installing optical cables for main-remote solutions (2010)
Post on 12-Jul-2016
55 Views
Preview:
DESCRIPTION
TRANSCRIPT
Installing Optical Cables for Main-RemoteSolutions
INSTALLATION INSTRUCTIONS
15/1531-LZA 701 0003 Uen H
Copyright
© Ericsson AB 2007 - 2010. All rights reserved. No part of this document maybe reproduced in any form without the written permission of the copyright owner.
Disclaimer
The contents of this document are subject to revision without notice due tocontinued progress in methodology, design and manufacturing. Ericsson shallhave no liability for any error or damage of any kind resulting from the useof this document.
Trademark List
All trademarks mentioned herein are the propertyof their respective owners. These are shown in thedocument Trademark Information.
15/1531-LZA 701 0003 Uen H | 2010-11-08
Contents
Contents
1 Introduction 1
1.1 Target Group 1
1.2 Prerequisites 1
1.3 Documentation 1
2 Optical Cables 1
2.1 Handling Optical Cables 2
3 Installation Material 5
3.1 Installation Kits 5
3.2 Tools 5
4 Installing Optical Cables 6
4.1 Hoisting Optical Cables 6
4.2 Installing with Plastic Covered Steel Tie Straps 7
4.3 Installing with Cable Cleats 8
4.4 Installing Tubes 8
4.5 Installing Indoor Cable Chutes 10
4.6 Installing and Using Cable Winders 11
5 Checking the Installation 13
5.1 Common Causes of Faults 14
Glossary 15
Reference List 17
15/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables for Main-Remote Solutions
15/1531-LZA 701 0003 Uen H | 2010-11-08
Optical Cables
1 Introduction
This document describes general principles for how to install an optical cablebetween the main unit and the remote radio unit in a Main-Remote system.
1.1 Target Group
This document is for all personnel working directly or indirectly with the logistics,engineering, or installation.
1.2 Prerequisites
Technicians working with Ericsson products or systems must have thenecessary training and skills to perform their work correctly.
Safety Regulations
Before starting work on the site, the following documents must be read andunderstood:
• Personal Health and Safety Information,124 46–2885
• System Safety Information, 124 46–2886
1.3 Documentation
See Reference List on page 17 for needed documents.
2 Optical Cables
This section introduces optical cables and describes handling of optical fibercables.
Optical cables must be handled with care. Optical cables consist of thin glassfibers protected by plastic coating.
Connectors for different optical cables are listed in Table 1 and Table 2.
115/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables for Main-Remote Solutions
The LC, SC and ODC connectors are shown in Figure 1.
P018900C
LC ODC/RDCSC
Figure 1 LC, SC and ODC Connectors without Protective Covers
Note: Never touch the end face of the optical connectors. Only removeprotective covers immediately before connecting to the Main Unit (MU)or the Remote Radio Unit (RRU).
2.1 Handling Optical Cables
When handling optical cables, consider the following:
• Optical cables are sensitive to mechanical stress, sharp bends, kinks, dust,and dirt. They are not, however, sensitive to electrical interference.
• Never over-bend the cable. See Table 1 and Table 2 for minimum bendingradius.
• Make sure not to apply excessive force to the cable, See Table 1 and Table2 for maximum tensile force values.
• Be careful with the connectors when connecting optical cables to MUsand RRUs.
P018863A
OIL Cable
Minimumbendingradius
Minimumbendingradius
Acceptable Not acceptable(too sharp bend)
Figure 2 Minimum Bending Radius
2 15/1531-LZA 701 0003 Uen H | 2010-11-08
Optical Cables
2.1.1 Optical Cables Not Requiring Mechanical Protection for Installation
The optical cables in Table 1 do not require to be installed with mechanicalprotection, installation with plastic covered steel tie straps or cable cleatsis sufficient.
The L at the end of the product numbers defines the lengths of the opticalcables.
Note: The maximum allowed strapping distance applies if the optical cablesare installed outdoors with wind force conditions up to 55 m/s.
