industrial computer industrial motherboard wmix-n26006 manual … · 2015. 4. 3. · chapter 2 bios...

WMX-N26006 Intel Atom N2600 User Manual Rev. 01, Apr. 2013

Contents

Chapter 1 Product Information .................................................................................................. 4

1.1 Block Diagram ............................................................................................................. 4

1.2 Features ........................................................................................................................ 5

1.3 PCB Layout .................................................................................................................. 7

1.4 Jumper Setting ............................................................................................................. 9

1.5 Connector Function List ............................................................................................ 13

1.6 Internal Connector Pin Define ................................................................................... 14

Chapter 2 BIOS Setup .............................................................................................................. 20

2.1 Main Menu ................................................................................................................. 20

2.2 Advanced Menu ......................................................................................................... 21

2.3 PCI Subsystem Setting ……………………………………………………………. 23

2.4 Advanced BIOS Feature Setup .................................................................................. 24

2.5 CPU Configuration .................................................................................................... 25

2.6 SATA Configuration ................................................................................................... 26

2.7 USB Configuration .................................................................................................... 27

2.8 Super IO Configuration .............................................................................................. 29

2.9 Serial Port 0 Configuration ........................................................................................ 30

2.10 Serial Port 1 Configuration ...................................................................................... 31

2.11 Parallel Port Configuration ...................................................................................... 32

2.12 Pc Health Status ....................................................................................................... 33

2.13 Serial Super IO Configuration ................................................................................. 32

2.14 Serial Port Configuration ......................................................................................... 32

2.15 Chipset ..................................................................................................................... 39

2.16 Memory Information ................................................................................................ 40

2.17 Chipset Configuration .............................................................................................. 41

2.18 Intel IGD Configuration ........................................................................................... 42

2.19 PCI Express Root Ports Configuration .................................................................... 43

2.20 USB Mode ............................................................................................................... 44

2.21 PCI Express Ports Configuration ............................................................................. 46

2.22 Boot Configuration .................................................................................................. 48

2.23 Password Description............................................................................................... 50

2.24 Save Changes and Exit ............................................................................................. 51

Chapter 3 Drivers Installation .................................................................................................. 52

3.1 Intel Chipset Device Software ................................................................................... 52

3.2 Intel Graphic Media Accelerator Driver .................................................................... 55

3.3 LAN Driver ................................................................................................................ 58

3.4 Audio Driver .............................................................................................................. 60

Appendix-A Watchdog ............................................................................................................. 61

Appendix-B GPIO ................................................................................................................... 63

Chapter 1 Product Information This chapter introduces the product features, jumper and connector information. 1.1 Block Diagram

DM I 4 Lan e s

DDR3 800/1066MHz

LPC I/ F

CG82NM10NM10

Intel ATOMSO-DIMM X2

S M B u s

SM Bus

KB&MS COM2LPT

SPI SIO_W83627EHG

USB 2.0 x8

SATA1 CONNSATA2 CONN or

COM3 COM4

SIO_ F81216D

D2 Series / N2 Series

CODEC_ALC662 HD Aud io

LAN1_RTL8111EPCIe x1

PCIe x1

mini-PCIe SlotPCIe x1

USB 2 .0

ISL95837HRZ

LAN2_RTL8111E

CH7511LVDS 24bit eDP

HDMIDP

32.768KHZRT C

P 04,05,06.07

P 08,09

P 10,11,12

P 20 P 15 P 15

P 16P 16

P 29 9VRS4339BKLF/MLF56P 03

P 17,22,23,24

P 16P 16COM5 COM6

PCI CONN

ASM1442/QFN48P 26

LVDS 18bit P 4

1.2 Features

System

Processor/Chipset

Processor Intel® ATOM processors with integrated

graphics and memory controller

D2550/N2800/N2600

Chipset Intel® NM10 Express Chipset

BIOS AMI

Memory

Technology

Support for DDR3 1066/1333/1600 MHz

SO-DIMMs. (Non-ECC, unbuffered)

Note : DDR3 1333MHz and DDR3 1600

MHz SO-DIMMs operate at 1066MHz Only

Max. Capacity Support up to 4GB of system memory

Max. 4GB for D2550; 2GB for N2600.

