in the format proie y the authors an uneite. atomic resolution of … · 2017-12-19 · in the...
Post on 18-Jan-2020
2 Views
Preview:
TRANSCRIPT
-
In the format provided by the authors and unedited.
1
Atomic Resolution of Structural Changes in Elastic Crystals Anna Worthy,1* Arnaud Grosjean,2* Michael C. Pfrunder,2 Yanan Xu,1 Cheng Yan,1 Grant Edwards,3 Jack K. Clegg2 and John C. McMurtrie1 1 School of Chemistry, Physics and Mechanical Engineering, Faculty of Science and Engineering, Queensland
University of Technology, GPO Box 2434, Brisbane, QLD, 4001
2 School of Chemistry and Molecular Biosciences, The University of Queensland, St Lucia, QLD, 4072, Australia
3 Australian Institute of Bioengineering and Nanotechnology, The University of Queensland, St Lucia, QLD, 4072,
Australia
Supplementary Information
Contents 1. Synthesis bis(acetylacetonato)copper(II) 2
2. Nanoindentation studies 2
S2a. Calculation of stiffness (S), contact depth (hc), hardness (H) and reduced modulus (Er)’ 2
S2b. Nanoindentation data obtained for the [101] face 3
S2c. Indentation data obtained for the [𝟏𝟏01] face 6
3. Tensile Strength Tests 11
4. 3-Point Bend Tests 15
5. Powder X-Ray Diffraction 18
6. Single Crystal X-ray Diffraction 19
7. Other Flexible Crystals 28
8. Supplementary References 31
Atomic resolution of structural changes in elastic crystals of copper(ii) acetylacetonate
© 2017 Macmillan Publishers Limited, part of Springer Nature. All rights reserved.
SUPPLEMENTARY INFORMATIONDOI: 10.1038/NCHEM.2848
NATURE CHEMISTRY | www.nature.com/naturechemistry 1
http://dx.doi.org/10.1038/nchem.2848
-
2
1. Synthesis of bis(acetylacetonato)copper(II) Acetylacetone was purchased and used without purification. The complex was prepared by the method of Holtzclaw
and Collman [1]. Blue acicular crystals were grown by dissolving the complex in chloroform and allowing the solvent
to evaporate slowly. Elemental Analysis Found: C, 45.80; H, 5.39%. Calc. for C10H14O4Cu: C, 45.88; H, 5.39%.
2. Nanoindentation Studies
Nanoindentation measurements were collected on a Hysitron TI 950 TriboIndenter system with a TE1017207
Berkovich probe on fused quartz indenter (three-sided pyramidal indenter with tip radius approximately 100nm,
142.3° total included angles). Indents were typically performed under the load-control setting with a 10s loading
period and a 10s unloading period. Samples were adhered to metal sample disks with superglue. Flat areas on a
crystals surface suitable for indentation were determined by the fine focusing of the on-board camera. To determine
truly representative values for the elastic (Young) modulus and hardness multiple indents were performed on a
number of sites on a single crystal, and several crystals were tested in the same way for each face. The elastic modulus
and hardness were calculated with TriboScan 9 software using the equations given [2].
2a. Calculation of stiffness (S), contact depth (hc), hardness (H) and reduced modulus (Er)
The curve was fit using the power law relation:
𝑃 = 𝐴(ℎ − ℎ()*
The derivative of the power law relation (with respect to ℎ) was evaluted at the maximum load to calculate the contact stiffness, 𝑆.
The contact depth, ℎ,, was calculated with:
ℎ, = ℎ*-. − 0.75×𝑃*-.𝑆
Where ℎ*-. is given as maximum depth and 𝑃*-. is given as maximum force.
The hardness,𝐻, was calculated with:
𝐻 =𝑃*-.𝐴(ℎ,)
Where 𝐴(ℎ,) is given as contact area.
The reduced modulus, 𝐸7, was calculated with:
𝐸7 =𝜋
2 𝐴(ℎ,)×𝑆
-
3
2b. Nanoindentation data obtained for the [101] face
Supplementary Figure 1. To obtain a representative value for the elastic modulus and surface hardness of the [101] face of the crystals, multiple indents were performed at various sites along each of three different crystals. The elastic modulus of the [101] surface was determined to be between 4.8 and 6.9 GPa. The hardness which was measured simultaneously was found to be between 197.7 and 242.9 MPa.
-
4
Supplementary Table 1. The elastic modulus (GPa) and hardness (MPa) from each indent on crystals 1-3 for the [101] face.
