installation guide · insulate your garage door with foilboard® rigid panel insulation installing...
Post on 12-Aug-2020
1 Views
Preview:
TRANSCRIPT
To achieve maximum thermal value and to ensure the quickest and simplest installation of Foilboard® GREEN rigid insulation panel to stud wall systems, Foilboard® Australia recommends the following methods.
Foilboard® GREEN rigid insulation panel should be installed to the external face of the studwork, with the anti-glare side facing out. Measure the area you require.
Mark the measurements out on the Foilboard®
GREEN rigid insulation panel, using the gridlines (registered design) as a guide. Using a straight edge and a sharp blade / knife, cut the rigid panel to size.
STEP 1
STEP 2
It’s the smarter way to insulatewww.foilboard.com.au
Use Foilboard® Standard Fasteners (timber frame) for Foilboard® GREEN 10 & GREEN 15Use Ultra Fasteners for Foilboard® GREEN 20 & GREEN 25
Use Foilboard® Steel Standard Fasteners (steel frame) for Foilboard® GREEN 10 & GREEN 15 Use Steel Ultra Fasteners for Foilboard® GREEN 20 & GREEN 25
Foilboard® green joining tape
OR
AND
Resi 1 Brick Veneer (timber frame / steel frame)
Installation Guide
You can also check out our installation videos online at -foilboard.com.au
Simple step by step guide to installing Foilboard® GREEN rigid insulation
BRICK VENEER
Required to install
To achieve maximum thermal value and to ensure the quickest and simplest installation of Foilboard® GREEN rigid insulation panel to stud wall systems, Foilboard® Australia recommends the following methods.
Foilboard® GREEN rigid insulation panel should be installed to the external face of the studwork, with the anti-glare side facing out. Measure the area you require.
Mark the measurements out on the Foilboard®
GREEN rigid insulation panel, using the gridlines (registered design) as a guide. Using a straight edge and a sharp blade / knife, cut the rigid panel to size.
STEP 1
STEP 2
It’s the smarter way to insulatewww.foilboard.com.au
Use Foilboard® Standard Fasteners (timber frame) for Foilboard® GREEN 10 & GREEN 15Use Ultra Fasteners for Foilboard® GREEN 20 & GREEN 25
Use Foilboard® Steel Standard Fasteners (steel frame) for Foilboard® GREEN 10 & GREEN 15 Use Steel Ultra Fasteners for Foilboard® GREEN 20 & GREEN 25
Foilboard® green joining tape
OR
AND
Resi 1 Brick Veneer (timber frame / steel frame)
Installation Guide
You can also check out our installation videos online at -foilboard.com.au
Simple step by step guide to installing Foilboard® GREEN rigid insulation
BRICK VENEERRequired to install
To achieve maximum thermal value and to ensure the quickest and simplest installation of Foilboard® GREEN rigid insulation panel to stud wall systems, Foilboard® Australia recommends the following methods.
Foilboard® GREEN rigid insulation panel should be installed to the external face of the studwork, with the anti-glare side facing out. Measure the area you require.
Mark the measurements out on the Foilboard®
GREEN rigid insulation panel, using the gridlines (registered design) as a guide. Using a straight edge and a sharp blade / knife, cut the rigid panel to size.
STEP 1
STEP 2
It’s the smarter way to insulatewww.foilboard.com.au
Use Foilboard® Standard Fasteners (timber frame) for Foilboard® GREEN 10 & GREEN 15Use Ultra Fasteners for Foilboard® GREEN 20 & GREEN 25
Use Foilboard® Steel Standard Fasteners (steel frame) for Foilboard® GREEN 10 & GREEN 15 Use Steel Ultra Fasteners for Foilboard® GREEN 20 & GREEN 25
Foilboard® green joining tape
OR
AND
Resi 1 Brick Veneer (timber frame / steel frame)
Installation Guide
You can also check out our installation videos online at -foilboard.com.au
Simple step by step guide to installing Foilboard® GREEN rigid insulation
BRICK VENEER
Required to install
It’s the smarter way to insulatewww.foilboard.com.au
GA
RAGE D
OO
RInstallation Guide
It’s the smarter way to insulatewww.foilboard.com.au
Garage Door Insulation
Required to install • Australian made• Lightweight• Easy to install• High thermal efficiency• Rigid insulation• Size of sheet 2400x1200 • Coverage 2.88m2
Insulate your garage door with Foilboard® Rigid Panel Insulation
Installing FOILBOARD® Behind Garage Door: 1. Measure the width of each
horizontal panel and cut the FOILBOARD® Green 15 to size using a straight edge and Snap Blade Knife. The FOILBOARD® should be cut across the width for ease of installation.
2. Using FOILBOARD Silver Insulation Tape seal all exposed edges of the FOILBOARD®.
3. Using FOILBOARD Spacer Blocks stick Spacer Blocks to one side of the FOILBOARD®.
4. Using a suitable High Temperature Resistant adhesive / silicone, adhere the FOILBOARD® to the inside of the Metal Tilt Panel. (Place high temp adhesive / silicone to the Spacer Blocks only)
5. Repeat the above 4 steps for all Panels.
Tape all joins with Foilboard® Silver Insulation tape.
Using FOILBOARD® Spacer Blocks with the FOILBOARD® will provide an Air Cavity that greatly increases the insulation performance.
FOILBOARD® comes in a range of thicknesses to suit any project. Visit the website for details.
Ph: 1800 354 717
1. Foilboard Spacer Blocks FB 071
2. Foilboard Silver Tape FB 062
3. Knife
top related