Socket Two 204-pin DDR3 SO-DIMM

Display

Chipset

Intel® Graphics Media Accelerator 3600

Intel® GMA 3650 for D2550

Intel® GMA 3600 for N2600

Video RAM

1GB total RAM results in 128MB video

2GB total RAM results in 224MB video

VGA Resolution up to 1920x1200 at 60 Hz

refresh (WUXGA)

18 bit single channel (WMX-N26006)

24 bit single channel (WMX-D25506)

24 bit dual channel support thru CH7511

HDMI Resolution up to 1920 x 1200

Dual Display CRT + LVDS, CRT + HDMI

Ethernet

Interface Gigabit (10/100/1000 Mb/s)

Controller LAN1: Realtek 8111E

LAN2: Realtek 8111E

Audio Interface High Definition Audio

Controller Realtek ALC662 HD audio codec

Max. Data

Transfer Rates 3.0Gb/s

Port 1

Expansion Slot PCI 1

Mini-PCIe 1

M-SATA 1 (Option)

Note: Mini-PCIe Socket

Rear I/O

PS/2 1 (K/B & M/S)

2xRS-232

1xRS-232/RS-422/RS-485

All support 12V/5V/RI

USB2.0 6

Audio 1 (Line In, Line out, Mic In)

HDMI HDMI Connector

Power DC 2 x 2 Pin x1 (WMX-D25506DF)

ATX 2 x 10 Pin x1 (WMX-D25506AF)

Onboard

Pin-Header

LVDS18 LVDS18Bit for WMX-N26006

LVDS24Bit for WMX-D25506

LVDS24 1

FAN 1 x CPU Fan

1 x SYS Fan

USB 2.0 1

SATA 1

SATA Power 1

Parallel 1

COM 3 x RS232

Front Panel 1

SMBUS 1

DIO 4 in/4 out

Watchdog Timer Output System reset

Interval Programmable 1~255 sec./min.

Environment

Operating Temp. -20°C~ 70°C (-4°F~158°F)

Storage Temp. -20°C~ 80°C (-4°F~176°F)

Relative Humidity 0%~ 95% (non-condensing)

Dimension

(L x W) 170mm x 170mm (6.69"x6.69")

1.3 PCB Layout Top View

LVDS18

JLVDS2

BAT2JCMOS1 SATA1 SATA2_PWR1

COM4 COM5 COM6JFRONT1

CPUFAN1

USB1PCI1

JPWR_SEL1

AUDIO2

MINI-PCIE1

CPUFAN2

JCOM3JCOM1

COM1_COM1

USB1_KBMS1

JCOM2_SEL1

COM+VGA

USB2_LAN2 USB2_LAN1 HDMI1AUDIO1

SATA_PWR1

SATA_PWR2

JLVDS1

JLVDS_SEL1

LVDS24

INV2INV1 SO-DIMM1

SO-DIMM2

SO-DIMM2A1

Bottom View

MSATA1

1.4 Jumper Setting

JCMOS1: CMOS Clear Pin No. 1-2 2-3 Function Normal Operation (Default) Clear CMOS Contents

Jumper

Setting

JCOM1/JCOM2/JCOM3: (5V/12V/RI) Select Pin No. 1-2 3-4 5-6 Function +5V Modem Ring In

(Default)

Jumper Setting

JCOM2_SEL1: COM2 (RS-232/RS-422/RS-485) Select (1/3)

Pin No. 5-6, 11-13, 12-14, 19-21, 20-22 3-4, 9-11, 10-12, 17-19, 18-20 Function RS-232 (Default) RS-422

Jumper

Setting

JCOM2_SEL1: COM2 (RS-232/RS-422/RS-485) Select (2/3) Pin No. 1-2, 9-11, 10-12, 23-24 15-16 Function RS-485 RS-422 RX 100Ω Termination

Jumper

Setting

JCOM2_SEL1: COM2 (RS-232/RS-422/RS-485) Select (3/3)

Pin No. 7-8

Function RS-422 TX 100Ω/RS-485

Termination

Jumper

Setting

Note: Not Recommended for RS-422 TX 100Ω Termination.

JLVDS1/LVDS2: LCD Power (+3.3V/+5V) Select

Pin No. 1-2 2-3 Function LCD Power +3.3V (Default) LCD Power +5V

Jumper

Setting

JPWR_SEL1: AT/ATX Mode Select

Pin No. 1-2 2-3 Function AT Mode ATX Mode (Default)