Crystal Indent Er (GPa) H (MPa)
1
1_1_3 7.13 240.57 1_1_5 7.5 254.26 1_2_1 6.99 223.91 1_2_2 6.63 242.3 1_2_3 6.68 237.3 1_5_1 6.69 246.59 1_5_2 6.72 255.38 AVERAGE 6.91 242.90
2
3_2_1 5.38 228.83 3_2_2 5.33 218.35 3_2_3 5.43 222.44 3_2_4 5.41 236.64 3_7_1 5.32 230.6 3_7_2 5.42 235.34 3_7_3 5.15 217.43 AVERAGE 5.35 227.09
3
5_2_1 4.91 194.7 5_2_2 4.83 204.12 5_2_3 4.59 196.33 5_2_4 4.71 203.27 5_1_1 5.01 207.03 5_1_2 4.69 184.06 5_1_3 4.71 189.78 5_1_4 4.76 201.17 5_1_5 4.9 198.55
AVERAGE 4.79 197.67
-
5
Supplementary Figure 2. Images of each site on each crystal where indenting was performed on the [101] face. Indents are identifiable as triangular impressions on surface.
-
6
2c. Indentation data obtained for the [𝟏01] face
Supplementary Figure 3. As in investigation of the surface properties of the [101] face (3b), multiple indentations of the [101] face were performed at a number of sites on each of three crystals in order to obtain representative values of the elastic modulus and hardness. Note that crystals 1-3 in the [101] experiments (3c) are not the same crystals labelled 1-3 in the [101] face measurements (3b).
-
7
Supplementary Table 2. The elastic modulus (GPa) and hardness (MPa) from each indent on crystals 1-3 for the [101] face.
Crystal Indent Er (GPa) H (MPa)
1
2_2_1 9.26 339.05 2_2_2 10.29 374.12 2_2_3 9.63 347.93 2_2_4 10.3 390.84 2_2_7 9.28 365.39 2_3_1 12.42 407.13 2_3_2 12.33 401.5 2_3_3 11.05 363.42 2_3_4 10.29 344.37 2_5_1 13.33 415.07 2_5_2 12.52 427.03 2_5_3 12.42 409.69 2_5_4 14.34 401.07 AVERAGE 11.34 383.59
2
3_1_1 13.61 390.38 3_1_2 14.1 423.08 3_1_3 13.67 399.26 3_2_1 13.22 428.94 3_2_2 12.5 378.87 3_2_3 12.15 417.59 3_3_1 13.57 403.68 3_3_2 13.43 364.51 3_3_3 14.45 419.59 AVERAGE 13.41 402.88
3
2_5_1 13.05 377.86 2_5_2 14.21 402.76 2_5_3 15.28 405.05 2_5_4 14.83 403.87 2_6_1 14.36 394.5 2_6_2 13.85 383.51 2_6_3 13.4 378.35 2_7_1 14 401.05 2_7_2 12.84 364.26 2_7_3 12.52 329.12 AVERAGE 13.83 384.03
-
8
Supplementary Figure 4. Images of each site on three crystals where indenting was performed on the [101] face. Indents are evident as triangular impressions on surface.
-
9
Hardness vs Elastic Modulus of [Cu(acac)2]
Supplementary Figure 5. A plot of elastic modulus vs surface hardness of [Cu(acac)2] showing results for each indent on the [101] and [101] faces (listed in Supplementary Tables 1 and 2).
-
10
3. Tensile Strength Tests Tensile stress was measured using a Tytron 250 Microforce Testing System with a displacement resolution of 0.1 µm
and a load resolution of 1 µN. Responses were obtained in displacement controlled mode at a rate of 5 mm/min, and a
data acquisition rate of 1 point/0.00944 s. The samples were fixed with the 250-N Mechanical Clamp Grip and
double-sided tape was placed between grip and sample to minimise slippage during testing. During the mechanical
testing, load (F) and displacement (d) were recorded in real time.
𝐸𝑙𝑎𝑠𝑡𝑖𝑐 𝑌𝑜𝑢𝑛𝑔F𝑠 𝑀𝑜𝑑𝑢𝑙𝑢𝑠(𝐸) = 𝑆𝑡𝑟𝑒𝑠𝑠𝑆𝑡𝑟𝑎𝑖𝑛
𝑆𝑡𝑟𝑒𝑠𝑠(𝑀𝑃𝑎) = 𝐹𝐴=
𝐴𝑝𝑝𝑙𝑖𝑒𝑑𝑓𝑜𝑟𝑐𝑒𝐶𝑟𝑜𝑠𝑠 − 𝑠𝑒𝑐𝑡𝑖𝑜𝑛𝑎𝑙𝑎𝑟𝑒𝑎
𝑆𝑡𝑟𝑎𝑖𝑛 = ∆𝐿𝐿= 𝐶ℎ𝑎𝑛𝑔𝑒𝑖𝑛𝑙𝑒𝑛𝑔𝑡ℎ𝐼𝑛𝑖𝑡𝑎𝑙𝑙𝑒𝑛𝑔𝑡ℎ
Supplementary Figure 6. Tensile strength testing was performed on a Tytron 250 Microforce Testing System (MTS). Tensile (pulling) strain was applied to the sample and applied load was measured over a fixed length of displacement. Double sided adhesive tape was used to fix the crystals in the clamps to avoid slippage.
