instruction manual honda ridgeline p-3000 · pdf filehonda ridgeline p-3000 aluminum upright...
Post on 17-Mar-2018
218 Views
Preview:
TRANSCRIPT
PART# DESCRIPTION QUANTITY ITEM
P101 DRIvER SIDE, FRONT 1
P102 PASSENgER SIDE, FRONT 1
P103 DRIvER SIDE, REAR 1
P104 PASENgER SIDE, REAR 1
SS-S111 3/8” X 3/4” SINglE SlIDER 8
S071 5/16” X 1 1/4” SINglE SlIDER 4
N015 5/16” PlASTIC kNOb lARgE 4
INSTRUCTION MANUALINSTRUCTION MANUAL
S111
S071
N015
W008
S111
R70 Driver Side bed Rail Adaptor
R71 Driver Side bed Rail Adaptor
HONDA RIDGELINE P-3000 ALUMINUM UPRIGHT & RAIL
PART# DESCRIPTION QUANTITY ITEM
SS-S101 3/8”” X 1” SINGLE SLIDER 4
SS-S103 3/8” X 3/4” DOUBLE SLIDER (3” SEPARATION) 4
W006 5/16” X 3/4” WASHER 1 TOOL
SS-W013 3/8” X 3/4” WASHER 16
SS-N006 3/8” NYLON NUT 16
N012 5/16” RIVET NUT 2
N020 5/16” RIVET NUT (TOOL) 1
N013 5/16” CAGE NUT 12 + 2 SPARE
B067 5/16” X 1 1/2” HEX BOLT 1 TOOL
SS-B165 5/16” COUNTER SUNK BOLT 14
R70 GEN 4 ADAPTOR PLATE DRIVER SIDE 1
R71 GEN 4 ADAPTOR PLATE PASSENGER SIDE 1
UPRIGHT MOUNT (GEN 4) (1 SET OF 4)
P013 ANGLE BRACE 4
A286-65/72 CROSS-BAR 65”OR 72” 2
Z286 END CAP 4
A20 ADJUSTABLE LADDER STOPPER 4
Flat Head Allen key
INSTRUCTION MANUALINSTRUCTION MANUALRIDGELINE P3000 Required Tools
1/2” Wrench
9/16” Wrench
Only tighten hardware when specified.
IHA
items not drawn to scale
Packaged: Checked: Date:
P111/112 P113/P114
OPTIONAl
OPTIONAl
OPTIONAl
P3309 65”
P3359 72”
black [ ]
Silver [ ]
IHA
Using a phillips head screw drive unscrew the factory bolt.
Pull the back the plastic bed rail 1” and then pull up gently to removed from vehicle.
Use a flat head screw driver and pop open the 2nd ridge from the rear.
1. 2. 3.
Use a 7/16” drill bit on the rear holes on the passenger and driver side bed rails.
7/16” drill bit
Optional Rivet Nut Installation (Drilling Required)
For additional strength you may use the optional anchor kit. Instructions are as follows.
9/16”
b067
W013
N012
N020
1/2”
Collapsing Anchor may become difficult.
keep Anchor tool stationary and tighen Hex bolt.
before screwing in the bolt apply a layer of silicon over anchor to prevent leaking.
Slide the cage nuts into the following locations. Repeat on passenger side.
5/16” bOlT
bED RAIl
N013
bED RAIl
To decrease the risk of losing a cage nut, screw in any 5/16” bolt for easier handling.
Remove the bolt when cage nut is fitted in bed rail.
4.
5.
7. 8.
6.
b165
N013
Position upright mount into their respective position and secure by tightening the Plastic knob.
Firmly secure allen bolts hardware.
S103
12. 13.
Insert for later stepsS103
S103
S101S101
10.
11.
W013
S103
N006
W008
W008
N005
N005
-After adjusting the cross bar and uprights to align correctly and centered Tightly secure all hardware.
-Due to truck bed’s tapering towards the tail light, it is not possible to adjust without loosening connections between cross bars & uprights.
14. 15.
A20
OR
16.
Z286
18.
19.
17.
Accessories | extruded Aluminum systems
Part # Description Color MSRP
A57 Adjustable Ladder Stopper 5-7” Black or White 35.00
AdjustAble lAdder stopper
Ì Adjustable 2pcs. ladder stopper prevents ladders from sliding forward.
Ì The bottom half of the stopper is galvanized and powder coated.
Ì The top is galvanized and rubber dipped for durability.
Ì The unit is bolted onto the bottom channels of the cross bar.
Part # Description Height Color MSRP
A64 Push to Secure 6-8” Black or White 69.00
push-2-secure
Ì Secure your ladder with the Vantech Push 2 Secure.
Ì System is bolted underneath cross bar. Holds ladder 6”-8” in height.
Ì Installs onto rear cross bar
Ì Works together with Ladder Stopper
Part # Height Bar Type Color MSRP
A20 5” A285, A286 Black Rubber 39.00 (pair)
A93 5” A270, A287, A613 Black Rubber 39.00 (pair)
AdjustAble Guides with eye hooks
Ì The adjustable guide slides inside the channels of the cross bar and locks into places with turn-knob
Ì Eyehook located on top for easy tie-down and bungee.
Ì 5” in height to secure item side to side.
rubber coAted side support
Ì Includes stainless steel mounting hardware.