Jumper

Setting

JLVDS_SEL1: LVDS Panel Type Select Jumper Setting LVDS Panel Type

800*600/18bit

Single Channel

1024*768/18bit

Single Channel

1024*768/24bit

Single Channel

1 3 5 7

2 4 6 8

1280*768/18bit

Single Channel

1 3 5 7

2 4 6 8

1280*800/18bit

Single Channel

1280*960/18bit

Single Channel

1280*1024/24bit

Dual Channel

1366*768/18bit

Single Channel

1366*768/24bit

Single Channel

1 3 5 7

2 4 6 8

1 3 5 7

2 4 6 8

1 3 5 7

2 4 6 8

1 3 5 7

2 4 6 8

1 3 5 7

2 4 6 8

1 3 5 7

2 4 6 8

1 3 5 7

2 4 6 8

1400*900/24bit

Dual Channel

1 3 5 7

2 4 6 8

1400*1050/24bit

Dual Channel

1 3 5 7

2 4 6 81600*900/24bit

Dual Channel

1 3 5 7

2 4 6 81680*1050/24bit

Dual Channel

1 3 5 7

2 4 6 81600*1200/24bit

Dual Channel

1 3 5 7

2 4 6 8

1920*1080/24bit

Dual Channel

1 3 5 7

2 4 6 8

1920*1200/24bit

Dual Channel

1 3 5 7

2 4 6 8

1.5 Connector Function List

Connector Function Note AUDIO1 Line-In/MIC-In/Line-Out Connectors

AUDIO2 Audio Amplifier Output Connector

MSATA1 MSATA Connector

COM1_COM1 COM1, COM3 Serial Port Connector

COM4, COM5, COM6 Serial port with Box-header

DIO1 Digital I/O Connector

INV1 LCD inverter connector for LVDS24

INV2 LCD inverter connector for LVDS18

LPT1 Parallel Port Connector

LVDS18 LVDS Connector

LVDS24 LVDS Connector

MCR1 MCR with Box-header

MINI-PCIE1 Mini PCI Express connector

PWR2 ATX 2x10 connector For ATX PUS

PWR1 ATX 2x2 connector For DC12V In

SATA1 SATA Connector

SATA_PWR1 SATA Power Connector

SO-DIMM1/2 DDR3 SO-DIMM connector x 2

CPUFAN1 System FAN 3 Pin connector

CPUFAN2 CPU FAN 4 Pin connector

USB2_LAN1 USBx2 and RI45-LAN Conenctor

USB2_LAN2 USBx2 and RI45-LAN Conenctor

JLVDS_SEL1 LVDS24 Panel Type Select

USB1_KBMS1 USBx2 and PS2 Keyboard/Mouse

USB1 USB 5 Pin Header

COM+VGA VGA and COM2 Serial Port Connector

VGA2 VGA Pin Header

HDMI1 HDMI Connector

1.6 Internal Connector Pin Define

AUDIO2: Audio Amplifier Output with Box-header (2.0mm) Pin No. Signal

1 Audio Amplifier Out Right

2 Ground

3 Ground

4 Audio Amplifier Out Left

COM4/COM5/COM6: Serial Port with Box-header (2.0 mm) Pin No. Signal Pin No. Signal

1 DCD 2 DSR

3 RXD 4 RTS

5 TXD 6 CTS

7 DTR 8 RI/+5V/+12V

9 Ground 10 NC

DIO1: Digital I/O with Pin-header (2.00mm) Pin No. Signal Pin No. Signal

1 DIO-Out0 bit0 2 DIO-In0 bit2

9 +12V 10 +5V

11 Ground 12 NC

INV1/INV2: Inverter with Box-header (2.54mm) Pin No. Signal

1 +12V

2 +12V

3 Ground

4 Inverter Brightness Adjust

5 Inverter Brightness Enable

CPUFAN2: 4Pin FAN connector Pin No. Signal

1 Ground

2 Fan Power (+12V)

3 Speed Sense

4 Control

CPUFAN1: CPU/System FAN 3 Pin connector Pin No. Signal

1 Ground

2 Fan Power (+12V)

3 Speed Sense

VGA2: VGA with Box-header (2.0mm) Pin No. Signal Pin No. Signal

1 VGA_RED 2 VGA_DDC_DATA

3 VGA_GREEN 4 VGA_DDC_CLK

5 VGA_BLUE 6 Ground

7 VGA_ HSYNC 8 Ground

9 VGA_ VSYNC 10 Ground

PWR2: ATX 2x10 Connector Pin No. Signal Pin No. Signal

1 3.3V 11 3.3V

2 3.3V 12 -12V

3 Ground 13 Ground

4 5V 14 PS_ON

5 Ground 15 Ground

6 5V 16 Ground

7 Ground 17 Ground

8 PW_OK 18 -5V

9 5VSB 19 5V

10 12V 20 5V

JFRONT1: Front Panel with Pin-header (2.54mm) Pin No. Signal Pin No. Signal

1 +5V Power LED 2 Ground

3 HDD_PWR 4 HDD_LED#

5 SUS_LED 6 SUS_LED

7 SYS_RST# 8 Ground

9 SW_PWR# 10 Ground

LVDS18: LVDS 18 bit Panel Signal with Box-header (1.0mm) Pin No. Signal Pin No. Signal

1 Ground 2 Ground

3 LVDS_TXP3 4 LVDS_TXN3

5 LVDS_CLKP 6 LVDS_CLKN

13 Ground 14 Ground

15 NC 16 NC

17 NC 18 NC

19 NC 20 NC

21 NC 22 NC

23 NC 24 NC

25 Ground 26 Ground

27 +VLVDS 28 +VLVDS

29 +VLVDS 30 +VLVDS

Note1: +VLVDS18 = +5V or +3.3V (Default)

LVDS24: LVDS 24 bit Panel Signal with Box-header (1.0mm) Pin No. Signal Pin No Signal