-
11
Supplementary Table 3. The raw data collected from the MTS instrument as a function of load vs displacement. The equations (above) were used to calculate the stress and strain the sample was subjected to. From this the elastic modulus of the sample was determined from the slope of the initial linear region of the stress-strain curve. The fracture strength is the point at which the crystal breaks (observed as a sudden drop in stress).
Crystal Width (mm) Height (mm) Length (between clamps) (mm)
Elastic Modulus (MPa)
Fracture Strength (MPa)
1 (190115_sample3_doublesidedtape) 0.576 0.0961 11.17 209.7 9.8 2 (030215_sample2_1) 0.531 0.257 19.00 258.2 7.9 3 (030215_sample4_1) 0.346 0.153 12.43 390.3 13.3 4 (030215_sample3_3) 0.234 0.174 4.18 548.5 21.5
-
12
Supplementary Figure 7. The dimensions (height and width) of each crystal subjected to tensile strength were measured using an optical microscope. The average of these measurements for each crystal was used to determine cross sectional area of that crystal in the calculations of stress and strain.
-
13
The stress~strain (σ~ε) curve obtained for each crystal subjected to the tensile test is shown in Supplementary Figure 8. From these curves, we can see that these samples deform elastically initially and then plastic deformation appears followed by a complete fracture. The estimated fracture strength σs ranges from 7.5 MPa to 13.0 MPa. Elastic moduli were calculated using the slope of the initial linear sections of the σ~ε curve. The estimated elastic modulus is in the range 209.3 MPa to 390.5 MPa.
Supplementary Figure 8. The initial approximately linear regions of the stress-strain curves of four crystals gave elastic moduli between 0.21 and 0.55 GPa. Stress is given in MPa while strain is a unitless number.
-
14
S4. 3-Point Bend Tests Three-point bend tests were conducted at room temperature using an Instron Model 5543 universal testing machine with a capacity of 5-N load cell and 3-point bending apparatus with a 15 mm span. A crosshead speed of 2 mm/min was applied for the tests.
The individual and average results for 6 [Cu(acac)2] crystals were determined.
Supplementary Figure 9. Crystals of [Cu(acac)2] were subject to 3-point bend testing in order to determine their flexural strength. The crystals rested on two pins and a load was applied at a vector normal to the crystal surface as shown.
𝑆𝑡𝑟𝑒𝑠𝑠 =3×𝐹𝑜𝑟𝑐𝑒×𝐿S
2×𝑤𝑖𝑑𝑡ℎ×ℎ𝑒𝑖𝑔ℎ𝑡U
𝑆𝑡𝑟𝑎𝑖𝑛 = 6×∆𝐿×ℎ𝑒𝑖𝑔ℎ𝑡
𝐿U
𝐸𝑙𝑎𝑠𝑡𝑖𝑐𝑀𝑜𝑑𝑢𝑙𝑢𝑠 = 𝑆𝑡𝑟𝑒𝑠𝑠𝑆𝑡𝑟𝑎𝑖𝑛
Supplementary Table 4. The 3-point bend data is given as a change in load with increasing displacement. The stress and strain applied to the sample was calculated from the equations above using crystal dimensions measured on an optical microscope.
Sample b (mm) d (mm) L (mm)
Elastic Modulus (GPa)
Fractural Strength (GPa)
3-pb3 0.467 0.122 15 7.99 68.7 3-pb4 0.428 0.167 15 4.39 46.4 3-pb5 0.533 0.212 15 1.98 5.4 3-pb6 0.441 0.204 15 2.9 33.2 3-pb7 0.321 0.206 15 3.94 47.2 3-pb8 0.316 0.068 15 7.03 28.2
-
15
Supplementary Figure 10. Stress-strain curves of six crystals [Cu(acac)2] resulted in elastic moduli in the range 2-8 GPa.
Supplementary
Supplementary Figure 11. The elastic modulus is given by the slope of the initial linear region of the stress-strain curve, seen here (brown) for crystal 3-pb3.
