katalog plechy 2009 en - · pdf file2 the 3.5 m four-high rolling mill the rolling mill was...
Post on 16-Feb-2018
215 Views
Preview:
TRANSCRIPT
PLATES
PRODUCT CATALOGUE
2
THE 3.5 M FOUR-HIGH ROLLING MILL
The rolling mill was founded in 1971 and underwent a large modernization in 1999 which facilitated a considerable improvement of the rolled material geometry, surface quality and expansion of the product mix. Plates are made from concast slabs. Plates are rolled in the thickness range from 5 to 80 mm, and in the width range from 1000 to 3300 mm.
THE PLATE PRODUCT MIX IS DESIGNED FOR:
• Steel and bridge structures• Ship building• Transport machines and vehicles• Atmospheric corrosion resistant structures• Pipelines• Offshore structures• Pressure vessels used in normal or elevated temperatures• Flame cut shapes• Case hardened components• Nitrided components• Tools
QUALITY MANAGEMENT SYSTEM AND ENVIRONMENTAL MANAGEMENT SYSTEM,PRODUCT CERTIFICATION
EVRAZ VÍTKOVICE STEEL, a.s. holds the Quality Management System (QMS) Certifi cate acc. to EN ISO 9001:2000, API Spec. Q1 and Environmental Management System Certifi cate (EMS) acc. to EN ISO 14001:2004.EVRAZ VÍTKOVICE STEEL, a.s. has also certifi cation of its products according to the requirements of classifi cation societies and legislation.
Presentation of the Plates rolling mill
Plates
3
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PLATES OF STRUCTURAL STEELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 • Plates of steels according to EN 10025-2 • Plates of fi ne-grain steels according to EN 10025-3 • Thermomechanical rolled plates of fi ne-grain steels according to EN 10025-4 • Plates of steels according to ASTM • Plates of fi ne-grain steels according to ASTM
PLATES OF STRUCTURAL STEELS WITH IMPROVED ATMOSPHERIC CORROSION RESISTANCE (ATMOFIX) . . . . . . . . . . . . . . . . . . . . . 9 • Plates of steels according to EN 10025-5 • Plates of steels according to ASTM
PLATES FOR OFFSHORE STRUCTURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 • Normalized plates of steels according to EN 10225 • Thermomechanical rolled plates of steels according to EN 10225 • Plates according to API 2H
THERMOMECHANICAL ROLLED PLATES FOR WELDED PIPES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 • Plates for pipes according to API 5L and EN 10208-2 (sweet service) • Plates for pipes according to API 5L and EN 10208-2 (sour service)
PLATES FOR SHIP BUILDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 • Plates according to individual shipping companies • Plates according to ASTM A131
HOT-ROLLED PLATES FOR COLD FORMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 • Thermomechanical rolled plates of steels according to EN 10149-2 • Normalized plates of steels according to EN 10149-3
QUENCHED AND TEMPERED PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 • Quenched and tempered plates of 500 Q and 690 Q steel grades according to EN 10025-6 and EN 10028-6
PLATES OF NON ALLOY OR ALLOY STEELS FOR QUENCHING AND TEMPERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 • Plates of steels according to EN 10083-2 and EN 10083-3 • Plates of steels according to ASTM A 827, A 829, A 830
PLATES OF CASE HARDENING STEELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 • Plates of steels according to EN 10084
PLATES OF NITRIDING STEELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 • Plates of steels according to EN 10085
PLATES OF TOOL STEELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 • Plates of steels according to EN ISO 4957
PLATES OF STEELS FOR PRESSURE VESSELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 • Plates of steels for simple pressure vessels according to EN 10207 • Plates of steels according to EN 10028-2 • Plates of fi ne-grain steels according to EN 10028-3 • Thermomechanical rolled plates of fi ne-grain steels according to EN 10028-5 • Plates of steels according to ASTM/ASME • Plates of fi ne-grain steels according to ASTM/ASME
DELIVERY CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
MATERIAL CERTIFICATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MARKING OF PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DIMENSIONAL TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 • Table 1 – Maximum available plates length [m] for steels with minimum tensile strength Rm up to 530 MPa • Table 2 – Maximum available plates length [m] for steels with minimum tensile strength Rm more than 530 MPa • Table 3 – Maximum available plates length [m] for thermomechanical rolled plates • Table 4 – Maximum available plates length [m] for thermomechanical rolled plates for welded pipes
Contents
4
Introduction
Plates
This catalogue briefl y outlines chemical and mechanical properties of commonly used steel plates.
Properties of commonly used steel plates 1)
Length (max.) 16000 mm
Width (max.) 3300 mm
Thickness 2) 5–80 mm
Weight (max.) 3) 8500 kg
1) All dimensions listed are approximate. Actual plate sizes available depend on the combination of length, width and thickness as well as on material specifi cation. For particular information, contact EVRAZ VÍTKOVICE STEEL, a.s.
2) Higher thickness on agreement3) Higher weight on agreement
DELIVERY CONDITIONS OF PLATES (HEAT TREATMENT):
AR – As rolledN – NormalizedNT – Normalized and temperedA – AnnealedM (TMCP) – Thermomechanical rolledQT – Quenched and tempered
FOR MORE INFORMATION OR ASSISTANCE REGARDING YOUR STEEL PLATE NEEDS, PLEASE, CONTACT EVRAZ VÍTKOVICE STEEL, a.s.
Phone: +420 595 952 435Fax: +420 595 952 144E-mail: tradesteel@cz.evraz.com
5
Plates of structural steels
PLATES OF STEELS ACCORDING TO EN 10025-2
The most commonly used structural steels having minimum yield strength min. 235 MPa and guaranteed weldability that can be used for low demanding steel structures for bridges, halls, parts of railway and motor vehicles, etc.
DesignationMin. Yield
Strength ReH 2)
[MPa]
TensileStrength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV
[°C/J] – longitudinalCEV max. 1) Dimension
Table No.
Max. Thickness
[mm]
Max. Thickness for option (C)
[mm]
S235JR(C) 235 360–510 24 +20/27 0.35 1 80 3) 30 4)
S235J0(C) 235 360–510 24 0/27 0.35 1 80 3) 30 4)
S235J2(C) 235 360–510 24 -20/27 0.35 1 80 3) 30 4)
S275JR(C) 275 410–560 21 +20/27 0.40 1 80 3) 30 4)
S275J0(C) 275 410–560 21 0/27 0.40 1 80 3) 30 4)
S275J2(C) 275 410–560 21 -20/27 0.40 1 80 3) 30 4)
S355JR(C) 355 470–630 20 +20/27 0.45 1 80 3) 30 4)
S355J0(C) 355 470–630 20 0/27 0.45 1 80 3) 30 4)
S355J2(C) 355 470–630 20 -20/27 0.45 1 80 3) 30 4)
S355K2(C) 355 470–630 20 -20/40 0.45 1 80 3) 30 4)
1) ; valid for thickness up to 30 mm, for higher thickness refer to the standard2) Valid for thickness up to 16 mm, for higher thickness refer to the standard3) Higher thickness on agreement4) Under standard
EQUIVALENT DESIGNATION
EN 10025-2 EN 10025+A1 DIN 17100 BS 4360 NFA 35-501
S235JR(C) S235JRG2(C) RSt 37 - 2 40 B E 24 - 2
S235J0(C) S235J0(C) St 37 - 3U 40 C E 24 - 3
S235J2(C) S235J2G4(C) St 37 - 3N 40 D E 24 - 4
S275JR(C) S275JR(C) St 44 - 2 43 B E 28 - 2
S275J0(C) S275J0(C) St 44 - 3U 43 C E 28 - 3
S275J2(C) S275J2G4(C) St 44 - 3N 43 D E 28 - 4
S355JR(C) S355JR(C) – 50 B E 36 - 2
S355J0(C) S355J0(C) St 52 - 3U 50 C E 36 - 3
S355J2(C) S355J2G4(C) St 52 - 3N 50 D –
S355K2(C) S355K2G4(C) – 50 DD E 36 - 4
6
Plates of structural steels
Plates
PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10025-3
Structural steels with guaranteed fi ne-grain structure and low carbon equivalent. Because of the min. yield strength up to 460 MPa and impact energy guaranteed at temperature -50 °C these steels are suitable for more demanding steel structures and their supporting ele-ments. They are suitable for construction of railway and motor vehicles, too.
DesignationMin. Yield
Strength ReH 2)
[MPa]
TensileStrength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV
[°C/J] – longitudinalCEV max. 1) Dimension
Table No.