1 Ground 2 Ground

3 L_DC3P 4 L_DC3N

5 L_CLK1P 6 L_CLK1N

7 L_DC2P 8 L_DC2N

9 L_DC1P 10 L_DC1N

11 L_DC0P 12 L_DC0N

13 Ground 14 Ground

15 L_DC7P 16 L_DC7N

17 L_CLK2P 18 L_CLK2N

19 L_DC6P 20 L_DC6N

21 L_DC5P 22 L_DC5N

23 L_DC4P 24 L_DC4N

25 Ground 26 Ground

27 +VLVDS 28 +VLVDS

29 +VLVDS 30 +VLVDS

Note1: +VLVDS = +5V or +3.3V (Default)

LPT1: Parallel Port with Box-header (2.0mm) Pin No. Signal Pin No. Signal

1 Strobe# 14 Auto Form Feed#

2 Data 0 15 Error#

3 Data 1 16 Initialization#

4 Data 2 17 Printer Select IN#

5 Data 3 18 Ground

6 Data 4 19 Ground

7 Data 5 20 Ground

8 Data 6 21 Ground

9 Data 7 22 Ground

10 Acknowledge# 23 Ground

11 Busy 24 Ground

12 Paper Empty 25 Ground

13 Printer Select 26 Ground

MCR1: Internal Keyboard with Box-header (2.0mm) Pin No. Signal

2 KCLK_CON

3 KCLK_KBC

4 KDAT_CON

5 KDAT_KBC

6 Ground

Note: If not use MCR need short (Pin2 to Pin3) and (Pin4 to

Pin5) to enable PS2 Keyboard.

PWR1: ATX 2x2 +12V Input Pin No. Signal Pin No. Signal

1 Ground 2 Ground

3 +12V 4 +12V

P1P2P3P4

USB1_KBMS1: USBx2, PS2 Keyboard and PS2 Mouse connector (PS2 Y-Cable)

Pin No. Signal P1 PS2_Ground

P2 PS2 Keyboard Data

P3 PS2 Mouse Data

P4 PS2 Power (+5V)

P5 PS2 Keyboard Clock

P6 PS2 Mouse Clock

USB1: USB Port with Pin-header (2.54mm) Pin No. Signal

1 USB Power (+5V)

2 USB DATA7N

3 USB DATA7P

4 USB Ground

SATA_PWR1: SATA Power with Box-header (2.50mm) Pin No. Signal

2 Ground

3 Ground

4 +12V

IR: IrDA Port with Pin-header (2.54mm) Pin No. Signal

1 Power (+5V)

3 IRRX

4 Ground

5 IRTX

Chapter 2 BIOS Setup

This chapter introduces BIOS setup information.

Power on or reboot the system board, when screen appears message as “Press DEL

to enter SETUP.” Press <DEL> to run BIOS SETUP Utility.

Note: The BIOS configuration for reference only, it may subject to change without

prior notice.

Main Advanced Chipset Boot Security Save & Exit

Choose the system default language

Enter : Select+/- : Change Opt .F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save & ExitESC: Exit

: Select Screen: Select Item

BIOS InformationBIOS VendorCore VersionCompliancyProject VersionModel NameBIOS VersionBuild Date and Time

System Language

System DateSystem Time

Access Leve1

American Megatrends4.6.5.1UEFI 2.3; PI 1.21APJK 0.14 WMX-N26006R00012/17/2012 15:19:38

[English]

[Fri 01/18/2013][10:22:09]

Administrator

Date Set system date.

Time Set system time.

2.2 Advanced Menu This section allows you to configure CPU and other system devices for basic operation

through the following sub-menus.

Boot Option for relTek8111E NIC.

Advanced

Legacy OpROM SupportOnboard PXE OpROMWake On PCIe LanResume By PMEWake On RingResume By RTC AlarmLaunch Storage OpROM

PCIACPICPUIDE USBSuperH/WSecond

Subsystem SettingsSettingsConfigurationConfigurationConfigurationIO ConfigurationMonitorIO Configuration

[Disabled][Disabled][Disabled][Disabled][Disabled][Enabled]

Onboard PXE OpROM Choices: Disabled, Enabled.

Wake On PCIe Lan Choices: Disabled, Enabled.

Resume By PME Choices: Disabled, Enabled.

Wake On Ring

Choices: Disabled, Enabled.

Resume By RTC Alarm Choices: Disabled, Enabled.

Launch Storage OpROM Enabled: Use this setting to specify that legacy PCI option ROMs for PCI storage

devices are to be loaded and executed.

In case of multipleOption ROMs (Legacy and EFI Compatible) ,specifies what PCIOption ROM to launch.

Advanced

PCI Bus Driver Versio

PCI Option ROM HandlingPCI ROM Priority

PCI Common SettingsPCI Latency TimerVGA Palette Snoop

V 2.05.01

[EFI Compatible ROM]

[32 PCI Bus Clocks][Disabled]

PCI ROM Priority

In case of multiple optional ROMs (Legacy and EFI Compatible), specifies what PCI

option ROM to launch.