0
10
20
30
40
50
60
70
80
90
0 0.5 1 1.5 2 2.5 3
Stress(M
Pa)
Strain(%)
3-pb3
3-pb5
3-pb4
3-pb7
3-pb8
3-pb6
y=7998.1x+1.4257R²=0.9961
0
10
20
30
40
50
60
70
80
90
0 0.01 0.02 0.03
Stress(M
Pa)
Strain
-
16
Supplementary Figure 12a. The dimensions of each crystal used in 3-point bend tests were measured using an optical microscope. The average dimensions for each crystal were used in the calculations of stress and strain for that crystal.
-
17
Supplementary Figure 12b. Crystal dimensions of 3-point bend tests continued.
-
18
5. Powder X-Ray Diffraction The powder X-ray diffraction pattern for [Cu(acac)2] was collected on a PANalytical X’Pert PRO MDP with graphite-
monochromated Cu radiation Kα= 1.5405980Å. The experimental pattern was compared to the pattern simulated
from a single-crystals X-ray structure in order to confirm structural purity.
Supplementary Figure 13. The powder X-ray diffraction patterns collected from [Cu(acac)2] crystals grown from CHCl3 (brown) and simulated from a SCXRD structure (blue) which was collected from a crystal on an Oxford Diffraction Gemini S Ultra home source diffractometer.
-
19
6. Single Crystal X-ray Diffraction Crystal structure mapping was achieved by using a micro-focused X-ray beam available at the Australian Synchrotron
MX beamlines. All measurements were performed at 100(2) K and with the wavelength: λ = 0.7108 Å. Three single
acicular crystals of [Cu(acac)2] were used for these studies (Supplementary Figure 15). One unbent crystal (crystal
0) was used as a reference for the undistorted crystal structure and two crystals (crystal 1 and 2) were bent in to loops
(as shown in Supplementary Figure 14) with radius of curvature of 1.2 mm and 3.2 mm, respectively. A full data
collection was performed for crystal 0 at the MX1 beamline with a beam cross-section (at full width at half
maximum) of 120 by 120 µm. Data collections for crystal 1 and 2 were performed at the MX2 beamline using a
micro-collimator producing a beam cross-section of 7.5 by 11.25 µm. For each crystal (1 and 2), a series of 10° φ
scans with a 0.5° step were performed at intervals every 5 µm along the bent cross-section of the crystal as shown in
Supplementary Figure 15. This allowed collection of sufficient X-ray data for structure refinement at 16 locations on
the transect from the outside of the loop to the inside for crystal 1 (data sets crystal 1(a-p)) and 18 locations on the
transect for crystal (data sets crystal 2(a-r)). Thus it was possible to map and compare the crystal structure at each
interval on the transect with the structure of the unbent crystal (crystal 0) and to determine the structural differences
resulting from expansion (outside of loop) and compression (inside of loop).
Data acquisition was performed using the Blu-Ice software [3]. Data integration was performed using the XDS
package software [4]. Using Olex2 graphical interface [5], the structure of crystal 0 was solved with the ShelXT [6]
and refined with the ShelXL [7]. Using the Olex2 interface [5], all the structures on transects of crystal 1 and crystal
2 were refined based on the structure solution for crystal 0 using ShelXL [7] with isotropic displacement parameters
so as to maintain reasonable data to parameter ratios. The isotropic refinement and limited number of diffraction
images collected for the mapping studies results in a number of Alert As and Alert Bs.
The crystal structure of crystal 0 was used to calculate variations in the unit cell parameters of crystal 1 and crystal 2
along the mapped transects. The zero position on the plots (Supplementary Figures 18 and 19) corresponds to the
interval on the transect of the bent crystal at which the unit cell parameters most closely match those of the unbent
crystal. The deformations of the crystal were then determined for the natural faces of the crystals by face indexing
(Supplementary Figures 20 and 21).
Based on these refined crystal structures key structural variations such as the angle between the plane of the
[Cu(acac)2] molecules and the (010) plane as well as the distance between the centroids of two adjacent molecules
were analysed (Supplementary Figures 22, 23 and 24).
-
20
Supplementary Figure 14. A series of single crystal x-ray diffraction patterns collected along the arc of a bent crystal
reveal that, as the curvature of the bend increases the Bragg peaks broaden.
Supplementary Figure 15. Crystals of [Cu(acac)2] used for crystal structure mapping: a) unbent crystal (reference
material); b) bend crystal 1; b) bend crystal 2. The arrows show the direction of the mapping.
Crystal Data for crystal 0 (C10H14CuO4, M =261.75 g/mol): monoclinic, space group P 21/n (no. 14), a = 10.277(2) Å,
b = 4.6430(9) Å, c = 11.285(2) Å, β = 92.48(3)°, V = 537.97(19) Å3, Z = 2, T = 100(2) K, µ(Synchrotron) = 2.020 mm-
1, Dcalc = 1.616 g/cm3, 9036 reflections measured (7.23 ≤ 2Θ ≤ 57.324 ), 1371 unique (Rint = 0.0535, Rsigma = 0.0309).
