lc-60le630u/u(a), lc-70le735u service manual...(s31o870le732u) service manual. outline...
Post on 09-Mar-2021
49 Views
Preview:
TRANSCRIPT
OUTLINE, MODIFIED PARTS AND MAJOR SERVICE PARTS
OUTLINE.............................................................iMODIFIED PARTS............................................. iiMAJOR SERVICE PARTS ................................ iii
CHAPTER 1. SPECIFICATIONS[1] SPECIFICATIONS
(LC-60LE630U/U(A))...................................... 1-1[2] SPECIFICATIONS (LC-70LE735U) ............... 1-2CHAPTER 2. OPERATION MANUAL[1] OPERATION MANUAL
(LC-60LE630U/U(A))...................................... 2-1[2] OPERATION MANUAL
(LC-70LE735U) .............................................. 2-6CHAPTER 3. REMOVING OF MAJOR PARTS[1] REMOVING OF MAJOR PARTS
(LC-60LE630U/U(A))...................................... 3-1
CHAPTER 4. ADJUSTMENT[1] ADJUSTMENT PROCEDURE
(LC-60LE630U/U(A)) .....................................4-1CHAPTER 5. TROUBLESHOOTING TABLE[1] TROUBLESHOOTING TABLE
(LC-60LE630U/U(A)) .....................................5-1CHAPTER 6. OVERALL WIRING/SYSTEM BLOCK DIAGRAM[1] OVERALL WIRING DIAGRAM
(LC-60LE630U/U(A)) .....................................6-1[2] OVERALL WIRING DIAGRAM
(LC-70LE735U) .............................................6-2[3] SYSTEM BLOCK DIAGRAM
(LC-60LE630U/U(A)) .....................................6-3[4] SYSTEM BLOCK DIAGRAM
(LC-70LE735U) .............................................6-4Parts Guide
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining thesafety and performance of the set.
SERVICE MANUAL
This document has been published to be used forafter sales service only.The contents are subject to change without notice.
CONTENTS
The new model can be identified with the following markings.
• As to the new service Parts, the mark A is printed on the model label.
LC-60LE630U
LC-60LE630U
No. S81S460LE630U
LCD COLOR TELEVISION
LC-60LE630U/U(A), LC-70LE735U
LC-60LE630ULC-60LE630U(A)LC-70LE735UMODELS
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-inal condition and only parts identical to those specified should be used.
This model is based on the LC-60LE632U/LC-70LE732U and partially modified.For the contents not covered in this Service Manual, accordingly, please refer to the LC-60LE632U/LC-70LE732U(S31O870LE732U) Service Manual.
OUTLINE
(LC-60LE630U(A))
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
i
LC60LE630U Service Manual
OUTLINE, MODIFIED PARTS AND MAJOR SERVICE PARTS
OUTLINEThis model is based on the LC-60LE632U/LC-70LE732U and partially modified.
For the contents not covered in this Service Manual, accordingly, please refer to the LC-60LE632U/LC-70LE732U (S31O870LE732U) Service Man-ual.
The following model label corresponds to this service manual.
The new model can be identified with the following markings.
• As to the new service Parts, the mark A is printed on the model label.
LC-60LE630U
LC-60LE630U
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
ii
MODIFIED PARTS
Ref. No. DescriptionLC-60LE632ULC-70LE732U
(S31O870LE732U)
LC-60LE630U/U(A)LC-70LE735U
(S81S460LE630U)Interchangeability Note
PRINTED WIRING BOARD ASSEMBLIESN MAIN Unit (LC-60LE630U/U(A)) DKEYMF733FM17 DUNTKF905FM01 D ChangedN MAIN Unit (LC-70LE735U) DKEYMF733FM19 DKEYMF733FM26 D ChangedN R/C OPC Unit DUNTKF494FM01 ← — No changedN ICON Unit (LC-60LE630U/U(A)) DUNTKF770FM02 ← — No changedN ICON Unit (LC-70LE735U) DUNTKF770FM02 DUNTKF770FM03 D ChangedN KEY Unit (LC-60LE630U/U(A)) DUNTKF800FM50 ← — No changedN KEY Unit (LC-70LE735U) DUNTKF800FM51 DUNTKF800FM50 D ChangedN WiFi Unit (LC-60LE630U/U(A)) RUNTKA810WJQZ — — DeleteN WiFi Unit (LC-70LE735U) RUNTKA810WJQZ ← — No changedN 3D IR EMITTER Unit (LC-70LE735U) — RUNTKA819WJQZ D AddN POWER/DRIVE Unit (LC-60LE630U/U(A)) RUNTKA847WJQZ ← — No changedN POWER Unit (LC-70LE735U) RUNTKA857WJQZ RDENCA442WJQZ D ChangedN LCD Control Unit (LC-60LE630U/U(A)) DUNTKF778FM02 RUNTK4911TPZT D ChangedN LCD Control Unit (LC-70LE735U) DUNTKF778FM04 RUNTK4909TPYP D ChangedN LED DRIVER Unit (LC-70LE735U) — RUNTKA842WJZZ D Add
LCD PANEL MODULE
N 60" LCD Panel Module Unit (LK600D3GW70Z) (LC-60LE630U) R1LK600D3GW70Z ← — No changed
N 60" LCD Panel Module Unit (LK600D3GW7AZ) (LC-60LE630U(A)) R1LK600D3GW70Z R1LK600D3GW7AZ D Changed
N 70" LCD Panel Module Unit (LK695D3GW20Z) (LC-70LE735U) R1LK695D3GW30Z R1LK695D3GW20Z D Changed
CABINET AND MECHANICAL PARTSPlease refer to a Parts Guide.
SUPPLIED ACCESSORIES/PACKING PARTS (NOT REPLACEMENT ITEM) Please refer to a Parts Guide.
SERVICE JIG (USE FOR SERVICING)Please refer to a Parts Guide.
Interchangeability
Completely interchangeableA: = NEWOLD
Interchangeable fromOLD to NEW
B: NEWOLD
Interchangeable fromNEW to OLD
C: NEW OLD
Not interchangeableD: X OLDNEW
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
iii
MAJOR SERVICE PARTS
PWB Unit(LC-60LE630U/U(A))
(LC-70LE735U)
NOTE: *1 Replace MAIN PWB Unit (DKEYMF733FM26) in case of IC8401, IC3303 or IC8455 failure.
OTHER Unit
IC For Exclusive Use Of The Service
Service Jigs
Ref No. Parts No. DescriptionN DUNTKF905FM01 MAIN UnitN DUNTKF494FM01 R/C, OPC UnitN DUNTKF770FM02 ICON UnitN DUNTKF800FM50 KEY UnitN RUNTKA847WJQZ POWER UnitN RUNTK4911TPZT LCD CONTROL Unit
Ref No. Parts No. DescriptionN DKEYMF733FM26 MAIN Unit (*1)N DUNTKF494FM01 R/C, OPC UnitN DUNTKF770FM03 ICON UnitN DUNTKF800FM50 KEY UnitN RUNTKA810WJQZ WiFi UnitN RUNTKA819WJQZ 3D IR EMITTER UnitN RDENCA442WJQZ POWER UnitN RUNTK4909TPYP LCD CONTROL UnitN RUNTKA842WJZZ LED DRIVER Unit
Ref No. Parts No. DescriptionN R1LK600D3GW70Z 60" LCD Panel Module Unit (LK600D3GW70Z) (LC-60LE630U)N R1LK600D3GW7AZ 60" LCD Panel Module Unit (LK600D3GW7AZ) (LC-60LE630U(A))N R1LK695D3GW20Z 70" LCD Panel Module Unit (LK695D3GW20Z) (LC-70LE735U)
Ref No. Parts No. Description Q'tyIC508 RH-iXD397WJQZS IC S-24CS02AFJ-TB-G (RGB) (LC-60LE630U/U(A)) 1
IC1503 RH-iXD394WJQZS IC S-24CS02AFJ-TB-G (HDMI1) (LC-60LE630U/U(A)) 1IC1504 RH-iXD396WJQZS IC S-24CS02AFJ-TB-G (HDMI3) (LC-60LE630U/U(A)) 1IC1505 RH-iXD395WJQZS IC S-24CS02AFJ-TB-G (HDMI2) (LC-60LE630U/U(A)) 1IC2001 RH-iXD241WJNBQ IC R5F21368CNFP (Monitor Microcomputer) (LC-70LE735U) 1
Ref No. Parts No. Description Q'tyN QCNW-C222WJQZ Connecting Cord L=1000mm 80pins, LCD Control Unit to LCD Panel Unit 2N QCNW-F676WJQZ Connecting Cord L=1000mm 41pins, MAIN Unit to LCD Control Unit (LW) 1N QCNW-M249WJQZ Connecting Cord L=1000mm, Main to LCD Control Unit (PD) (LC-60LE630U/U(A)) 1N QCNW-L214WJQZ Connecting Cord L=1000mm, 64pins, LCD Control Unit to LCD Panel Unit (LC-70LE735U) 2N QCNW-G405WJQZ Connecting Cord L=1000mm 4pins, POWER Unit to LCD Control Unit (PL) (LC-70LE735U) 1N QCNW-L795WJQZ Connecting Cord L=1000mm 24pins, MAIN Unit to POWER Unit (PD) (LC-70LE735U) 1N QCNW-L519WJQZ Connecting Cord L=1000mm 18pins, LED DRIVER Unit to POWER Unit (LA) (LC-70LE735U) 1
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
1 – 1
LC60LE630U Service Manual CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS (LC-60LE630U/U(A))
Item Model: LC-60LE630U/LC-60LE630U(A)
LCDpanel
Size 60" Class (601/32" Diagonal)
Resolution 2,073,600 pixels (1,920 1,080)
TVFunction
TV-standard (CCIR) American TV Standard ATSC/NTSC System
ReceivingChannel
VHF/UHF VHF 2-13ch, UHF 14-69ch
CATV 1-135ch (non-scrambled channel only)
Digital TerrestrialBroadcast (8VSB)
2-69ch
Digital cable*1
(64/256 QAM)1-135ch (non-scrambled channel only)
Audio multiplex BTSC System
Audio out 10W 2
Terminals
Rear
HDMI 1 HDMI in with HDCP, Audio in (ø 3.5 mm stereo minijack)
HDMI 2 HDMI in with HDCP
COMPONENT COMPONENT in
PC INANALOG RGB (PC) in (15-pin mini D-sub female connector),Audio in (ø 3.5 mm stereo minijack)
ANT/CABLE 75 Unbalance, F Type 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
AUDIO Audio in (ø 3.5 mm stereo minijack)
DIGITAL AUDIO OUTPUT Optical Digital audio output 1 (PCM/Dolby Digital)
OUTPUT Audio out
Side
HDMI 3 HDMI in with HDCP
VIDEO AV in
SERVICE Software update
OSD language English/French/Spanish
Power Requirement AC 120 V, 60 Hz
Power Consumption 180 W (0.2 W Standby with AC 120 V)
WeightTV + stand 71.7 lbs./32.5 kg
TV only 65.1 lbs./29.5 kg
Dimension*2
(W H D)
TV + stand 5429/64 34
19/64 13
1/8 inch
TV only 5429/64 33 2
27/32 inch
Operating temperature +32°F to +104°F (0°C to +40°C)
*1Emergency alert messages via Cable are unreceivable.
*2The dimensional drawings are shown on the Spanish operation manual.The width include the operation buttons.As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for productimprovement without prior notice. The performance specification figures indicated are nominal values of production units.There may be some deviations from these values in individual units.