PCI Latency Timer Choices: 32 PCI, 64 PCI, 96 PCI, 128 PCI, 160 PCI, 192 PCI, 224 PCI, 248 PCI Bus

Clocks.

VGA Palette Snoop Enable or Disable VGA palette registers snooping.

Enables or DisablesBIOS ACPI AutoConfiguration.

Advanced

ACPI Settings

Enable ACPI Auto Conf

Enable HibernationACPI Sleep StateS3 Video Repost

[Disabled]

[Enabled][S3 (Suspend to RAM)][Disabled]

Enable Hibemation Choices: Disabled, Enabled. ACPI Sleep State Select the highest ACPI sleep state the system will enter, when SUSPEND button is

pressed.

S3 Video Repost Choices: Disabled, Enabled.

Enabled for Windows XPand Linux (OS optimizedfor Hyper‐Threading Technology) andDisabled for other OS(OS not optimized forHyper‐ThreadingTechnology).

Advanced

WATX‐Q670 BIOS RA01 20120104

CPU Configuration

Processor TypeEMT64Processor SpeedSystem Bus SpeedRato io StatusActual RatioSystem BUS SpeedProcessor SteppingMicrocode RevisionL1 Cache RAML2 Cache RAMProcessor CoreHyper-Threading

Hyper-ThreadingExecute Disable BitLimit CPUID Maximum

Intel(R) Atom(TM) CPUNot Supported1600MHZ400 MHZ1616400 MHZ306612652x56 k2x512 kDualSupported

[Enabled][Enabled][Disabled]

Hyper-Threading Choices: Disabled, Enabled. Execute Disabled Bit Choices: Disabled, Enabled. Limit CPUID Maximum Disabled for Windows XP

SATA Ports (0‐3) DeviceNames if Present andEnabled.

Advanced

SATA Port0SATA Port1

SATA Controller(s)

Configure SATA as

Misc Configuration for hard disk

Not PresentNot Present

[Enabled]

Serial-ATA Controller(s) Choices: Disabled, Enabled.

Configure SATA as Choices: IDE/AHCI

Enables Legacy USB support. AUTO optiondisables legacy supportif no USB devices areconnect. DISABLEoption will keep USBdevices available onlyfor EFI applications.

Advanced

USB Configuration

USB Devices1 Keyboard

Legacy USB SupportEHCI Hand-off

USB hardware delays aUSB transfer time-outDevice reset time-outDevice power-up delay

[Enabled][Disabled]

[20 sec][20 sec][Auto]

Legacy USB Support Set [Enabled] if you need to use any USB 1.1/2.0 devices in the operating system that

does not support or have any USB 1.1/2.0 drivers installed. Such as DOS and SCO

EHCI Hand-off This is a workaround for OSs without EHCI hand-off support. The EHCI ownership

change should be claimed by EHCI driver.

USB transfer time-out Choices: 1, 5, 10, 20 sec.

Device Reset time-out USB mass storage device starts unit command timeout.

Choices: 10, 20, 30, 40 sec.

Device power-up delay This setting determines the maximum time for USB device will take before reporting

to the controller.

Set Parameters of Serial Port 0 (COMA)

Advanced

Super IO Configuration

Super IO ChipSerial Port 0 ConfigurationSerial Port 1 ConfigurationParallel Port ConfigurationWatch Dog TimerCPU smart fan controlSystem smart fan cont

Winbond W83627EHG

[Disabled][Disabled][Disabled]

Watch Dog Timer This option will determine watch dog timer.

CPU smart fan control This option allows user to enable/disable the control of CPU fan speed by changing

the fan voltage.

System smart fan control This option allows user to enable/disable the control of smart fan speed by changing

the fan voltage.

Enable or Disable Serial Port (COM)

Advanced

Serial Port 0 Configuration

Serial PortDevice Settings

Change Settings

[Enabled]IO=3F8h; IRQ=4;

[IO=3F8h; IRQ=4;]

Serial Port Use this option to enable or disable the serial port.

Device Settings Use this option to show the serial port IO port address and interrupt address. Change Settings Use this option to change the serial port IO port address and interrupt address.

Advanced

Change SettingsDevice Mode

[Enabled]IO=2F8h; IRQ=3;

[IO=2F8h; IRQ=3;][Serial Port Functi…]

Serial Port Use this option to enable or disable the serial port.

Device Settings Use this option to change the device address and interrupt address. Change Settings Use this option to change the serial port IO port address and interrupt address.

Device Mode Serial mode function.

Enable or Disable Parallel Port (LPT/LPTE)

Advanced

Parallel Port Configuration

Parallel PortDevice Settings

Change SettingsDevice Mode

[Enabled]IO=378h; IRQ=7;

[IO=378h; IRQ=7;][Printer Mode]

Parallel Port Use this option to enable or disable the parallel port. Change Settings Use this option to change the serial port IO port address and interrupt address. Device Mode Printer mode.