The final R1 was 0.0382 (I > 2σ(I)) and wR2 was 0.1086 (all data).
-
21
Supplementary Tables 5 a b and c. Crystal data for each interval (a-p) on the mapped transect of crystal 1.
a)
Interval on Transect of Loop Crystal data a b c d e f
a/Å 10.225(2) 10.231(2) 10.238(2) 10.250(2) 10.268(2) 10.264(2) b/Å 4.7080(9) 4.7000(9) 4.6910(9) 4.6830(9) 4.6740(9) 4.6640(9) c/Å 11.187(2) 11.191(2) 11.211(2) 11.213(2) 11.227(2) 11.249(2) β/° 93.01(3) 92.95(3) 92.85(3) 92.77(3) 92.56(3) 92.60(3)
Volume/Å3 537.79(19) 537.41(19) 537.76(19) 537.61(19) 538.28(19) 537.95(19) ρcalc/g cm-3 1.616 1.618 1.617 1.617 1.615 1.616
µ/mm-1 2.021 2.022 2.021 2.021 2.019 2.02 2Θ range for data collection/° 19.332 to
59.146 19.336 to
59.216 19.34 to 59.242
19.338 to 59.254
19.34 to 59.152
19.346 to 59.088
Reflections collected 299 293 287 285 284 285 Independent reflections 299 293 287 285 284 285
Data/restraints/parameters 299/0/32 293/0/32 287/0/32 285/0/32 284/0/32 285/0/32 Goodness-of-fit on F2 1.138 1.103 1.115 1.098 1.108 1.07
Final R indexes [I≥2σ (I)] R1 = 0.0896, wR2 = 0.1516
R1 = 0.0641, wR2 = 0.1556
R1 = 0.0619, wR2 = 0.1464
R1 = 0.0563, wR2 = 0.1268
R1 = 0.0578, wR2 = 0.1269
R1 = 0.0537, wR2 = 0.1101
Final R indexes [all data] R1 = 0.1839, wR2 = 0.1942
R1 = 0.0880, wR2 = 0.1740
R1 = 0.0750, wR2 = 0.1597
R1 = 0.0641, wR2 = 0.1338
R1 = 0.0637, wR2 = 0.1313
R1 = 0.0591, wR2 = 0.1137
Largest diff. peak/hole / e Å-3
0.37/-0.41 0.39/-0.41 0.37/-0.47 0.41/-0.49 0.41/-0.45 0.40/-0.47
b)
Interval on Transect of Loop Crystal data g h i j k l
a/Å 10.271(2) 10.275(2) 10.278(2) 10.283(2) 10.292(2) 10.301(2) b/Å 4.6540(9) 4.6430(9) 4.6290(9) 4.6180(9) 4.6050(9) 4.5940(9) c/Å 11.269(2) 11.286(2) 11.318(2) 11.334(2) 11.360(2) 11.380(2) β/° 92.46(3) 92.43(3) 92.33(3) 92.26(3) 92.17(3) 92.07(3)
Volume/Å3 538.17(19) 537.93(19) 538.03(19) 537.80(19) 538.02(19) 538.18(19) ρcalc/g cm-3 1.615 1.616 1.616 1.616 1.616 1.615
µ/mm-1 2.019 2.02 2.02 2.021 2.02 2.019 2Θ range for data collection/° 19.352 to
59.056 19.356 to
58.956 19.368 to
59.214 19.374 to
59.128 19.376 to
59.166 18.568 to
59.028 Reflections collected 281 281 283 282 286 282
Independent reflections 281 281 283 282 286 282 Data/restraints/parameters 281/0/32 281/0/32 283/0/32 282/0/32 286/0/32 282/0/32
Goodness-of-fit on F2 1.126 1.145 1.135 1.157 1.107 1.132 Final R indexes [I≥2σ (I)] R1 = 0.0526,
wR2 = 0.1146 R1 = 0.0495, wR2 = 0.1011
R1 = 0.0540, wR2 = 0.1180
R1 = 0.0510, wR2 = 0.1055
R1 = 0.0517, wR2 = 0.1095
R1 = 0.0554, wR2 = 0.1373
Final R indexes [all data] R1 = 0.0586, wR2 = 0.1194
R1 = 0.0549, wR2 = 0.1047
R1 = 0.0599, wR2 = 0.1217
R1 = 0.0564, wR2 = 0.1090
R1 = 0.0560, wR2 = 0.1129
R1 = 0.0621, wR2 = 0.1448
Largest diff. peak/hole / e Å-3
0.38/-0.45 0.37/-0.44 0.38/-0.46 0.38/-0.42 0.41/-0.43 0.37/-0.46
c)
Interval on Transect of Loop Crystal data m n o p
a/Å 10.301(2) 10.305(2) 10.321(2) 10.326(2) b/Å 4.5800(9) 4.5730(9) 4.5630(9) 4.5580(9) c/Å 11.413(2) 11.428(2) 11.444(2) 11.451(2) β/° 91.95(3) 91.94(3) 91.68(3) 91.63(3)
