heat cost allocator monitor 2.0/monitor 2.0 e domestic water … · 2016-11-03 · therefore, use...
Post on 23-Jul-2020
10 Views
Preview:
TRANSCRIPT
Heat cost allocator MONITOR 2.0/MONITOR 2.0 E Domestic water consumption data acquisition deviceMONITOR 2.0 PULSE
7200 series
OPERATING STEPS - INSTALLATION MANUAL
© Copyright 2014 Calef f i
Function
MONITOR 2.0 and MONITOR 2.0 E are latest-generation electronicheat cost allocators to be fitted on each radiator to meter heatconsumption in buildings with centralised systems featuring verticalheating distribution (riser type).When combined with a thermostatic or chrono-thermostatic valve,both temperature regulation and metering of heat consumption areperformed, obtaining improved comfort, quantification of the actualheat consumption and a fair allocation of costs. The heat consumption data can be collected via radio andprocessed directly by the building administrator/manager.
MONITOR 2.0 PULSE is a pulse acquisition device that, combinedwith a domestic hot and/or cold water meter with pulse output,enables measuring domestic water consumption for cost accountingfor each dwelling.Consumption data can be collected via radio and processed directlyby the building administrator/manager via the same software usedfor reading heat cost allocators MONITOR 2.0/2.0 E
78204.01 EN
www.caleffi.com
0470
CAUTION! CONSULT THIS MANUAL BEFORE USING THE PRODUCT
2
Identify:• No. of heat emitters• Type of valves/lockshield valves• Type of heat cost allocator mounting kit • Number of domestic water volume meters
1. PRELIMINARY INSPECTION (to be carried out by the installer)
OPERATING STEPSHEAT COST ALLOCATORS and PULSE ACQUIRERS - MONITOR 2.0 - 2.0 E - 2.0 PULSE
Example:• 200 cast iron plate radiators• 32 towel radiators• 40 DHW volume meters• 40 DCW volume meters
a) For the 200 cast iron plate radiators you need:- 180 Convertible radiator valves for iron pipe with 1/2”
angled connection- 180 Lockshield valves for iron pipe with 1/2”
angled connection- 20 Convertible radiator valves for iron pipe with 3/8”
straight connection- 20 Lockshield valves for iron pipe with 3/8”
straight connection- 200 code 720060 Kit (Table 1 on pages 11-12)- 200 code 720020 MONITOR 2.0 heat cost allocator- 160 code 200000 Thermostatic control head for
radiator valves- 40 code 201000 Thermostatic control head for
radiator valves with remote probe
b) For the 32 towel warmers you need:- 32 Convertible radiator valves for copper pipe with
1/2” angled connection- 32 Lockshield valves for copper pipe with 1/2”
angled connection- 35* code 720050 Kit (Table 1 on pages 11-12)- 32 code 720020 MONITOR 2.0 heat cost allocator- 32 code 200000 Thermostatic control head for
radiator valves
* Code 720050 comes in a minimum 5-piece pack and the ordertherefore needs to be a multiple of 5.
c) For hot and cold domestic water volume meters you need:- 40 code 794204/C 1/2” DHW meters with pulse output- 40 code 794204 1/2” DCW meters with pulse output- 80 code 720030 domestic water consumption data
acqusition device MONITOR 2.0 PULSE
Forward the purchase order as shown in the example below
pag. 3
page 4-5-6-7-8
page 15
page 16
page 17
page 17
pag.17-18-19
2. INSTALLATION AND MAPPING (to be carried out by the installer)
Valve / lockshield valve / thermostatic controlhead mounting
Heat cost allocator mounting according topositioning and clamping rules
Condominium Data Sheet compilation
Apartment Survey Sheet compilation
3. COMMISSIONING– PARAMETERISATION(to be carried out by the installer)
In situ heat cost allocator parameterisation
Radio transmission functional test
• Availability of a laptop PC with Microsoft®Windows operating system
• Purchase of a USB/radio device + SW7200software (code 720090) for reading, displayingconsumption and creating reports
4. HEAT COST ALLOCATOR CONSUMPTIONREADOUT PROCEDURES
(to be carried out by the condominium person in charge)
3
During the inspection it is essential to establish which mounting kit is suitable for the type of heating body on which the heat cost allocator is tobe fitted.See Table 1 on pages 11-12 to choose the suitable kit.