Cautions regarding use in high and low temperature environmentsWhen the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.This is not a malfunction, and the unit will recover when the temperature returns to normal.Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near aheater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction.Storage temperature: -4°F to +140°F (-20°C to +60°C)
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
1 – 2
[2] SPECIFICATIONS (LC-70LE735U)
Item Model: LC-70LE735U
LCDpanel
Size 70" Class (691/2" Diagonal)
Resolution 2,073,600 pixels (1,920 1,080)
TVFunction
TV-standard (CCIR) American TV Standard ATSC/NTSC System
ReceivingChannel
VHF/UHF VHF 2-13ch, UHF 14-69ch
CATV 1-135ch (non-scrambled channel only)
Digital TerrestrialBroadcast (8VSB)
2-69ch
Digital cable*1
(64/256 QAM)1-135ch (non-scrambled channel only)
Audio multiplex BTSC System
Audio out 10W 2
Terminals
Back panelverticalinputs
HDMI 1 HDMI in with HDCP, Audio in (Ø 3.5 mm stereo jack)
HDMI 2 HDMI in with HDCP
HDMI 3 HDMI in with HDCP
HDMI 4 HDMI in with HDCP
AUDIO OUT Audio out (Ø 3.5 mm stereo jack)
USB 1 Photo/Music/Video mode, Software update
Back panelsurfaceinputs
COMPONENT COMPONENT in
VIDEO 1 AV in
VIDEO 2 AV in
PC INANALOG RGB (PC) in (15-pin mini D-sub female connector),Audio in (Ø 3.5 mm stereo jack)
RS-232C 9-pin D-sub male connector
Back panelhorizontalinputs
ANT/CABLE 75 Unbalance, F Type 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
AUDIO IN Audio in (Ø 3.5 mm stereo jack)
DIGITAL AUDIO OUTPUT Optical Digital audio output 1 (PCM/Dolby Digital)
ETHERNET Network connector
USB 2 Photo/Music/Video mode, Software update
OSD language English/French/Spanish
Power Requirement AC 120 V, 60 Hz
Power Consumption 252 W (0.1 W Standby with AC 120 V)
WeightTV + stand 99.2 lbs./45.0 kg
TV only 93.7 lbs./42.5 kg
Dimension*2
(W H D)
TV + stand 631/2 39
45/64 13
1/8 inch
TV only 631/2 38
25/64 3
1/2 inch
Operating temperature +32°F to +104°F (0°C to +40°C)
*1Emergency alert messages via Cable are unreceivable.
*2The dimensional drawings are shown on the inside back cover.As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes forproduct improvement without prior notice. The performance specification figures indicated are nominal values of productionunits. There may be some deviations from these values in individual units.
Cautions regarding use in high and low temperature environmentsWhen the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.This is not a malfunction, and the unit will recover when the temperature returns to normal.Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near aheater, as this may cause the cabinet to deform and the front panel to malfunction.Storage temperature: -4°F to +140°F (-20°C to +60°C)
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
2 – 1
LC60LE630U Service Manual CHAPTER 2. OPERATION MANUAL
[1] OPERATION MANUAL (LC-60LE630U/U(A))
Part Names
TV (Front)
Center Icon illumination Remote control sensor
* OPC: Optical Picture Control
OPC sensor *
TV (Rear/Side)
POWER button
MENU button
INPUT button
Channel buttons(CH / )
Volume buttons(VOL+/-)
SERVICE terminal
HDMI 3 terminal
VIDEO terminals
HDMI 1 terminal
Antenna/Cable in
HDMI 2 terminal
OUTPUT terminals
COMPONENT terminals
PC IN terminal
DIGITAL AUDIO OUTPUT terminal
AUDIO terminal(shared for HDMI 1 andPC IN) *3
*1
*1
*2
*1 External equipment connection.*2 Button operations.*3 PC Audio Select function.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
2 – 2
Direct Button Operation
Changing Volume
You can change the volume by pressing VOL+/- onthe TV or on the remote control unit.To increase the volume, press VOL+.To decrease the volume, press VOL-.
Audio status
Output deviceOutput Select
Fixed Variable
Speaker Variable sound Mute
When "Output Select" is set to "Variable", the indicator onthe screen changes as shown below.
Details on the Output Select function.
MUTE
Mutes the current sound output.Press MUTE." " will be displayed on the screen for 30 minutes, andthe sound is silenced.
Within 30 minutes of pressing MUTE, mute can becanceled by pressing VOL+/- or MUTE.Mute will be canceled after 30 minutes have passed.However, the TV will not suddenly output a loud sound asthe volume level is set to 0 automatically.
Sleep Timer
Allows you to set a time when the TV automaticallyswitches to standby.Press SLEEP.The remaining time displays when the sleep timer has been set.Each time you press SLEEP, the remaining time switchesas shown below.
Off 5 10 15 30 45
240 180 120 90 60
When set, the time automatically starts counting down.If you want to adjust the sleep timer, you can press SLEEPtwice then change the time setting.When it is 5 minutes before the time expires, the remainingtime will start to keep appearing every minute.
Select "Off" by pressing SLEEP to cancel the sleep timer.The TV will enter standby when the remaining time reaches 0.
FLASHBACK
Press FLASHBACK to switch to the previously tunedchannel.Press FLASHBACK again to switch back to the currentlytuned channel.
FLASHBACK will not work if no channel has been changedafter the TV is turned on.This function is available only when the input source is TV.
POWER
You can turn on the TV or put it on standby bypressing POWER on the TV or on the remote controlunit.
Changing Channels
You can change channels by pressing CH / or 0-9,(DOT).Examples:To select a 1 or 2-digit channel number (e.g., Channel 5):
Press5 ENT.
To select a 3-digit channel number (e.g., Channel 115):
Press1 1 5 ENT.
To select a 4-digit channel number (e.g., Channel 22.1):
Press2 2 (DOT) 1 ENT.
When selecting a 1-digit channel number, it is notnecessary to press 0 before the number.When you enter 0-9 only, channel selection will be made ifthere is no operation within a few seconds.If you push "0" by itself, nothing will happen.Complete the above steps within a few seconds.When you enter 0-9 and € (DOT), channel selection will bemade if there is no operation within a few seconds.
FAVORITE CH
You can select 4 preset favorite channels in 4 differentcategories.Press A,B,C or D.While watching the TV, you can toggle the selectedchannels by pressing A,B,C and D.
Details of favorite channel settings.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
2 – 3
AV MODE
AV Mode gives you several viewing options to choosefrom to best match the surrounding environment of theTV, which can vary due to factors like room brightness,type of program watched or the type of image inputfrom external equipment.
Press AV MODE. Current AV Mode displays.Press AV MODE again before the mode displayed on thescreen disappears. The mode changes as shown below:
Example:When the input source is TV, VIDEO or COMPONENTterminals
STANDARD MOVIE
STANDARD
STANDARD
MOVIE
GAME USER
DYNAMIC DYNAMIC (Fixed)
Example:
When the input source is HDMI 1, 2 or 3 terminals
GAME USER
PC DYNAMIC DYNAMIC (Fixed)
Example:When the input source is PC IN terminal
USER PC
STANDARD: For a highly defined image in a normal
lighting.
MOVIE: For a movie.
GAME: Lowers image brightness for easier viewing.
PC: For PC.
USER: Allows the user to customize settings as desired.
You can set the mode for each input source.
DYNAMIC (Fixed): Changes the image and sound
settings to the factory preset values. No adjustments
are allowed.
DYNAMIC: For a clear-cut image emphasizing high
contrast, useful for sports viewing.
You can select a different AV Mode item for each inputmode. (For example, select STANDARD for TV input andDYNAMIC for COMPONENT.)When you play games, "GAME" is recommended for AVMode.
PC
Allows you to gain quick access to PC mode.Press PC.
Operating On-Screen Display Menu
You can operate the on-screen display menu by usingthe following buttons.MENU: Displays the menu screen./ / / , ENTER: Select a desired item on the
screen.RETURN: Returns to the previous menu screen.EXIT: Turns off the menu screen.
For operating the on-screen display menu, see "MenuOperation Buttons".
Direct Button Operation
AUDIO
MTS/SAP stereo modeThe TV has a feature that allows reception of soundother than the main audio for the program. This featureis called Multi-channel Television Sound (MTS). The TVwith MTS can receive mono sound, stereo soundand Secondary Audio Programs (SAP). The SAPfeature allows a TV station to broadcast otherinformation, which could be audio in another languageor something completely different like weatherinformation.
You can enjoy Hi-Fi stereo sound or SAP broadcastswhere available.Stereo broadcasts: View programs like live sportingevents, shows and concerts in dynamic stereo sound.SAP broadcasts: Receive TV broadcasts in either MAIN orSAP sound. MAIN sound: The normal program soundtrack(either in mono or stereo). SAP sound: Listen to a secondlanguage, supplementary commentary or other information.(SAP is mono sound.)
If stereo sound is difficult to hear.
Obtain a clearer sound by manually switching to fixedmono-sound mode.
You can change MTS as shown below to match the televisionbroadcast signal.
Press AUDIO to toggle between audio modes.
Examples: when receiving MTS and SAPSTEREO mode: STEREO MONO
STEREO + SAP mode: STEREO SAP MONO
MONO mode: MONO
Digital broadcasting audio modeThe types of audio transmitted in a digital broadcast includeSURROUND as well as MONO and STEREO. In addition, itis possible for multiple audio tracks to accompany a singlevideo track.
1 PressAUDIO.A list of selectable audio is displayed.
2 Press / to select audio.
MTS only operates while in TV mode.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
2 – 4
Direct Button Operation
FREEZE
Allows you to capture and freeze a moving image thatyou are watching.Press FREEZE.A moving image is captured.Press FREEZE again to cancel the function.
When this function is not available, "No displaying stillimage available." will display.The still image automatically goes out after 30 minutes.If you are using the freeze function and a broadcastactivates the V-CHIP BLOCK, the freeze function will becanceled and a V-CHIP BLOCK message will appear.
INPUT
To view external source images, select the input source bypressing INPUT on the remote control unit or on the TV.
1 Press INPUT.A list of selectable sources appears.
2 Press INPUT again or press / to select theinput source.Each time INPUT is pressed, the input source toggles.
HDMI2 HDMI3
PC IN COMPONENT VIDEO
HDMI1
TV
An image from the selected source automatically displays.If the corresponding input is not plugged in, you cannot changethe input. Be sure to connect the equipment beforehand.
External equipment connection.Press PC to switch to an image from the PC.
DISPLAY
Displays channel information being viewed.Press DISPLAY.
Closed Captions and Digital Closed Captions
Your TV is equipped with an internal Closed Captiondecoder. It allows you to view conversations, narrationand sound effects as subtitles on your TV. ClosedCaptions are available on some TV programs and onsome VHS home video tapes at the discretion of theprogram provider.
Digital Closed Caption service is a new caption serviceavailable only on digital TV programs (also at thediscretion of the service provider). It is a more flexiblesystem than the original Closed Caption system,because it allows for a variety of caption sizes and fontstyles. When the Digital Closed Caption service is inuse, it will be indicated by the appearance of DTVCC.
Not all programs and VHS videotapes offer closedcaptions. Please look for the " " symbol to ensurethat captions will be shown.
In the Closed Caption system, there can be morethan one caption service provided. Each is identifiedby its own number. The "CC1", "CC2", "CC3" and"CC4" services display subtitles of TV programssuperimposed over the program's picture.
In the Closed Caption system, the TEXT1, TEXT2,TEXT3 or TEXT4 services display text that is unrelatedto the program being viewed (e.g., weather or news).These services are also superimposed over theprogram currently being viewed.
Press CC.On: Displays the closed caption.Off: Does not display the closed caption.
You can adjust the closed caption screen appearance toyour preference.
CC
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
2 – 5
Direct Button Operation
VIEW MODE
You can select the screen size.
Press VIEW MODE to toggle between view modes.
For HD programs
Stretch Dot by Dot (Full Screen) S.Stretch (Smart stretch) Zoom
Suitable for viewing wide-screen 1.78:1 aspect ratioprogram, stretch mode will stillshow very thin black bandsat the top and bottom of thescreen.
Dot by Dot (1080i/p only):Detects the resolution of thesignal and displays an imagewith the same number of pixelson the screen.Full Screen (720p only):You can select "Full Screen"only when receiving a 720psignal.
Suitable for stretching 4:3programs to fill the screen.
Suitable for viewing wide-screen 2.35:1 aspect-ratioprograms in full screen.
When using Dot by Dot or Full Screen, it is possible to see noise or bars around different outer portions of the screen. Pleasechange view mode to correct this.
For 4:3 programsExample: Screen size images
Side Bar S.Stretch (Smart stretch) Zoom Stretch
Suitable for viewingconventional 4:3 programs intheir normal format.
Suitable for stretching 4:3programs to fill the screen.
Suitable for viewing wide-screen 2.35:1 anamorphicDVDs in full screen.
This mode is useful for 1.78:1DVDs. When viewing 1.85:1DVDs, stretch mode will still showvery thin black bands at the topand bottom of the screen.
For PC input mode
Connect the PC before making adjustments.Selectable screen size may vary with input signal type.
Example: Screen size images
Normal Stretch Dot by Dot
Keeps the originalaspect ratio in a fullscreen display.
An image fully fills thescreen.