Max. Thickness
[mm]
S275N (NL) 275 370–510 24 -20/40 (-50/27) 0.40 1 80 3)
S355N (NL) 355 470–630 22 -20/40 (-50/27) 0.43 1 80 3)
S420N (NL) 420 520–680 19 -20/40 (-50/27) 0.48 1 80
S460N (NL) 460 550–720 17 -20/40 (-50/27) 0.53 2 80
1) ; valid for thickness up to 63 mm; for higher thickness refer to the standard2) Valid for thickness up to 16 mm, for higher thickness refer to the standard3) Higher thickness on agreement
EQUIVALENT DESIGNATION
EN 10025-3 EN 10113-2 DIN 17102
S275N S275N StE 285
S275NL S275NL TStE 285
S355N S355N StE 355
S355NL S355NL TStE 355
S420N S420N StE 420
S420NL S420NL TStE 420
S460N S460N StE 460
S460NL S460NL TStE 460
7
Plates of structural steels
THERMOMECHANICAL ROLLED PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10025-4
Thermomechanical rolled plates of structural steels having low carbon equivalent, and thus an excellent weldability. They are used for more demanding steel structures and their supporting elements. The impact energy is guaranteed also at temperature -50 °C which facilitates a wide range for their usage.
Designation Min. Yield
Strength ReH 2)
[MPa]
TensileStrength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV
[°C/J] – longitudinalCEV max. 1) Dimension
Table No.
Max. Thickness
[mm]
S275M (ML) 275 370–530 24 -20/40 (-50/27) 0.34 3 40
S355M (ML) 355 470–630 22 -20/40 (-50/27) 0.39 3 40
S420M (ML) 420 520–680 19 -20/40 (-50/27) 0.43 3 30 3)
S460M (ML) 460 540–720 17 -20/40 (-50/27) 0.45 3 22 3)
1) 2) Valid for thickness up to 16 mm, for higher thickness refer to the standard3) Higher thickness on agreement
EQUIVALENT DESIGNATION
EN 10025-4 EN 10113-3 SEW 092
S275M S275M –
S275ML S275ML –
S355M S355M QStE 380 TM
S355ML S355ML –
S420M S420M QStE 420 TM
S420ML S420ML –
S460M S460M QStE 460 TM
S460ML S460ML –
8
Plates of structural steels
Plates
PLATES OF STEELS ACCORDING TO ASTM
Designation GradeMin. Yield Strength[MPa]
TensileStrength Rm
[MPa]
Min. Elongation 200/50
[%]
Min. Impact Energy KV 1)
[°C/J] – longitudinal
DimensionTable No.
Max. Thickness
[mm]
A 36 250 400–550 20/23 2) 1 80
A 283
A 165 310–415 27/30 2) 1 80
B 185 345–450 25/28 2) 1 80
C 205 380–515 22/25 2) 1 80
D 230 415–550 20/23 2) 1 80
A 52950 (345) 345 485–690 18/21 2) 1 25 3)
55 (380) 380 485–690 17/20 2) 1 25 3)
Maximum value of the carbon equivalent as per the formula on agreement1) Testing on agreement2) Testing temperature and minimum impact energy on agreement3) Under standard
PLATES OF FINE-GRAIN STEELS ACCORDING TO ASTM
Designation GradeMin. Yield Strength [MPa]
TensileStrength Rm
[MPa]
Min. Elongation200/50
[%]
Min. Impact Energy KV 1)
[°C/J] – longitudinal
DimensionTable No.
Max. Thickness
[mm]
A 572(type 1, 2, 3)
42 (290) 290 415 min. 20/24 2) 1 80
50 (345) 345 450 min. 18/21 2) 1 80
55 (380) 380 485 min. 17/20 2) 1 50 3)
60 (415) 415 520 min. 16/18 2) 1 32 3)
A 573
58 (400) 220 400–490 21/24 2) 1 40 3)
65 (450) 240 450–530 20/23 2) 1 40 3)
70 (485) 290 485–620 18/21 2) 1 40 3)
A 633
A 290 430–570 18/23 -60/20 1 80
C 345 485–620 18/23 -60/20 1 80
D 345 485–620 18/23 -60/20 1 80
E 415 550–690 18/23 -60/20 2 80
Maximum value of the carbon equivalent as per the formula on agreement1) Testing on agreement 2) Testing temperature and minimum impact energy on agreement3) Under standard
9
Plates of structural steels with improved atmospheric corrosion resistance (ATMOFIX)
Plates of structural steels with improved atmospheric corrosion resistance do not require – unlike common steels – expensive surface treatments (painting). They feature increased resistance even against impacts of atmosphere which contains sulphur. Their key use is in the area of construction and building of bridges but they can be used for chimney/stack and waste gas ducts structures, too.
PLATES OF STEELS ACCORDING TO 10025-5
DesignationMin. Yield
Strength ReH[MPa]
TensileStrength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV
[°C/J] – longitudinalCEV max. 1) Dimension
Table No.
Max. Thickness
[mm]
S235J0W 235 2) 360–510 24 0/27 0.44 1 80
S235J2W 235 2) 360–510 24 -20/27 0.44 1 80
S355J0WP 355 470–630 20 0/27 0.52 1 12 3)
S355J2WP 355 470–630 20 -20/27 0.52 1 12 3)
S355J0W 355 2) 470–630 20 0/27 0.52 1 80
S355J2W 355 2) 470–630 20 -20/27 0.52 1 80
S355K2W 355 2) 470–630 20 -20/40 0.52 1 80
1) 2) Valid for plates with thickness up to 16 mm, for higher thickness refer to the standard 3) Under standard
EQUIVALENT DESIGNATION
EN 10025-5 EN 10155 SEW 087 CAN/CSA – G40.21-M
S235J0W S235J0W – –
S235J2W S235J2W WTSt 37 - 3 –
S355J0WP S355J0WP – –
S355J2WP S355J2WP – –
S355J0W S355J0W – –
S355J2W S355J2G2W WTSt 52 - 3 350AT
S355K2W S355K2G2W – –
PLATES OF STEELS ACCORDING TO ASTM
Designation GradeMin. YieldStrength[MPa]
TensileStrength Rm
[MPa]
Min. Elongation 200/50
[%]
Min. ImpactEnergy KV 1)
[°C/J] – longitudinal
Dimension Table No.
Max. Thickness
[mm]
A 588
A 345 485 min. 18/21 2) 1 80
B 345 485 min. 18/21 2) 1 80
C 345 485 min. 18/21 2) 1 80
K 345 485 min. 18/21 2) 1 80
Maximum value of the carbon equivalent as per the formula on agreement1) Testing on agreement2) Testing temperature and minimum impact energy on agreement
10
Plates for offshore structures
Plates
NORMALIZED PLATES OF STEELS ACCORDING TO EN 10225
Designation GroupMin. Yield
Strength ReH[MPa]
TensileStrength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV
[°C/J]
CEV max. 3)
Pcm max. 4)
Dimension Table No.
Max. Thickness
[mm]
S355G2+N 1 355 1) 470–630 22 -20/50 7) 0.43 ... 1 20 5)
S355G3+N 1 355 1) 470–630 22 -40/50 7) 0.43 ... 1 40 5)
S355G7+N 2 355 2) 470–630 22 -40/50 8) 0.43 0.24 1 62 6)
S355G8+N 3 355 2) 470–630 22 -40/50 8) 0.43 0.24 1 62 6)
S355G9+N 2 355 2) 470–630 22 -40/50 8) 0.43 0.22 1 62 6)
S355G10+N 3 355 2) 470–630 22 -40/50 8) 0.43 0.22 1 62 6)
THERMOMECHANICAL ROLLED PLATES OF STEELS ACCORDING TO EN 10225
Designation GroupMin. Yield
Strength ReH[MPa]
TensileStrength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV
[°C/J]
CEV max. 3)
Pcm max. 4)
Dimension Table No.
