certification by independent certifier IGQ
Series Delta
590409 800x600 700x500 100 59,00 8 161,38
DUCTILE CAST-IRON HYDRAULIC MANHOLE COVERS
RECTANGULAR MANHOLE COVER
Code Size (mm) Weight (Kg) Package Price (€)
AxB L1xL2 H - Frame
L
H
A
A
EN-GJS-500/7UNI EN 124 D400
MUFLE
MQDxx
D400
15
590400 400 300 100 20,00 52 51,76
590401 500 400 100 32,00 36 82,82
590405 550 450 100 47,00 36 121,65
590402 600 500 100 46,00 32 119,06
590403 700 600 100 64,00 8 165,65
590404 800 700 100 82,00 8 212,24
590406 900 800 100 135,00 8 369,26
590407 1000 900 100 175,00 5 478,68
590408 1100 1000 100 202,00 6 552,53
Series Delta
SQUARE MANHOLE COVER
Code Size (mm) Weight (Kg) Package Price (€)
AxA LxL H - Frame
D400
A
H
L
16
DUCTILE CAST-IRON HYDRAULIC MANHOLE COVERSSeries Omega
• Inspection manhole cover with access hole ø600 in ductile cast iron GJS-500-7 according to EN 1563
• Class D400 in compliance with EN 124 - Carriageways of roads -
• Bituminous paint coating
• Frame design compatible with standard and non- standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Round/Square/Octagonal frame with anti-noise and anti-smell polyethylene gasket
• Cover with anti-slippery surface
• Round cover with hinge for maximum opening 110°
• Cover equipped with special spaces to house the marks specified by Standard EN 124
• Closing system by mechanical locking. Two appendixes fixed inside the cover lock it in the frame thanks to the mechanical properties of ductile cast iron. The high elasticity makes it possible to move the appendixes. When they are pushed or subject to a “lever effect”, they get locked (or released) against the relevant anchoring element in the frame.
• Also available with the words “Aqueduct” or “Sewer” upon request
• Product certification by independent certifier IGQ
590500 --- 750 ø600 100 59,00 10 152,71590504 Sewer 750 ø600 100 59,00 10 152,71590508 Aqueduct 750 ø600 100 59,00 10 152,71
MANHOLE COVER WITH SQUARE BASE 750x750
Code Marking Size (mm) Weight (Kg) Package Price (€)
AxA L H - Frame
A H
L
A H
L
D400
D400
D400
A H
L
17
Series Omega
MANHOLE COVER WITH SQUARE BASE 850x850
MANHOLE COVER WITH ROUND BASE Ø 850
MANHOLE COVER WITH OCTAGONAL BASE 850
590502 --- ø850 ø600 100 60,00 10 155,29590506 Sewer ø850 ø600 100 60,00 10 155,29590510 Aqueduct ø850 ø600 100 60,00 10 155,29
590501 --- 850 ø600 100 63,00 10 163,06590505 Sewer 850 ø600 100 63,00 10 163,06590509 Aqueduct 850 ø600 100 63,00 10 163,06
590503 --- 850 ø600 100 58,00 10 150,12590507 Sewer 850 ø600 100 58,00 10 150,12590511 Aqueduct 850 ø600 100 58,00 10 150,12
Code Marking Size (mm) Weight (Kg) Package Price (€)
AxA L H - Frame
Code Marking Size (mm) Weight (Kg) Package Price (€)
A L H - Frame
Code Marking Size (mm) Weight (Kg) Package Price (€)
AxA L H - Frame
B
A
L2
L1
H
D400
18
DUCTILE CAST-IRON MANHOLE COVERS FOR TELECOMMUNICATIONS NETWORKS AND ELECTRIC ENERGY
• Developed to allow the operators to access underground networks easily and safely
• Rectangular inspection manhole cover made of ductile cast iron GJS-500-7 according to EN 1563
• Class D400 in compliance with EN 124 - Carriageways of roads -
• Bituminous paint coating
• Frame size compatible with standard gullies used for telecommunications networks
• Frame equipped with slots to lift the manhole cover by special hooks
• Frame with support base and width suitable to reduce the weights on the gully below
• Cover with anti-slippery surface
• Cover equipped with special spaces to house the marks specified by Standard EN 124
• Cover made up of several triangular sections hinged to the frame. 90° is enough to make them safe for the operator. Maximum opening 110°
• Thanks to the special handles which can be inserted in the holes in the cover, it can be lifted easily
• The steadiness of the cover is ensured on the 3-point support
• Customised mark with the operator’s name upon request
590921 770x670 650x580 100 88,00 16 336,47
590922 770x1465 600x1200 100 180,00 8 688,24
Series Eta
ELECTRIC ENERGY MANHOLE COVER
Code Size (mm) Weight (Kg) Package Price (€)
AxB L1xL2 H - Frame
B L 1
HA
L2
D400
19
590513 770x670 650x580 100 88,00 16 336,47
590514 770x1465 600x1200 100 180,00 8 688,24
Series Eta
590926 0,4 5,29
KEY
Code Weight (kg) Price (€)
TELECOMMUNICATIONS MANHOLE COVER
Code Size (mm) Weight (Kg) Package Price (€)
AxB L1xL2 H - Frame
UNI EN 124 C250
MUFLE MQRCxx
A
A PL
H
C250
20
• Square inspection manhole cover made of ductile cast iron GJS-500-7 according to EN 1563
• Class C250 in compliance with EN 124 - Pavement kerb -
• Bituminous paint coating
• Frame design compatible with standard and non- standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Frame with anti-noise gasket
• Filling up to 75 mm with concrete or other materials suitable for pavings/pavements
• The cover can be lifted by means of special hooks which can be used after filling too
• Cover equipped with special spaces to house the marks specified by Standard EN 124
• Product certification by independent certifier IGQ
590303 400 300 95 75 26,00 20 71,12
590300 500 400 95 75 42,20 18 114,88
590301 600 500 95 75 57,70 16 158,65
590302 700 600 95 75 75,90 8 207,88
Series Kappa DUCTILE CAST-IRON FILLING MANHOLE COVERS
Code Size (mm) P - Filling Weight (Kg) Package Price (€)
AxA LxL H - Frame
L
H
A
A
32MGRCxx
EN-GJS-500/7UNI EN 124 C250
MUFLE
C250
22
DUCTILE CAST-IRON FLAT GRATINGS
Series Lambda
• Square flat grating made of ductile cast iron GJS-500-7 according to EN 1563
• Class C250 in compliance with EN 124 - Pavement kerb -
• Bituminous paint coating