Detects the resolutionof the signal anddisplays an image withthe same number ofpixels on the screen.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
2 – 6
[2] OPERATION MANUAL (LC-70LE735U)
Part Names
TV (Front)
Center Icon illumination
Remote control sensor
*1 OPC: Optical Picture Control*2 This panel emits the infrared signal towards the 3D Glasses you wear when you view 3D images.Do not place anything between the 3D infrared emitter on the TV and the infrared receiver on the 3D Glasses.
3D infrared emitter *2
OPC sensor *1
TV (Rear/Side)
RS-232C terminal
Antenna/Cable in
POWERbutton
MENUbuttonINPUTbutton
Channelbuttons(CH / )
Volumebuttons(VOL+/-)
COMPONENTterminals
DIGITAL AUDIOOUTPUT terminal
HDMI 3 terminal
HDMI 4 terminal
HDMI 1 terminalARC: Audio Return Channel
VIDEO 2 terminals
VIDEO 1 terminals
AUDIO OUT terminal
USB 1 terminal
USB 2terminal
ETHERNETterminal
HDMI 2 terminal
PC IN terminal
*1*2
*1
*1
AUDIO IN terminal(shared for PC INand HDMI 1) *3
*1 External equipment connection.*2 Button operations.*3 Details on the Audio Select function.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
2 – 7
1
18
19
2021
4
3
2
5
2324
8
7
6
9
2526
28
29
15
14
13
121110
1617
27
22
1 POWER: Switch the TV power on or enter standby.
2 TV,STB,DVD VCR,AUDIO: Switches the remote
control for TV, STB, DVD, BD, VCR and AUDIO operation.
* To enter the code registration mode, you need to press
an appropriate button (STB,DVD VCR or AUDIO) and
DISPLAY at the same time.
3 External equipment operational buttons: Operate the
external equipment.
4 OPTION: Display the Link Operation Menu screen. This
button will function only when AQUOS LINK is used.
5 SLEEP: Set the sleep timer.
6 0-9: Set the channel.
7 (DOT)
8 CC: Display captions from a closed-caption source.
9 AV MODE: Select an audio or video setting.
10 MUTE: Mute the sound.
11 VOL+/-: Set the volume.
12 MENU: Display the menu screen.
13 3D: Select between 3D and 2D image viewing.
14 / / / , ENTER: Select a desired item on the screen.
15 EXIT: Turn off the menu screen.
16 FAVORITE CH: Set the favorite channels.
17 A, B, C, D: Select 4 preset favorite channels in 4 different
categories.
While watching, you can toggle the selected channels by
pressing A, B, C and D.
18 DISPLAY: Display the channel information.
19 POWER (SOURCE): Turns the power of the external
equipment on and off.
20 FREEZE: Set the still image. Press again to return to
normal screen.
21 POWER SAVING: Select Power Saving settings.
22 ENT: Jumps to a channel after selecting with the 0-9
buttons.
23 FLASHBACK: Return to the previous channel or external
input mode.
24 VIEW MODE: Select the screen size.
25 INPUT: Select a TV input source. (TV, HDMI1, HDMI2,
HDMI3, HDMI4, COMPONENT, VIDEO1, VIDEO2, PC IN,
Home Network (DLNA), USB)
26 CH / : Select the channel.
27 APPS: Display the application window.
28 RETURN: Return to the previous menu screen.
29 FAV APP 1, 2, 3: You can assign your favorite
applications to these buttons.
Remote Control Unit
When using the remote control unit, point it at the TV.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
3 – 1
LC60LE630U Service Manual CHAPTER 3. REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS (LC-60LE630U/U(A))
1. Removing of Stand Unit and Rear Cabinet.1. Remove the 4 lock screws and detach the Stand Unit .
2. Remove the 1 lock screw and detach the AC Cord Cover .
3. Disconnect AC wire and detach the AC Cord .
4. Remove the 4 VESA Hole Covers , 10 lock screws , 3 lock screws and 15 lock screws and detach the Rear Cabinet .
[Precaution when removing the rear cabinet]
If the rear cabinet is removed with the set upright, the speakers may fall; it results in connector disconnection. Therefore, never remove the rear cab-inet with the set upright.
Be sure to remove the rear cabinet with the screen side down.
[Precaution when mounting the rear cabinet]
Put the speakers in place with the screen side down, and attach the rear cabinet.
Since the speakers are fixed by the rear cabinet, they cannot be fixed without the rear cabinet.
2Stand Unit
Rear Cabinet10
4AC Cord Cover 5 AC Cord
VESA Hole Cover
8
9
7
6
3
1
[AC]
[AC]
Screws for fixing Speakerand Rear Cabinet
Speaker incline.Speaker fall down.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
3 – 2
[Precautions when fixing the Rear Cabinet]
When fixing the Rear Cabinet, be careful not to catch the backlight LED harness, speaker harness and other harnesses in it.
• The hooks on the external wall of the Rear Cabinet are fitted in the Front Cabinet Ass’y. After putting the Rear Cabinet in place, fit the hookssecurely; then tighten the screws.
(Work method of Rear Cabinet fixation)
(Front Cabinet Ass’y/Rear Cabinet fingernail fixation place)
Rear Cabinet(Mat parts)
Front Cabinet Ass'y(Luster parts)
There is a gap without the fingernail fitting in completely only when coveringwith Rear Cabinet.It becomes the factor of a gap increase of Front Cabinet Ass'y/Rear Cabinetand the Rear Cabinet misregistration.
Please tighten the screw after Rear Cabinet is firmly pushed, and thefingernail is confirmed.
17 places
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
3 – 3
2. Removing of Speaker (L/R), KEY Unit and Fixing Metal Angle.1. Detach the Bottom Cover
2. Disconnect the SP wire.
3. Detach the Speaker (L) , Speaker (R) .
4. Disconnect the RC wire.
5. Detach the KEY Unit Ass’y .
6. Disconnect the KM wire.
7. Remove the 2 lock screws and detach the Key Button from Key Button Cover .
8. Detach the KEY Unit from Key Button .
9. Remove the 19 lock screws and detach the Fixing Metal Angle .
2Speaker (L)3Speaker (R)
MAIN Unit
[SP] [RC]
[KM]
[SP]
7 5
4
8
6Key Button
10
9
FixingMetalAngle
1Bottom
Cover
KEY Unit
KEY Unit Ass'y
Key Button
Cover
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
3 – 4
3. Removing of Connectors1. Disconnect the following connectors from the MAIN Unit. (PD, LW, Cl)
2. Disconnect the following connectors from the POWER/DRIVE Unit. (PD, LA)
3. Disconnect the following connectors from the LCD CONTROL Unit. (LW, PL)
MAIN UnitPOWER/DRIVE Unit
LCD CONTROL Unit
MAIN Unit
[PD]
[CI]
[LW]
[LW]
[PD]
[PL]
[LA]
[LA]
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
3 – 5
4. Removing of 60” LCD Panel Module Unit, LCD CONTROL Unit, MAIN Unit, POWER/DRIVE Unit.1. Detach the 14 Fixing Metal Angles .
2. Remove the 8 Hooks and detach the 60” LCD Panel Module Unit .
3. Remove the 2 FFCs (80pin) , 2 Ferrite Cores and 6 lock screws and detach the LCD CONTROL Unit .
4. Remove the 2 lock screws and detach the Earth Angle .
5. Remove the 4 lock screws and detach the MAIN Unit and Terminal Angle (Side) .
6. Remove the 6 lock screws and detach the POWER/DRIVE Unit and AC Cord Barrier .
7. Remove the 16 lock screws and detach the 2 Center Angles .
60" LCD Panel
Module Unit
2
LCD CONTROL Unit6
16
Center
Angle
1Fixing Metal
Angle
4Ferrite Core
1 Fixing Metal
Angle
15
15
15 1516 Center
Angle
15
15
Hook
3 FFC (80pin)
Hook
1Fixing Metal
Angle
14AC Cord Barrier
1 Fixing Metal
Angle
1 Fixing Metal
Angle
13
POWER/DRIVE Unit
12
11Terminal Angle
(Side)
8Earth Angle
5
7
9
10
9
MAIN Unit
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
3 – 6
5. Removing of R/C OPC Unit, ICON Unit.1. Detach the R/C OPC Unit .
2. Disconnect the RA wire.
3. Remove the 1 lock screw and detach the ICON Unit .
4. Disconnect the CI wire.
Front Cabinet Ass'y
2
[CI]
3ICON Unit
[RA]
1R/C OPC Unit
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
4 – 1
LC60LE630U Service Manual CHAPTER 4. ADJUSTMENT
[1] ADJUSTMENT PROCEDURE (LC-60LE630U/U(A))The adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment isrequired due to part replacement, make an adjustment according to the following procedure.
1. After replacement of any PWB unit and/or IC for repair, please note the following.• When replacing the following units, make sure to prepare the new units loaded with updated software.
2. Upgrading of microprocessor softwareCAUTION: Never “POWER OFF” the unit when software upgrade is ongoing.
Otherwise the system may be damaged beyond recovery.
2.1. Software version upgradeThe model employs the following software.
• Main software
The main software can be upgraded by using a general-purpose USB Memory.
The followings are the procedures for upgrading.
2.2. Main software version upgrade
2.2.1 Get ready before you start• USB Memory of 128MB or higher capacity.
• PC running on Windows 98/98SE/ME/2000/XP operating system.
• USB Memory reader/writer or PC with a USB port.
• The file system of a USB memory is FAT. (FAT32 is not applied)
• Use the USB memory without other functions. (Lock and memory reader...etc)
2.2.2 PreparationsTo upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version upgrade.
1. Copy the file JAS_DTV_US_P101_Vx.xx_AP.BIN for version upgrade to the root directory (folder) of the USB Memory.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
Now the USB Memory for version upgrade is ready.
2.2.3 How to upgrade the software1. Unplug the AC cord.
2. Insert the USB Memory for version upgrade (prepared as above) into the service socket located Right side of Main Board terminals, upper HDMI3terminal.
3. Plug in the AC cord with power button pressed down after 5 seconds, releases the power button.
4. After a few seconds, EMBLEM LED will blink on and off.
No display on the LCD screen. (Black screen)
5. Upon completion of the upgrade process, EMBLEM LED will blink on and off quickly.
NOTE: If the EMBLEM LED doesn't come to blink on and off quickly within 70 seconds (ex. the unit was automatically rebooted on the way), theupgrade is failure.
• In the case of a failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.
6. Unplug the AC cord and remove the USB Memory for version upgrade.
7. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mainsoftware version information.
MAIN Unit: DUNTKF905FM01
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
4 – 2
3. Entering and exiting the adjustment process mode1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu.
2) While holding down the “VOL (–)” and “INPUT” keys at a time, plug in the AC cord of the main unit to turn on the power.
The letter “<K>” appears on the screen.
3) Next, hold down the “VOL (–)” and “CH ( )” keys at a time.
(The “VOL (–)” and “CH ( )” keys should be pressed and held until the display appears.)
Multiple lines of white characters appearing on the display indicate that the unit is now in the adjustment process mode.
When you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4) To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When thepower was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode. If thesettings are tampered in this mode, unrecoverable system damage may result.