Max. Thickness
[mm]
S355G5+M 1 355 1) 470–610 22 -20/50 7) 0.43 ... 3 20 5)
S355G6+M 1 355 1) 470–610 22 -40/50 7) 0.43 ... 3 40 5)
S355G7+M 2 355 2) 470–630 22 -40/50 8) 0.43 0.24 3 40
S355G8+M 3 355 2) 470–630 22 -40/50 8) 0.43 0.24 3 40
S355G9+M 2 355 2) 470–630 22 -40/50 8) 0.41 0.21 3 40
S355G10+M 3 355 2) 470–630 22 -40/50 8) 0.41 0.21 3 40
S420G1+M 2 420 1) 500–660 19 -40/60 8) 0.42 0.22 3 30
S420G2+M 3 420 1) 500–660 19 -40/60 8) 0.42 0.22 3 30
S460G1+M 2 460 1) 540–700 1) 17 -40/60 8) 0.43 0.22 3 30
S460G2+M 3 460 1) 540–700 1) 17 -40/60 8) 0.43 0.22 3 30
1) Valid for thickness up to 16 mm, for higher thickness refer to the standard 2) Valid for thickness up to 25 mm, for higher thickness refer to the standard 3) 4)
PLATES ACCORDING TO API 2H
GradeMin. YieldStrength[MPa]
TensileStrength Rm
[MPa]
Min. Elongation 200/50
[%]
Min. Impact Energy KV
[°C/J] – transverseCEV max. 1) Dimension
Table No.
Max. Thickness
[mm]
42 289 427–565 18/22 -40/340.43 2)
1 800.45 3)
50345 2)
483–620 16/21 -40/410.43 4)
2 80324 3) 0.45 5)
1) 2) For width to 2 1⁄2“3) For width over 2 1⁄2“4) For width to 2“5) For width over 2“
Pcm = C+ + + + + + 5BSi30
Mn+Cu+Cr20
Ni60
Mo15
V10
5) Under standard6) Higher thickness up to 75 mm on agreement7) Longitudinal8) Transverse
11
Thermomechanical rolled plates for welded pipes
Thermomechanical rolled plates of non-alloyed and micro-alloyed steels with excellent weldability, designed exclusively for welded pipelines for combustible and non-combustible fl uids. These can be supplied only upon agreement on the basis of Technical Conditions negotiated between the manufacturer and the customer for supplies of these plates. Technical Conditions must specify all requirements of the customer for the plates subject to the order.
PLATES FOR PIPES ACCORDING TO API 5L 1) AND EN 10208-2 1) ( SWEET SERVICE )
Grade acc. API-5L Designation acc. EN 10208-2
Yield Strength Rt0,5 (Rt0,2) 2) [MPa]
TensileStrength Rm 2) [MPa]
Min. Elongation 2)
[%] CEV max.2) Dimension Table No.
Max. Thickness 3)
[mm]
B L245MB 245 - 440 415 - 760 22 0.40 4 30
X42 L290MB 290 - 440 415 - 760 21 0.40 4 30
X46 320 - 525 435 - 760 20 0.41 4 22
X52 L360MB 360 - 510 460 - 760 20 0.41 4 22
X56 390 - 545 490 - 760 18 0.42 4 22
X60 L415MB 415 - 565 520 - 760 18 0.42 4 22
X65 L450MB 450 - 570 535 - 760 18 0.43 4 22
X70 L485MB 485 - 605 570 - 760 18 0.43 4 22
PLATES FOR PIPES ACCORDING TO API 5L 1) AND EN 10208-2 1) ( SOUR SERVICE 4) )
Grade acc. API-5L Designation acc. EN 10208-2
Yield Strength Rt0,5 (Rt0,2) 2) [MPa]
TensileStrength Rm 2) [MPa]
Min. Elongation 2) [%] CEV max.2) Dimension
Table No.
Max. Thickness 3)
[mm]
B L245MB 245 - 440 415 - 760 22 0.40 4 30
X42 L290MB 290 - 440 415 - 760 21 0.40 4 30
X46 320 - 525 435 - 760 20 0.41 4 22
X52 L360MB 360 - 510 460 - 760 20 0.41 4 22
X60 L415MB 415 - 565 520 - 760 18 0.42 4 22
X65 L450MB 450 - 570 535 - 760 18 0.43 4 22
1) Standards API 5L and EN 10208 are technical conditions for supplies of welded pipes, not for plates 2) Informative value 3) Higher thickness on agreement 4) Supplied with HIC and SSC tests as per NACE or EN standard
12
Plates for ship building
Plates
PLATES ACCORDING TO INDIVIDUAL SHIPPING COMPANIES
Plates of structural steel grades according to the requirements of the inspection companies ABS, BV, DNV, LR, and others, with a min. yield strength 235 to 355 MPa, are used for ship and watercraft construction. Quality of this assortment is guaranteed by product approbations awarded by individual shipping companies.
Stee
l Gro
up
Min
. Yi
eld
Stre
ngth
ReH
[M
Pa]
Min
. Im
pact
Ene
rgy
KV
[°C/
J] –
long
itudi
nal
ABS
– Am
erica
n Bu
reau
of S
hipp
ing
BV –
Bur
eau
Verit
as
ČLPR
– C
zech
Shi
ppin
g an
d In
dust
rial r
egist
er
GL
– G
erm
anisc
her L
loyd
DNV
– De
t Nor
ske
Verit
as
LR –
Lio
yd's
Reg
ister
of
Shi
ppin
g
RIN
A –
Regi
stro
Ital
iano
Nav
ale
PC –
Mor
skoj
Reg
istr
Sudo
chod
stva
Dim
ensio
n Ta
ble
No.
Nor
mal
Stre
ngth
Stee
l Gra
des
235
– A A A A A A A/24 A 1
0/27 B B B B B B S/24 B 1
-20/27 D D D D D D SS/24 D 1
-40/27 E E E E E E E/24 E 1
High
Stre
ngth
St
eel G
rade
s
315
0/31 AH 32 AH 32 A 32 A 32 A 32 AH 32 S/32 A 32 1
-20/31 DH 32 DH 32 D 32 D 32 D 32 DH 32 SS/32 D 32 1
-40/31 EH 32 EH 32 E 32 E 32 E 32 EH 32 E/32 E 32 1
355
0/34 AH 36 AH 36 A 36 A 36 A 36 AH 36 S/36 A 36 1
-20/34 DH 36 DH 36 D 36 D 36 D 36 DH 36 SS/36 D 36 1
-40/34 EH 36 EH 36 E 36 E 36 E 36 EH 36 E/36 E 36 1
Maximum value of the carbon equivalent as per the formula on agreement
13
Plates for ship building
PLATES ACCORDING TO ASTM A 131
Designation GradeMin. Yield Strength[MPa]
TensileStrength Rm
[MPa]
Min. Elongation200/50
[%]
Min. ImpactEnergy KV 1)
[°C/J] – longitudinal
DimensionTable No.
Max. Thickness
[mm]
A131
A 235 400–520 21/24 +20/27 1 80
B 235 400–520 21/24 0/27 1 80
D 235 400–520 21/24 -20/27 1 80
E 235 400–520 21/24 -40/27 1 80
AH 32 315 440–590 19/22 0/31 1 80
DH 32 315 440–590 19/22 -20/31 1 80
EH 32 315 440–590 19/22 -40/31 1 80
AH 36 355 490–620 19/22 0/34 1 80
DH 36 355 490–620 19/22 -20/34 1 80
EH 36 355 490–620 19/22 -40/34 1 80
Maximum value of the carbon equivalent as per the formula on agreement1) Valid for thickness up to 50 mm, for higher thickness refer to the standard
14
Hot-rolled plates for cold forming
Plates
THERMOMECHANICAL ROLLED PLATES OF STEELS ACCORDING TO EN 10149-2
Standard methods used for processing these plates are bending, fl anging, cold roll forming, etc. Based on agreement these plates can be delivered in the condition suitable for hot-dip zinc-coating. These plates have excellent weldability because of low carbon equivalent.
DesignationMin. Yield
Strength ReH [MPa]
Tensile Strength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV 1)
[°C/J] – longitudinal
TransverseBend Test 2)
DimensionTable No.
Max. Thickness
[mm]
S315MC 315 390–510 24 -20/40 0 t 3 20 3)
S355MC 355 430–550 23 -20/40 0.5 t 3 20 3)
S420MC 420 480–620 19 -20/40 0.5 t 3 20 3)
S460MC 460 520–670 17 -20/40 1 t 3 20 3)
S500MC 500 550–700 14 -20/40 1 t 3 16 3)
S550MC 550 600–760 14 -20/40 1.5 t 3 16 3)
Maximum value of the carbon equivalent as per the formula on agreement1) Testing on agreement 2) Minimum former diameter for 180° bend angle; t – plate thickness3) Under standard
EQUIVALENT DESIGNATION
EN 10149-2 SEW 092
S315MC (QStE 340 TM)
S355MC (QStE 380 TM)
S420MC QStE 420 TM
S460MC QStE 460 TM
S500MC QStE 500 TM
S550MC QStE 550 TM
15
Hot-rolled plates for cold forming
NORMALIZED PLATES OF STEELS ACCORDING TO EN 10149-3
These plates guarantee suitability for cold forming because of their technological processing. Standard methods used for processing these plates are bending, fl anging, cold roll forming, etc. Based on agreement these plates can be delivered in the condition suitable for hot-dip zinc-coating.