• Frame design compatible with standard and non- standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Possibility of siphon
• Grating with anti-slippery surface
• Grating equipped with special spaces to house the marks specified by Standard EN 124
• Uniform arrangement of the slots on the whole surface of the grating. The slots are oriented perpendicularly and longitudinally to the driving direction. Size according to EN 124
• Product certification by independent certifier IGQ
590700 300 190 45 7,00 220,00 160 21,00
590701 400 290 45 13,00 520,00 100 33,65
590702 500 390 45 23,00 730,00 50 59,53
590703 550 440 45 28,00 730,00 50 72,47
590704 600 490 45 31,00 1200,00 30 80,24
590705 700 590 45 43,00 1740,00 24 111,29
Code Size (mm) Weight (Kg) Drainage Package Price (€)
AxA LxL H - Frame surface (cm²)
L
H
A
A
EN-GJS-500/7UNI EN 124 C250
MUFLE
32MGRCxxC
C250
23
590800 300 190 52,5 9,00 225 140 23,29
590801 400 290 57,5 15,00 520 100 38,82
590802 500 390 62,5 26,00 730 50 67,29
590803 550 440 62,5 31,40 730 50 80,24
590804 600 490 67,5 36,00 1200 30 93,18
590805 700 590 72,5 48,00 1700 24 124,24
• Square concave grating made of ductile cast iron GJS-500-7 according to EN 1563
• Class C250 in compliance with EN 124 - Pavement kerb -
• Bituminous paint coating
• New frame design compatible with standard and non- standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Possibility of siphon
• Grating with anti-slippery surface
• Grating equipped with special spaces to house the marks specified by Standard EN 124
• Uniform arrangement of the slots on the whole surface of the grating. The slots are oriented perpendicularly and longitudinally to the driving direction. Size according to EN 124
• Product certification by independent certifier IGQ
Series Sigma DUCTILE CAST-IRON CONCAVE GRATINGS
Code Size (mm) Weight (Kg) Drainage Package Price (€)
AxA LxL H - Frame surface (cm²)
32MGRC50C
MUFLEUNI EN124 C250
EN-GJS-500/7
A
A
L
H
C250
24
590812 400 290 57,5 16,00 460,00 60 43,76
590813 500 390 62,5 25,00 760,00 48 68,38
590814 600 490 67 35,40 1260,00 30 96,83
• Square concave grating made of ductile cast iron GJS-500-7 according to EN 1563
• Class C250 in compliance with EN 124 - Pavement kerb -
• Bituminous paint coating
• New frame design compatible with standard and non-standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Possibility of siphon
• Grating with anti-slippery surface
• Grating equipped with special spaces to house the marks specified by Standard EN 124
• Square slots defined “HONEYCOMB” slots arranged on the whole surface of the grating. Size according to EN 124
• Product certification by independent certifier IGQ
Series Sigma DUCTILE CAST-IRON CONCAVE GRATINGS
Code Size (mm) Weight (Kg) Drainage Package Price (€)
AxA LxL H - Frame surface (cm²)
PA
L
AH
MUFLE
EN-GJS-500/7UNI EN 124 D400
32MGRD60A
D400
25
DUCTILE CAST-IRON FLAT GRATINGS WITH HINGES
590809 500 390 100 35,00 460,00 36 95,74
590810 600 490 100 46,00 760,00 32 125,82
590811 700 590 100 59,00 1260,00 8 161,38
• Square flat grating with hinges made of ductile cast iron GJS-500-7 according to EN 1563
• Class D400 in compliance with EN 124 - Carriageways of roads -
• Bituminous paint coating
• New frame design compatible with standard and non-standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• The frame is equipped with special slides in the walls where the pins fixed to the cover can slide
• The frame is equipped with stops that make sure the open grating stays steady
• Grating with anti-slippery surface
• A “HINGE” device makes the articulation of the grating on the frame possible. The movement of the pins along the slides in the frame makes sure that:
- opening is easy and safe
- the grating cannot be taken away or tampered with, as it is not removable
• Grating equipped with special spaces to house the marks specified by Standard EN 124
• Uniform arrangement of the slots on the whole surface of the grating. The slots are oriented perpendicularly and longitudinally to the driving direction. Size according to EN 124
• Possibility of siphon
• Size of the slots according to UNI EN 124 to make sure no dangers are posed to cyclists
• Product certification by independent certifier IGQ
Series Epsilon
mit Scharnier
REGISTERED
PATENT
with hinge
Code Size (mm) Weight (Kg) Drainage Package Price (€)
AxA LxL H - Frame surface (cm²)
A
H
L
D400
26
DUCTILE CAST-IRON FLAT GRATINGSSeries Omega
• Grating with 600ø access hole in ductile cast iron GJS-500-7 according to EN 1563
• Class D400 in compliance with EN 124 - Carriageways of roads -
• Bituminous paint coating
• Frame design compatible with standard and non-standard gullies
• Frame with support base and width suitable to reduce the weights on the gully below
• Round/Square/Octagonal frame with anti-noise and anti-smell polyethylene gasket
• Grating with anti-slippery surface
• Round grating with hinge for maximum opening 110°
• Grating equipped with special spaces to house the marks specified by Standard EN 124
• Uniform arrangement of the slots on the whole surface of the grating. The slots are oriented perpendicularly and longitudinally to the driving direction. Size according to EN 124
• Closing system by mechanical locking. Two appendixes fixed inside the grating lock it in the frame thanks to the mechanical properties of ductile cast iron. The high elasticity makes it possible to move the appendixes. When they are pushed or subject to a “lever effect”, they get locked (or released) against the relevant anchoring element in the frame.