4. Remote controller key operation in adjustment process mode
*Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
5. List of adjustment process mode menu
Remote controller key Main unit key FunctionCH ( / ) CH ( / ) Moving an item (line) by one (UP/DOWN)VOL (+/–) VOL (+/–) Changing a selected item setting (+1/ –1)Cursor (UP/DOWN) ————— Turing a page (PREVIOUS/NEXT)Cursor (LEFT/RIGHT) ————— Changing a selected line setting (+10/ –10)INPUT ————— Input switching (toggle switching)ENTER ————— Executing a function
Page Line Item Description Remarks1 1 Main Version Main software version BL: boot loader version
2 Check Sum Flash check sum3 PANEL Version4 TEMP SENSOR5 NORMAL STANDBY CAUSE Normal standby cause6 ERROR STANDBY CAUSE Error standby cause
2 1 Factory Init Initialization to factory settings2 Inch Setting Inch size3 Public Mode Public mode Not available4 Operation Acutime Accumulated operation time5 RESET Reset
3 1 RF-AGC ADJ Not available2 TUNER ADJ Not available3 PAL ADJ Not available4 RF AGC Not available5 TUNER Level Not available6 CVBS Level Not available7 VIF Not available8 VIDEO AGC Not available
4 1 COMP SD ADJ Component 15K picture level adjustment2 Y OFFSET3 Cb OFFSET4 Cr OFFSET5 Y GAIN6 Cb GAIN7 Cr GAIN8 RESET ADJUSTMENT Reset
5 1 COMP HD ADJ Component 33K picture level adjustment2 Y OFFSET3 Pb OFFSET4 Pr OFFSET5 Y GAIN6 Pb GAIN7 Pr GAIN8 RESET ADJUSTMENT Reset
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
4 – 3
6 1 RGB ADJ Analog RGB picture level adjustment2 G OFFSET3 B OFFSET4 R OFFSET5 G GAIN6 B GAIN7 R GAIN8 RESET ADJUSTMENT Reset
7 1 IN POINT LOW_D Adjustment point1 at Dynamic mode2 IN POINT HIGH_D Adjustment point2 at Dynamic mode3 R LEVEL LOW_D WB adjustment Point 1, R adjustment value at Dynamic mode4 G LEVEL LOW_D WB adjustment Point 1, G adjustment value at Dynamic mode5 B LEVEL LOW_D WB adjustment Point 1, B adjustment value at Dynamic mode6 R LEVEL HIGH_D WB adjustment Point 2, R adjustment value at Dynamic mode7 G LEVEL HIGH_D WB adjustment Point 2, G adjustment value at Dynamic mode8 B LEVEL HIGH_D WB adjustment Point 2, B adjustment value at Dynamic mode9 R LEVEL MAX_D WB adjustment Point Max., R adjustment value at Dynamic mode
10 G LEVEL MAX_D WB adjustment Point Max., G adjustment value at Dynamic mode11 B LEVEL MAX_D WB adjustment Point Max., B adjustment value at Dynamic mode
8 1 IN POINT LOW Adjustment point12 IN POINT HIGH Adjustment point23 R LEVEL LOW WB adjustment Point 1, R adjustment value4 G LEVEL LOW WB adjustment Point 1, G adjustment value5 B LEVEL LOW WB adjustment Point 1, B adjustment value6 R LEVEL HIGH WB adjustment Point 2, R adjustment value7 G LEVEL HIGH WB adjustment Point 2, G adjustment value8 B LEVEL HIGH WB adjustment Point 2, B adjustment value9 R LEVEL MAX WB adjustment Point Max., R adjustment value
10 G LEVEL MAX WB adjustment Point Max., G adjustment value11 B LEVEL MAX WB adjustment Point Max., B adjustment value12 ADJ DATA STORE Execute13 RESET ADJUSTMENT Reset
9 1 EEP CLEAR Clear all setting data of flash memory2 AUTO INSTALLATION SW3 STANDBY CAUSE RESET Reset STANDBY CAUSE4 DESTINATION Destination of factory Initialization5 L ERR RESET Number of termination due to lamp error and Reset6 L ERR STOP Stop the detection of amp error detection7 TEMP CAUTION Threshold level of temperature caution8 TEMP SHUTDOWN Threshold level of temperature protection
10 1 VCOM ADJ Not available2 TEST PATTERN Test pattern3 DIMMER DIMMER setting (64)
Page Line Item Description Remarks
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
4 – 4
6. Writing the microprocessor software
6.1. Writing the main microprocessor software and monitor microprocessor software (Main PWB: QPWBXF905WJZZ)
7. Signal adjustment
7.1. LCD section adjustment [LCD module adjustment]
7.2. Image adjustment
7.2.1 Device check
Before adjustment, check that the adjustment jig and signal source are set for Sharp LCD US.
Signal generator level adjustment check (Adjust to the standard value level.)
7.2.2 Process mode
Adjustment item Adjustment conditions Adjustment procedure1 Writing the software Checker process
Checking the file versionChecking the USB memory
1) Connect the USB memory to J501 (TL514-517).2) Set the PWB correctly and apply the specified voltage to it; then write the soft-
ware on it.3) After confirming the completion of the writing operation, turn off the power.4) File name
JAS_DTV_US_P101_Vx.xxx_AP.BIN(x.xxx software version)
CAUTION: When the USB memory is not inserted or reading error occurs, nothing is written.
Adjustment item Adjustment conditions Adjustment procedure1 Opposite bias adjustment
(LCD module adjustment item)
Adjustment in the center position of the panel
1) Enter the process mode using the process adjustment remote control.2) Select [VCOM ADJ] using the Channel / keys on the remote control.3) Press the Enter key to check that the pattern for adjustment is displayed.4) Make adjustment so that the flicker located in the center of the screen is mini-
mized using the Volume +/- keys on the remote control.5) If the optimum condition is obtained in step 4, press the Enter key to turn off the
pattern.
CAUTION: * Make adjustment with no ANT signal (since the brightness is changed by the active backlight).
[Adjustment position]
• 15K component signal: Y level: 0.714Vp-p± 0.02Vp-p (Pedestal to white)PB/PR level: 0.7Vp-p ± 0.02Vp-p
• 33K component signal: Y level: 0.7Vp-p ± 0.02Vp-p (Pedestal to white)PB/PR level: 0.7Vp-p ± 0.02Vp-p
• Analog RGB: RGB level: 0.7Vp-p ± 0.02Vp-p (Pedestal to white)
Adjustment point Adjustment conditions Adjustment procedureProcess mode Enter the process adjustment mode using the process adjustment remote control.
1/2 1/2
1/2
1/2
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
4 – 5
7.2.3 Component 15K signal adjustment
7.2.4 Component 33K signal adjustment
7.2.5 Analog RGB signal adjustment
Adjustment point Adjustment conditions Adjustment procedure1 Setting 480i signal
100% Full Field Color Bar• Send the 100% color bar signal to the component input.
2 Automatic adjustment exe-cution
Point the cursor to [COMP SD ADJ] and press the [Enter] key.The adjustment is complete when [OK] is displayed.
Adjustment point Adjustment conditions Adjustment procedure1 Setting 1080i signal
100% Full Field Color Bar• Send the 100% color bar signal to the component input.
2 Automatic adjustment exe-cution
Point the cursor to [COMP HD ADJ] and press the [Enter] key.The adjustment is complete when [OK] is displayed.
Adjustment point Adjustment conditions Adjustment procedure1 Setting XGA signal
100% Checkerd Pattern
Please Make Sure SYNC is OFF
• Send the 100% checker signal to the analog RGB input.Be sure to set to SYNC=OFF.
2 Automatic adjustment exe-cution
Point the cursor to [RGB ADJ] and press the [Enter] key.The adjustment is complete when [OK] is displayed.
100% white 0% black
480i100% color bar
Color saturation: 100%
100% white 0% black
1080i100% color bar
Color saturation: 100%
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
4 – 6
8. White balance adjustment
8.1. White balance adjustment
Adjustment point Adjustment conditions Adjustment procedure1 Setting 1) Set the unit to the following conditions.
AV MODE: [DYNAMIC]Backlight: +16Active Contrast: OFFAging Time: Min. 15 minutes
2) Connect the unit with the white balance adjustment jig.2 Automatic adjustment
execution[Command]Process modeKRSW0001KKT10037
SettingKY0F0000OSDS0001SBSL0016
Multi-point adjustment modeFACT0001MSET0000
Point 2WBI20200MG2G****MG2B****MG2R****
Point 1WBI10040MG1G****MG1B****MG1R****
Point 2(Doubling)WCI20200MH2G****MH2B****MH2R****
Point 1(Doubling)WCI10040MH1G****MH1B****MH1R****
MAX valueMGMR****MGMG****MGMB****
MAX value(Doubling)MHMR****MHMG****MHMB****
WritingMSET0003FACT0000
[Adjustment procedure]1) Send the “monitor adjustment process” code using the remote control.2) Set the point 2 to the specified gradation, specify the strongest color as the fixed
color, and adjust the RGB so that it becomes the standard value through negative adjustment.
3) Set the point 1 to the specified gradation, set the G correction value (640 x G value of point 2/3200) and adjust the RB so that it becomes the standard value.
4) Calculate the MAX RGB values. (For entry, see 11 below.)
5) Calculate the tilt between the MAX point and the point 2.
6) Calculate the correction value for doubling the point 2.
7) Calculate the RGB values after doubling the point 2.
8) Calculate the tilt between the point 2 and the point 1.
9) Calculate the correction value for doubling the point 1.
10)Calculate the RGB values after doubling the point 1.
11)Enter the MAX RGB values.12)Enter the RGB values after doubling the MAX values.
13)Write the adjustment values using the MSET0003 command and turn off the AC power.
Gmax = Gmax_d = 4800 Ghigh / 3200Rmax = Rmax_d = Gmax + Rhigh - Ghigh
Bmax = Bmax_d = Gmax + Bhigh - Ghigh
(4080 when Rmax, Gmax and Bmax exceed 4080 by calculating them)
Rahigh = (Rmax - Rhigh) / (4080 - 3200)Gahigh = (Gmax - Ghigh) / (4080 - 3200)Bahigh = (Bmax - Bhigh) / (4080 - 3200)
Rhigh = Rahigh (3510 - 3200)Ghigh = Gahigh (3510 - 3200)Bhigh = Bahigh (3510 - 3200)
Rhigh_d = Rhigh + RhighGhigh_d = Ghigh + Ghigh
Bhigh_d = Bhigh + Bhigh
Ralow = (Rhigh - Rlow) / (3200 - 640)Galow = (Ghigh - Glow) / (3200 - 640)Balow = (Bhigh - Blow) / (3200 - 640)
Rlow = Ralow (717 - 640)Glow = Galow (717 - 640)Blow = Balow (717 - 640)
Rlow_d = Rlow + RlowGlow_d = Glow + Glow
Blow_d = Blow + Blow
Rmax_d = RmaxGmax_d = Gmax
Bmax_d = Bmax
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
4 – 7
9. Key writing
9.1. EDID writing (Main PWB: QPWBXF905WJZZ)
9.2. DIMMER setting (Main PWB: QPWBXF905WJZZ)
Adjustment point Adjustment conditions Adjustment procedure[Adjustment value]* According to the “Standard settings” submitted by the Technical Department
[LC-32D49U] teaching set
[Adjustment standard value]Measuring instrument: [Minolta CA-210] Technical measuring instrument
Level Reference value Adjustment spec Inspection spec
Point 2 3200X=0.272
±0.0020 ±0.0040y=0.277
Point 1 640X=0.272
±0.0080 ±0.0160y=0.277
Adjustment point Adjustment conditions Adjustment procedure1 HDMI EDID writing
(Main PWB)Inspection modeFile version check
1) Write the EDID date for HDMI on IC1503/IC1504/IC1505 mounted on the main PWB using the checker.
IC1503 (HDMI1) TL1522 ⋅⋅⋅ I2C SDA TL1519 ⋅⋅⋅ I2C SCL TL1507 ⋅⋅⋅ 5V TL1510 ⋅⋅⋅ GND TL1516 ⋅⋅⋅ write protection (H: WP, L: write enable)
IC1505 (HDMI2) TL1524 ⋅⋅⋅ I2C SDA TL1521 ⋅⋅⋅ I2C SCL TL1509 ⋅⋅⋅ 5V TL1512 ⋅⋅⋅ GND TL1518 ⋅⋅⋅ write protection (H: WP, L: write enable)
IC1504 (HDMI3) TL1523 ⋅⋅⋅ I2C SDA TL1520 ⋅⋅⋅ I2C SCL TL1508 ⋅⋅⋅ 5V TL1511 ⋅⋅⋅ GND TL1517 ⋅⋅⋅ write protection (H: WP, L: write enable)
2) Write the data before being inspected by the checker.2 Analog RGB EDID
writing(Main PWB)
Inspection modeFile version check
1) Write the EDID date for analog RGB on IC508 mounted on the main PWB using the checker.
IC508 TL503 ⋅⋅⋅ I2C SDA TL502 ⋅⋅⋅ I2C SCL TL567 ⋅⋅⋅ 5V TL560 ⋅⋅⋅ GND TL568 ⋅⋅⋅ write protection (H: WP, L: write enable)
2) Write the data before being inspected by the checker.
Adjustment point Adjustment conditions Adjustment procedure1 Setting [Command]
Process modeKRSW0001KKT10037
SettingFACT0001LDIM00**
1) Type in the left commands, and enter the duty value into ** of LDIM00**.(For the suffix B only, enter 80; for other panels, enter 64.)
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
4 – 8
10. Factory settingAfter completing the factory setting, pull out the AC cord to complete the setting.
CAUTION: Do not turn on the power after completing the factory setting. If the power is turned on, configure the factory setting again.