DesignationMin. Yield
Strength ReH[MPa]
Tensile Strength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV 1)
[°C/J] – longitudinal
TransverseBend Test 2)
DimensionTable No.
Max. Thickness
[mm]
S260NC 260 370–490 30 -20/40 0 t 1 20 3)
S315NC 315 430–550 27 -20/40 0.5 t 1 20 3)
S355NC 355 470–610 25 -20/40 0.5 t 1 20 3)
S420NC 420 530–670 23 -20/40 0.5 t 2 20 3)
Maximum value of the carbon equivalent as per the formula on agreement1) Testing on agreement 2) Minimum former diameter for 180° bend angle; t – plate thickness3) Under standard
EQUIVALENT DESIGNATION
EN 10149-3 SEW 092
S260NC QStE 260N
S315NC (QStE 340N)
S355NC (QStE 380N)
S420NC QStE 420N
16
Plates
QUENCHED AND TEMPERED PLATES OF 500 Q AND 690 Q STEEL GRADES
Quenched and tempered plates of 500 Q and 690 Q steel grades are supplied in the form suitable for steel structures (S500 …, S690 …) as per EN 10025-6 or in the form suitable for pressure vessels (P500…, P690…) as per EN 10028-6.
Designation as per EN 10025-6: S500 Q, S500 QL, S500 QL1, S690 Q, S690 QL, S690 QL1.Designation as per EN 10028-6: P500 Q, P500 QH, P500 QL1, P500 QL2, P690 Q, P690 QH, P690 QL1, P690 QL2.
PARAMETERS FOR PLATES PURCHASE ORDER
Thickness 20–80 mm
Width 1) 1500–2500 mm
Length max. 11000 mm 2)
Weight of one piece of plate max. 8000 kg
Total volume of plates ordered multiples of 50 t
1) Higher or lower width on agreement2) For thickness 20–25 mm (incl.) only max. 8000 mm
MECHANICAL PROPERTIES AND CARBON EQUIVALENT
DesignationMin. Yield
Strength ReH 1) [MPa]
Min. YieldStrength Rp0.2 2)
[MPa]
Tensile Strength Rm 1)
[MPa]
Min. Elongation (L0=5.65√S0)
[%]
Min. Impact Energy KV 3)
[°C/J] – transverseCEV max. 4)
S500 Q 500 – 590–770 17 -20/27 0.47
S500 QL 500 – 590–770 17 -40/27 0.47
S500 QL1 500 – 590–770 17 -60/27 0.47
P500 Q 500 – 590–770 17 -20/27 –
P500 QH 500 380 590–770 17 -20/27 –
P500 QL1 500 380 590–770 17 -40/27 –
P500 QL2 500 380 590–770 17 -60/27 –
S690 Q 690 – 770–940 14 -20/27 0.65
S690 QL 690 – 770–940 14 -40/27 0.65
S690 QL1 690 – 770–940 14 -60/27 0.65
P690 Q 690 – 770–940 14 -20/27 –
P690 QH 690 570 770–940 14 -20/27 –
P690 QL1 690 570 770–940 14 -40/27 –
P690 QL2 690 570 770–940 14 -60/27 –
1) Valid for thickness up to 50 mm, for higher thickness refer to the standard 2) Testing on agreement; valid for temperature 300 °C and thickness up to 50 mm; for other temperatures (lower)
or higher thickness refer to the standard EN 10028-63) For other temperatures (higher) under standard refer to the standard 4) ; only for plates supplied as per EN 10025-6; valid for thickness up to 50 mm;
for higher thickness refer to the standard EN 10025-6
Quenched and tempered plates
17
Plates of non alloy or alloy steels for quenching and tempering
PLATES OF STEELS ACCORDING TO EN 10083-2 AND EN 10083-3
They are used for machinery parts in all machinery production areas. These plates are diffi cult for welding in most cases. They are supplied with out heat treatment or in soft annealed (+A) or normalized (+N) condition according to the following table. Products of these plates are further processed with heat treatment (usually quenching and tempering), after such treatment they obtain their typical properties, i.e. high toughness, hardness and strength.
DesignationMin. Yield
Strength ReH 1)
[MPa]
Min. Tensile Strength Rm 1)
[MPa]
Min. Elongation 1) (L0 = 5.65√S0)
[%]
HB max.(+A)
DimensionTable No.
Max. Thickness
[mm]
C22E 2) 240 430 24 – 1 80C35/C35E 2) 300 550 18 – 2 80C40/C40E 2) 320 580 16 – 2 80C45/C45E 2) 340 620 14 207 2 80
C50E 2) 355 650 13 217 2 80C55/C55E 2) 370 680 11 229 2 80C60/C60E 2) 380 710 10 241 2 80
28Mn6 2) 345 630 17 223 2 8038Cr2 3) – – – 207 2 8046Cr2 3) – – – 223 2 8034Cr4 3) – – – 223 2 8037Cr4 3) – – – 235 2 8041Cr4 3) – – – 241 2 80
25CrMo4 3) – – – 212 2 8034CrMo4 3) – – – 223 2 8042CrMo4 3) – – – 241 2 8050CrMo4 3) – – – 248 2 80
34CrNiMo6 3) – – – 248 2 8030CrNiMo8 3) – – – 248 2 80
35NiCr6 3) – – – 223 2 8039NiCrMo3 3) – – – 240 2 80
51CrV4 3) – – – 248 2 8020MnB5 3) 4) – – – – 2 8030MnB5 3) 4) – – – – 2 8038MnB5 3) 4) – – – – 2 80
27MnCrB5-2 3) 4) – – – – 2 8033MnCrB5-2 3) 4) – – – – 2 8039MnCrB6-2 3) 4) – – – – 2 80
1) Valid for plates in normalized condition and for thickness up to 16 mm, for higher thickness refer to the standard2) EN 10083-23) EN 10083-34) Plates without heat treatment
EQUIVALENT DESIGNATION
EN 10083-2,-3 Germany Great Britain
C22E CK22 070M20C35/C35E C35/CK35 080M36C40/C40E C40/CK40 080M40C45/C45E C45/CK45 080M46
C50E CK50 080M50C55/C55E C55/CK55 070M55C60/C60E C60/CK60 070M60
28Mn6 28Mn6 150M1938Cr2 38Cr2 –46Cr2 46Cr2 –
EN 10083-2,-3 Germany Great Britain
34Cr4 34Cr4 530M3237Cr4 37Cr4 530M3641Cr4 41Cr4 530M40
25CrMo4 25CrMo4 708M2534CrMo4 34CrMo4 708M3242CrMo4 42CrMo4 708M4050CrMo4 50CrMo4 708M50
34CrNiMo6 34CrNiMo6 817M4030CrNiMo8 30CrNiMo8 823M30
35NiCr6 35NiCr6 –
18
Plates of non alloy or alloy steels for quenching and tempering
Plates
Designation Grade(SAE Number)
Dimension table
number
A 827
1009 1
1020 1
1035 2
1040 2
1045 2
1050 2
A 829
1330 2
1335 2
1340 2
1345 2
4118 2
4130 2
4135 2
4137 2
4140 2
4142 2
4145 2
4150 2
4340 2
4615 2
4617 2
4620 2
8615 2
8617 2
9620 2
8622 2
8625 2
8627 2
8630 2
8637 2
8640 2
8742 2
Heat treatment and mechanical properties on agreement.
PLATES OF STEELS ACCORDING TO ASTM A 827, A 829, A 830
Designation Grade(SAE Number)
Dimension table
number
A 830
1006 1
1008 1
1009 1
1010 1
1012 1
1015 1
1016 1
1017 1
1018 1
1019 1
1020 1
1021 1
1022 1
1023 1
1025 1
1026 1
1030 1
1033 1
1035 2
1037 2
1038 2
1039 2
1040 2
1042 2
1043 2
1045 2
1046 2
1049 2
1050 2
1055 2
1060 2
1524 2
1527 2
1536 2
1541 2
1548 2
1552 2
19
PLATES OF STEELS ACCORDING TO EN 10084
These plates are supplied only in soft annealed (+A) condition.
Designation HB max.(+A)
DimensionTable No.