• Product certification by independent certifier IGQ
590600 750 Ø600 100 59,00 1125,00 10 177,00
GRATING WITH SQUARE BASE 750x750
Code Size (mm) Weight (Kg) Drainage Package Price (€)
AxA L H - Frame surface (cm²)
A H
L
A H
L
D400
D400
D400
A H
L
27
Series Omega
GRATING WITH SQUARE BASE 850x850
GRATING WITH ROUND BASE Ø 850
GRATING WITH OCTAGONAL BASE 850
590603 850 Ø600 100 57,00 1125,00 10 171,00
590602 Ø850 Ø600 100 61,00 1125,00 10 183,00
590601 850 Ø600 100 65,00 1125,00 10 195,00
Code Size (mm) Weight (Kg) Drainage Package Price (€)
AxA L H - Frame surface (cm²)
Code Size (mm) Weight (Kg) Drainage Package Price (€)
A L H - Frame surface (cm²)
Code Size (mm) Weight (Kg) Drainage Package Price (€)
AxA L H - Frame surface (cm²)
P
29
SQUARE SIPHON FOR FLAT AND CONCAVE GRATINGS MADE OF DUCTILECAST-IRON
590900 590700 590800 87,00 5,40 100 20,65
590901 590701 590801 590812 87,00 8,00 60 30,59
590902 590702 590802 590813 590809 87,00 15,20 32 57,35
590903 590703 590803 87,00 22,00 32 84,12
590904 590704 590804 590814 590810 87,00 20,30 30 76,47
590905 590705 590805 590811 87,00 29,60 30 110,88
Code Suitable for code Depth P (mm) Weight (kg) Package Price (€)
• Siphon GJS-500-7 according to EN1563
• Siphon made up of two elements fitting into each other that can be combined with all Mufle gratings - both flat and concave - except for the Omega gratings
• It prevents stones, leaves and other foreign bodies from falling into and clogging the piping in the water drain system below
• It prevents bad smells from spreading and keeps rats away
• Bituminous paint coating
• It is not subject to any technical regulation
The listed functions are ensured as long as regular maintenance is carried out by removing any foreign bodies carried by rainwater into the bowl.
Series Zeta
AB
DE
HH
1
AB
H
H
DE
1
30
MANHOLE COVERS WITH SIPHONSeries Tau
DUCTILE CAST-IRON SQUARE FRAME
DUCTILE CAST-IRON ROUND FRAME
Code Size (mm) Drainage Weight (kg) Flow Price (€) Frame Grating Inner ø Outer ø Tot. height Height surface (cm²) L/s A B DN DE H H1
591006 ø150 ø132 40 48 85 30 25 2,00 0,8 43,50
591007 ø200 ø174 60 68 98 30 37 4,00 0,8 64,70
591008 ø250 ø224 80 89 130 40 70 7,30 1,0 107,43
591009 ø300 ø273 100 100 140 40 119 11,50 1,4 146,05
591010 ø350 ø300 150 160 150 45 137 15,80 4,0 219,30
591011 ø400 ø300 150 160 170 45 137 20,80 4,0 279,69
Code Size (mm) Drainage Weight (kg) Flow Price (€) Frame Grating Inner ø Outer ø Tot. height Height surface (cm²) L/s AxA B DN DE H H1
591000 150 ø132 40 48 85 30 25 2,20 0,8 47,16
591001 200 ø174 60 68 98 30 37 4,20 0,8 68,36
591002 250 ø224 80 89 130 40 70 7,70 1,0 110,33
591003 300 ø273 100 110 140 40 119 12,50 1,4 162,06
591004 350 ø300 150 160 150 45 137 17,80 4,0 248,12
591005 400 ø300 150 160 170 45 137 21,00 4,0 284,30
B
A
H
C250
32
DUCTILE CAST-IRON GRATINGS FOR CHANNELS WITH LONGITUDINAL MEMBERSeries Theta
Code Size (mm) Weight (Kg) Drainage Package Price (€) A B H surface (cm²)
590850 750 400 35 26,50 1420,00 20 101,32
590851 750 500 35 32,50 1990,00 20 124,26
590852 750 600 35 42,80 2350,00 30 163,65
• Gratings with longitudinal members for drainage channels cast in place
• Class C250 in compliance with EN 124 - Pavement kerb -
• Class D400 in compliance with EN 124 - Carriageways of roads -
• System made up of three elements: GRATINGS, LEFT LONGITUDINAL ELEMENT, RIGHT LONGITUDINAL ELEMENT
• Gratings made of ductile cast iron GJS-500-7 according to EN 1563
• Bituminous paint coating
• Uniform arrangement of the square slots on the whole surface of the grating. Size according to EN 124
• Gratings with anti-slippery surface
• Gratings equipped with special housings and a hole for fastening them to the longitudinal members
• The gratings bear all the marks specified by Standard EN 124
• The ductile cast-iron longitudinal members GJS-500-7 according to EN 1563 act as supports for the gratings
• The longitudinal members have pits for the concrete so that a single body is created with the structure below. The longitudinal members can be screwed to the base thanks to 3 fixing slots
• The longitudinal members have special holes where a 10 mm-diameter rod can be introduced for the casting
• The left longitudinal member has two fins which prevent the grating from moving and coming out during operation
• The right longitudinal member has a screw M10 made of stainless steel AISI 304 for fastening it to the grating
GRATINGS CLASS C 250
D400
D400C250
B
A
H
Longherone Dx
Longherone Sx
H
H1
H
H1
LA
LA
33
Code Size (mm) Weight (Kg) Package Price (€)A L H H1
590856 right 750 68 97 35 6,20 assembled with grating 23,71
590857 left 750 68 97 35 6,30 assembled with grating 27,79
Serie Theta
Size (mm)Code
A B H Weight (kg) Drainage surface (cm²) Package Price (€)
590853 750 400 35 30,50 1420,00 20 115,85
590854 750 500 35 41,00 1990,00 20 156,76
590855 750 600 35 51,00 2350,00 30 195,38
LONGITUDINAL MEMBERS
GRATINGS CLASS D 400
Right longitudinal member
Left longitudinal member
3
2
4
1
34
INSTALLATION OF SERIES THETA GRATINGSSeries Theta
ASSEMBLING CONSISTS IN 4 DIFFERENT STAGES:
1. Fasten the longitudinal members to the structure below;
2. Insert the grating so that the fi ns of the left longitudinal member (acting as a hinge) match the housings in the grating;
3. Rest the other side of the grating on the right longitudinal member: the screw will pass through the hole in the grating;