11. Software version1. Main microcomputer
2. EDID data
3. (Reference: File name in the Technical Department)
• For HDMI
IC1503 (HDMI1): 60LE630U_hdmi_fullhd_port1_vl.bin
IC1505 (HDMI2): 60LE630U_hdmi_fullhd_port2_vl.bin
IC1504 (HDMI3): 60LE630U_hdmi_fullhd_port3_vl.bin
• For Analog RGB
IC508: 60LE630U_dsub_fullhd_256.vl.bin
Adjustment point Adjustment conditions Adjustment procedure1 Factory setting Complete the setting by
pulling out the AC cord.• Place the cursor over the item “Factory Init” and press the ENTER key.• Adjustment is complete when the green screen is displayed.• Turn off the AC power.
Be sure to check that US is displayed in the item “Factory Init”.The following items are initialized when configuring the factory setting.1) User set value2) Channel data (broadcasting frequency, etc.)3) Operating time4) Password setting value5) V-CHIP block setting value
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 1
LC60LE630U Service Manual CHAPTER 5. TROUBLESHOOTING TABLE
[1] TROUBLESHOOTING TABLE (LC-60LE630U/U(A))
No video (1)
COMPOSITE: No external input video [VIDEO]
Is VIDEO selected on the input select menu screen?
YES
NOSelect VIDEO on the input select menu screen forthe right input signal.
Does the VIDEO V1_PLUG detection function?Check the line between pin (7) of input terminal (J508) and terminal on IC3301 side of R530.
Is there the COMPOSITE signal input at terminal on IC3301 side of C3312?
YES
NOCheck the line between pin (6) of J508 and terminal on IC3301 side of C3312.
Are the LVDS signal outputs at the LVDS of SC2601?LVDS_O_D0P/N (25/26pin), LVDS_O_D1P/N (23/24pin),LVDS_O_D2P/N (21/22pin), LVDS_O_CLKP/N (18/19pin),LVDS_O_D3P/N (16/17pin), LVDS_E_D0P/N (39/40pin),LVDS_E_D1P/N (37/38pin), LVDS_E_D2P/N (35/ 36pin),LVDS_E_CLKP/N (32/33pin), LVDS_E_D3P/N (30/31pin)
NO Check IC3301 and its peripheral circuits.
YESCheck the panel module.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 2
No video (2)
COMPONENT: No external input video [COMPONENT]
Is COMPONENT selected on the input select menu screen?
YES
NOSelect COMPONENT on the input select menu screen for the right input signal.
Does the COMPONENT Y2_PLUG detection function?Check the line between pin (7) of input terminal (J502) and ter-minal on IC3301 side of R502.
Are there the COMPONENT video signal input at terminals on IC3301 side of C3321 (Y), C3323 (Pb), C3324 (Pr)?
YES
NOCheck the line between the input terminals of J502 and IC3301.
J508 pin (3) (Y), pin (5) (Pb), pin (7) (Pr)IC3301 C3321 (Y), C3323 (Pb), C3324 (Pr)
Are the LVDS signal outputs at the LVDS of SC2601?LVDS_O_D0P/N (25/26pin), LVDS_O_D1P/N (23/24pin),LVDS_O_D2P/N (21/22pin), LVDS_O_CLKP/N (18/19pin),LVDS_O_D3P/N (16/17pin)
NO Check IC3301 and its peripheral circuits.
YESCheck the panel module.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 3
No video (3)
No video at UHF/VHF broadcast signal reception No video at digital broadcast signal reception
Is the specified TV signal selected on the input select menu screen?
Is there the analog video signal output (CVBS) at pin (9) of tuner (TU1101)?
Are there the video signal outputs (DIF-/+) at pins (10) and (11) of tuner (TU1101)?
YES
NO
YES
NOCheck TU1101 and its peripheral circuits.(TU_I2C_DAT: pin (4), TU_I2C_CLK: pin (5) of TU1101, etc.)
Check TU1101 and its peripheral circuits.(TU_I2C_DAT: pin (4), TU_I2C_CLK: pin (5) of TU1101, etc.)
Is there the analog video signal input at the terminal on IC3301 side of R3334?
Are there the video signal inputs at the terminals on IC3301 side of R3340 (DIFP) and R3344 (DIFN)?
YES
NO
YES
NOCheck the line between IC3301 and TU1101, and their peripheral circuits.
Check the line between IC3301 and TU1101, and their peripheral circuits.
Are the LVDS signal outputs at the LVDS of SC2601?LVDS_O_D0P/N (25/26pin), LVDS_O_D1P/N (23/24pin), LVDS_O_D2P/N (21/22pin), LVDS_O_CLKP/N (18/19pin), LVDS_O_D3P/N (16/17pin)
NO Check IC3301 and its peripheral circuits.
YESCheck the panel module.
No video (4)
PC: No external input video [PC IN]
Is PC IN selected on the input select menu screen?
YES
NOSelect PC IN on the input select menu screen for the right input signal.
Is IC508 (EEPROM) accessed by I2C, with con-nected, to read the DDC_I2C data?Check the DDC line and its peripheral circuits.(IC508 and its peripherals)
Are there the video signal inputs at the terminals on IC3301 side of C3302 (R), C3303 (G), and C3304 (B)?Are there the VSYNC/HSYNC signal inputs at the terminals on IC3301 side of R621 and R620?
NO Check the line between SC502 and IC3301.
YESAre the LVDS signal outputs at the LVDS of SC2601?LVDS_O_D0P/N (25/26pin), LVDS_O_D1P/N (23/24pin), LVDS_O_D2P/N (21/22pin), LVDS_O_CLKP/N (18/19pin), LVDS_O_D3P/N (16/17pin)
NO Check IC3301 and its peripheral circuits.
YESCheck the panel module.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 4
<HDMI input> No video (5)-1
HDMI: No external input video [HDMI1] HDMI: No external input video [HDMI2]
Is HDMI1 selected on the input select menu screen? Is HDMI2 selected on the input select menu screen?
YES
NO
YES
NOSelect HDMI1 on the input select menu screen for the right input signal.
Select HDMI2 on the input select menu screen for the right input signal.
Does the HOT PLUG detection function? Does the HOT PLUG detection function?Does the DDC5V signal come from pin (16) of SC1501 to the ter-minal on IC3301 side of Q1508?
Does the DDC5V signal come from pin (16) of SC1503 to the terminal on IC3301 side of Q1510?
YES
NO
YES
NOCheck the line between the input terminals of SC1501 and IC3301.
Check the line between the input terminals of SC1503 and IC3301.
Check IC3301 and its peripheral circuits. Check IC3301 and its peripheral circuits.
Does the HPD signal come from pin (5) of Q1501 to pin (19) of SC1501?
Does the HPD signal come from pin (5) of Q1503 to pin (19) of SC1503?
YES
NO
YES
NOCheck the line between the pin (5) of Q1501 and the pin (19) of SC1501.
Check the line between the pin (5) of Q1503 and the pin (19) of SC1503.
Check IC3301 and its peripheral circuits. Check IC3301 and its peripheral circuits.
Is IC3301 accessed by I2C, with HDMI connected, to read DDC_I2C data?
Is IC3301 accessed by I2C, with HDMI connected, to read DDC_I2C data?
YES
NO
YES
NOCheck the HDMI_DDC line and its peripheral circuits.(Q1511 and IC1503 etc.)
Check the HDMI_DDC line and its peripheral circuits.(Q1513 and IC1505 etc.)
Are there the TMDS signal inputs at the terminals on IC3301 side of R3369/R3370 (CLK-/+), R3374/R3381 (D0-/+), R3384/R3385 (D1-/+), R3387/R3388 (D2-/+)?
Are there the TMDS signal inputs at the terminals on IC3301 side of R3347/R3348 (CLK-/+), R3349/R3350 (D0-/+), R3351/R3360 (D1-/+), R3364/R3368 (D2-/+)?
YES
NO
YES
NOCheck the line between SC1501 and IC3301. Check the line between SC1503 and IC3301.
Are the LVDS signal outputs at the LVDS of SC2601?LVDS_O_D0P/N (25/26pin), LVDS_O_D1P/N (23/24pin), LVDS_O_D2P/N (21/22pin), LVDS_O_CLKP/N (18/19pin), LVDS_O_D3P/N (16/17pin)
NO Check IC3301 and its peripheral circuits.
YESCheck the panel module.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 5
<HDMI input> No video (5)-2
HDMI: No external input video [HDMI3]
Is HDMI3 selected on the input select menu screen?
YES
NOSelect HDMI3 on the input select menu screen for the right input signal.
Does the HOT PLUG detection function?Does the DDC5V signal come from pin (16) of SC1502 to the terminal on IC3301 side of Q1509?
YES
NOCheck the line between the input terminals of SC1502 and IC3301.Check IC3301 and its peripheral circuits.
Does the HPD signal come from pin (5) of Q1502 to pin (19) of SC1502?
YES
NOCheck the line between the pin (5) of Q1502 and the pin (19) of SC1502. Check IC3301 and its peripheral circuits.
Is IC3301 accessed by I2C, with HDMI connected, to read DDC_I2C data?
YES
NOCheck the HDMI_DDC line and its peripheral circuits.(Q1512 and IC1504 etc.)
Are there the TMDS signal inputs at the terminals on IC3301 side of R3389/R3390 (CLK-/+), R3391/R3392 (D0-/+), R3393/R3394 (D1-/+), R3395/R3396 (D2-/+)?
YES
NOCheck the line between SC1502 and IC3301.
Are the LVDS signal outputs at the LVDS of SC2601?LVDS_O_D0P/N (25/26pin), LVDS_O_D1P/N (23/24pin), LVDS_O_D2P/N (21/22pin), LVDS_O_CLKP/N (18/19pin), LVDS_O_D3P/N (16/17pin)
NO Check IC3301 and its peripheral circuits.
YESCheck the panel module.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 6
No audio (1)
VIDEO No audio COMPONENT No audio
Is VIDEO selected on the input select menu screen? Is COMPONENT selected on the input select menu screen?
YES
NO
YES
NORefer to “: No external input video [VIDEO]”. Refer to “: No external input video [COMPONENT]”.
Is the audio output selected for “VARIABLE” on the menu screen? Is the audio output selected for “VARIABLE” on the menu screen?
YES
NO
YES
NOSet the audio output to “FIXED”. Set the audio output to “FIXED”.
Does the audio signal come from pins (5) (L) and (4) (R) of input terminal (J508) to the terminal on IC3301 side of C3329 (L) and C3330 (R)?
Does the audio signal come from pins (2) (L) and (4) (R) of input terminal (J504) to the terminal on IC3301 side of C3331 (L) and C3332 (R)?
YES
NO
YES
NOCheck the line between J508 and IC3301. Check the line between J504 and IC3301.
Does the I2S audio signal come from terminals on IC3301 side of R3413 (I2S_MCLK), R3414 (I2S_SCLK), R3415 (I2S_LRCLK), and R3416 (I2S_DAT) to pins (5) (MCK), (7) (SCLK), (8) (LRCLK), and (5) (SDATA) of IC2704 (AMP)?
YES
NOCheck IC3301 and its peripheral circuits.Check the line between IC3301 and IC2704.(N_AMP_RST, SP_MUTE etc.)
Is the audio output from IC2704 as specified? NO Check IC2704 and its peripheral circuits.
YESCheck the connector (P2701), speakers and their peripheral circuits.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 7
No audio (2)
[PC analog audio input] PC IN No audio [HDMI analog audio input] HDMI1 No audio
Is PC IN selected on the input select menu screen? Is HDMI1 selected on the input select menu screen?
YES
NO
YES
NORefer to “: No external input video [PC IN]”. Refer to “: No external input video [HDMI1]”.
Is the audio output selected for “VARIABLE” on the menu screen? Is the audio output selected for “VARIABLE” on the menu screen?
YES
NO
YES
NOSet the audio output to “FIXED”. Set the audio output to “FIXED”.
Is the “PC Audio Select” selected for “PC IN” on the menu screen? Is the “PC Audio Select” selected for “HDMI1” on the menu screen?
YES
NO
YES
NOSet the “PC Audio Select” to “PC IN”. Set the “PC Audio Select” to “HDMI1”.
Is the HDMI audio output selected for “Digital” on the menu screen?
YES
NOSet the HDMI audio output to “Analog”.
Does the audio signal come from pins (2) (L) and (3) (R) of input terminal (J506) to the terminal on IC3301 side of C3327 (L) and C3328 (R)?
NO Check the line between J506 and IC3301.
YESDoes the I2S audio signal come from terminals on IC3301 side of R3413 (I2S_MCLK), R3414 (I2S_SCLK), R3415 (I2S_LRCLK), and R3416 (I2S_DAT) to pins (5) (MCK), (7) (SCLK), (8) (LRCLK), and (5) (SDATA) of IC2704 (AMP)?
