installation and commissioning of idirect infiniti modems

Installation and Commissioning of iDirect

iNFINITI Modems

Agenda

Satellite Basics Lunch

Unpack a CrateInstallation PresentationDemo’s

Image / Option loadDemo of Pointing Program

Hands-on Line upBreak for Supper / Sleep

Troubleshooting

Welcome to…

Basic Network Description

iNFINITY Seriessatellite router

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

Required Equipment

1. A console Cisco cable

2. A cross-over LAN cable

3. Digital (or Analog) Voltmeter plus adaptor from voltmeter to F” type connector

4. A hand-held GPS unit or a map that shows your current geographic location coordinates

5. A laptop (or PC) with Windows XP or Windows 2000 Service Pack 3 loaded. Disable the firewall to ensure complete functionality.

6. The correct options file provided to you by your Service Provider.

7. The correct remote application and firmware images (or correct “package”) provided to you by your Service Provider.

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

What is iSite? Why iSite?

Front-End Interface for All iDirect ProductsGUI Support for iDirect iNFINITY satellite routers - TDMA

GUI Support for iDirect iNFINITY satellite routers - iSCPC Network

GUI Support for Series 1000, Network Accelerator

Provides Local or Remote GUI Access forImage & Option File Download, all Products

Monitoring of Remote Site Network Performance, all Products

Full Configuration Build, iSCPC Modem parameters, QoS, IP, etc.

Full Configuration Build, Series 1000 Network Accelerator

Pointing functions

Supplemental NMS Client for Remote Site Implementation

What does iSite Look Like?

Other iSite Features

Manage Multiple Units from a Single InterfaceControl TDMA remotes, iSCPC units, VPN simultaneously

Auto-discovery of LAN unitsUnits on same LAN are automatically discoveredMonitoring of board available without logging in

All Features Available across Remote RoutersEventsIP statisticsPointing functions

Audio Feedback during PointingPoint without looking at display or DVM if desired

Device-Specific Configuration and DisplayLevel of configuration determined by device typeFull configuration for iSCPC/NA, restricted for TDMA remote (GEO Location update for TDMA ‘Mobile’ remotes only)

Install iSite and Remote Modem Images on your Laptop

Currently, the Images for iDirect iNFINITI satellite router and iSite software are bundled together

The NMS iSite program and support files

The iNFINITI Remote-Modem application and image files

Install iSite1. Uncompress the files by using a utility that understands the .zip format.

2. If desired, create a shortcut on the desktop or Windows taskbar to iSite.exe (located in the iSite folder).

3. Run the iSite program wizard to install the software on your laptop (or PC)

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

In order to find out the unit IP address use the following steps:

Open the putty softwareChoose the serial option on the rightPress open A putty session will open the console port Logon to infiniti with default login “root”, password “iDirect”.Type ifconfigiDirect will return 3 cards the first one is the LAN IP address and subnet Mask of the unit.Exit putty and open iSite software.

Setting Up Your PC:Network Interface

Setting Up Your PC:Network Interface

Verify LAN Connectivity

Open DOS Command Window

Verify NIC Address with “ipconfig”

Ping Remote from DOS Window to Verify Connectivity

Telnet into the unit

Check the version of the unit with “version” command

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

iSite Main Window

1

Login to iNFINITI

Menu Selection: Download Package (1/2)

Menu Selection: Download Package (2/2)

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images packages to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

Download Option (1/2)

Download Option (2/2)

Remote & HLC Software

Example of an option file

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

Set up your Antenna

Select a Site for the Antenna 1. Select a level surface that is approximately 10 feet by 10 feet.

2. Verify that nothing is blocking the line of sight to the satellite in azimuth and elevation

3. Verify the IFL cable can reach the Satellite Router from the antenna location (RG-6 IFL cable may be used up to a distance of 250 feet. If your run is longer, RG-11 must be used, up to a distance of 500 feet.)