4. Screw a cap nut on the protruding screw: make sure an unremovable spring washer is inserted too.
35
InstallationINSTALLATION OF MANHOLE COVERSAND GRATINGS
For the appropriate use of a manhole cover or grating it is necessary to:
• have a load class suitable to the function and installation place. To this end the specifi cations of Standard EN124 must be considered (see par. 4 of this catalogue on page 4);
• carry out a perfect installation so that the other materials used will be able to house the loads due to pedestrian and/or vehicular traffi c and to withstand them properly.
The following recommendations are about the installation:
a. Use concrete with a minimum compression strength of Rck 35N/mm2 and stone aggregate with max granulometry 6/8 mm in compliance with the hardening times specifi ed.
b. Use units with a frame base designed so as to be dimensionally compatible with all the gullies (either standard or non-standard).
c. Use units whose frames have a supporting surface which guarantees compliance with max pressure value, i.e. 7.5 N/mm2 according to EN124. This requirement is guaranteed for certifi ed products. Warning: The frame must rest perfectly on the top of the gully to be sure that the pressure value is guaranteed.
d. Remove any foreign bodies from the frame and the gully before preparing a layer of cement mortar between them of about 2 cm.
e. Level the frame to ensure that, once the work has been completed, there are no uneven sections between the road surface and the unit level, as they cause traffi c troubles and in the long term can cause early aging of the manhole cover or grating.
f. Include a stiffening edge of at least 250/300 mm per side. Metal reinforcements can be used to properly counter the traction stress generated in the concrete support (in case of heavy loads during use).
g. According to the type of cement used for the installation and the climatic conditions in which the work is carried out (temperature, humidity level etc), comply with minimum hardening times before inserting the cover or the grating into the frame and before making the installation area suitable for transit. For ordinary cement types sold on the market said times are at least 1 hour for cover or grating insertion and 48/72 hours before transit is possible. In some case concrete additives can be used to speed up these times (quick setting cement).
h. Make sure there are no concrete residues or bituminous conglomerate between the cover and the frame in the hinge area or closing systems (if any), as they can jeopardise the steadiness of the cover and make it noisy.
36
ELEMENTS OF CONTRACT
1. Supply and installation of manhole cover or grating “SERIES ALFA” (Beta, Gamma, Delta) in ductile cast iron GJS 500/7 in compliance with EN 1563 and according to the designing, testing and marking requirements specifi ed by Standard EN 124, with load class A15 (B125, C250, D400), as made up of:
• Square fl at frame with outer dimensions at least ___mm, net open space at least ___mm and height at least __mm, equipped with anchoring and supporting devices having standardised dimensions for improved adhesion to cement mortar. The U shape inside makes it watertight.
• Square cover whose dimensions allow coupling with the relevant frame. Its fi tting depth is at least __mm and it comes equipped with stiffening ribs on the bottom which ensure resistance to loads, closed-bottom slots which house suitable lifting hooks, anti-slippery projecting elements whose surface is 10% to 70% the overall surface, and the marks specifi ed by the Standard.
2. Supply and installation of manhole cover or grating “SERIES BETA” (Gamma, Delta) in ductile cast iron GJS 500/7 in compliance with EN 1563 and according to the designing, testing and marking requirements specifi ed by Standard EN 124, with load class (B125, C250, D400), as made up of:
• Rectangular fl at frame with outer dimensions at least ___mm, net open space at least ___mm and height at least __mm, equipped with anchoring and supporting devices having standardised dimensions for improved adhesion to cement mortar. The U shape inside makes it possible to house the special ductile cast-iron siphon.
• Rectangular cover whose dimensions allow coupling with the relevant frame. Its fi tting depth is at least __mm and it comes equipped with stiffening ribs on the bottom which ensure resistance to loads, closed-bottom slots which house suitable lifting hooks, anti-slippery projecting elements whose surface is 10% to 70% the overall surface, and the marks specifi ed by the Standard.
3. Supply and installation of manhole cover or grating “SERIES KAPPA” in ductile cast iron GJS 500/7 in compliance with EN 1563 and according to the designing, testing and marking requirements specifi ed by Standard EN 124, with load class C250, as made up of:
• Square fl at frame with outer dimensions at least ___mm, net open space at least ___mm and height at least __mm, equipped with anchoring and supporting devices having standardised dimensions for improved adhesion to cement mortar, and a gasket which ensures steadiness.
• Square cover whose dimensions allow coupling with the relevant frame. Its fi tting depth is at least __mm and it comes equipped with stiffening ribs on the bottom which ensure resistance to loads, closed-bottom slots which house suitable lifting hooks, and a 75mm-deep fi lling tank which ensures any paving can be used.
4. Supply and installation of manhole cover or grating “SERIES OMEGA” in ductile cast iron GJS 500/7 in compliance with EN 1563 and according to the designing, testing and marking requirements specifi ed by Standard EN 124, with load class D400, as made up of:
• Square (round, octagonal) fl at frame with outer dimensions at least ___mm, net open space at least ___mm and height at least __mm, equipped with anchoring and supporting devices having standardised dimensions for improved adhesion to cement mortar. It has an internal U shape which makes it watertight and an anti-smell/anti-movement shaped gasket which counters the cover edge. The frame must also have one groove suitable to house the hinge used to open the cover so that the cover can be locked in the open position at 110° and one groove for releasing and opening said cover.
• Round cover (grating) whose dimensions allow coupling with the relevant frame. Its fi tting depth is at least __mm and it comes equipped with stiffening ribs on the bottom which ensure resistance to loads, one appendix for frame releasing and one appendix for frame articulation, anti-slippery projecting elements whose surface is 10% to 70% the overall surface, and the marks specifi ed by the Standard. Closing is ensured by a suitable elastic bar.