NO Check IC3301 and its peripheral circuits.Check the line between IC3301 and IC2704.(N_AMP_RST, SP_MUTE etc.)
YESIs the audio output from IC2704 as specified? NO Check IC2704 and its peripheral circuits.
YESCheck the connector (P2701), speakers and their peripheral circuits.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 8
No audio (3)
No audio at UHF/VHF broadcast signal reception No audio at digital broadcast signal reception
Is TV selected on the input select menu screen? Is TV selected on the input select menu screen?
YES
NO
YES
NORefer to “No video at UHF/VHF broadcast signal reception”.
Refer to “No video at digital broadcast signal reception”.
Is the audio output selected for “VARIABLE” on the menu screen? If no video appears, refer to “No video at digital broadcast signal reception”.
YES
NOSet the audio output to “FIXED”.
Is there the SIF signal output at pin (8) of tuner (TU1101)? Is the audio output selected for “VARIABLE” on the menu screen?
YES
NO
YES
NOCheck TU1101 and its peripheral circuits.(TU_I2C_DAT: pin (4), TU_I2C_CLK: pin (5) of TU1101, etc.)
Set the audio output to “FIXED”.
Is there the SIF signal input at the terminal on IC3301 side of C3335 (SIFP)?
YES
NOCheck the line between IC3301 and TU1101, and their peripheral circuits.
Does the I2S audio signal come from terminals on IC3301 side of R3413 (I2S_MCLK), R3414 (I2S_SCLK), R3415 (I2S_LRCLK), and R3416 (I2S_DAT) to pins (5) (MCK), (7) (SCLK), (8) (LRCLK), and (5) (SDATA) of IC2704 (AMP)?
NO Check IC3301 and its peripheral circuits.Check the line between IC3301 and IC2704.(N_AMP_RST, SP_MUTE etc.)
YESIs the audio output from IC2704 as specified? NO Check IC2704 and its peripheral circuits.
YESCheck the connector (P2701), speakers and their peripheral circuits.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 9
No audio (4)
HDMI1 No audio (HDMI connected)HDMI2 No audio (HDMI connected)HDMI3 No audio (HDMI connected)
[HDMI1]Is HDMI1 selected on the input select menu screen?[HDMI2]Is HDMI2 selected on the input select menu screen?[HDMI3]Is HDMI3 selected on the input select menu screen?
YES
NORefer to “: No external input video [HDMI1/2/3]”.
[HDMI1]If no video appears, refer to “No external input video (HDMI) [HDMI1]”.[HDMI2]If no video appears, refer to “No external input video (HDMI) [HDMI2]”.[HDMI3]If no video appears, refer to “No external input video (HDMI) [HDMI3]”.
Is the audio output selected for “VARIABLE” on the menu screen?
YES
NOSet the audio output to “FIXED”.
Does the I2S audio signal come from terminals on IC3301 side of R3413 (I2S_MCLK), R3414 (I2S_SCLK), R3415 (I2S_LRCLK), and R3416 (I2S_DAT) to pins (5) (MCK), (7) (SCLK), (8) (LRCLK), and (5) (SDATA) of IC2704 (AMP)?
YES
NOCheck IC3301 and its peripheral circuits.Check the line between IC3301 and IC2704. (N_AMP_RST, SP_MUTE etc.)
Is the audio output from IC2704 as specified?
YES
NOCheck IC2704 and its peripheral circuits.
Check the connector (P2701), speakers and their peripheral circuits.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 10
No audio signal at Digital Audio Output terminal (Analog sound heard)
No HDMI1/2/3 audio No audio at digital broadcast signal reception
If no video appears, refer to “No external input video (HDMI) [HDMI1/2/3]”.
If no video appears, refer to “No video at digital broadcast signal reception”.
Is there the SPDIF signal output (OPT_OUT) at terminal on IC3301 side of R3345?
NO Check the IC3301 and its peripheral circuits.
YESIs there the SPDIF signal input at pin (1) of D516 (OPTICAL OUTPUT)? NO Check the line between D516 and IC3301.
YES
No optical output under the following conditions as per HDMI requirements.* Audio contents protected.* Audio frequency beyond 48kHz.* Audio bit length beyond 16bits.
Check the speakers and the optical cable.
No monitor audio output
Is the audio output from the monitor set at “VARIABLE” or “FIXED” on the menu screen?
NO Check the IC3301 and its peripheral circuits.
YESAre there the analog audio signal outputs at the terminals on IC3301 side of R3332 (L) and R3333 (R)?
NO Check the IC3301 and its peripheral circuits.
YESDoes the audio signal come from R3332 (L) and R3333 (R) to pins (5) (L) and (4) (R) of IC2703 (monitor audio output AMP)?
NO Check IC3301 and each signals lines/its peripheral circuits.
YESDoes the audio signal come from pins (7) (L) and (1) (R) of IC2703 to pins (2) (L) and (4) (R) of J507?
NO Check the line between IC2703 and J507 and there peripheral circuits.
YES
Check the L_MUTE line and its peripheral circuits.(Q2702/Q2701, etc.)
Check the connector (J507) and their peripheral circuits, and speakers and the Cable.
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5 – 11
1) Power red/green LED
LED flashing timing chart for error notification.
Error type Power red/green LED operation (1 cycle) Pins are microprocessor pins.Lamp errorFlashes once: Fast
[Power red LED] H: On
L: Off
Judged by the ERR_PNL port. Confirmed after 10 consecutive detections at 500 ms intervals (detected only when the backlight is on).[Released]• Execute AC_ON with [INPUT] and [VOL-DOWN] on the unit
down. Then execute the function of “L ERR RESET” in the adjustment process mode menu.
• Continuous illumination for 15 minutes.
NOTE: After five detection counts, the lamp cannot be activated.Temperature errorFlashes 4 times
[Power green LED] H: On
L: Off
Judged by monitoring temperature with the temperature sensor. When the panel temperature is 58°C or more, caution is dis-played. If the panel temperature is 60°C or more, error standby is activated.[Released]Reduce the value of TEMP CAUTION (temperature caution threshold) and TEMP SHUTDOWN (temperature protection threshold) in the adjustment process mode menu.
Error TypePanel power errorFlash 2 times
H: On
L: Off
Judged panel power supply by the DET_POW_port.Conformed after 2 consecutive detections at 16mS intervals.
400ms 1600ms
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
6 – 1
LC60LE630U Service Manual CHAPTER 6. OVERALL WIRING/SYSTEM BLOCK DIAGRAM
[1] OVERALL WIRING DIAGRAM (LC-60LE630U/U(A))
1 2 10976543 8
J
A
B
C
D
E
F
G
H
I
1311 191816151412 17
[CI ] 1 3
ICON UnitDUNTKF770FM02
[LW]1
41
Rch: RSP-ZA539WJZZ
MAIN Unit
DUNTKF905FM01
[RA]
1 151 4
[SP]
[PD]POWER Unit
RUNTKA847WJQZ
1 4
[PL]
1 3
[AC]
24
1
LCD CONTROL Unit
RUNTK4911TPZT
[TK]
KEY UnitRUNTKF800FM50
HDMI
1 12
[PD]
[LW]
1
41
1 3
[CI]
[RA] 1 5
R/C OPC UnitDUNTKF494FM01
1 12
USB
1 80 1 80
TUNER
Lch: RSP-ZA538WJZZ
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
6 – 2
[2] OVERALL WIRING DIAGRAM (LC-70LE735U)
1 2 3 1097654 8
J
A
B
C
D
E
F
G
H
I
1311 191816151412 17
QCNW-M166WJQZ
[CI] 1 3
ICON UnitDUNTKF770FM03
[LW]
1 80 1 80
1
41
Rch: RSP-ZA539WJQZ
MAIN UnitDKEYMF733FM26
[RC]
1
15
15
[SP]
[PD]POWER Unit
RDENCA442WJQZ
1 4
[PL]
1 2
[AC]
TUNER
HDMI
HDMI
24
1
LCD CONTROL UnitRUNTK4909TPYP[KY]
KEY UnitDUNTKF800FM50
16 [UB]
HDMI
1 24
[PD]
[LW]1
41
14
[PL]
13 [CI]
[UB] 1 6
WiFi UnitRUNTKA810WJQZ
[RA] 1 5
R/C OPC UnitDUNTKF494FM01
HDMI
USB
USBETHER
NET
Lch: RSP-ZA538WJQZ
1
4 1 64 1 64
3D-IR EMITTER UnitRUNTKA819WJQZ
[IR] 1 3
17
1
[LA]
17
1
[LA]20
[L1]
24
[L2]
LED DRIVER
UnitRUNTKA842WJZZ
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
6 – 3
[3] SYSTEM BLOCK DIAGRAM (LC-60LE630U/U(A))
1 2 3 1097654 8
J
A
B
C
D
E
F
G
H
I
1311 191816151412 17
IC3301
MSD3402QTATSC
Digital AV decode & Main CPU
N_CPU_RST
[PD]POWERP9601(12p)
SPI_FLASH
LVDSODDDATA(8)
USB_0
Audio in
HW RESET
UART-0
RGB in
CVBS
MAIN
SIF_IN-/+
TH3301Thermister
BU5V
BackUpBU+3.3V
MAIN9V5.5V5VD3.3VB2.5VB1.8VB1.26V
POWERCIRCUIT
LAMP_ERRI/O
THERMO
I/O
UR13V
I/O
IC2704SP AMPYDA164
I2S(SDATA/LRCK/SCLK)
DiscleteMute
PC/HDMI_LRJ506
RGB/HDMI Audio(Mini Plug)
[SP]P2701EXT-SP
SPEAKER10W/10W
D516OPTICALOUT
OPT_OUT
24.000MHz
X3301X'tal
RF IN
TU1101Analog/DigitalSi-Tuner
+3.3V
RS232C_UART_RxD/TxD
TUNER_I2C(100KHz 3.3V)
J501USB
IC508EEPROM
SC502D-SUBRGB
Audio out
J508CVBS/LR
CVBS_IN
CVBS_IN_L/R
D+5.5V
PS_ON
IC502Reg
OFL1PWM
+3.3V
+2.5V
+1.8V
+1.26V
[LW]SC2601(41p)
IC3302Reset
RGB HV
TUNER_I2C
IC3501DDR2
800Mbps512Mbit
STBI/O
SC1503HDMI1 (TOP)
LRCK/SCLK/MCLK/SDATA0