Table 1 Optical Cables Not Requiring Mechanical Protection for Installation
ProductNumber
Application,Main-RemoteSystem
Connectors(MU/RRU)
MinimumBendingRadius onMain Cable
MinimumBendingRadius onSplit Cable
MaximumTensileForce
MaximumLengthof FreeHangingCable
MaximumStrappingDistance
RPM 2531633/L
RBS 6601/RRUS 11
LC/LC(1) 40 mm 10 mm 300 N 50 m 0.5 m
RPM 2532788/L
RRU22/ RRUW LC/LC 40 mm 10 mm 300 N 50 m 0.5 m
RPM 2532895/L
RRUW/ RRUWRRUS/ RRUSRRUW/ RRUS
LC/LC 40 mm 10 mm 300 N 50 m 0.5 m
RPM 2533577/L R1B orlater
RBS 3018/RRUWRBS 3106(2)/RRUWRBS 3206(2)/RRUWRBS 3418/RRUWRBS 3518/RRUWRBS 6601/RRUWRBS 6601/RRUS 01
LC/LC 40 mm 10 mm 300 N 50 m 0.5 m
RPM 2533878/L R1B orlater
RBS 3412/RRUW
LC/LC 40 mm 10 mm 300 N 50 m 0.5 m
RPM 2534388/1000 R1Bor later
(3)ODC/LC 40 mm 10 mm 300 N 1 m 0.5 m
(1) With FULLAXS on RRU LC connector.(2) Macro RBS with OBIF(3) Adapter Cable, for replacing an RRU22 with an RRUW.
2.1.2 Optical Cables Requiring Mechanical Protection for Installation
The optical cables in Table 2 all require to be installed with mechanicalprotection.
The L at the end of the product numbers defines the lengths of the opticalcables.
315/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables for Main-Remote Solutions
Table 2 Optical Cables Requiring Mechanical Protection for Installation
Product Number Application,Main-RemoteSystem
Connectors(MU/RRU)
MinimumBendingRadius onMain Cable
MinimumBendingRadius onSplit Cable
MaximumTensileForce
MaximumLength ofFree HangingCable
RPM 119 0599/L RBS 8418/RRU46RBS 8418/RRU46iRBS 8418/RRU86RBS 8418/RRU86ARBS 8418/RRU112
LC/LC 40 mm n/a 300 N 30 m
RPM 119 0600/L RRU46/ RRU46RRU46i/ RRU46iRRU86/ RRU86RRU86A/RRU86ARRU112/RRU112
LC/LC 140 mm n/a 300 N 30 m
RPM 253 1306/L(1) RBS 3402/RRU11RBS 3412/RRU11
LC/LC 100 mm n/a 100 N 30 m
RPM 253 3577/LR1A
RBS 3018/RRUWRBS 3418/RRUWRBS 3518/RRUW
LC/LC 40 mm 15 mm 300 N 50 m
RPM 253 3878/LR1A
RBS 3412/RRUW
LC/LC 40 mm 15 mm 300 N 50 m
RPM 2534388/1000 R1A
(2)ODC/LC 40 mm 15 mm 300 N 1 m
TSR 899 071/L RBS 3402/RRU11RBS 3412/RRU11
LC/LC 100 mm n/a 300 N 50 m
TSR 899 088/L RBS 2111/RRU-N
SC/SC 50 mm n/a 300 N 50 m
TSR 899 099/L RBS 3412/RRU22
LC/ODC 100 mm n/a 300 N 50 m
TSR 899 113/L RBS 3018/RRU22RBS 3418/RRU22RBS 3518/RRU22RBS 6601/ RRUL
LC/ODC 100 mm n/a 300 N 50 m
TSR 899 115/L RBS 3018/RRU11RBS 3418/RRU11RBS 3518/RRU11
LC/LC 100 mm n/a 300 N 50 m
(1) For indoor use only.(2) Adapter Cable, for replacing an RRU22 with an RRUW.
4 15/1531-LZA 701 0003 Uen H | 2010-11-08
Installation Material
3 Installation Material
This section describes the installation kits and tools recommended for theinstallation.