Example:
- Heat emitter: CAST IRON PLATES- Distance between the elements: LESS THAN 4 mm
- Mounting kit: code 720060
D D
D
Cast iron plates
720060*
720061*
4 4
L
Distance between elements (D) less than or equal to 4 mm
Distance between elements (D) from 4 to 10 mm
plate (39 mm) + anchor (20 / 39 mm)plate (39 mm) + anchor (59 mm) + anchor (75 mm)plate (55 mm) + anchor (20 / 39 mm) + anchor (59 mm)plate (55 mm) + anchor (75 mm)plate (88 mm) + anchor (39 mm) plate (88 mm) + anchor (59 mm) + anchor (75 mm)plate (88 mm) + anchor (75 mm) + screws (M4 x 130 mm)plate (39 mm) + self-tapping screwplate (39 mm) + threaded plateplate (39 mm) + welded stud boltsplate (39 mm) + expanding corner pieces
Code Description
7200 Mounting kit
720050720051720052720053720054720055720056720060720061720062720063
N.B. When ordering the mounting kit, check that the number of pieces is a multiple of the minimum pack.
IMPORTANT: The tightening torque of the screws used in the mounting kit must be between 0.8 and 1 N·m.
1. PRELIMINARY INSPECTION (to be carried out by the installer)
No. of items in the pack55555115551
4
2. INSTALLATION AND MAPPING (to be carried out by the installer)
Characteristic components
1 Tamper-proof seal2 Acquisition device complete with PCB3 Protection for tamper-proof element (to be removed during
installation)4 Display selection key5 Wall mounting screws (tightening torque 0.8-1 N·m)6 Plastic plate for wall mounting7 Wall mounting wall anchors
MONITOR 2.0 PULSE - code 720030
3
4
56
7
2
1
1 Tamper-proof seal2 Heat cost allocator complete with PCB3 Radiator probe protection (to be removed during
installation)4 Display selection button5 Retaining screws (tightening torque 0.8-1 N·m)6 Aluminium thermal coupling plate7 Fastening brackets
1 Anti-tampering seal2 Heat cost allocator complete with PCB3 Protection for the tamper-proof sensor (to be removed
during installation)4 Display selection button5 Wall fastening screws (tightening torque 0.8-1 N·m)6 Aluminium plate + spacers7 Wall fastening anchors8 Metal clamp for fastening the extended probe to the
radiator/convector 9 Copper stud bolts + nuts for welded fastening10 Remote probe11 Remote probe cover12 Tamper-proof label
3
4
5
6
7 2
1
MONITOR 2.0 - code 720020
3
4
5
6
7
89
10
11
12
2
1
MONITOR 2.0 E (remote probe) - code 720025
2.0 E 2.0 PULSE
5
Installation of the heat cost allocator/pulse acquirer
Installing the tamper-proof seal
When installation is complete, fit the tamper-proof seal compressing the two tabs and continue as illustrated below:
① ②
STEP 1Before proceeding with installation, removethe probe protection (a) and the tamper-proof seal (b). - Depending on the device that has to beinstalled, fasten the wires according to thefollowing pictures:
STEP 2Install the heat cost allocator/pulse acquirerhooking it onto the top part of the anchoringsupport and pushing downward.
STEP 3Press down on the bottom part of the heatcost allocator until it is securely in place.
ab
a
b
MONITOR 2.0
MONITOR 2.0 E - 2.0 PULSE
MONITOR 2.0 - 2.0 E - 2.0 PULSE
ab
2. INSTALLATION AND MAPPING (to be carried out by the installer)
STEP 1Before proceeding with installation, removethe probe protection (a) and the tamper-proof seal (b).