+3.3V
+13V
UART-1
+5V
MAIN_SW,KEY1/2
R/C
[RC] P3301(15p)
RC
PNL_POW
AC_DET
PC/HDMI_LR
CVBS_IN_L/R
PC_VSYNC/HSYNC
PC_R/G/B
PC_VSYNC/HSYNC
PC_R/G/B
OPT_OUT
[RA]P103(5p)
BU+3.3V
+3.3V
+5V
T-CON
POWER Unit
L_MUTE
COMPONENT1 L/R
J502/J504COMPONENT1
J507MONITOR_OUT
MONITOR OUT L/R
Y1,Pb1,Pr1Y1,Pb1,Pr1
MONITOR OUT_L/R
IF_AGC
From CPU
D_IF IN-/+
Tuner_CVBS
DIF_IN-/+
COMP1_IN_L/R
IC1505EEPROM
+5V
DDC_2/HDMI_2
DDC_1/HDMI_1
DDC_0/HDMI_0
IC8401SPI FLASH32Mbit
+3.3V
ISP/Debug_RxD/TxD
I2C
IC8403EEPROM4kbit
+3.3V
IRA/CI/O
I/O
for HDCP
A/C
LVDS ODD DATA(8)
+1.8V
IC2703OP-AMP
CVBSSIF
TU_RST
N_AMP_RST From CPU
SP_MUTE
VI_PLUG
YI_PLUG
V1_PLUG
Y1_PLUG
SC1501HDMI2 (TOP)
IC1503EEPROM
+5V
SC1502HDMI3 (SIDE)
IC1504EEPROM
+5V
11,4pin
12,15pin
USB_PWRONFrom CPU
SP_L/R
[RL]P202(3p)
IR,OPC
OPC POW SW
KEYx6(MENU/INPUT
/CHANNEL/VOLUME)
[CI]P3302(3p)
CI
T-CONGuava SHARP PANEL
60"
LVDS ODD CLK(2)
LVDSEVENCLK(2)
I/OAC_CTRL
DET_POW
PNL_I2C_EN
I/O
PANEL_12V
D3.3V
B2.5V
B1.8V
B1.26V
BU3.3V
RUNTKA847WJQZPOWERCIRCUIT
MUTE_A_ALL
Q501FET SW
UART_BUS_SW
DRAM_IF
X_IN/OUT
CenterIcon LED
LED_G
KEY[KM]P501(4p)
PWMDIMMER
[PD]
(24p)
[PL]P4804
(4p)
LVDSODDDATA(8)
LVDS EVEN DATA(8)
LVDS EVEN CLK(2)
LVDSEVENCLK(2)
IC2601I2C
BUS SW
I2C
VCOM_WP
PNL_EN
ROM_WP
DET_POW
VCOM_WP
PNL E
ROM_WP
VCOM
PANEL
60Hz
60Hz
PanelPower
TCONROM
DET_SYNC
I/O
[LW]SC4801(41p)
120Hz
120Hz
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
6 – 4
[4] SYSTEM BLOCK DIAGRAM (LC-70LE735U)
1 2 3 1097654 8
J
A
B
C
D
E
F
G
H
I
1311 191816151412 17
zz
IC3303
MT5395(FHD)H.264 / VC-1
Digital AV decode & Main CPU
SPI_FLASH
/NANDFlash
LVDSOUT
USB_0
Audio in
DTV/SPDIF
I2C_1
RESET
UART-TXD0
RGB in(AK17)
DDC_I2C_1HDMI_1
CVBS
I2C_0
MAIN
SIF
PS_ON
BU5V
AC_DET
POWER CIRCUIT
MAIND5.6VD5VU5VD3.3VM1.8VD1.5VD1.1V
INPUT6
UR13V
BackUpBU+3.3V
IC2703SP AMP(2CH)YDA164
HP/MONI_L/R(PWM)
I2S(SDATA/LRCK/SCLK)DiscleteMute
PC/HDMI_LRRGB/HDMIAudio
(Mini Plug)
[SP]P2701EXT-SP
SPEAKER
OPTICALOUT
OPT_OUT
AUDIO_MUTE
27.000MHz
X3301X'tal
INPUT1
INPUT8
RF IN
UART_CPUTO232C,UART_232CTOCPU
TU_DEMOD_SCL/SDA (400KHz 3.3V)
J9502USB
IC506RS232C TxRxM3221EIP
RS-232C
+3.3V
No.9 pin RC Passthrough
IC8455EEPROM64kbit
+3.3V
INPUT7
HDMI 1(ARC)
INPUT2
INPUT2/8
D-SUBRGB
Audio out
IC3501DDR3(1333M)
2Gbit
UART-2
I2C_0
CVBS2_IN
CVBS2_IN_L/R
D_IF-/+
COMP1_IN_L/R
U5VIC9502PowerSWAP2151
OFL1PWM_0
IC8401NAND FLASH
2Gbit
+3.3V
+3.3V
+1.5V
+1.2V
+1.1V
[LW]P2601(41p)
RGB HV(AK14,AJ14)
IC1504HDMI-SWSII9387
DDC_3HDMI_3
DDC_4HDMI_4
+3.3V
Audio Out(Mini Plug)
TUNER_I2C
PWM_1
HDMI_CEC
IC3502DDR3(1333M)
2Gbit
PNL_POW
S13V
I/O
Component
COMP1_Y/Pb/Pr
HDMI 2
HDMI 3
HDMI 4
INPUT3
DDC_2HDMI_2
DDC_1HDMI_1
IC2601SpliterHC2G66DP
I2C_0 (400KHz)
ONDD8
15
OND6
N_TUN_RST
+13V
USB_1
J9501Ethernet
UART-TXD1
+5V
[RC] P2001(15p)
+5V
RC,OPC
PNL_POW
AC_DET
PC/HDMI_LR
CVBS2_IN_L/R
COMP_IN_L/R
PC_VSYNC/HSYNC
PC_R/G/B
PC_VSYNC/HSYNC
PC_R/G/B
OPT_OUT
HP/MONI_L/R
SIF
(400KHz 3.3V)
+3.3V
VON
PNL_WP
+5V
(100KHz 3.3V)I2C_1
IC9611SpliterHC2G66DP
PNL_I2C_EN
L/R_REF
DDC_0HDMI_0
T-CON
LED_Drive
POWER Unit
UR13V
I2C_1 (100KHz)
PNL_I2C_EN
AUDIO_MUTE
+3.3V
+3.3V
+1.2V
N_PER_RST
N_AMP_PROTECT
SP_MUTE
IC503
AUDIO_MUTE
INPUT4
J9504USB IC9503
PowerSWAP2181
+5V
IC9505USB2.0 HubControllerPD720114
X9502Xtal
30MHz
BU+3.3V
1.5A
0.5A
SIF
TU1105Analog/DigitalSi Tuner
CVBS
LR
LR
Component
CVBS
LR
CVBS1_IN
CVBS1_IN_L/R
CVBS1_IN_L/R
INPUT5
CVBS_Out
BU+3.3V
N_PER_RST
N_AMP_PROTECT
IC2704HP-AMPAK4201EU
+5V
VSYNC
LR_PULSE
CVBS
IC4405ATSC DemodMT5112EE
TU_SCL/SDA
X4402Xtal
25MHz
DEMOD_RST
DEMOD_TSCLK/SYNC/VAL/DATA0
+3.3V
+1.2V
N_TUN_RST
I2C_2
OFL2IC9610Spliter
HC2G66DP
+3.3V
PNL12V
I2C_1 (100KHz)
AUDIO_MUTE
ATSC_IF_AG
+1.5V
+5V
+3.3V
HDMI_CEC
IC2003BufferLCX125FT
BU+3.3V HDMICECI
HDMICECOU
Thermister
IC2001R8C/36CIXD241WJSUB MCU
LAMP_ERR
I/O
I/O
AC_DET
I/
THERMOA/D
I/O
I/O
FL2001Xtal
20MHz
STB
I/O
UART
BU+3.3V
UCOM_RST
IC2001Reset
PMREQ
N_SRESET
I2CEEPROM_SCL/SDA
IC2004EEPROM2kbit
BU+3.3V
DET_PNL12V
WP
SMPOW
PS_ON
SMPOWHOLD
I/O
I/O
I/O
AUDIO_MUTE (=N_MUTE_A_ALL)
HDMI_CEC_IN
HDMI_CEC_OUT
UCOM_MODEMODE
RESET
OR
I/O
I/O
I/O
I/O
CPU_TXD1_UCOM,CPU_RXD1_UCOM
N_SRESET
RESET
SMPOWHOLD
UART-RXD0
UART-RXD1
IC8451Buffer
+3.3V
IC8452-1
Select
IC8452-2
Select
BU+3.3VBU+3.3V
0
11
0
IC8452-3
Select
RC,OPC
RCRC_CPU
A/D
0
1
GND
42
3 R/C EMBLEM
[RA] P103(5p) [CI] P202(3p)
3D IR
[IR] (3p)
PWM
1
6
3
4
5
12
7I2C_READY
8
9
STB_CPU
RC
IR_PASS
AMP_MUTE
N_PER_RST
N_PER_RST
+5V
WOWLAN
WiFi
[US]WiFi
P9501(6p)
(6p)
UNIT
ILL_LED1_STBY_USE,ILL_LED3
[PL]PNL12V
P2605(4p)
OFL1_FRCRST
[PD]POWERP9602(24p)
35
7
11
4
2
12
10
GSPPWM1
Tr Tr
ILLLED3
[CI] P2007(3p)
ILLLED1STBYUS
+5V BU+5V
N_PNL_ENPNL_EN
+3.3V
+1.8V
TACT KEY
[KM] P151(4p)
OPC
R/C
POWSWKEY1KEY2
POWSW,KEY1,KEY2
2
1
PWM2
MAIN
T-CON
POWER(Driver)
I2C0_SCL/S
GSP
GSP
OFL
I2C1_SCL/S
I2C_0(400KHz)24.576MHz
X2701 XXtal
IC2701DSP
(YSS951)
+3.3V
+1.8V
AMP_DATA_LR
AMP_LRCK/BCLK/MCLK
AMP_HOPP
Downloaded from www.Manualslib.com manuals search engine
PARTS GUIDE
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace theseparts with specified ones for maintaining the safety and performance of the set.
This document has been published to be usedfor after sales service only.The contents are subject to change without notice.
LC-60LE630U/U(A), LC-70LE735UPartsGuide
[1] PRINTED WIRING BOARD ASSEMBLIES (LC-60LE630U/U(A))
[2] PRINTED WIRING BOARD ASSEMBLIES (LC-70LE735U)
[3] LCD PANEL MODULE UNIT
[4] CABINET PARTS (LC-60LE630U/U(A))
[5] CABINET PARTS (LC-70LE735U)
[6] SUPPLIED ACCESSORIES/PACKING PARTS (LC-60LE630U/U(A))
[7] SUPPLIED ACCESSORIES/PACKING PARTS (LC-70LE735U)
[8] SERVICE JIGS (USE FOR SERVICING)
CONTENTS
LCD COLOR TELEVISION
LC-60LE630ULC-60LE630U(A)LC-70LE735UMODELS
No. S81S460LE630U
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
2
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[1] PRINTED WIRING BOARD ASSEMBLIES (LC-60LE630U/U(A))N DUNTKF905FM01 N X MAIN UnitN DUNTKF494FM01 AG N X R/C OPC UnitN DUNTKF770FM02 AE N X ICON UnitN DUNTKF800FM50 AF N X KEY Unit
! N RUNTKA847WJQZ BM X POWER/DRIVE UnitN RUNTK4911TPZT N X LCD CONTROL Unit
[2] PRINTED WIRING BOARD ASSEMBLIES (LC-70LE735U)N DKEYMF733FM26 N X MAIN UnitN DUNTKF494FM01 AG N X R/C OPC UnitN DUNTKF770FM03 AG N X ICON UnitN DUNTKF800FM50 N X KEY UnitN RUNTKA810WJQZ X WiFi UnitN RUNTKA819WJQZ X 3D IR EMITTER Unit
! N RDENCA442WJQZ X POWER UnitN RUNTK4909TPYP N X LCD CONTROL UnitN RUNTKA842WJZZ X LED DRIVER Unit
[3] LCD PANEL MODULE UNITN R1LK600D3GW70Z X 60" LCD Panel Module Unit (LK600D3GW70Z) (LC-60LE630U)N R1LK600D3GW7AZ X 60" LCD Panel Module Unit (LK600D3GW7AZ) (LC-60LE630U(A))N R1LK695D3GW20Z N X 70" LCD Panel Module Unit (LK695D3GW20Z) (LC-70LE735U)
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
3
[4] CABINET PARTS (LC-60LE630U/U(A))
2
42
31
22
25 45
3021
42
46
44
23
2643
3
20
20
20
5
3
27
27
6
7
32
34
29
32
34
27
20
20
20 4242
24
8
35
10
8
8
10
7
4329
1-1 1-4
1-3
1-2
1-6
47 1-5
1
40
41
37
28
42
14
19
187
17
48
7
39
449
50
1651
36
KEY Unit
POWER/DRIVE Unit
60" LCDPanel Module Unit
LCD CONTROLUnit
R/C OPC Unit
ICON Unit
A
B
j
D
EC
H
G
A
H
F
G
C
D
E
e
h
k
dd
kd
ac
f
MAIN Unit
c
f
a
d
F
je
h
B
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
4
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[4] CABINET PARTS (LC-60LE630U/U(A))1 CCABAC748WJ33 N X Front Cabinet Ass'y
1-1 Not available - - Front Cabinet1-2 Not available - - R/C OPC Cover1-3 HDECQB607WJ3C N X Front Decoration1-4 LHLDWA133WJKZ AC J Wire Holder1-5 Not available - - Sheet1-6 TLABZC966WJZZ N X DOLBY-ENE Label2 GCABBC003WJ3A N X Rear Cabinet3 LANGKD122WJM2 J Center Angle, x24 LANGKD341WJFW N X Terminal Angle (Side)5 LHLDWA133WJKZ AC J Wire Holder6 LHLDWA138WJKZ AC J Wire Holder, x27 LX-BZA207WJF7 AA J Screw, x168 NSFTZA459WJF7 AC J Tray Shaft, x610 PSPANA044WJKZ AB J POWER PWB Spacer, x514 PZETKA595WJKZ J AC Cord Barrier16 QCNW-M106WJQZ N X Connecting Cord (PD)17 QCNW-M144WJQZ N X Connecting Cord (LW)18 QCNWN2731TPZZ AF J FFC (80pin), x219 RCORFA061WJZZ AG J Ferrite Core, x220 XBPS830P06WS0 AA J Screw, x1621 GCOVAC576WJKZ AC J VESA Hole Cover, x422 GCOVAD981WJ3A J AC Cord Cover23 GCOVAE060WJ3A J Key Button Cover24 GCOVAE130WJ3A J Bottom Cover25 HiNDPE297WJSA N X Model Label (LC-60LE630U)25 HiNDPE341WJSA N X Model Label (LC-60LE630U(A))26 JBTN-A912WJ3A J Key Button27 LANGKD127WJFW AD J Fixing Metal Angle, x1428 LANGKD265WJFW J Fixing Metal Angle29 LHLDWA175WJUZ AC J Wire Holder, x330 LHLDWA303WJKA AE J Cable Clamp31 LX-BZA401WJN1 AC J Screw, x332 PSPAKA486WJKZ AD J Spacer, x234 PSPAZC777WJZZ N X Spacer, x2