3.1 Installation Kits
The installation kits are available in outdoor and indoor variants. Therecommended kits are listed below. See Reference [3] and Reference [4] forfurther installation materials.
Table 3 Installation Kits
Product Number Description
SET 145 095/457 Plastic Covered Steel Tie Straps Kit.
NTM 201 3931/1, NTM 2013931/2 or NTM 201 3931/3
Main Remote Cable Cleats Kits.
NTM 201 3811/1 Cable tube kit, 25 m flexible tubes, includingdraw wire and fastening material for tower,wall, and ladder.
NTM 201 3727/1 Cable tube kit, 8.5 m split tubes, includingfastening material for tower, wall, andladder.
NTM 201 3730/1 Indoor cable chute kit, 2×2 m includingfastening material for wall and ladder.
NTM 201 3728/1 Support kit for three optical cables and threepower cables in tower.
NTM 201 3729/1 Cable winder box for 30 m optical cableincluding fastening material for wall andtower.
NTM 201 3767/1 Marking set for WCDMA main-remote site.
NTM 201 3767/2 Marking set for GSM main-remote site.
3.2 Tools
The table below shows the tools required to install an optical cable. SeeReference [5] for further information on required tools.
515/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables for Main-Remote Solutions
Table 4 Tools
Product Number Description
LTT 601 135/1 or LTT 601 156/1 Personal tool set.
LSD 901 52/1 Cable tie tensioning tool.
LPB 112 102/1 Fiber check tool to check opticalcables.
LPK 102 111/1 OTDR, Optical Site Master with powermeter for measurement of opticalcables and optical transmission,testing distance up to 2.5 km.
LTT 601 154/1 Ferrule end-face cleaner for cleaningoptical cable ends on LC connectors.
4 Installing Optical Cables
This section describes the installation procedure of optical cables. See forfurther information on installation material.
4.1 Hoisting Optical Cables
To hoist an optical cable to an RRU, do the following:
1. Attach a sleeve to the optical cable to relieve the cable from any load.
Note: Position the sleeve so that the cable will easily reach the RRUconnector.
P018905A
6 15/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables
2. Attach a rope according to figureand pull the cable.
P018867A
3. Anchor the cable by a steel wire andcarabiner.
P018868A
Note: Each carabiner can be used to hold three optical cable sleeves andthree power cable sleeves, all cables going through the same tube.
4.2 Installing with Plastic Covered Steel Tie Straps
Plastic covered tie straps are sufficient for installing the optical cables in Table1, where mechanical protection is not required.
Apply the tie straps with a strapping distance according to Table 1.
715/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables for Main-Remote Solutions
4.3 Installing with Cable Cleats
Figure 3 shows cable cleats sufficient for installing the optical cables in Table 1,where mechanical protection is not required.
Figure 3 Cable Cleat
Apply the cable cleats with a distance according to Table 1.
4.4 Installing Tubes
This section describes how to install tubes for optical cables that requiremechanical protection.
Tubes are used to protect the optical cable from mechanical stress.
4.4.1 Installing Flexible Tubes
Flexible tubes can be installed on a rooftop, wall, or a tower.
To route the cables in different directions, use T-joints. See Figure 4. Thecables are easily pulled through the tube using a draw wire.
• When installing tubes on a rooftop, use included clamps either directly onthe roof or fixed to free-standing concrete slabs to avoid damage to theroof. See Figure 4.
• When installing tubes on an indoor or outdoor wall, use included clamps.
• When installing tubes on a tower, use included steel cable tie straps every0.8 m.
8 15/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables
P020154A
Figure 4 Flexible Tube Installation
4.4.2 Installing Split Tubes
Split tubes are preferred for installations on existing main-remote sites.
Split tubes can be installed on a tower or a wall.