STEP 2Install the heat cost allocator on the heatemitter hooking it onto the top part of thealuminium anchoring plate and pushingdownward.
STEP 3Press down on the bottom part of the heatcost allocator until it is securely in place.
Push only the two side parts ofthe seal into the heat costallocator until it fits into place.
Finally, push in the centralpin of the seal until it fits intoplace.
6
L < 3000 mm
h
L > 3000 mm
h
valvola
Width up to 3000 mm
50% of the width (W)*
75% of the height (H) ±1 cm25% of the width (W)
Width over 3000 mm
(2 heat cost allocators need to be installed)
Position the heat cost allocator against the riser on which thethermostatic valve is fitted (flow).
* If there is an odd number of radiator elements, the installationposition is the median of the width, between two elements, closestto the valve. 75%
of the height (H) (±1cm)
In case of the welded mounting kit:- Strip the paint off the radiator at the points where the stud bolts areto be welded on.- Weld the stud bolts in the gap between two ridges. If there is anodd number of ridges, choose the median position closest to thevalve.
- Cut off the excess part using cutting nippers, as it may damage thedevice.
YES NO
The heat cost allocatorpositioning indicator mustALWAYS be positionedexactly at 75% (±1 cm) of theheight of the heat emitter.
During installation, makesure that the arrow ALWAYSfaces up.
75% of the height (H) ±1 cm
2. INSTALLATION AND MAPPING (to be carried out by the installer)MONITOR 2.0
If you make a mistake, do not remove the stud bolts already weldedon, as you risk damaging the radiator; cut them at the base as muchas possible.
valve
Heat cost allocator position on radiator Heat cost allocator position on towel radiator
N.B. When installation is complete, the heat cost allocator is automatically activated after about 90 second.The following appears on the display:
You can now proceed with parameterisation of the heat cost allocator (see page 17).
Welded mounting kit
25% of the width (W)
7
In order to ensure measurement according to the regulations, the heat costallocator must be positioned at a distance not less than 10 cm from theheating body and at a height equal to half the height of the heating body.
10 cm
10 cm
50% H 50% H
H H
50% H 10 cm
H
50% H
10 cm
H
The sensor must be positioned at 75% (±1 cm) of the coildevelopment (25% from the inlet, 75% from the outlet).
75% (±1 cm)
The remote sensor is to be fitted on the return chamber at 50% of theheight.
N.B. The remote probe must be installed in such a way that anyattempt to disconnect the probe will leave a trace. Therefore, use the tamper-proof label provided on the outer probecover.
75% (±1 cm)
75% (±1 cm)
75% (±1 cm)
During installation, make sure that the centre-line of the part shownin Figure 1 is positioned exactly at 75% (±1 cm) of the developmentof the coil or at 50% (±1 cm) of the height in the case of a single-block convector.
2. INSTALLATION AND MAPPING (to be carried out by the installer)MONITOR 2.0 E (with remote probe)
Determination of the extended probe sensor positionSingle-fin or coil convector
FASTENING WITH SCREWS OR CLAMPS WELD FASTENING
Determination of the remote probe sensor positionSingle-block convector
Heat cost allocator position with convector
10 cm
10 cm
50% H 50% H
H H
50% H 10 cm
H
50% H
10 cm
H
N.B. When installation is complete, the heat cost allocator is automatically activated after about 90 seconds.The following appears on the display:
You can now proceed with parameterisation of the heat cost allocator (see page 17).
①
N.B. If using a remote probe with a radiator, the centre-line of theprobe positioning indicator must be positioned (instead of the thermalcoupling plate) according to the instructions given on page 6.
copper pinpositioningpoints
50% H(±1 cm)
8
2. INSTALLATION AND MAPPING (to be carried out by the installer)MONITOR 2.0 PULSE (pulse acquirer)
Firstly use the special wall mounting hooks provided, install the rearplastic plate and, finally, use the fixing screws, as shown in thefollowing picture:
The generic pulse must be potential free(volt free contact, maximum frequency 50 Hz.)