Max. Thickness
[mm]
C10E 131 1 80C15E 143 1 80C16E 156 1 8017Cr3 174 1 8028Cr4 217 2 80
16MnCr5 207 2 8016MnCrB5 207 2 8020MnCr5 217 2 8018CrMo4 207 2 8020MoCr3 217 2 8020MoCr4 207 2 8016NiCr4 217 2 80
10NiCr5-4 192 2 8018NiCr5-4 223 2 8017CrNi6-6 229 2 80
20NiCrMo2-2 212 2 8017NiCrMo6-4 229 2 8018CrNiMo7-6 229 2 80
Plates of case hardening steels
20
Plates of nitriding steels
PLATES OF STEELS ACCORDING TO EN 10085
These plates are supplied only in soft annealed (+A) condition.
Designation HB max.(+A)
DimensionTable No.
Thickness 1)
[mm]
24CrMo13-6 248 2 20–8031CrMo12 248 2 20–8031CrMoV9 248 2 20–80
33CrMoV12-9 248 2 20–80
1) Other thickness on agreement
21
PLATES OF STEELS ACCORDING TO EN ISO 4957
These plates are supplied only in soft annealed (+A) condition.
Designation HB max.(+A)
DimensionTable No.
Thickness 1)
[mm]
C45U 207 2 10–80C70U 183 2 20–80C80U 192 2 20–80C90U 207 2 20–80
21MnCr5 217 2 20–8070MnMoCr8 248 2 20–8090MnCrV8 229 2 20–8035CrMo7 260 2 20–80
40CrMnNiMo8-6-4 260 2 20–8055NiCrMoV7 248 2 20–80
1) Other thickness on agreement
Plates of tool steels
22
Plates
PLATES OF STEELS FOR SIMPLE PRESSURE VESSELS ACCORDING TO EN 10207
Plates with low yield strength for simple pressure vessels and storage facilities operating under normal outdoor temperatures, e.g. for compressed air or other fl uids.
DesignationMin. Yield
Strength ReH 1)
[MPa]
Min. Yield Strength Rp0.2 2)
[MPa]
TensileStrength Rm
[MPa]
Min. Elongation(L0 = 5.65√S0)
[%]
Min. Impact Energy KV
[°C/J] – longitudinal
DimensionTable No.
Max. Thickness
[mm]
P235S 235 117 360–480 26 -20/28 1 60 3)
P265S 265 140 410–530 22 -20/28 1 60 3)
P275SL 275 132 390–510 24 -50/28 1 60 3)
1) Valid for thickness up to 16 mm, for higher thickness refer to the standard 2) Valid for temperature 300 °C, for other temperatures (lower) under standard refer to the standard3) Under standard
Plates of steels for pressure vessels
23
Plates of steels for pressure vessels
PLATES OF STEELS ACCORDING TO EN 10028-2
Plates of unalloyed as well as alloyed steels for pressure loaded vessels and facilities, operating under normal as well as elevated tempera-tures. These plates are usually delivered in normalized condition or in normalized and tempered condition.
Designation Min. Yield
Strength ReH 1)
[MPa]
Min. Yield Strength Rp0,2 2)
[MPa]
TensileStrength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV 3)
[°C/J] – transverse
DimensionTable No.
Max. Thickness
[mm]
P235GH 4) 235 153 360–480 24 -20/27 1 80 5)
P265GH 4) 265 173 410–530 22 -20/27 1 80 5)
P295GH 4) 295 192 460–580 21 -20/27 1 80 5)
P355GH 4) 355 232 510–650 20 -20/27 1 80 5)
16Mo3 275 194 440–590 22 +20/31 1 80
18MnMo4-5 345 285 510–650 20 -20/27 1 80
15NiCuMoNb5-6-4 460 380 610–780 16 -20/27 2 80
13CrMo4-5 300 216 450–600 19 +20/31 1 80
13CrMoSi5-5 310 233 510–690 20 0/27 1 80
10CrMo9-10 310 236 480–630 18 +20/31 1 80
12CrMo9-10 355 295 540–690 18 -20/27 2 80
1) Valid for thickness up to 16 mm, for higher thickness refer to the standard 2) Testing on agreement; valid for temperature 300 °C and thickness up to 16 mm; for other temperatures under standard or higher thickness refer
to the standard 3) For other temperatures under standard refer to the standard or on agreement4) Maximum value of the carbon equivalent as per the formula on agreement5) Higher thickness up to 100 mm on agreement
EQUIVALENT DESIGNATION
EN 10028-2 DIN 17155
P235 GH H I
P265 GH H II
P295 GH 17Mn4
P355 GH 19Mn6
16Mo3 15Mo3
13CrMo4-5 13CrMo44
10CrMo9-10 10CrMo910
18MnMo4-5 –
24
Plates of steels for pressure vessels
Plates
PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10028-3
These steels feature guaranteed fi ne-grain structure and low carbon equivalent. Mechanical properties of these plates are guaranteed at high temperatures (up to 400 °C) – yield strength Rp0,2 as well as at low temperatures (down to -50 °C) – impact energy KV; therefore, they can be used for constructions of more demanding pressure vessels working under high as well as low temperatures.
DesignationMin. Yield
Strength ReH 1)
[MPa]
Min. YieldStrength Rp0.2 2)
[MPa]
Tensile Strength Rm
[MPa]
Min. Elongation(L0 = 5.65√S0)
[%]
Min. ImpactEnergy KV 3)
[°C/J] – transverseCEV max. 4) Dimension
Table No.
Max. Thickness
[mm]
P275NH 275 179 390–510 24 -20/30 0.40 1 80 5)
P275NL1 275 179 390–510 24 -40/27 0.40 1 80 5)
P275NL2 275 179 390–510 24 -50/27 0.40 1 80 5)
P355N 355 – 490–630 22 -20/30 0.43 1 80 5)
P355NH 355 232 490–630 22 -20/30 0.43 1 80 5)
P355NL1 355 232 490–630 22 -40/27 0.43 1 80 5)
P355NL2 355 232 490–630 22 -50/27 0.43 1 80 5)
P460NH 460 300 570–720 17 -20/30 0.53 2 80
P460NL1 460 300 570–720 17 -40/27 0.53 2 80
P460NL2 460 300 570–720 17 -50/27 0.53 2 80
1) Valid for thickness up to 16 mm, for higher thickness refer to the standard2) Testing on agreement; valid for temperature 300 °C and thickness up to 16 mm, for other temperatures under standard or higher thickness refer
to the standard3) For other temperatures under standard refer to the standard4) On agreement; ; valid for thickness up to 60 mm, for higher thickness refer to the standard5) Higher thickness up to 100 mm on agreement
EQUIVALENT DESIGNATION
EN 10028-3 DIN 17102
P275NH WStE 285
P275NL1 TStE 285
P275NL2 EStE 285
P355N StE 355
P355NH WStE 355
P355NL1 TStE 355
P355NL2 EStE 355
P460NH WStE 460
P460NL1 TStE 460
P460NL2 EStE 460
25
Plates of steels for pressure vessels
THERMOMECHANICAL ROLLED PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10028-5
Thermomechanical rolled plates having higher min. yield strength up to 460 MPa are designed for pressure vessels and facilities working under normal or low temperatures. These plates have excellent weldability because of low carbon equivalent. Impact energy is guaranteed even at temperature -50 °C.
DesignationMin. Yield
Strength ReH[MPa]
TensileStrength Rm
[MPa]
Min. Elongation (L0 = 5.65√S0)
[%]
Min. Impact Energy KV 3)
[°C/J] – transverseCEV max. 4) Dimension
Table No.
Max. Thickness
[mm]
P355M 355 1) 450–610 22 -20/27 0.39 3 40
P355ML1 355 1) 450–610 22 -40/27 0.39 3 40
P355ML2 355 1) 450–610 22 -50/27 0.39 3 40
P420M 420 2) 500–660 19 -20/27 0.43 3 30 5)
P420ML1 420 2) 500–660 19 -40/27 0.43 3 30 5)
P420ML2 420 2) 500–660 19 -50/27 0.43 3 30 5)
P460M 460 2) 530–720 17 -20/27 0.45 3 22 5)
P460ML1 460 2) 530–720 17 -40/27 0.45 3 22 5)
P460ML2 460 2) 530–720 17 -50/27 0.45 3 22 5)
1) Valid for thickness up to 40 mm, for higher thickness refer to the standard2) Valid for thickness up to 16 mm, for higher thickness refer to the standard3) For other temperatures under standard refer to the standard4) On agreement; ; valid for thickness up to 16 mm, for higher thickness refer to the standard5) Higher thickness on agreement
26
Plates of steels for pressure vessels
Plates
PLATES OF STEELS ACCORDING TO ASTM/ASME
Designation GradeMin. Yield Strength [MPa]
TensileStrength Rm
[MPa]
Min. Elongation200/50
[%]
Min. Impact Energy KV 1)
[°C/J] – longitudinal
DimensionTable No.