Volume/Å3 538.14(19) 538.23(19) 538.72(19) 538.73(19) ρcalc/g cm-3 1.615 1.615 1.614 1.614
µ/mm-1 2.019 2.019 2.017 2.017 2Θ range for data collection/° 18.62 to
58.914 18.644 to
58.944 18.684 to
58.96 18.702 to
58.982 Reflections collected 282 284 285 286
Independent reflections 282 284 285 286 Data/restraints/parameters 282/0/32 284/0/32 285/0/32 286/0/32
Goodness-of-fit on F2 1.112 1.07 1.163 1.08 Final R indexes [I≥2σ (I)] R1 = 0.0555,
wR2 = 0.1286 R1 = 0.0602, wR2 = 0.1466
R1 = 0.0543, wR2 = 0.1261
R1 = 0.0731, wR2 = 0.1313
Final R indexes [all data] R1 = 0.0640, wR2 = 0.1364
R1 = 0.0710, wR2 = 0.1565
R1 = 0.0735, wR2 = 0.1376
R1 = 0.1779, wR2 = 0.1687
Largest diff. peak/hole / e Å-3
0.43/-0.46 0.46/-0.46 0.31/-0.37 0.28/-0.32
-
22
Supplementary Tables 6 a b and c. Crystal data and structure refinement for crystal 2 mapping.
a)
Interval on Transect of Loop Crystal data a b c d e f
a/Å 10.257(2) 10.259(2) 10.261(2) 10.263(2) 10.266(2) 10.268(2) b/Å 4.6780(9) 4.6730(9) 4.6680(9) 4.6630(9) 4.6590(9) 4.6540(9) c/Å 11.221(2) 11.230(2) 11.242(2) 11.251(2) 11.260(2) 11.268(2) β/° 92.81(3) 92.77(3) 92.72(3) 92.68(3) 92.63(3) 92.61(3)
Volume/Å3 537.76(19) 537.74(19) 537.87(19) 537.84(19) 537.99(19) 537.91(19) ρcalc/g cm-3 1.617 1.617 1.616 1.616 1.616 1.616
µ/mm-1 2.021 2.021 2.02 2.021 2.02 2.02 2Θ range for data collection/° 9.580 to
59.024 9.588 to 59.010
9.596 to 59.028
9.606 to 59.068
9.612 to 58.982
9.620 to 58.974
Reflections collected 319 317 312 309 304 297 Independent reflections 276 275 271 268 264 258
Data/restraints/parameters 276/0/32 275/0/32 271/0/32 268/0/32 264/0/32 258/0/32 Goodness-of-fit on F2 1.078 1.08 1.125 1.109 1.2 1.2
Final R indexes [I≥2σ (I)] R1 = 0.0922, wR2 = 0.2280
R1 = 0.0592, wR2 = 0.1444
R1 = 0.0472, wR2 = 0.1076
R1 = 0.0457, wR2 = 0.0996
R1 = 0.0422, wR2 = 0.0971
R1 = 0.0438, wR2 = 0.0946
Final R indexes [all data] R1 = 0.1365, wR2 = 0.2617
R1 = 0.0727, wR2 = 0.1538
R1 = 0.0545, wR2 = 0.1122
R1 = 0.0516, wR2 = 0.1030
R1 = 0.0466, wR2 = 0.0998
R1 = 0.0469, wR2 = 0.0964
Largest diff. peak/hole / e Å-3
0.48/-0.49 0.27/-0.31 0.27/-0.32 0.27/-0.33 0.29/-0.32 0.30/-0.31
b)
Interval on Transect of Loop Crystal data g h i j k l
a/Å 10.270(2) 10.273(2) 10.276(2) 10.279(2) 10.281(2) 10.285(2) b/Å 4.6500(9) 4.6450(9) 4.6400(9) 4.6330(9) 4.6270(9) 4.6200(9) c/Å 11.282(2) 11.289(2) 11.298(2) 11.311(2) 11.325(2) 11.337(2) β/° 92.55(3) 92.52(3) 92.49(3) 92.43(3) 92.36(3) 92.31(3)
Volume/Å3 538.24(19) 538.17(19) 538.19(19) 538.18(19) 538.28(19) 538.26(19) ρcalc/g cm-3 1.615 1.615 1.615 1.615 1.615 1.615
µ/mm-1 2.019 2.019 2.019 2.019 2.019 2.019 2Θ range for data collection/° 9.626 to
58.966 9.634 to 58.952
9.642 to 58.938
9.654 to 58.928
9.664 to 58.924
9.676 to 58.906
Reflections collected 299 297 299 297 298 301 Independent reflections 260 258 260 259 261 262