5. Supply and installation of manhole cover or grating “SERIES ETA” (telecommunications networks and electric energy) in ductile cast iron GJS 500/7 in compliance with EN 1563 and according to the designing, testing and marking requirements specifi ed by Standard EN 124, with load class D400, as made up of:
• Rectangular fl at frame with outer dimensions at least ___ mm, net open space at least ___mm and height at least 100mm, equipped with anchoring and supporting devices having standardised dimensions for improved adhesion to cement mortar. The U shape inside makes it watertight. The frame must also have 4 or 8 slots (uniformly arranged on the two parallel sides) to house the relevant hinges to open the cover. A locking system in the open position at 110° and a safe position already at 90° will be provided for.
• Cover made up of 2 or 4 triangular sections whose dimensions allow coupling with the relevant frame. Each section is fi xed to it by means of 2 hinges. Its fi tting depth is at least __mm and it comes equipped with stiffening ribs on the bottom which ensure resistance to loads, anti-slippery projecting elements whose surface is 10% to 70% the overall surface, the marks specifi ed by the Standard, and a mark identifying the telecommunications network (electric energy) in order to determine a unique installation place.
6. Supply and installation of manhole cover or grating “SERIES LAMBDA” (Sigma, Sigma B) in ductile cast iron GJS 500/7 in compliance with EN 1563 and according to the designing, testing and marking requirements specifi ed by Standard EN 124, with load class C250 as made up of:
• Square fl at (concave) frame with outer dimensions at least ___mm, net open space at least ___mm and height at least __mm, equipped with anchoring and supporting devices having standardised dimensions for improved adhesion to cement mortar. The U shape inside makes it possible to house the special ductile cast-iron siphon.
• Square fl at (concave) grating whose dimensions allow coupling with the relevant frame. Its fi tting depth is at least __mm and it comes equipped with stiffening ribs on the bottom which ensure resistance to loads, concentric pseudo-rectangular slots with rounded corners (square slots uniformly arranged on the whole surface, usually defi ned “honeycomb” slots), anti-slippery projecting elements whose surface is 10% to 70% the overall surface, and the marks specifi ed by the Standard.
7. Supply and installation of manhole cover or grating with hinge “SERIES EPSILON” in ductile cast iron GJS 500/7 in compliance with EN 1563 and according to the designing, testing and marking requirements specifi ed by Standard EN 124, with load class D400, as made up of:
• Square fl at frame with outer dimensions at least ___mm, net open space at least ___mm and height at least __mm, equipped with anchoring and supporting devices having standardised dimensions for improved adhesion to cement mortar. The U shape inside makes it possible to house the special ductile cast-iron siphon. The frame must also have an articulating system for the grating housed inside which prevents the grating from being tampered with. Stops are provided to lock the grating in the open position at 125°.
• Square fl at cover whose dimensions allow coupling with the relevant frame. Its fi tting depth is at least 50mm and it comes equipped with stiffening ribs on the bottom which ensure resistance to loads, concentric pseudo-rectangular slots with rounded corners, anti-slippery projecting elements whose surface is 10% to 70% the overall surface, and the marks specifi ed by the Standard.
8. Supply and installation of gratings for drainage channels “SERIES THETA” with longitudinal members in ductile cast iron GJS 500/7 in compliance with EN 1563 and according to the designing, testing and marking requirements specifi ed by Standard EN 124, with load class C250 or D400, as made up of:
• Rectangular fl at grating with length at least 750mm, width at least ___mm and height at least 35mm, equipped with stiffening ribs on the bottom which ensure resistance to loads, square slots uniformly arranged on the whole surface, anti-slippery projecting elements whose surface is 10% to 70% the overall surface, and the marks specifi ed by the Standard. The grating must also have a hole for fastening with a screw and a nut on one side, and two slots to house the longitudinal-member fi ns on the other side in order to prevent any movements during operation.
• Right longitudinal member with length at least 750mm, width at least 68mm, height at least 97mm and fi tting depth at least 35mm. It must be equipped with a stainless-steel screw to fi x the grating, pits for the concrete support, holes to introduce a rod for the casting, and knurling on the bottom to ensure more adherence.
• Left longitudinal member with length at least 750mm, width at least 68mm, height at least 97mm and fi tting depth at least 35mm. It must be equipped with two protruding fi ns which (during the assembly operations) will be fi tted into special housings in the grating to prevent any movement during operation. It will also have pits for the concrete support, holes to introduce a rod for the casting, and knurling on the bottom to ensure more adherence.
Code Description Price (€) Q.tyCode Description Price (€) Q.ty
COPY FOR ORDERSName of Company Bank
Street/Road Agency
Postcode/City Abi
Fax Cab
VAT No. Payment terms
Destination of goods
Mufl e SpaVia S. Maria in Potenza, scn62017 Porto Recanati (MC)ITALYTel. +39 071 9799122Fax +39 071 7592275
info@mufl e.comwww.mufl e.com
1.Val
idity
The
cur
rent
pric
e lis
t can
cels
and
repl
aces
pre
vious
pric
e lis
ts.
2.O
rder
s Any
offe
r or o
rder
sha
ll alw
ays b
e ac
cept
ed o
nly a
fter t
he s
uppl
ier’s
con
fi rm
atio
n.
It sh
all b
e ac
cept
ed o
nly a
fter t
he S
elle
r’s
writ
ten
confi
rmat
ion
or w
ith th
e sh
ipm
ent
of th
e go
ods.
3.O
ffers
Our
writ
ten
or o
ral o
ffers
are
not
bi
ndin
g. T
he o
rder
s sha
ll be
cons
ider
ed
acce
pted
onl
y afte
r our
writ
ten
confi
rmat
ion.
4.D
elive
ry te
rms
The
deliv
ery h
as to
be
cons
ider
ed E
x-W
orks
Por
to R
ecan
ati (M
C).
Del
ivery
term
s are
give
n fo
r inf
orm
atio
n pu
rpos
es o
nly.