Max. Thickness
[mm]
A/SA 204A 255 450–585 19/23 2) 1 80B 275 485–620 17/21 2) 1 80C 295 515–655 16/20 2) 1 80
A/SA 285A 165 310–450 27/30 4/14 1 50 3)
B 185 345–485 25/28 10/14 1 50 3)
C 205 380–515 23/27 16/14 1 50 3)
A/SA 387
2 310 485–620 18/22 2) 1 8011 310 515–690 18/22 2) 1 8012 275 450–585 19/22 2) 1 8022 310 515–690 –/18 2) 1 80
A/SA 455 260 515–655 15/22 -4/18 1 20 3)
A/SA 51560 (415) 220 415–550 21/25 2) 1 80 4)
65 (450) 240 450–585 19/23 2) 1 80 4)
70 (485) 260 485–620 17/21 2) 1 80 4)
On agreement, carbon equivalent guarantee is available as per the formula 1) Testing on agreement2) Testing temperature and minimum impact energy on agreement3) Under standard4) Higher thickness up to 100 mm on agreement
PLATES OF FINE-GRAIN STEELS ACCORDING TO ASTM/ASME
Designation GradeMin. Yield Strength [MPa]
TensileStrength Rm
[MPa]
Min. Elongation 200/50
[%]
Min. Impact Energy KV 1)
[°C/J] – longitudinal
DimensionTable No.
Max. Thickness
[mm]
A/SA 299A 290 4) 515–655 16/19 -7/20 1 80B 325 4) 550–690 16/19 -7/20 2 80
A/SA 302
A 310 515–655 15/19 2) 1 80B 345 550–690 15/18 2) 2 80C 345 550–690 17/20 2) 2 80D 345 550–690 17/20 2) 2 80
A/SA 516
55 (380) 205 380–515 23/27 -51/18 1 80 5)
60 (415) 220 415–550 21/25 -51/18 1 80 5)
65 (450) 240 450–585 19/23 -51/18 1 80 5)
70 (485) 260 485–620 17/21 -46/20 1 80 5)
A/SA 537 class 1 345 485–620 18/22 -62/20 1 80A/SA 612 345 570–725 16/22 -46/27 2 25 3)
A/SA 662A 275 400–540 20/23 -60/18 1 50 3)
B 275 450–585 20/23 -51/18 1 50 3)
C 295 485–620 18/22 -46/20 1 50 3)
A/SA 737B 345 485–620 18/23 2) 1 80C 415 550–690 18/23 2) 2 80
On agreement, carbon equivalent guarantee is available as per the formula 1) Testing on agreement2) Testing temperature and minimum impact energy on agreement3) Under standard4) Valid for thickness up to 25 mm, for higher thickness refer to the standard5) Higher thickness up to 100 mm on agreement
27
Delivery conditions
APPLICABLE STANDARDS
Dimension, fl atness EN 10029, A(SA)20/A(SA)20M, A(SA)6/A(SA)6M
Surface EN 10163
Ultrasound EN 10160, SEL 072/77, A(SA)435, A(SA)578, other standards on agreement
Certifi cates EN 10204
Testing as per EN, ASTM, ASME, shipping company standards, other standards on agreement
INTERNAL SOUNDNESS HOMOGENEITY ULTRASONIC TESTING
Automatic ultrasonic TÜV NORD certifi ed line is used or manual testing is available to meet stricter conditions.
28
QUALITY ASSURANCE CERTIFICATES AS PER EN 10204 : 2004
Quality Assurance certifi cates shall be issued by the Quality Assurance Department stating chemical composition of heat and material testing results (e.g. ultrasound, mechanical testing) as required by the customer:
Customer Order Compliance Declaration “2.1”The document is issued by the manufacturer to certify that the products delivered comply with customer order requirements. The document does not state any test results.
Testing Protocol “2.2”The document is issued by the manufacturer to certify that products delivered comply with customer order requirements. The document states general test results.
Inspection Certificate “3.1”This is a document issued by the manufacturer in which the manufacturer confi rms that the products supplied are in line with the requirements of the order and in which the manufacturer indicates the results of the tests.The testing unit and the tests executed are indicated in the product’s specifi cation, in the offi cial specifi cations, in the corresponding technical specifi cations and/or in the order.The document is confi rmed by an authorized representative of the manufacturer independent of the production units.In the Inspection Certifi cate “3.1”, the manufacturer may indicate the results of tests obtained from testing as specifi ed by the specifi cation on the basic materials or input products used on condition that the manufacturer uses tracing procedures and can provide the necessary corresponding inspection documents.
Inspection Certificate “3.2”This is a document prepared by an authorized representative of the manufacturer independent of the production units and either by an authorized representative of the client (inspection company) or by an inspector indicated in the offi cial specifi cations in which they declare that the products supplied are in line with the requirements of the order and which indicates the results of the tests.In the Inspection Certifi cate “3.2”, the manufacturer may indicate the results of tests obtained from testing as specifi ed by the specifi cation on the basic materials or input products used on condition that the manufacturer uses tracing procedures and can provide the necessary corresponding inspection documents.
Inspection Companiesa) national: ŘJ, ČD, ZVS, INSPEKTA, ČLPR, and othersb) international: LR, DNV, ABS, BV, GL, TÜV, RINA, Russian Naval Register of Shipping, and othersc) inspection carried out directly by the customer
Multiple certifi cation available on agreement.
Material certificates
Plates
29
Product marking is performed by stamping and painting. A punch for stamping in cold condition is used for marking of plates (Four-High Mill) in low-stress spot method. Manual low-stress stamping (Two-High Mill) the low-stress method has to be agreed in the order. White paint marking is carried out with automatic marking machines, or manually (usually using templates). In case of any specifi c customer‘s requirement for a special plate marking, either in the form of a text (sprayed with white color on the plate), or in the form of color marking, marking is carried out within the frame of each individual order based on agreement. The “Colour Marking Catalogue” containing individual patterns is available to make the color marking easier.
EXAMPLE OF PLATE MARKING WITH COLD STAMPING
EXAMPLE OF PLATE MARKING WITH COLOUR
Rolled product No. Plate serial No. from the rolled product Manufacturer’s symbol Heat origin Heat No.
Steel grade (and/or heat treatment code) Sample No.
Plate widthRolled product No. Heat origin Heat no. Plate serial No. from the rolled product
Internal localization code
Heat treatmentcode
Order No.