Data/restraints/parameters 260/0/32 258/0/32 260/0/32 259/0/33 261/0/32 262/0/32 Goodness-of-fit on F2 1.196 1.175 1.157 1.075 1.104 1.12
Final R indexes [I≥2σ (I)] R1 = 0.0448, wR2 = 0.1001
R1 = 0.0453, wR2 = 0.0973
R1 = 0.0449, wR2 = 0.0962
R1 = 0.0434, wR2 = 0.0928
R1 = 0.0470, wR2 = 0.1108
R1 = 0.0456, wR2 = 0.1015
Final R indexes [all data] R1 = 0.0481, wR2 = 0.1026
R1 = 0.0478, wR2 = 0.0987
R1 = 0.0477, wR2 = 0.0983
R1 = 0.0460, wR2 = 0.0949
R1 = 0.0485, wR2 = 0.1118
R1 = 0.0473, wR2 = 0.1024
Largest diff. peak/hole / e Å-3
0.35/-0.31 0.29/-0.31 0.34/-0.29 0.33/-0.28 0.34/-0.31 0.37/-0.34
c)
Interval on Transect of Loop Crystal data m n o p q r
a/Å 10.287(2) 10.290(2) 10.291(2) 10.293(2) 10.296(2) 10.297(2) b/Å 4.6150(9) 4.6110(9) 4.6070(9) 4.6030(9) 4.5990(9) 4.5960(9) c/Å 11.348(2) 11.357(2) 11.365(2) 11.372(2) 11.380(2) 11.386(2) β/° 92.26(3) 92.22(3) 92.16(3) 92.14(3) 92.10(3) 92.08(3)
Volume/Å3 538.32(19) 538.45(19) 538.44(19) 538.42(19) 538.49(19) 538.49(19) ρcalc/g cm-3 1.615 1.614 1.614 1.615 1.614 1.614
µ/mm-1 2.019 2.018 2.018 2.018 2.018 2.018 2Θ range for data collection/° 9.684 to
58.900 9.690 to 58.888
9.698 to 58.910
9.704 to 58.926
9.710 to 59.070
9.716 to 59.048
Reflections collected 304 310 312 316 322 325 Independent reflections 265 267 269 272 276 279
Data/restraints/parameters 265/0/32 267/0/32 269/0/32 272/0/32 276/0/32 279/0/32 Goodness-of-fit on F2 1.126 1.14 1.154 1.126 1.108 1.08
Final R indexes [I≥2σ (I)] R1 = 0.0436, wR2 = 0.0934
R1 = 0.0468, wR2 = 0.1021
R1 = 0.0475, wR2 = 0.1063
R1 = 0.0493, wR2 = 0.1220
R1 = 0.0608, wR2 = 0.1545
R1 = 0.0612, wR2 = 0.1568
Final R indexes [all data] R1 = 0.0463, wR2 = 0.0955
R1 = 0.0490, wR2 = 0.1035
R1 = 0.0503, wR2 = 0.1077
R1 = 0.0528, wR2 = 0.1251
R1 = 0.0672, wR2 = 0.1607
R1 = 0.0702, wR2 = 0.1659
Largest diff. peak/hole / e Å-3
0.35/-0.31 0.37/-0.34 0.36/-0.39 0.37/-0.45 0.38/-0.54 0.38/-0.59
-
23
Supplementary Figure 16. Change in unit cell parameters from the outside to the inside of the loop on crystal 1.
Supplementary Figure 17. Change in unit cell parameters from the outside to the inside of the loop on crystal 2.
-
24
Supplementary Figure 18. Mechanical deformation of crystal 1 (as a percentage change in cell parameters compared to unbent crystal 0) along the transect from the outside of loop to inside of loop. The zero position is defined as the interval on crystal 1 that most closely matches the unbent crystal.
Supplementary Figure 19. Mechanical deformation of crystal 2 (as a percentage change in cell parameters compared to unbent crystal 0) along the transect from the outside of loop to inside of loop. The zero position is defined as the interval on crystal 1 that most closely matches the unbent crystal.
-
25
Supplementary Figure 20. Mechanical deformation of crystal 1 (as a percentage change in metric dimensions of the crystal compared to unbent crystal 0) along the transect from the outside of loop to inside of loop.