Advanced

Pc Health Status

SYSTEM TemperatureCPU TemperatureCPU FAN SpeedSYSTEM FAN SpeedCPUVCORE+12 V+1.5 V+5 V+3.3 VVBAT (V)3.3VSB (V)

: +32 : +29 : 8437: N/A: +1.00: +12.09: +1.54: +5.12: +3.32: +3.00: +3.20

VVVVVVV

Second IO Configuration

Second IO Fintek F81216

Set Parameters of Serial Port 1 (COMC)

Advanced

Serial Port 1 ConfigurationSerial Port 2 ConfigurationSerial Port 3 ConfigurationSerial Port 4 Configuration

Serial Port 1 Configuration Serial Port 2 Configuration Serial Port 3 Configuration Serial Port 4 Configuration

Advanced

Change Settings

[Enabled]Reset Required

[IO=3E8h; IRQ=5;]

Serial Port Use this option to enable or disable the serial port. Change Settings Use this option to change the serial port IO port address and interrupt address.

Advanced

Change Settings

[IO=2E8h; IRQ=5;]

Advanced

Change Settings

[IO=3E0h; IRQ=5;]

Advanced

Change Settings

[IO=2E0h; IRQ=5;]

2.15 Chipset

Host Bridge Parameters

Host BridgeSouth Bridge

Host Bridge South Bridge

Config Memory Frequencyand Timing Settings.

Chipset

Memory Frequency and TimingIntel IGD Configuration

******* Memory Information *******Memory Frequency 800MHZ(DDR3)Total Memory 4096 MBDIMM#0 4096 MBDIMM#0 Not Present

Memory Frequency and Timing Intel IGD Configuration

Enabled OR disabled MRCfast boot.

Chipset

Memory Frequency and Timing

MRC Fast BootMax TOLUD

[Enabled][Dynamic]

MRC Fast Boot Choices: Disabled, Enabled. Max TOLUD This item allows you to select the size of TOLUD.

Select the video Devicewhich will be activatedduring POST. This hasno effect if externalgraphics present

Chipset

Intel IGD ConfigurationIGFX – Boot TypeActive LFPLCD Panel TypeFixed Graphics Memory

BackLight Control (INV1)Backlight Active ModeBacklight Voltage LevBacklight Control Lev

BackLight Control (INV2)Backlight Active ModeBacklight Voltage LevBacklight control Lev

[CRT + LVDS][LVDS-18][1024x768 18 Bit LVDS][128MB]

[DC Mode][+3.3V][Step 6]

IGFX-Boot Type It is the option to select device by the system when it boots.

Backlight Active Mode Choices: PWN Mode, DC Mode. Backlight Voltage Lev Choices: +3.3V, +5V

Backlight Control Lev Choices: Step1, Step2, Step3, Step4, Step5, Step6, Step7, Step8, Step9, Step10.

Enabled/Disable Intel(R)IO Controller Hub (TPT)devices

Chipset

TPT DevicesPCI Express Root Port 0PCI Express Root Port 1

High Precision Event Timer ConfigurationHigh Precision Timer [Enabled]

PCI Express Root Port0 PCI Express Root Port1 High Precision Event Timer Configuration High Precision Timer Choices: Disabled, Enabled.

Azalia Controller

Chipset

Azalia Controller

Select USB ModeUHCI #1 (ports 0 andUHCI #2 (ports 2 andUHCI #3 (ports 4 andUHCI #4 (ports 6 andUSB 2.0(EHCI) Support

SMBus Controller

[HD Audio]

[By Controllers][Enabled][Enabled][Enabled][Enabled][Enabled]

[Enabled]

Select USB Mode Select USB mode by controllers.

UHCI #1 Choices: Disabled, Enabled.

USB 2.0 (EHCI) Support Choices: Disabled, Enabled.

SMBus Controller Choices: Disabled, Enabled.

Enable / Disable PCIExpress Root Port 0.

Chipset

PCI Express Port 0Port 0 IOxAPIC

[Enabled][Disabled]

PCI Express Port0 Choices: Disabled, Enabled.

Port0 Choices: Disabled, Enabled.

Enable / Disable PCIExpress Root Port 1

Chipset

PCI Express Port 1Port 0 IOxAPIC

[Auto][Disabled]

PCI Express Port1 PCI Express function is set automatically.

Port0 Choices: Disabled, Enabled.

2.22 Boot Configuration

Number of seconds to wait for setup activation key.65535(0xFFFF) means indefinite waiting.

Boot ConfigurationSetup Prompt TimeoutBootup NumLock State

Quiet Boot

CSM16 Module Version

GateA20 ActiveOption ROM MessagesInterrupt 19 CaptureCSM Support

Boot Option Priorities

[Disabled]

[Upon Request][Force BIOS][Enabled][Enabled]

Setup Prompt Timeout This setting is to remind when the system is waiting for setup activation key. Bootup NumLock State This setting is to set Num Lock status when the system is powered on.

Setting to [On] will turn on the Num Lock key when the system is powered on.