Plate thickness
Steel grade
Inspection Plate length
Marking of plates
width [mm] thickness [mm]
1 001 1 101 1 251 1 301 1 401 1 501 1 601 1 701 1 801 1 901 2 001
1 000 1 100 1 250 1 300 1 400 1 500 1 600 1 700 1 800 1 900 2 000 2 100
5 12 10 10 12 12 12 12 12
6 12 12 12 10 10 10 12 12 12 12 12 12
7 14 14 14 14 14 14 14 14 14 14 14 14
8 15 15 15 15 15 15 15 15 15 15 15 15
9 16 16 16 16 16 16 16 16 16 16 16 16
10 16 16 16 16 16 16 16 16 16 16 16 16
11 16 16 16 16 16 16 16 16 16 16 16 16
12 16 16 16 16 16 16 16 16 16 16 16 16
13 16 16 16 16 16 16 16 16 16 16 16 16
14 16 16 16 16 16 16 16 16 16 16 16 16
15 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 16
17 16 16 16 16 16 16 16 16 16 16 16 16
18 16 16 16 16 16 16 16 16 16 16 16 16
19 16 16 16 16 16 16 16 16 16 16 16 16
20 16 16 16 16 16 16 16 16 16 16 16 16
21 16 16 16 16 16 16 16 16 16 16 16 16
22 16 16 16 16 16 16 16 16 16 16 16 16
23 16 16 16 16 16 16 16 16 16 16 16 16
24 16 16 16 16 16 16 16 16 16 16 16 16
25 16 16 16 16 16 16 16 16 16 16 16 16
26 16 16 16 16 16 16 16 16 16 16 16 16
28 16 16 16 16 16 16 16 16 16 16 16 16
30 16 16 16 16 16 16 16 16 16 16 16 16
32 16 16 16 16 16 16 16 16 16 16 16 15
34 16 16 15 16 16 16 16 16 16 16 15 14
36 16 16 15 16 16 16 16 16 16 15 14 13
38 16 16 14 16 16 15 16 16 15 14 13 12
40 16 15 13 16 15 14 16 15 14 13 12 12
42 16 14 12 16 14 13 15 14 13 12 12 11
44 15 13 12 15 14 13 14 13 13 12 11 11
46 14 13 11 14 13 12 14 13 12 11 11 10
48 14 12 11 14 13 12 13 12 11 11 10 10
50 13 12 10 13 12 11 12 12 11 10 10 9
52 12 11 10 12 11 11 12 11 10 10 9 9
54 12 11 9 12 11 10 11 11 10 9 9 8
56 11 10 9 11 11 10 11 10 10 9 9 8
58 11 10 9 11 10 9 11 10 9 9 8 8
60 11 10 8 11 10 9 10 9 9 8 8 7
65 10 9 8 10 9 8 9 9 8 8 7 7
70 9 8 7 9 8 8 9 8 7 7 7 6
75 8 7 6 8 8 7 8 7 7 7 6 6
80 8 7 6 8 7 7 7 7 6 6 6 5
Other plate dimensions on agreement
TABLE 1 – MAXIMUM AVAILABLE PLATES LENGTH [m] FOR STEELS WITH MINIMUM TENSILE STRENGTH Rm up to 530 MPa
31
2 101 2 201 2 301 2 401 2 501 2 601 2 701 2 801 2 901 3 001 3 101 3 201 width [mm]thickness [mm]2 200 2 300 2 400 2 500 2 600 2 700 2 800 2 900 3 000 3 100 3 200 3 300
10 10 10 10 10 5
12 12 12 12 12 10 10 10 10 6
14 14 14 14 14 13 13 12 12 7
15 15 15 15 15 15 15 15 15 15 8
16 16 16 16 16 16 16 16 16 16 16 16 9
16 16 16 16 16 16 16 16 16 16 16 16 10
16 16 16 16 16 16 16 16 16 16 16 16 11
16 16 16 16 16 16 16 16 16 16 16 16 12
16 16 16 16 16 16 16 16 16 16 16 16 13
16 16 16 16 16 16 16 16 16 16 16 16 14
16 16 16 16 16 16 16 16 16 16 16 16 15
16 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 17
16 16 16 16 16 16 16 16 16 16 16 16 18
16 16 16 16 16 16 16 16 16 16 16 16 19
16 16 16 16 16 16 16 16 16 16 16 15 20
16 16 16 16 16 16 16 16 16 15 15 14 21
16 16 16 16 16 16 16 16 15 15 14 14 22
16 16 16 16 16 16 16 15 15 14 14 13 23
16 16 16 16 16 16 15 14 14 13 13 13 24
16 16 16 16 15 15 14 14 13 13 12 12 25
16 16 16 15 15 14 14 13 13 12 12 11 26
16 16 15 14 14 13 13 12 12 11 11 11 28
15 15 14 13 13 12 12 11 11 11 10 10 30
14 14 13 12 12 11 11 11 10 10 9 9 32
13 13 12 12 11 11 10 10 9 9 9 9 34
13 12 11 11 10 10 10 9 9 9 8 8 36
12 11 11 10 10 9 9 9 8 8 8 8 38
11 11 10 10 9 9 9 8 8 8 7 7 40
11 10 10 9 9 8 8 8 7 7 7 7 42
10 10 9 9 8 8 8 7 7 7 7 6 44
10 9 9 8 8 8 7 7 7 7 6 6 46
9 9 8 8 8 7 7 7 6 6 6 6 48
9 8 8 8 7 7 7 6 6 6 6 5 50
8 8 8 7 7 7 6 6 6 6 5 5 52
8 8 7 7 7 6 6 6 6 5 5 5 54
8 7 7 7 6 6 6 6 5 5 5 5 56
7 7 7 6 6 6 6 5 5 5 5 5 58
7 7 6 6 6 6 5 5 5 5 5 60
6 6 6 6 5 5 5 5 65
6 6 5 5 5 5 70
5 5 5 5 75
5 5 5 80
width [mm] thickness [mm]
1 001 1 101 1 251 1 301 1 401 1 501 1 601 1 701 1 801 1 901 2 001
1 000 1 100 1 250 1 300 1 400 1 500 1 600 1 700 1 800 1 900 2 000 2 100
5 10 10 10 10 10 10 10 10
6 12 12 12 10 10 10 12 12 12 12 12 12
7 12 12 12 14 14 14 14 14 14 14 14 14
8 14 14 14 14 14 14 14 14 14 14 14 14
9 15 16 16 16 16 16 16 16 16 16 16 16
10 16 16 16 16 16 16 16 16 16 16 16 16
11 16 16 16 16 16 16 16 16 16 16 16 16
12 16 16 16 16 16 16 16 16 16 16 16 16
13 16 16 16 16 16 16 16 16 16 16 16 16
14 16 16 16 16 16 16 16 16 16 16 16 16
15 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 16
17 16 16 16 16 16 16 16 16 16 16 16 16
18 16 16 16 16 16 16 16 16 16 16 16 16
19 16 16 16 16 16 16 16 16 16 16 16 16
20 16 16 16 16 16 16 16 16 16 16 16 16
21 16 16 16 16 16 16 16 16 16 16 16 16
22 16 16 16 16 16 16 16 16 16 16 16 16
23 16 16 16 16 16 16 16 16 16 16 16 16
24 16 16 16 16 16 16 16 16 16 16 16 16
25 16 16 16 16 16 16 16 16 16 16 16 16
26 16 16 16 16 16 16 16 16 16 16 16 16
28 16 16 16 16 16 16 16 16 16 16 16 16
30 16 16 16 16 16 16 16 16 16 16 16 16
32 16 16 16 16 16 16 16 16 16 16 16 15
34 16 16 15 16 16 16 16 16 16 16 15 14
36 16 16 15 16 16 16 16 16 16 15 14 13
38 16 16 14 16 16 15 16 16 15 14 13 12
40 16 15 13 16 15 14 16 15 14 13 12 12
42 16 14 12 16 14 13 15 14 13 12 12 11
44 15 13 12 15 14 13 14 13 13 12 11 11
46 14 13 11 14 13 12 14 13 12 11 11 10
48 14 12 11 14 13 12 13 12 11 11 10 10
50 13 12 10 13 12 11 12 12 11 10 10 9
52 12 11 10 12 11 11 12 11 10 10 9 9
54 12 11 9 12 11 10 11 11 10 9 9 8
56 11 10 9 11 11 10 11 10 10 9 9 8
58 11 10 9 11 10 9 11 10 9 9 8 8
60 11 10 8 11 10 9 10 9 9 8 8 7
65 10 9 8 10 9 8 9 9 8 8 7 7
70 9 8 7 9 8 8 9 8 7 7 7 6
75 8 7 6 8 8 7 8 7 7 7 6 6
80 8 7 6 8 7 7 7 7 6 6 6 5
Other plate dimensions on agreement
TABLE 2 – MAXIMUM AVAILABLE PLATES LENGTH [m] FOR STEELS WITH MINIMUM TENSILE STRENGTH Rm more than 530 MPa
33
2 101 2 201 2 301 2 401 2 501 2 601 2 701 2 801 2 901 3 001 3 101 3 201 width [mm]thickness [mm]2 200 2 300 2 400 2 500 2 600 2 700 2 800 2 900 3 000 3 100 3 200 3 300
10 10 10 10 10 5
12 12 12 12 12 10 10 10 10 6
14 14 14 12 12 10 10 10 10 7
14 14 14 14 14 13 13 13 13 12 8
16 16 16 14 14 13 13 13 13 12 12 12 9
16 16 16 16 16 16 16 16 16 16 16 16 10