We
will
do o
ur b
est t
o m
eet
them
, but
any
late
del
ivery
sha
ll not
just
ify
neith
er c
ance
llatio
n of
the
orde
r nor
any
in
dem
nifi c
atio
n. T
he d
elive
ry te
rms c
ome
into
fo
rce
on th
e da
te o
f the
ord
er c
onfi r
mat
ion.
Ex
cept
for a
cts o
f God
suc
h as
stri
kes,
pow
er
failu
res e
tc, w
orkin
g da
ys a
re to
be
cons
ider
ed
for d
elive
ry te
rms.
5.Sh
ipm
ent T
he g
oods
, alth
ough
sol
d on
a
free-
to-d
estin
atio
n ba
sis in
com
plia
nce
with
sp
ecia
l agr
eem
ents
, are
alw
ays s
hipp
ed a
t th
e Pu
rcha
ser’s
com
plet
e ris
k. In
the
even
t of
any
dam
age
to th
e go
ods c
ause
d by
tra
nspo
rtatio
n, im
med
iate
not
ice
shal
l be
give
n on
rece
iving
the
good
s. T
he C
usto
mer
sha
ll
mak
e a
spec
ial n
ote
in th
e sh
ippi
ng d
ocum
ent
in o
rder
to d
escr
ibe
the
type
and
qua
ntity
of
prod
ucts
that
got
dam
aged
.6.
Pric
es E
xcep
t for
agr
eem
ents
to th
e co
ntra
ry, t
he p
rices
in fo
rce
whe
n th
e go
ods
are
deliv
ered
or s
hipp
ed s
hall b
e ap
plie
d. T
he
pric
es in
this
Pric
e Li
st a
re q
uote
d w
ithou
t VAT
an
d sh
ipm
ent c
osts
.7.V
AT n
umbe
r and
tax
iden
tifi c
atio
n nu
mbe
r Th
e Pu
rcha
ser s
hall p
rovid
e co
rrect
tax
data
, it b
eing
und
erst
ood
that
the
Selle
r is f
ree
from
al
l res
pons
ibilit
y.8.
Paym
ents
All p
aym
ents
sha
ll be
settl
ed
on th
e ag
reed
dat
e di
rect
ly to
our
offi
ces
or th
roug
h du
ly au
thor
ised
peop
le. U
nles
s ot
herw
ise a
gree
d, p
aym
ents
sha
ll be
mad
e ei
ther
on
a ca
sh b
asis
whe
n th
e go
ods a
re
deliv
ered
or b
efor
e th
e sh
ipm
ent o
f the
goo
ds.
All p
aym
ents
are
due
acc
ordi
ng to
the
agre
ed
paym
ent t
erm
s, e
vent
in th
e ev
ent o
f late
de
liver
y, da
mag
e to
or p
artia
l/com
plet
e lo
ss o
f th
e go
ods d
urin
g sh
ipm
ent,
or if
the
deliv
ered
go
ods a
re a
t the
Pur
chas
er’s
disp
osal
and
the
Purc
hase
r has
not
col
lect
ed th
em. In
the
even
t of
late
pay
men
t, th
e le
gal in
tere
st ra
te s
hall
be a
pplic
able
. In th
e ev
ent o
f non
-pay
men
t, ho
wev
er, w
e re
serv
e th
e rig
ht to
issu
e a
draf
t on
dem
and,
with
cha
rges
, ten
day
s afte
r the
invo
ice
due
date
.9.T
itle re
tent
ion
Mufl
e re
tain
s ow
ners
hip
of th
e go
ods s
old
until
effe
ctive
pay
men
t is m
ade
in
full a
s agr
eed.
Mufl
e w
ill be
ent
itled
to re
scin
d th
e C
ontra
ct e
ven
if jus
t one
inst
alm
ent h
as
not b
een
settl
ed, e
xcep
t as p
rovid
ed fo
r in
Art.
1525
of C
.C. In
suc
h a
case
the
Purc
hase
r sh
all r
etur
n th
e go
ods p
urch
ased
and
sha
ll no
t be
entit
led
to a
ny re
imbu
rsem
ent f
or th
e in
stal
men
t alre
ady p
aid,
whi
ch w
ill be
kep
t as
com
pens
atio
n fo
r use
and
dam
age.
The
Se
ller a
lso re
serv
es th
e rig
ht to
exe
rcise
its
right
of r
ecou
rse
on th
e bu
ildin
g co
ntra
ctor
s if a
ny u
npai
d eq
uipm
ent o
r goo
ds h
ave
been
alre
ady u
sed.
10.C
laim
s and
com
plai
nts A
ny c
laim
s on
the
quan
tity,
type
and
qua
lity o
f the
goo
ds
supp
lied
mus
t be
sent
to th
e Se
ller w
ithin
8
days
from
the
Purc
hase
r’s re
ceip
t of t
he
good
s. N
o cl
aim
on
the
qual
ity o
f the
goo
ds
shal
l be
enfo
rced
, eve
n as
an
exce
ptio
n un
der
judi
cial
proc
eedi
ngs,
unl
ess
paym
ent f
or th
at
equi
pmen
t has
bee
n du
ly m
ade.
11.J
urisd
ictio
n In
the
even
t of a
disp
ute
the
Cou
rt of
Mac
erat
a ha
s sol
e co
mpe
tenc
e.12
.Effi
cacy
of t
he g
ener
al co
nditio
ns o
f sal
e Th
e Pu
rcha
ser,
in s
ubm
ittin
g th
e or
der,
who
lly
acce
pts t
hese
Gen
eral
Con
ditio
ns, w
hich
will
also
be
valid
for a
ny fu
rther
sup
ply m
ade
by
the
Selle
r to
said
Pur
chas
er. A
ny d
ecla
ratio
n m
ade
by e
mpl
oyee
s, a
gent
s etc
are
not
bi
ndin
g un
less
they
com
ply w
ith th
ese
Gen
eral
C
ondi
tions
. By a
ccep
ting
thes
e G
ener
al
Con
ditio
ns th
e Pu
rcha
ser w
aive
s its
ow
n ge
nera
l pur
chas
e co
nditio
ns.
