hf receiver principles noise and dynamic range jamie hall wb4ydl reelfoot amateur radio club april...

HF Receiver PrinciplesNoise and Dynamic Range

Jamie Hall WB4YDL

Reelfoot Amateur Radio Club

April 26, 2012

Receiver Sensitivity Limitations

Define Ant Noise FactorNoise Temp

F(x) of graphFrequencyAnt Noise FactorNoise Temp.

OverviewLinear except Daytime atmosphere

Understanding Logarithms• A logarithm is simply an exponent.• Example: given a base of 2 and an exponent of 3 we have 2³ = 8.

• Inversely: given a base of 2 and power 8, (2ⁿ = 8), then what is the exponent that will produce 8 ?

• That exponent is called the logarithm.

• We say the exponent 3 is the logarithm of 8 with base 2.

• 3 is the exponent to which 2 must be raised to produce 8.

Understanding Logarithms (con’t)• Common logarithms use base 10 and are used in fields such as engineering, physics, chemistry, and economics.

• Since 10³ = 1000, then log 1000 = 3.

• 3 is the exponent to which 10 must be raised to produce 1000.

• Using logarithms greatly simplifies talking about differences in very large and very small numbers.

• Important logarithm rule: log (x/y) = log x – log y

How to find logarithmsCalculator – use base 10, not ln

(natural)Table of logarithmsSlide rule. What’s that?Basics of determining the

Characteristic and mantissa

Using Decibels in Ham Radio

Using dB allows us to talk about very large differences in power or voltage levels with numbers that are easy to comprehend.

Example: The maximum power output of a transmitter in the USA is 1500 watts and the noise floor of a modern receiver is 0.04 microvolts.

The received power at this voltage level into 50 ohms (E²/R) is 0.000000000000000032 watts or 3.2 x 10-17. This is not easy to deal with !

We refer to power levels as dB above or below 1 miliwatt in a 50 ohm system and call the result dBm. Thus 1 milliwatt is 0 dBm.

1500 watts in dBm = 10 log (1500 / .001) = +62 dBm

3 x 10-17 watts in dBm = 10 log (3 x 10-17 / .001) = -135 dBm

This is much easier to comprehend and deal with.

Question: How many dBm does a 100 watt transmitter produce ?

Dynamic Range In general, DR is the ratio (or difference in dB) between the

weakest signal a system can handle and the strongest signal that same system can handle simultaneously.

Example: The normal human ear can detect a 1 kHz sound wave at a level of 10-12 watts/m² while the upper limit is about 1 watt/m², where pain is felt. The dynamic range of our ears is thus about 120 dB.

Example: Our eyes can detect the light from a star in a dark sky when about 10 photons per second reach the retina, which is about 10-13 watts/m². The Sun with its 300 watts/m², does not damage our eyes unless we look straight into it.

The baseball outfielder who drops a fly ball certainly knows about the blocking effects of the Sun. He employs an attenuator (sunglasses) to reduce the interference, but this may in fact put the desired signal (the baseball) below his noise floor. In radio, the attenuator would be a front-end AGC.

Blocking Dynamic Range

BDR is the difference in dB between minimum discernible signal (MDS) and an off-channel signal that causes 1 dB of compression in the receiver.

Sensitivity and Blocking• Blocking happens when a large off channel signal

causes the front-end RF amplifier to be driven to its compression point.

• As a result all other signals are lost (blocked).

• This condition is frequently called de-sensing—the sensitivity of the receiver is reduced.

• Blocking is generally specified as the level of the unwanted signal at a given offset.

• Original testing used a wide offset—typically 20 kHz. More recently, recognizing our crowded band conditions and the narrow spacing of CW and other digital modes, most testing today is done with close spacing of 2 kHz.

Wide & Close Dynamic Range

First IF Filter at 70.455 MHz

IMD 20 kHz Away

15 kHz Wide

First IF Filter at 70.455 MHz

IMD 2 kHz Away

15 kHz Wide

20 kHz Spacing 2 kHz Spacing

Nonlinearity and Intermodulation Distortion

• Nonlinearity in RF and IF circuits leads to two undesirable outcomes: harmonics and intermodulation distortion.

• Harmonics in and of themselves are not particularly troublesome.

• For example, if we are listening to a QSO on 7.230 MHz, the second harmonic, 14.460 MHz is well outside the RF passband.

• However, when the harmonics mix with each other and other signals in the circuit, undesirable and troublesome intermodulation products can occur.

Intermodulation Distortion (IMD)

RCV INPUT FILTER

Intermodulation Distortion Products: An Example

(1) Fifth-Order 3f1-2f2 7.218

(2) Third-Order 2f1-f2 7.221

(3) Signal One f1 7.224

(4) Signal Two f2 7.227

(5) Third-Order 2f2-f1 7.230

(6) Fifth-Order 3f2-2f1 7.233

Intermodulation Distortion Products: An Example

(1) Fifth-Order 3f1-2f2 7.218

(2) Third-Order 2f1-f2 7.221

(3) Signal One f1 7.224

(4) Signal Two f2 7.227

(5) Third-Order 2f2-f1 7.230

(6) Fifth-Order 3f2-2f1 7.233

Intermodulation Distortion Products: An Example

(1) Fifth-Order 3f1-2f2 7.218

(2) Third-Order 2f1-f2 7.221

(3) Signal One f1 7.224

(4) Signal Two f2 7.227

(5) Third-Order 2f2-f1 7.230

(6) Fifth-Order 3f2-2f1 7.233

Intermodulation Distortion Products: An Example

0

20

40

60

80

100

120

7.216 7.218 7.220 7.222 7.224 7.226 7.228 7.230 7.232 7.234

mHz

dB

3f1- 2f2

2f1- f2

f1 f2

2f2- f1

3f2- 2f1

Example: Transmitted IMD

Third Order Intermodulation Products

• The 3rd order products will be the largest (loudest) of the intermodulation products.

• As a general rule, the 3rd order products will increase (grow) 3-times faster than the fundamental signal (the signal of interest).

ARRL Receiver Test:Measured Response of the Signal of Interest

ARRL Receiver Test:Extrapolated Linear Region of the Measured Response of the Signal of Interest

ARRL Receiver Test:Measured Response of the IMD Product

ARRL Receiver Test:Extrapolated Linear Region of theMeasured Response of the IMD Product

The 3rd order intercept point (IP3): A Measure of Merit

Our graph illustrates that the

3rd order intercept point isdefined by the intersection

oftwo hypothetical lines.

Eachline is an extension of a

lineargain figure: first of the

signalof interest; and second, ofthe 3rd order

intermodulationdistortion product—from

whichIP3 gets its name.

You will note that the larger the value of IP3, the less likely the receiver will be adversely affected by 3rd order intermodulation products.

ARRL Receiver Test:Extrapolated Linear Region of theMeasured Response of the IMD Product

IMD Dynamic Range

SummaryRx sensitivity limitationsAntenna noise factor, frequency,

noise tempLogs & decibels to manage

referencesDynamic range, BDR, Sensitivity

& blockingIMD, 3rd order IMDExamples of receiver tests :

Sensitivity [(S+N)/N] and MDS measurement and S-meter calibration