4. Verify that the IFL cable does not cross roads or heavy foot-traffic areas.

Assemble the Antenna1. The antenna base is on a stable surface that will not shift during windstorms.

2. Ballast is installed on the antenna base.

3. The mast pipe is plumb.

Set up your Antenna (2/2)

Align the Antenna toward the Spacecraft

1. Set the antenna’s polarization to the approximate value provided by iSite’s Look Angle Calculator.

2. Set elevation to the value provided by iSite’s Look Angle Calculator.

3. To prepare the antenna for pointing, move the antenna off the desired azimuth, by swinging the antenna 20° away in azimuth. This will enable you to get a clear sky reading and compare signal strengths during the antenna pointing procedure.

The offset for a 1.8 meter antenna is 22.6°

Elevation Satellite W3A: 34º

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

Antenna Pointing:Look Angle Calculator

W3A 7°E

48N 4E

17

32

Antenna Pointing:Pulse Width Modulation (PWM) Antenna Pointing

Next, you must fine-tune the antenna pointing. You will attempt to lock onto the downstream carrier for your network, by sweeping the antenna in azimuth, looking for a value in the range of 12 to 24 volts DC. Readings in this range indicate that you have successfully locked into the correct satellite.

Antenna Pointing:Pulse Width Modulation (PWM) Antenna Pointing

Note: Remember to ALWAYS Power down iNFINITIWhen Connecting and/or Disconnecting IFL Cables

Antenna Pointing:Pulse Width Modulation (PWM) Antenna Pointing

Antenna Pointing:Pulse Width Modulation (PWM) Antenna Pointing

When you have found the desired signal: Tighten down the 4 bolts on the Yoke Cap that secure the Yoke Cap to the Mast Pipe.

Ensure that the Top Plate locking bolts are snug to allow azimuth movement.

Adjust the elevation until maximum dc voltage is obtained.

The rest of the azimuth adjustments will be made with the azimuth adjustment screws. Fine tune azimuth until maximum dc voltage is obtained

Make sure azimuth and elevation are locked down

Adjust polarization until maximum dc voltage is obtained

Write down the final antenna pointing voltage reading and give the reading to the operator at the Network Help Desk

In iSite, click Stop to exit the modem’s antenna pointing mode

Power down the Satellite Router.

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser 9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser 9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

Cross Polarization

Note: Rx cable must be disconnected; Tx cable must be connected; Remember to ALWAYS Power down iNFINITI when Connecting/Disconnecting IFL Cables

Cross Polarization

The satellite provider will then ask to have the azimuth, polarization, and/or elevation adjusted. The polarization is usually adjusted first. If the correct isolation cannot be achieved, then the operator may ask to adjust the azimuth and/or elevation.

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser 9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

Align Antenna:1 dB Compression Test

Establish the 1 dB Compression Point

The 1 dB Compression Point test is performed with the same CW setup used during the previous cross polarization test. This test establishes the point at which the Satellite Router’s transmit power saturates the BUC.

Record the TX power value. This will be used as the maximum power for this remote in the NMS.

Align Antenna:1 dB Compression Test

Remote Installation Summary

1. Required equipment2. Install iSite software and remote modem images on your laptop3. Establish a console & network connection to the satellite router4. Download the application and images package to the satellite router5. Download the options file to the satellite router6. Set up your antenna7. Point the antenna using a voltmeter on the transmit IFL cable8. Point the antenna using an analyser 9. Fine-tune the antenna pointing and cross polarization10.Establish the 1 dB compression point11.Bring the satellite router into the network

Bring the satellite router into the network

Power off iNFINITI

Connect both Tx and Rx IFL cable

Boot iNFINITIThe Satellite Router should perform its power-up self-test and acquire into the network.

Observe the LEDs on the front of the Satellite Router while the network powers on and goes through the acquisition process. You will see various combinations of front-panel lights indicating the current status of the Satellite Router.

If your Satellite Router does not acquire into the network, contact the Network Help Desk for assistance.

QUESTIONS& ANSWERS