To install tubes, do the following:
1. When installing tubes on a tower, use included steel cable tie straps.
2. When installing tubes on an indoor or outdoor wall, use included clamps.
3. Close the tubes, cover the joints with plastic sleeves and seal with tape.See Figure 5.
915/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables for Main-Remote Solutions
Note: For optimal stability, fasten three cable tie straps or clamps per tube,one on each end of the tube, next to the joints, and one in the middle.
P018861A
Figure 5 Split Tube Installation
4.5 Installing Indoor Cable Chutes
This section describes how to install indoor cable chutes for optical cablesthat require mechanical protection.
Indoor cable chutes are used to protect the optical cable from mechanicalstress and can be installed on a ladder or a wall.
To install indoor cable chutes, do the following:
1. Screw the cable chutes to a ladder or a wall.
10 15/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables
2. Lay the optical cable in the cable chutes and put on the cover.
P018869A
Figure 6 Indoor Cable Chute Installation
4.6 Installing and Using Cable Winders
Optical cables must never be cut. Instead, wind all excess cable on a cablewinder. Using a cable winder insures that the requirements on minimum cablebending radius are fulfilled.
The cable winder should be installed close to the main unit. It can be installedon a tower, on a wall or in a cabinet.
To install and use a cable winder, do the following:
1. Using a sharp tool, push out the marked cable entrance and exit holes onthe vertical side of the cable winder.
Note: It is recommended to polish the cable entrance and exit holes toavoid damaging of the optical cable.
2. When installing the cable winder on a tower, screw the brackets to thecable winder and attach them to the tower using steel cable tie straps,see Figure 7.
3. When installing the cable winder on a wall, drill holes through the cablewinder and screw it to the wall.
4. When installing the cable winder in a cabinet, insert the cable winder in a19-inch rack and attach with screws.
1115/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables for Main-Remote Solutions
P018859A
Figure 7 Winding the Optical Cable
5. Wind the excess optical cable on the cable winder according to Figure 7.
6. Attach the cover to the cable winder.
12 15/1531-LZA 701 0003 Uen H | 2010-11-08
Checking the Installation
5 Checking the Installation
Check the optical cable installation to insure that the cables have been handledproperly during the installation.
The optical cables are checked by using the fiber check tool to shine laser lightthrough the cable, see A in Figure 8.
Note: Never touch the end face of the optical connectors. Only removeprotective covers immediately before connecting to the MU or the RRU.
Start
Menu
Set
F1
F2
F3
F4
B
A
C
Figure 8 A: Checking the Optical Cable, B: Using the Ferrule End-FaceCleaner, C: the OTDR Sitemaster
Cable LC connectors can be cleaned using the ferrule end-face cleaner, see Bin Figure 8.
After cleaning, check again that the laser light goes through the cable.
If fault or high attenuation still is suspected then use the OTDR, Optical SiteMaster, see C in Figure 8.
If the problem remains, then it is probably due to improper handling of theoptical cable (see Section 5.1 on page 14) and the cable must be replaced.Contact site supervisor before taking action.
1315/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables for Main-Remote Solutions
5.1 Common Causes of Faults
Common causes of faults include kinks in cables and cable tie straps that aretoo tight, as shown in Figure 9.
P018890A
Figure 9 Wrong Handling of Optical Cables
14 15/1531-LZA 701 0003 Uen H | 2010-11-08
Glossary
Glossary
MUMain Unit
N/A, n/aNot applicable
OTDROptical Time Domain Reflectometer
RRURemote Radio Unit
1515/1531-LZA 701 0003 Uen H | 2010-11-08
Installing Optical Cables for Main-Remote Solutions
16 15/1531-LZA 701 0003 Uen H | 2010-11-08
Reference List
Reference List
The following documents are related to this procedure:
Safety
[1] Personal Health and Safety Information, 124 46-2885
[2] System Safety Information, 124 46-2886
Site
[3] Main-Remote Installation Products Overview, 16/1551-LZA 701 0003
[4] Site Installation Material Overview, EN/LZT 751 0049
[5] Site Implementation Team Products Overview, EN/LZT 751 0065
1715/1531-LZA 701 0003 Uen H | 2010-11-08
top related