Ì Built in Eyehook on each support
Part # Bar Type
Color MSRP
A08 A270 Black Rubber 15.00 pair
A04 A285 Black Rubber 17.00 pair
A03 A286 Black Rubber 19.00 pair
A04 A287 Black Rubber 17.00 pair
Part # Weight Capacity MSRP
A67 100 lb. 119.00(each)
eZ-Velcro strAp
Ì Strap a ladder with the EZ velcro straps.
Ì Holds up to a maximum of 75 lbs in combination with the ladder stopper or guide.
Ì Loops into cross bar.
Note: Currently does not fit 286 cross bars
Part # Height Bar Type Color MSRP
A69 10” All 75 lb. 18.00 (each)
4 pc. holder with strAps
Ì Holds Kayak, surfboards and canoes
Ì Adjustable rubber padding can conform to side or bottom of equipment
Part # Size Bar Type MSRP
A24 1”A285 A286
10.00 (pair)
A59 1.25”A285 A286
14.00 (pair)
A94 1”A270 A287 A613
10.00 (pair)
eyehook
Ì Eyehooks includes sliders to fasten into channel.
Ì Tighten eyehook to secure into place.
Part # Height Bar Type MSRP
A25 1.5” A285, A286
20.00 (pair)
A26 1.5” A270, A287, A613
20.00(pair)
AdjustAble eyehook Ì Eyehooks includes sliders to secure
into channel.
Ì Tighten knob to secure into place.
Part # Length Install Weight Capacity MSRP
A62 10’ Onto Eyehook 150 lbs 35.00 (each)
rAtchet tie-down
Ì The Vantech Ratchet tie-down attaches to eyehooks on the mounting uprights with 1/2” bolts.
Ì Sold as individuals
Part #Strap
LengthBar Type Weight Capacity MSRP
A61 7’ Channels 150 lbs 29.00 (each)
rAtchet tie-down
Ì Attach the Vantech Ratchet tie-down to the channels of the crossbar.
Ì Sold as individuals
Ì Adjustable along channels
Part # Bar Type MSRP
A47 Locking Key knob with key (sold in pairs) 39.00 (pair)
lockinG key knob
Ì Prevent theft of racks or equipment
Ì Fits all 3/8” threading on upright mounts
Vantech 6” conduit carrier. Ì Spring assist rear door for a water tight seal.
Ì Padlock tab for rear hatch door.
Ì Direct bolt-on system.
Ì Secures into channels of aluminum crossbars with sliders.
Ì Includes: Front cap, rear door, 2 “U” brackets and hardware.
Ì 6” PVC pipe not included.
Part # Description Bar Type MSRP
A34 6” Conduit Carrier (bolt on) All 89.00
Plastic Bar Guard
Ì 3/4" & 2" Plastic Bar Guards
Ì Adhesive on one side
Ì Extend life of crossbars.
Ì Prevents scratches on Cross Bars
Ì Can be cut to specific sizes
Ì Any excess can be cut to length
Ì Can be used on other surfaces
Part # Description Length MSRP
BG042 3/4” wide bar guards with self adhesive tape 42” 6.00
BG056 3/4” wide bar guards with self adhesive tape 56” 7.00
BG063 3/4” wide bar guards with self adhesive tape 63” 8.00
BG072 3/4” wide bar guards with self adhesive tape 72” 10.00
BG084 3/4” wide bar guards with self adhesive tape 84” 11.00
BG096 3/4” wide bar guards with self adhesive tape 96” 12.00
BG251 2” wide bar guards with self adhesive tape 51” 9.00
BG259 2” wide bar guards with self adhesive tape 59” 10.00
BG265 2” wide bar guards with self adhesive tape 65” 11.00
BG272 2” wide bar guards with self adhesive tape 72” 12.00
Part # Description Length MSRP
BG5483/4” wide non-slip rubber bar guards
(press in channels)48" 14.00
BG5653/4” wide non-slip rubber bar guards
(press in channels)65" 19.00
BG5723/4” wide non-slip rubber bar guards
(press in channels)72" 22.00
BG5843/4” wide non-slip rubber bar guards
(press in channels)84" 36.00
BG5963/4” wide non-slip rubber bar guards
(press in channels)96" 40.00
Part # Description Length MSRP
BG7481” wide rubber Cushion bar guards
(press in channels)48" 28.00
BG7651” wide rubber Cushion bar guards
(press in channels)65" 28.00
BG7721” wide rubber Cushion bar guards
(press in channels)72" 44.00
BG7841” wide rubber Cushion bar guards
(press in channels)84" 49.00
BG7961” wide rubber Cushion bar guards
(press in channels)96" 56.00
Surfaces without Channel
Surfaces with Channel
Surfaces with Channel
ruBBer Bar Guard
Ì Rubber Bar Guards
Ì Fits into channels of extruded aluminum bars
Ì Easy press-on design
Ì Can be cut to specific sizes
Ì Any excess can be cut to length
Ì minimize rattling sound
Ì Prevents scratches on Cross Bars
ruBBer Bar Guard cushion
Ì Rubber Bar Guards (Cushioned)
Ì Fits into channels of extruded aluminum cross bars.
Ì Function and install similar to normal rubber bar guard
Ì Additional air pocked for extra cushion
Ì Great for kayaks, boards, and other materials or equipment.
Part # Size Color MSRP
A108 3.75" Black 5.00
360°adjustaBle conVex Mirror (Adhesive bAck)
Ì Sticks onto side view mirror.
Ì Adhesive backing
Ì Convex Mirror to show more
top related