Mufl
e S
.p.A
. res
erve
s the
righ
t to
chan
ge
tech
nica
l cha
ract
erist
ics,
mod
els a
nd p
rices
w
ithou
t prio
r not
ice.
GENE
RAL
COND
ITIO
NS O
F
SALE
590001 MANHOLE COVER ALFA A15- EN124 - Ext.200-Int.140-H 20 6,00
590002 MANHOLE COVER ALFA A15- EN124 - Ext.300-Int.200-H 30 18,00
590003 MANHOLE COVER ALFA A15- EN124 - Ext.400-Int.300-H 30 27,00
590004 MANHOLE COVER ALFA A15- EN124 - Ext.500-Int.400-H 35 39,00
590005 MANHOLE COVER ALFA A15- EN124 - Ext.600-Int.500-H 35 57,00
590006 MANHOLE COVER ALFA A15- EN124 T- Ext.700-Int.600-H 40 87,00
590100 MANHOLE COVER BETA B125- EN124 - Ext.300-Int.200-H 27 18,12
590101 MANHOLE COVER BETA B125- EN124 - Ext.400-Int.300-H 27 25,88
590102 MANHOLE COVER BETA B125- EN124 - Ext.500-Int.400-H 32 44,00
590103 MANHOLE COVER BETA B125- EN124 - Ext.600-Int.500-H 32 67,29
590104 MANHOLE COVER BETA B125- EN124 - Ext.700-Int.600-H 37 95,76
590106 MANHOLE COVER BETA B125- EN124 - Ext.800-Int.700-H 37 121,65
590107 MANHOLE COVER BETA B125- EN 124 - Ext.550-Int.450 -H 37 54,35
590108 MANHOLE COVER BETA B125 - EN 124 - Ext.800x600 - Int.700x500 - H 37 97,65
590200 MANHOLE COVER GAMMA C250- EN124 - Ext.300-Int.200-H 32 21,00
590201 MANHOLE COVER GAMMA C250- EN124 - Ext.400-Int.300-H 32 36,24
590202 MANHOLE COVER GAMMA C250- EN124 - Ext.500-Int.400-H 37 56,94
590203 MANHOLE COVER GAMMA C250- EN124 - Ext.550-Int.450-H 37 69,88
590204 MANHOLE COVER GAMMA C250- EN124 - Ext.600-Int.500-H 42 82,82
590205 MANHOLE COVER GAMMA C250- EN124 - Ext.700-Int.600-H 52 116,47
590206 MANHOLE COVER GAMMA C250- EN124 - Ext.800-Int.700-H 56 157,88
590208 MANHOLE COVER GAMMA C250-EN 124 - Ext. 800x600 Int.700x500 H50 132,35
590209 MANHOLE COVER GAMMA C250-EN 124 - Ext.900x700 Int.800x600 H55 182,35
590210 MANHOLE COVER GAMMA C250-EN 124 - Ext. 900 Int.800 H 67 264,71
590211 MANHOLE COVER GAMMA C250-EN 124 - Ext.1000 Int.900 H 72 323,53
590300 FILLING MANHOLE COVER KAPPA C250- EN124 - Ext.500-Int.400-H 95 114,88
590301 FILLING MANHOLE COVER KAPPA C250- EN124 - Ext.600-Int.500-H 95 158,65
590302 FILLING MANHOLE COVER KAPPA C250- EN124 - Ext.700-Int.600-H 95 207,88
590303 FILLING MANHOLE COVER KAPPA C250- EN124 - Ext.400-Int.300-H 95 71,12
590400 MANHOLE COVER DELTA D400- EN124 - Ext.400-Int.300-H 100 51,76
590401 MANHOLE COVER DELTA D400- EN124 - Ext.500-Int.400-H 100 82,82
590402 MANHOLE COVER DELTA D400- EN124 - Ext.600-Int.500-H 100 119,06
590403 MANHOLE COVER DELTA D400- EN124 - Ext.700-Int.600-H 100 165,65
590404 MANHOLE COVER DELTA D400- EN124 - Ext.800-Int.700-H 100 212,24
590405 MANHOLE COVER DELTA D400-EN 124 - Ext.550 -Int. 450 - H 100 121,65
590406 MANHOLE COVER DELTA D400-EN 124 - Ext.900 -Int. 800 -H 100 369,26
590407 MANHOLE COVER DELTA D400-EN 124 - Ext.1000 -Int. 900 -H 100 478,68
590408 MANHOLE COVER DELTA D400- EN 124- Ext.1100 -Int 1000 -H 100 552,53
590409 MANHOLE COVER DELTA D400- EN 124 - Ext.800x600 Int.700x500 -H 100 161,38
590500 MANHOLE COVER OMEGA D400- EN124 - Ext.750-Int.Ø 600-H 100 152,71
590501 MANHOLE COVER OMEGA D400- EN124 - Ext.850-Int.Ø 600-H 100 163,06
590502 MANHOLE COVER OMEGA D400- EN124 - Ext. Ø850-Int.Ø 600-H 100 155,29
590503 MANHOLE COVER OMEGA D400- EN124 - Ext.850-Int.Ø 600-H 100 150,12
590504 MANHOLE COVER OMEGA D400- EN124 - Ext.750-Int.Ø 600-H 100 SEWER 152,71
590505 MANHOLE COVER OMEGA D400- EN124 - Ext.850-Int.Ø 600-H 100 SEWER 163,06
590506 MANHOLE COVER OMEGA D400- EN124 - Ext. Ø850-Int.Ø600-H 100 SEWER 155,29
590507 MANHOLE COVER OMEGA D400- EN124 - Ext.850-Int.Ø 600-H 100 SEWER 150,12
590508 MANHOLE COVER OMEGA D400- EN124 - Ext.750-Int.Ø 600-H 100 AQUEDUCT 152,71
590509 MANHOLE COVER OMEGA D400- EN124 - Ext.850-Int.Ø 600-H 100 AQUEDUCT 163,06
590510 MANHOLE COVER OMEGA D400- EN124 - Ext. Ø850-Int.Ø 600-H 100 AQUEDUCT 155,29