16 16 16 16 16 16 16 16 16 16 16 16 11
16 16 16 16 16 16 16 16 16 16 16 16 12
16 16 16 16 16 16 16 16 16 16 16 16 13
16 16 16 16 16 16 16 16 16 16 16 16 14
16 16 16 16 16 16 16 16 16 16 16 16 15
16 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 17
16 16 16 16 16 16 16 16 16 16 16 16 18
16 16 16 16 16 16 16 16 16 16 16 16 19
16 16 16 16 16 16 16 16 16 16 16 15 20
16 16 16 16 16 16 16 16 16 15 15 14 21
16 16 16 16 16 16 16 16 15 15 14 14 22
16 16 16 16 16 16 16 15 15 14 14 13 23
16 16 16 16 16 16 15 14 14 13 13 13 24
16 16 16 16 15 15 14 14 13 13 12 12 25
16 16 16 15 15 14 14 13 13 12 12 11 26
16 16 15 14 14 13 13 12 12 11 11 11 28
15 15 14 13 13 12 12 11 11 11 10 10 30
14 14 13 12 12 11 11 11 10 10 9 9 32
13 13 12 12 11 11 10 10 9 9 9 9 34
13 12 11 11 10 10 10 9 9 9 8 8 36
12 11 11 10 10 9 9 9 8 8 8 8 38
11 11 10 10 9 9 9 8 8 8 7 7 40
11 10 10 9 9 8 8 8 7 7 7 7 42
10 10 9 9 8 8 8 7 7 7 7 6 44
10 9 9 8 8 8 7 7 7 7 6 6 46
9 9 8 8 8 7 7 7 6 6 6 6 48
9 8 8 8 7 7 7 6 6 6 6 5 50
8 8 8 7 7 7 6 6 6 6 5 5 52
8 8 7 7 7 6 6 6 6 5 5 5 54
8 7 7 7 6 6 6 6 5 5 5 5 56
7 7 7 6 6 6 6 5 5 5 5 5 58
7 7 6 6 6 6 5 5 5 5 5 60
6 6 6 6 5 5 5 5 65
6 6 5 5 5 5 70
5 5 5 5 75
5 5 5 80
34
TABLE 3 – MAXIMUM AVAILABLE PLATES LENGTH [m] FOR THERMOMECHANICAL ROLLED PLATES
width [mm] thickness [mm]
1 001 1 101 1 251 1 301 1 401 1 501 1 601 1 701 1 801 1 901 2 001
1 000 1 100 1 250 1 300 1 400 1 500 1 600 1 700 1 800 1 900 2 000 2 100
8 14 14 14 14 14 14 14 14 14 14 14 14
9 15 16 16 16 16 16 16 16 16 16 16 16
10 16 16 16 16 16 16 16 16 16 16 16 16
11 16 16 16 16 16 16 16 16 16 16 16 16
12 16 16 16 16 16 16 16 16 16 16 16 16
13 16 16 16 16 16 16 16 16 16 16 16 16
14 16 16 16 16 16 16 16 16 16 16 16 16
15 16 16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 16 16 16
17 16 16 16 16 16 16 16 16 16 16 16 16
18 16 16 16 16 16 16 16 16 16 16 16 16
19 16 16 16 16 16 16 16 16 16 16 16 16
20 16 16 16 16 16 16 16 16 16 16 16 16
21 16 16 16 16 16 16 16 16 16 16 16 16
22 16 16 16 16 16 16 16 16 16 16 16 16
23 16 16 16 16 16 16 16 16 16 16 16 16
24 16 16 16 16 16 16 16 16 16 16 16 16
25 16 16 16 16 16 16 16 16 16 16 16 16
26 16 16 16 16 16 16 16 16 16 16 16 16
28 16 16 16 16 16 16 16 16 16 16 16 16
30 16 16 16 16 16 16 16 16 16 16 16 16
32 16 16 16 16 16 16 16 16 16 16 16 15
34 16 16 15 16 16 16 16 16 16 16 15 14
36 16 16 15 16 16 16 16 16 16 15 14 13
38 16 16 14 16 16 15 16 16 15 14 13 12
40 16 15 13 16 15 14 16 15 14 13 12 12
Other plate dimensions on agreement
35
2 101 2 201 2 301 2 401 2 501 2 601 2 701 2 801 2 901 3001 width [mm]thickness [mm]2 200 2 300 2 400 2 500 2 600 2 700 2 800 2 900 3 000 3150
14 14 14 14 14 8
16 16 16 14 14 9
16 16 16 16 16 16 16 10
16 16 16 16 16 16 16 11
16 16 16 16 16 16 16 12
16 16 16 16 16 16 16 13
16 16 16 16 16 16 16 16 16 16 14
16 16 16 16 16 16 16 16 16 16 15
16 16 16 16 16 16 16 16 16 16 16
16 16 16 16 16 16 16 16 16 16 17
16 16 16 16 16 16 16 16 16 16 18
16 16 16 16 16 16 16 16 16 16 19
16 16 16 16 16 16 16 16 16 16 20
16 16 16 16 16 16 16 16 16 16 21
16 16 16 16 16 16 16 16 15 15 22
16 16 16 16 16 16 16 15 15 15 23
16 16 16 16 16 16 15 14 14 14 24
16 16 16 16 15 15 14 14 13 13 25
16 16 16 15 15 14 14 13 13 13 26
16 16 15 14 14 13 13 12 12 12 28
15 15 14 13 13 12 12 11 11 11 30
14 14 13 12 12 11 11 11 10 10 32
13 13 12 12 11 11 10 10 9 9 34
13 12 11 11 10 10 10 9 9 9 36
12 11 11 10 10 9 9 9 8 8 38
11 11 10 10 9 9 9 8 8 8 40
36
TABLE 4 – MAXIMUM AVAILABLE PLATES LENGTH [m] FOR THERMOMECHANICAL ROLLED PLATES FOR WELDED PIPES
width [mm] thickness [mm]
1 001 1 101 1 251 1 301 1 401 1 501 1 601 1 701 1 801 1 901 2 001 2 101
1 000 1 100 1 250 1 300 1 400 1 500 1 600 1 700 1 800 1 900 2 000 2 100 2 200
8 14 14 14 14 14 14 14 14 14 14 14 14 14
9 15 19 19 19 19 19 19 19 19 19 19 19 19
10 19 19 19 19 19 19 19 19 19 19 19 19 19
11 19 19 19 19 19 19 19 19 19 19 19 19 19
12 19 19 19 19 19 19 19 19 19 19 19 19 19
13 19 19 19 19 19 19 19 19 19 19 19 19 19
14 19 19 19 19 19 19 19 19 19 19 19 19 19
15 19 19 19 19 19 19 19 19 19 19 19 19 19
16 19 19 19 19 19 19 19 19 19 19 19 19 19
17 19 19 19 19 19 19 19 19 19 19 19 19 19
18 19 19 19 19 19 19 19 19 19 19 19 19 19
19 19 19 19 19 19 19 19 19 19 19 19 19 19
20 19 19 19 19 19 19 19 19 19 19 19 19 19
21 19 19 19 19 19 19 19 19 19 19 19 19 19
22 19 19 19 19 19 19 19 19 19 19 19 19 19
23 19 19 19 19 19 19 19 19 19 19 19 19 19
24 19 19 16 16 16 16 16 16 16 16 16 19 19
25 19 19 19 19 19 19 19 19 19 19 19 18 18
26 19 19 19 19 19 19 19 19 19 19 19 18 17
28 19 19 17 19 19 19 19 19 19 18 17 16 16
30 19 16 16 19 19 18 19 19 18 17 16 15 15
Other plate dimensions on agreement
37
2 201 2 301 2 401 2 501 2 601 2 701 2 801 2 901 3 001 3 101 3 201 width [mm]thickness [mm]2 300 2 400 2 500 2 600 2 700 2 800 2 900 3 000 3 100 3 200 3 300
14 14 14 14 8
19 19 14 14 9
19 19 19 19 19 19 10
19 19 19 19 19 19 11
19 19 19 19 19 19 14 14 14 14 14 12
19 19 19 19 19 19 14 14 14 14 14 13
19 19 19 19 19 19 19 19 19 19 19 14
19 19 19 19 19 19 19 19 19 19 19 15
19 19 19 19 19 19 19 19 19 19 18 16
19 19 19 19 19 19 19 19 18 18 17 17
19 19 19 19 19 19 19 18 17 17 16 18
19 19 19 19 19 18 18 17 16 16 15 19
19 19 19 19 18 17 17 16 15 15 15 20
19 19 18 18 17 16 16 15 15 14 14 21
19 18 18 17 16 16 15 15 14 14 13 22
18 18 17 16 16 15 14 14 13 13 13 23
18 17 16 15 15 14 14 13 13 12 12 24
17 16 15 15 15 14 13 13 12 12 12 25
16 15 15 14 14 13 13 12 12 11 11 26
15 14 14 13 13 12 12 11 11 11 10 28
14 13 13 12 12 11 11 11 10 10 10 30
38
Plates
Notes
EVRAZ VÍTKOVICE STEEL, a. s.
Headquarters: Štramberská 2871/47, 709 00 Ostrava-Hulváky, Czech Republic
Postal address: EVRAZ VÍTKOVICE STEEL, a. s., 706 02 Ostrava-Vítkovice, Czech Republic
Phone: +420 595 952 435, Fax: +420 595 952 144
E-mail: tradesteel@cz.evraz.com
Valid from: 9/2009
top related