Setting to [Off] will allow users to use the arrow keys on the numeric keypad.

Choices: On, Off. Quiet Boot This item can help to select the screen display when the system boots.

GateA20 Active Upon request GA20 can be disabled using BIOS services.

Option ROM Messages Set display mode for option ROM.

Interrupt 19 Capture Enable: Allow option ROMs to trap into 19.

CSM Support Enable: Set mode for option CSM.

2.23 Password Description

Password Description

If ONLY the Administrator’s password is set ,then this only limits access to Setup and isonly asked for when entering Setup.If ONLY the User’s password is set, then thisis a power on password and must be entered toboot or enter Setup. In Setup the User willhave Administrator rights.The password length must bein the following range:Minimum length 3Maximum length 20

Administrator PasswordUser Password

Set Administrator Password

Enter : Select+/- : Change Opt .F1: General HelpF2: Previous ValuesF3: Optimized DefaultsF4: Save ESC: Exit

2.24 Save Changes and Exit

Save Changes and ExitDiscard Changes and ExitSave Changes and ResetDiscard Changes and Reset

Save OptionsSave ChangesDiscard Changes

Restore DefaultsSave as User DefaultsRestore User Defaults

Boot Overrode

Exit system setup after saving the changes.

Chapter 3 Drivers Installation

This chapter introduces driver installation information.

Please insert the utility CD to CD-ROM drive, the install menu will appear

automatically, if the install menu do not list suitable driver of Operate System or

appear automatically, please select corresponding driver of utility CD to install.

The Windows XP driver installation steps are as below.

3.1 Intel Chipset Device Software

Step 1. Click “Next” to continue.

Step 2. Read the License Agreement and click “Yes” to continue.

Step 4. Click “Finish” to complete setup.

3.2 Intel Graphic Media Accelerator Driver

Step 2. Click “No” to continue.

Step 4. Choose “Don’t install this driver software” to continue.

3.3 LAN Driver

Step 2. Click “Install” to continue.

3.4 Audio Driver Step 1. Click “Next” to continue.

Appendix-A Watchdog

The working algorithm of the WDT function can be simply described as a counting

process. The time-out Interval can be set through software programming. The

availability of time-out interval is set by software.

The System Board allows users control WDT through dynamic software programming.

The WDT starts counting when it is activated. It sends out a signal to system reset,

when time-out interval ends. To prevent the time-out interval from running out, a

re-trigger signal will need to be sent before the counting reaches its end. This action

will restart the counting process.

WDT program should keep the counting process running under normal condition.

WDT should never generate a system reset unless the system runs into troubles.

The related Control Registers of WDT are all included in the following sample

program that is written in C language. User can fill a non-zero value into the Time-out

Value Register to enable/refresh WDT. System will be reset after the Time-out Value

to be counted down to zero. Or user can directly fill a zero value into Time-out Value

Register to disable WDT immediately.

To ensure a successful accessing to the content of desired Control Register, the

sequence of following program codes should be step-by-step run again when each

register is accessed.

For more information about WDT, please refer to Winbond W83627EHF data sheet.

There are two PnP I/O port addresses that can be used to configure WDT,

1) 0x2E: EFIR (Extended Function Index Register, for identifying CR index number)

2) 0x2F: EFDR (Extended Function Data Register, for accessing desired CR)

Below are some example codes, which demonstrate the use of WDT.

// Enter Extended Function Mode

outp(0x002E, 0x87);

// Assign Pin 77 to be a WDTO# Signal

outp(0x002E, 0x2D);

outp(0x002F, inp(0x002F) & 0xFE);

// Select Logic Device 8

outp(0x002E, 0x07);

outp(0x002F, 0x08);

// Active Logic Device 8

outp(0x002E, 0x30);

outp(0x002F, 0x01);

//Clear WDTO# Status

outp(0x002E, 0xF7);

outp(0x002F, inp(0x2F) & 0xEF);

// Select Count Mode (Second / Minute)

outp(0x002E, 0xF5);

outp(0x002F, (inp(0x002F) & 0xF7) | ( Count-mode Register & 0x08));

// Set Time-out Value

outp(0x002E, 0xF6);

outp(0x002F, Time-out Value Register );

// Exit Extended Function Mode

outp(0x002E, 0xAA);

Definitions of Variables: Value of Count-mode Register :

1) 0x00 -- Count down in seconds (Bit3=0)

2) 0x08 -- Count down in minutes (Bit3=1)

Value of Time-out Value Register :

1) 0x00 -- Time-out Disable

2) 0x01~0xFF -- Value for counting down

Appendix-B GPIO

The System Board provides 4 dedicated output ports and 4 programmable I/O ports

that can be individually configured to perform a simple I/O function. Users can

configure 4 programmable I/O ports to become an input or output port by

programming register bit of I/O Selection .To invert port value, the setting of Inversion

Register has to be made (Note). Port values can be set to read or write through Data

Register.

Note: Only 4 programmable I/O ports support.