! 35 QACCDA084WJPZ J AC Cord36 QCNW-M107WJQZ N X Connecting Cord (CI)37 QCNW-M108WJQZ N X Connecting Cord (SP)39 QCNW-L938WJQZ J Connecting Cord (RA)40 RSP-ZA538WJQZ J Speaker (L)41 RSP-ZA539WJQZ J Speaker (R)42 XBPS830P06WS0 AA J Screw, x3543 XEBS830P08000 AA J Screw, x344 XEBS830P12000 AA J Screw, x1045 TLABNB037WJZZ J Serial Label (Back)46 Not available - N - Serial Label (Side)47 HiNDPE319WJZZ N X ENERGY GUIDE Label48 LANGKD342WJFW N X Earth Angle49 PMLT-A681WJQZ J Gasket (Tuner)50 PSPAZC730WJKZ J Spacer51 XBPS830P06000 AA J Screw, x2
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
5
[5] CABINET PARTS (LC-70LE735U)
26
2942
2-1
2-4
2-2
2-3
41
43
27
43
25
43
2
24
3-1
3-1
3-1
3-2
3-2
3-2
3-2
3
3
3
3
3-1
5
24
2424
5 24
34
49
51
11
11
11
12
11
13
12
17
18
16
614
39
7
48
710
10
40
32
30
30 30-1
30-1
30-2
30-2
30-1
30-2
30
354
4
1-1
1-8
1
42 9
45
28
44
31
37
19
38
1-3
1-7
1-2
1-6
1-4
1-5
21
20
36
11
11
47
2233
23
23
22
52
KEY Unit
POWER Unit
LED DRIVER Unit
MAIN Unit
f
70" LCD PanelModule Unit
LCD CONTROL Unit
R/C OPC Unit
3D IR EMITTER UnitICON Unit
WiFi Unit
A
B
E
D
J
K
b
m
m
kk
H
F
G
C
B
A
H
EK
JD
C
F
G
b
eg
g
e
h
k
f
c
a
jhk
a
k
c
d
d
j
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
6
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[5] CABINET PARTS (LC-70LE735U)1 CCABAC768WJ34 N X Front Cabinet Ass'y
1-1 Not available - - Front Cabinet1-2 Not available - - R/C OPC Cover1-3 HDECQB633WJ3A N X Front Decoration1-4 LHLDWA124WJKZ AC J Wire Holder, x31-5 LHLDWA175WJUZ AC J Wire Holder, x51-6 Not available - - Sheet1-7 TLABZC778WJZZ J WiFi Label1-8 TLABZC636WJZZ J Quattron Label2 CCABBB968WJ31 J Rear Cabinet Ass'y
2-1 Not available - N - Rear Cabinet2-2 HiNDPE031WJSA J Terminal Indicator (Bottom)2-3 HiNDPE034WJSA J Terminal Indicator (Back)2-4 HiNDPE116WJSA J Terminal Indicator (Side)3 CANGKD289WJ31 J VESA Angle Ass'y, x4
3-1 Not available - N - VESA Angle3-2 Not available - N - VESA Shaft4 GCOVAE164WJ3A J Bottom Cover, x25 LANGKD290WJ3W J Stand Angle, x26 LANGKD292WJ3W J Terminal Angle (Bottom)7 LHLDWA124WJKZ AC J Wire Holder, x69 LHLDWA175WJUZ AC J Wire Holder10 LHLDWA176WJUZ AC J Wire Holder, x411 LX-BZA207WJF7 AA J Screw, x2412 PMLT-A678WJQZ J Gasket, x213 PMLT-A679WJQZ J Gasket14 PMLT-A680WJQZ J Gasket16 PSLDMB762WJ3W J Shield (MAIN Unit)17 PSPAZC740WJZZ J Spacer18 PSPAZC741WJKZ J Spacer19 QCNW-M029WJQZ J Connecting Cord (PD)20 QCNW-M031WJQZ J Connecting Cord (PL)21 QCNW-M168WJQZ N X Connecting Cord (LW)22 QCNWN2731TPZZ AF J FFC (80pin), x223 RCORFA061WJZZ AG J Ferrite Core, x424 XBPS830P06WS0 AA J Screw, x2825 GCOVAC576WJKZ AC J VESA Hole Cover, x426 GCOVAE162WJ3A J Key Button Cover27 GCOVAE163WJ3A J AC Cord Cover28 HiNDPE267WJSA N X Model Label29 JBTN-A912WJ3A J Key Button30 CANGKD291WJ31 J Fixing Metal Angle Ass'y, x14
30-1 Not available - N - Fixing Metal Angle30-2 Not available - N - Spacer31 LHLDWA303WJKA AE J Cable Tie32 LX-EZA069WJF7 AB J Screw, x233 QCNWN2732TPZZ AF J FFC (64pin), x2
! 34 QACCDA084WJPZ J AC Cord35 QCNW-M030WJQZ J Connecting Cord (SP)36 QCNW-M167WJQZ N X Connecting Cord (RC)37 QCNW-M034WJQZ J Connecting Cord (CI)38 QCNW-M035WJQZ J Connecting Cord (UB)39 RSP-ZA538WJQZ J Speaker (L)40 RSP-ZA539WJQZ J Speaker (R)41 XBPS830P06WS0 AA J Screw, x2142 XEBS830P08000 AA J Screw, x343 XEBS830P12000 AA J Screw, x1044 TLABNB037WJZZ J Serial Label (Back)45 Not available - N - Serial Label (Side)47 PSPAZC782WJKZ N X Spacer48 LHLDWA151WJKZ AB J Wire Holder49 QCNW-M166WJQZ J Connecting Cord (LA)51 PSPANA044WJKZ AB J PWB Spacer52 HiNDPE366WJZZ N X ENERGY GUIDE Label
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
7
[6] SUPPLIED ACCESSORIES/PACKING PARTS (LC-60LE630U/U(A))
X4Remote control unit (x1)
X9“AA” size battery (x2)
X1 X2 X3
Stand support Ass'y (x2) Stand Base Ass'y (x1) Stand Screw Ass'y (x1)
X7
X5 Enquete card
X6 Guarantee card
Operation manual (x1)
S1
S4
S6
FRONT
S9
S8
S6
S6
X2
X4
X3
S5X1
X9
X5X6X7
S7
S10
S10
S7
S2
S7
S3
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
8
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[6] SUPPLIED ACCESSORIES/PACKING PARTS (LC-60LE630U/U(A))X1 CANGKD276WJ01 J Stand Support Ass'y, x2X2 CDAi-A778WJ31 J Stand Base Ass'yX3 CSAKKA011WJ01 J Stand Screw Ass'yX4 RRMCGA667WJSA X Remote ControlX5 TCADEA243WJZZ J Enquete CardX6 Not available - - Guarantee CardX7 TiNS-F234WJZZ N X Operation Manual (E)X7 TiNS-F235WJZZ N X Operation Manual (F)X7 TiNS-F236WJZZ N X Operation Manual (S)X9 Not available - - "AAA" size battery, x2S1 SPAKCG446WJZZ - N - Packing Case (NOT REPLACEMENT ITEM)S2 SPAKCF960WJZZ - - Packing Case (Bottom) (NOT REPLACEMENT ITEM)S3 SPAKPB427WJZZ - - Wrapping Paper (NOT REPLACEMENT ITEM)S4 SPAKPB722WJZZ - N - Wrapping Paper (Stand) (NOT REPLACEMENT ITEM)S5 SPAKPB723WJZZ - N - Wrapping Paper (Support) (NOT REPLACEMENT ITEM)S6 SPAKXD367WJZZ - - Packing Add. (Top) (NOT REPLACEMENT ITEM)S7 SPAKXD368WJZZ - - Packing Add. (Bottom) (NOT REPLACEMENT ITEM)S8 SSAKA0101GJZZ - - Polyethylene Bag (NOT REPLACEMENT ITEM)S9 SSAKKA011WJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)S10 TLABKA009WJZZ - - Case No. Label (NOT REPLACEMENT ITEM)
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
9
[7] SUPPLIED ACCESSORIES/PACKING PARTS (LC-70LE735U)
S6
X2S4
X1S5
X10
X5
X3S12
X6S10
X8X9
X7
S8
S2
S8
S8
S1
S13
S13
S8
S7
S7
S8
S7
X5Remote control unit (x1)
X10“AAA” size battery (x2)
X1 X2 X3Stand support Ass'y (x2) Stand Base Ass'y (x1) Stand Screw Ass'y (x1)
X8 X9
X6 Enquete card
X7 Guarantee card
Operation manual (x1) Connection guide (x1)
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
10
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[7] SUPPLIED ACCESSORIES/PACKING PARTS (LC-70LE735U)X1 CANGKD276WJ01 J Stand Support Ass'y, x2X2 CDAi-A778WJ31 J Stand Base Ass'yX3 CSAKKA011WJ01 J Stand Screw Ass'yX5 RRMCGA936WJSA X Remote ControlX6 TCADEA243WJZZ J Enquete CardX7 Not available - - Guarantee CardX8 TiNS-F207WJZZ N X Operation ManualX9 TMAN-A043WJZZ J Connection GuideX10 Not available - - "AAA" size battery, x2S1 SPAKCG413WJZZ - N - Packing Case (NOT REPLACEMENT ITEM)S2 SPAKCG317WJZZ - - Packing Case (Bottom) (NOT REPLACEMENT ITEM)S4 SPAKPB722WJZZ - N - Wrapping Paper (Stand) (NOT REPLACEMENT ITEM)S5 SPAKPB723WJZZ - N - Wrapping Paper (Support) (NOT REPLACEMENT ITEM)S6 SPAKPB733WJZZ - - Wrapping Paper (NOT REPLACEMENT ITEM)S7 SPAKXD394WJZZ - - Packing Add. (Top) (NOT REPLACEMENT ITEM)S8 SPAKXD395WJZZ - - Packing Add. (Bottom) (NOT REPLACEMENT ITEM)S10 SSAKA0101GJZZ - - Polyethylene Bag (NOT REPLACEMENT ITEM)S12 SSAKKA011WJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)S13 TLABKA009WJZZ - - Case No. Label (NOT REPLACEMENT ITEM)
[8] SERVICE JIGS (USE FOR SERVICING)N QCNW-C222WJQZ AW J Connecting Cord L=1000mm 80pins, LCD Control Unit to LCD Panel Unit, x2N QCNW-F676WJQZ BH J Connecting Cord L=1000mm 41pins, MAIN Unit to LCD Control Unit (LW)N QCNW-M249WJQZ N J Connecting Cord L=1000mm, Main to LCD Control Unit (PD) (LC-60LE630U/U(A))
N QCNW-L214WJQZ AV JConnecting Cord L=1000mm, 64pins, LCD Control Unit to LCD Panel Unit, x2 (LC-70LE735U)
N QCNW-G405WJQZ AP JConnecting Cord L=1000mm 4pins, POWER Unit to LCD Control Unit (PL) (LC-70LE735U)
N QCNW-L795WJQZ BC J Connecting Cord L=1000mm 24pins, MAIN Unit to POWER Unit (PD) (LC-70LE735U)
N QCNW-L519WJQZ N JConnecting Cord L=1000mm 18pins, LED DRIVER Unit to POWER Unit (LA) (LC-70LE735U)
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
Downloaded from www.Manualslib.com manuals search engine
LC-60LE630U/U(A), LC-70LE735U
COPYRIGHT © 2011 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATIONAV Systems GroupCS Promotion CenterYaita,Tochigi 329-2193, Japan
Jul. 2011SH. DS
Downloaded from www.Manualslib.com manuals search engine
top related