Supplementary Figure 21. Mechanical deformation of crystal 2 (as a percentage change in metric dimensions of the crystal compared to unbent crystal 0) along the transect from the outside of loop to inside of loop.
-
26
Supplementary Figure 22. a) Angle between the plane of the [Cu(acac)2] molecules and the (010) plane and b) distance between the centroids of two chelate rings of adjacent molecules.
Supplementary Figure 23. Changes in the angle (a) and distance (b) as defined in Supplementary Figure 22 for
crystal 1.
Supplementary Figure 24. Changes in the angle (a) and distance (b) as defined in Supplementary Figure 22 for
crystal 2.
-
27
To demonstrate the maintenance of crystallinity of after bending and release an additional crystal was superglued to a
glass fibre and mounted on an Oxford Gemini Ultra diffractometer employing graphite monochromated Mo-Kα
radiation generated from a sealed tube (0.71073 Å) at 298 (2) K [8]. 45 diffraction images were collected the peaks
indexed and unit cell refined using CrysAlisPro [8]. The crystal was then bent in situ by approximately 20 ° from
linear by the application of pressure via a probe to the non-glued end of the crystal. After releasing the strain the same
45 diffraction images were recorded and processed. The crystal was then again bent, this time to 60 ° from linear and
the strain released. The same 45 diffraction images were recorded and processed. In each case the diffraction spots
appeared sharp with no change from the previous experiment. The crystal was then bent in situ until breaking (~ 90 °
from linear) and another 45 diffraction images were recorded and processed. The refined unit cell parameters and
average mosaicity are summarised in Supplementary Table 7.
Supplementary Table 7. Refined unit cell parameters and Mosaicity for one crystal after repeated bending and release.
Degree of bend
a (Å) b (Å) c (Å) β (°) Vol (ų) Av. Mosaicity
No. Reflections
Unbent 10.332(14) 4.703(9) 11.355(14) 91.75(12) 551(1) 1.27 129 After
bending to 20°
10.310(19) 4.706(6) 11.362(15) 91.89(13) 551(1) 1.26 142
After bending to 60°
10.320(15)
4.715(8) 11.336(14) 91.79(11) 551(1) 1.26 141
After the
crystal was
broken
10.347(12) 4.709(5) 11.374(8) 91.86(7) 553.9(9) 1.53 76
-
28
7. Other Flexible Crystals
Supplementary Figure 25. A single crystal of bis(3-bromo-2,4-pentanedione)copper(II) ([Cu(Bracac)2]) being bent. When the stress is released the crystal returns to its original morphology.
Supplementary Figure 26. A single crystal of bis(3-chloro-2,4-pentanedione)copper(II) ([Cu(Clacac)2]) being bent with a pin. One end of the crystal is held in place with superglue.
-
29
Supplementary Figure 27. A single crystal of bis(benzoylacetonato)copper(II) ([Cu(bzac)2]) being bent and then re-straightening upon the application and release of mechanical stress.
Supplementary Figure 28. A single crystal of bis(2,4-pentanedione)palladium(II) ([Pd(acac)2]) being bent and then re-straightening upon the application and release of mechanical stress.
-
30
Supplementary Figure 29. A single crystal of bis(3-chloro-2,4-pentanedione)palladium(II) ([Pd(Clacac)2]) being bent and then re-straightening upon the application and release of mechanical stress.
-
31
8. References
1. Holtzclaw, H. F. & Collman J. P. Polarographic Reduction of the Copper Derivatives of Several 1,3-Diketones in Various Solvents. J. Am. Chem. Soc. 74, 3776-3778 (1952).
2. TI 950 TriboIndenter User Manual. Revision 9.2.1211 (2011) Hysitron Incorporated, Minneapolis, MN. P202.
3. McPhillips, T. M., McPhillips, S. E., Chiu, H. J., Cohen, A. E., Deacon, A. M., Ellis, P. J., Garman, E., Gonzalez, A., Sauter, N. K., Phizackerley, R. P., Soltis, S. M., Kuhn, P. (2002) J. Synchrotron Rad. 9, 401-406.
4. Kabsch, W. Acta Cryst. D66, 125-132 (2010)
5. Dolomanov, O.V., Bourhis, L.J., Gildea, R.J, Howard, J.A.K. & Puschmann, H. (2009), J. Appl. Cryst. 42, 339-341.
6. Sheldrick, G.M. (2015). Acta Cryst. A71, 3-8.
7. Sheldrick, G.M. (2015). Acta Cryst. C71, 3-8.
8. CrysAlisPro (Rigaku Oxford Diffraction Ltd, Yarton, Oxfordshire, UK, 2009-2017)
top related