Additionally, 4 Digital Output ports amplified signals from GPIO ports. There are

open-drain buffers, which can offer greater driving capacity up to 100mA.

For more information about GPIO, please refer to Winbond W83627EHF data sheet.

The related Control Registers of GPIO are all included in the following sample

program that is written in C language. To ensure a successful accessing to the

content of desired Control Register, the sequence of following program codes should

be step-by-step run again when each register is accessed.

There are two PnP I/O port addresses that can be used to configure GPIO ports,

1) 0x2E - EFER (Extended Function Enable Register, for entering Extended Function

- EFIR (Extended Function Index Register, for identifying CR index number)

2) 0x2F - EFDR (Extended Function Data Register, for accessing desired CR)

Below are some example codes, which demonstrate the use of GPIOs.

// Enter Extended Function Mode

outp(0x002E, 0x87);

// Assign Pin121-128 to be GPIO port

outp(0x002E, 0x29);

outp(0x002F, inp(0x002F) | 0x01);

// Select Logic Device 7

outp(0x002E, 0x07);

outp(0x002F, 0x07);

// Active Logic Device 7

outp(0x002E, 0x30);

outp(0x002F, 0x01);

// Select Inversion Mode

outp(0x002E, 0xF2);

outp(0x002F, (inp(0x002F) & 0x3C) | ( Inversion Register & 0xC3));

// Select I/O Mode

outp(0x002E, 0xF0);

outp(0x002F, (inp(0x002F) & 0x3C) | ( I/O Selection Register & 0xC3));

// Access GPIO ports

outp(0x002E, 0xF1);

outp(0x002F, (inp(0x002F) & 0x3C) | ( Output Data & 0xC3));

Input Data = inp(0x002F);

// Exit Extended Function Mode

outp(0x002E, 0xAA);

Definitions of Variables: Each bit in the lower nibble of each Register represents the setting of a GPIO port.

Super IO Pin Bit GPIO DIO 128 0 GPIO DIO-Out0

127 1 GPIO DIO-Out1

126 2 GPIO DIO-In0

125 3 GPIO DIO-In1

124 4 GPIO DIO-In2

123 5 GPIO DIO-In3

122 6 GPIO DIO-Out2

121 7 GPIO DIO-Out3

Value of Inversion Register :

When set to a ‘1’, the incoming/outgoing port value is inverted.

When set to a ‘0’, the incoming/outgoing port value is the same as in Data

Register.

Value of I/O Selection Register :

When set to a ‘1’, respective GPIO port is programmed as an input port.

When set to a ‘0’, respective GPIO port is programmed as an output port.

Value of Output Data / Input Data :

If a port is assigned to be an output port, then its respective bit can be

read/written.

If a port is assigned to be an input port, then its respective bit can be read only.

DIO_IN0/DIO_IN1/DIO_IN2/DIO_IN3 is programmed as Inputs by BIOS default.

Parameter Conditions

VinH min +1.857V

VinL max +0.525V

Rated Vin -8V ~ +12V

NC Status High by Default

** Attention: If DIO_IN0/DIO_IN1/DIO_IN2/DIO_IN3 is programmed as Output signal, they can only offer a normal signal transfer (NOT amplified signals).

VoutH 3.3V thru 10k

VoutL 0V thru 1k

DIO_OUT0/DIO_OUT1/DIO_OUT2/DIO_OUT3 is fixed as Outputs by BIOS.

Open-drain buffer Power-on default = Open

Driving Capacity max 100mA continue

industrial computer industrial motherboard wmix-n26006 manual … · 2015. 4. 3. · chapter 2 bios...

Documents

embedded & industrial computing - lanner3 about about...

embedded intel® atom™ processor · the product brief and...

hp mini 2001 product description category description...

ipw10id3s-h1-poe-pct€¦ · the ais 10.1” multi-touch...

jetbox 8312 user manual - plcsystems.ru · 2017-05-24 ·...

dn2800mt - asrock · 9~19v dc-in (2-pin pwr ... intel®...

industrial computer industrial motherboard wmix-qm770 user...

features - advantech...fanless embedded box pcs features...

mio-5250 intel atom™ n2600/ d2550, 3.5...

association of experimental rocketry of the pacific...

hp mini 210, hp mini 110, compaq mini cq10h10032. mini 110...

wmix-e38451 quick installation guide 20141011 · 2015. 4....

mio-5250 mi/o-compact sbc, intel atom™ n2600 /...

8.4” industrial panel pc ppc-3708a-n26 ppc-3708a …......

specifications - advantech · 2016-08-25 · aimb-214...

10.4 industrial panel pc ppc-3710a-n26 intel® atom ......

pico-itx board pico-cv01 -...

qseven cpu module - eftwee.nl...1 x emq-i2506 qseven cpu...

mio-2261 sales kit mi/o-ultra (pico-itx sbc) intel atom...

getac e110 fully rugged tablet - animal systems · 10.1"...