590511 MANHOLE COVER OMEGA D400- EN124 - Ext.850-Int.Ø 600-H 100 AQUEDUCT 150,12
590513 MANHOLE COVER ETA D400- EN124 TELECOM. Ext.770x670-Int.650x580 2 Triangular 336,47
590514 MANHOLE COVER ETA D400- EN124 TELECOM. Ext. 770x1465-Int.600x1200 4 Triangular 688,24
590600 GRATING OMEGA D400- EN124 - Ext.750-Int. Ø600-H 100 177,00
590601 GRATING OMEGA D400- EN124 - Ext.850-Int. Ø600-H 100 195,00
590602 GRATING OMEGA D400- EN124 - Ext. Ø850-Int. Ø600-H 100 183,00
590603 GRATING OMEGA D400- EN124 - Ext. Ø850-Int. Ø600-H 100 171,00
590700 FLAT GRATING LAMBDA C250- EN124 - Ext.300-Int.190-H 45 21,00
590701 FLAT GRATING LAMBDA C250- EN124 - Ext.400-Int.290-H 45 33,65
590702 FLAT GRATING LAMBDA C250- EN124 - Ext.500-Int.390-H 45 59,53
590703 FLAT GRATING LAMBDA C250- EN124 - Ext.550-Int.440-H 45 72,47
590704 FLAT GRATING LAMBDA C250- EN124 - Ext.600-Int.490-H 45 80,24
590705 FLAT GRATING LAMBDA C250- EN124 - Ext.700-Int.590-H 45 111,29
590800 CONCAVE GRATING SIGMA C250- EN124 - Ext.300-Int.190-H 52,5 23,29
590801 CONCAVE GRATING SIGMA C250- EN124 - Ext.400-Int.290-H 57,5 38,82
590802 CONCAVE GRATING SIGMA C250- EN124 - Ext.500-Int.390-H 62,5 67,29
590803 CONCAVE GRATING SIGMA C250- EN124 - Ext.550-Int.440-H 62,5 80,24
590804 CONCAVE GRATING SIGMA C250- EN124 - Ext.600-Int.490-H 67,5 93,18
590805 CONCAVE GRATING SIGMA C250- EN124 - Ext.700-Int.590-H 72,5 124,24
590809 FLAT GRATING EPSILON D400- Ext.500 Int.390 H100 WITH HINGE 95,74
590810 FLAT GRATING EPSILON D400 - Ext.600 Int.490 H100 WITH HINGE 125,82
590811 FLAT GRATING EPSILON D400 - Ext.700 Int.590 H100 WITH HINGE 161,38
590812 CONCAVE GRATING SIGMA BEE C250- EN124 - Ext.400-Int.400 - H 57,5 43,76
590813 CONCAVE GRATING SIGMA BEE C250- EN124 - Ext.500-Int.500 - H 62,5 68,38
590814 CONCAVE GRATING SIGMA BEE C250- EN124 - Ext.600-Int.600 - H 67 96,83
590850 THETA CHANNEL GRATING C250-EN124 750x400 101,32
590851 THETA CHANNEL GRATING C250-EN124 750x500 124,26
590852 THETA CHANNEL GRATING C250-EN124 750x600 163,65
590853 THETA CHANNEL GRATING D400-EN124 750x400 115,85
590854 THETA CHANNEL GRATING D400-EN124 750x500 156,76
590855 THETA CHANNEL GRATING D400-EN124 750x600 195,38
590856 THETA LONGITUDINAL FRAME RIGHT C250 & D400 23,71
590857 THETA LONGITUDINAL FRAME LEFT C250 & D400 27,79
590900 SYPHONS ZETA FOR Ext.300 GRATINGS 20,65
590901 SYPHONS ZETA FOR Ext.400 GRATINGS 30,59
590902 SYPHONS ZETA FOR Ext.500 GRATINGS 57,35
590903 SYPHONS ZETA FOR Ext.550 GRATINGS 84,12
590904 SYPHONS ZETA FOR Ext.600 GRATINGS 76,47
590905 SYPHONS ZETA FOR Ext.700 GRATINGS 110,88
590921 MANHOLE COVER ETA D400- EN124 ENEL Ext.770x670-Int.650x580 2 Triangular 336,47
590922 MANHOLE COVER ETA D400- EN124 ENEL Ext.770x1465-Int.600x1200 4 Triangular 688,24
591000 SQUARE MANHOLE COVER WITH SIPHON TAU Ext.150 47,16
591001 SQUARE MANHOLE COVER WITH SIPHON TAU Ext.200 68,36
591002 SQUARE MANHOLE COVER WITH SIPHON TAU Ext.250 110,33
591003 SQUARE MANHOLE COVER WITH SIPHON TAU Ext.300 162,06
591004 SQUARE MANHOLE COVER WITH SIPHON TAU Ext.350 248,12
591005 SQUARE MANHOLE COVER WITH SIPHON TAU Ext.400 284,30
591006 ROUND MANHOLE COVER WITH SIPHON TAU Ext.Ø150 43,50
591007 ROUND MANHOLE COVER WITH SIPHON TAU Ext.Ø200 64,70
591008 ROUND MANHOLE COVER WITH SIPHON TAU Ext.Ø250 107,43
591009 ROUND MANHOLE COVER WITH SIPHON TAU Ext.Ø300 146,05
591010 ROUND MANHOLE COVER WITH SIPHON TAU Ext.Ø350 219,30
591011 ROUND MANHOLE COVER WITH SIPHON TAU Ext.Ø400 279,69
590926 KEY 5,29
LIGHT AND WATER CONVEYING SYSTEMS
Mufle SpaVia S. Maria in Potenza, scn 62017 Porto Recanati (MC)
ITALYTel. +39 071 9799122 Fax +39 071 7592275
info@mufle.comwww.mufle.com
ISO 9001:2000 Certifi ed Company
Non
-con
trac
tual
imag
es a
nd in
form
atio
n ca
n be
cha
nged
with
out p
rior n
otic
e.
Cod.
GH
_EN
_599
011
top related