instructor: yuntian zhu€¦ · – attendance expected (0.2% penalty for missing a quiz) reading...

NC State University Department of Materials Science and Engineering 1

MSE 791: Mechanical Properties of Nanostructured Materials Module 3: Fundamental Physics and Materials Design

Instructor: Yuntian Zhu Office: 308 RBII Ph: 513-0559

ytzhu@ncsu.edu

Lecture 1 Introduction, fcc, bcc and hcp crystal structures, partial

and full dislocations in fcc metals

NC State University Department of Materials Science and Engineering 2

Policies and Procedures see the Syllabus for more details

•  Attendance –  Attendance expected (0.2% penalty for missing a quiz)

Reading (textbook) Material: “Deformation Twinning in Nanocrystalline Materials,”Prog. Mater. Sci . 57, 1-62 (2012).

•  All HW are due in 1 week

NC State University Department of Materials Science and Engineering 3

Grading

•  Homework 9% •  Test 1 30% •  Test 2 30% •  Final 30%

No grade markup

NC State University Department of Materials Science and Engineering 4

Teaching style

•  Active student participation in class •  A dice will be rolled to determine who participates •  0.2% will be deducted if you are not present in the class to

answer a quiz; •  0.2% will be given if you give the right answer •  0.2% will be given to a volunteer who gives the right

answer •  No credit will be given or deducted if you give a wrong

answer.

NC State University

Quiz Coordinate

Department of Materials Science and Engineering 5

Cai, Shaobo, Fang, Xiaomeng, Ledfor, John Chris Lim, Mina Mahbooba, Zaynab M Rohrbaugh, Nathaniel W 1 2 3 4 5 6

NC State University

• A material can be strong or ductile, but rarely both at the same time

Nano-Ti

Nano-Cu

Valiev, Alexander, Zhu & Lowe, J. Mater. Res., 17 (2002) 5. Our work

• Good ductility is desired to prevent catastrophic failure

Youssef, Scattergood, Murty, Horton, Koch, APL, 87, 091904 (2005)

Strength and ductility of materials

NC State University

Only a few nanostructured materials show good ductility

The yielding strength is normalized by the yield strength of a material’s coarse-grained counterpart !

Issue: How do we obtain high ductility in nanostructured materials? !

Nanostructured materials have much higher strength than their coarse-grained counterparts!

Koch, Scripta Mater. 49 (2003) 657 !Zhu & Liao, Nature Mat., 3 (2004) 351.!

NC State University

fcc, bcc and hcp structures

Department of Materials Science and Engineering 8

hcp

http://www.youtube.com/watch?v=49qzoxACHfE fcc

NC State University

Dislocations

Department of Materials Science and Engineering 9

http://www.youtube.com/watch?v=iKKxTP6xp74 Dislocation cartoon http://www.youtube.com/watch?v=08a9hNFj22Y Cartepilar

Screw Dislocation

NC State University

Burgers Vector

Department of Materials Science and Engineering 10

•  Decide on the sense (vector) of dislocation line (arbitrary) •  Use “right-hand screw” to draw the Burgers circuit around the dislocation line •  Draw a Burgers circuit with equal length on each side; b = vector from the starting point

to ending point (see (a)) •  Or: Draw a closed Burgers circuit and then the circuit in a perfect crystal, b = vector from

the ending point to starting point in the perfect crystal circuit (see (b))

(a) (b)

NC State University

The Burgers Vectors are conserved

Department of Materials Science and Engineering 11

•  Each dislocation line can only have 1 Burger vector •  At a dislocation node where several dislocations meet, the

sum of Burgers vectors of dislocations going to the node equals the

•  A dislocation line cannot end inside a perfect crystal

NC State University

Dislocations in fcc metals

Department of Materials Science and Engineering 12

Define slip planes, full dislocations, and partial dislocations Definition of the Thompson tetrahedron

NC State University

Thompson Tetrahedron

Department of Materials Science and Engineering 13

Determine the Burgers vector of AB, BC and CD and partial dislocations on ABC plane Define stair-rod dislocation

NC State University

Homework (due in 1 week)

Department of Materials Science and Engineering 14

Lecture 1: #10 & 13