IN
GND
Fig. A
Pulse outputwire from thevolume meter
Connect the pulse output wire from the volume meter to the deviceinputs with screw terminals (Figure A) as illustrated in the picturebelow:
Positioning the consumption data acquisition device
In order to guarantee correct operation of the consumption dataacquisition device, it is necessary not to position the device in directcontact with pipes nor under them, in order to avoid malfunctions dueto drops of condesation and humidity.
N.B. When installation is complete, the heat cost allocator is automatically activated after about 90 seconds.The following appears on the display:
You can now proceed with parameterisation of the heat cost allocator (see page 17).
9
2. INSTALLATION AND MAPPING (to be carried out by the installer)MONITOR 2.0 - 2.0 E (remote probe)
800 600 120 10 F
Room Heat cost allocator serial numberMONITOR 2.0 - 2.0 E
Radiator cover
S = shelf (distance < 15 cm)C = full cover
Dimensions
S C
C
C
C
C
C
KITCHEN
LIVING ROOM
MASTER BEDROOM
BATHROOM
HALL
(*) H (mm) W (mm) D (mm)
2.0 E
2.0 E
2.0 E
2.0 E
2.0 E
2.0 ECHILDREN’S BEDROOM
(*) H means the height of the radiator andNOT the distance between hub centres
No. ofelements
Type UNI 10200 See Table 2 Example: A
Installedcapacity (W) ΔT 60°C
Tick if the heat cost allocator is with remote
probe (MONITOR 2.0 E)Brand Series Model
TypeEN 442
S
S
S
S
S
2 1 3 4 5 6 7 8 x
C 2.0 ES
(2) If you do not have the brand-name, series and model of the towel warmer or radiator, you need to send an e-mail to the address 7200.monitor@caleffi.com attaching a photo and indicating the tube and manifolds diameters and to which condominium, dwelling androom they correspond.
RADIATOR / CONVECTOR / (1)
(1) If convectors are present it is necessary to fill the “Installed capacity (W) field. ΔT 60°C” TOWEL RADIATORS (2)
Example of data entry for a radiator using UNI 10200:
1 2 3 6 7 84 5
UNI 10200 type (see Table 2):
EXAMPLE: Heating body: cast iron plates, smooth columns
Material Type Description UNI 10200 type
Small columnsSection < 30 x 30 mm
Large columnsSection > 30 x 30 mm
hub* 50 mm
hub* 55 mm
hub* 55 mm
hub* 60 mm
A
B
CD
Columns joined by diaphragm E
Smooth columns F
Finned columns
Highly finned
Averagely finned
Lightly finned
Plate without fins
With rear fins
With fins between the plates
Vertical or horizontal tubes
G
H
I
L
M
N
O
P
Cast iron or steel
Bare tube**
Cast iron plates
Aluminium
Steel
Cast iron or steel
Hub means the following dimension:* Bare tube means tubing visible in the rooms.**
D + 23 D + 23
D
RoomEnter the room where the heating body is installed.
Heat cost allocator serialnumberEnter the serial numberindicated on the label onthe top part of the heatcost allocator.
Radiator coverIndicate whether the radiator has a shelf cover Sonly if its distance from the radiator is less than 15 cm or a full cover C(tick ONLY if the radiator has a shelf or a full cover).
DimensionsSpecify thedimensions of theheat emitterexpressed in mm.
H = heightW = widthD = depth
No. of elementsEnter the number of elements the radiator is made of.
Convector. Installed capacity (W)Where there are convectors, it is essential to indicate the installed capacity referring to DT 60°C.
MONITOR 2.0 E heat cost allocator with remote probeTick ONLY if the heat cost allocator is fitted with a remote probe (MONITOR 2.0 E).
H
W D
1
2
3
4
5
6
7
8
MappingMapping means filling the condominium and apartment survey sheets (see pages 15-16)
10
2. INSTALLATION AND MAPPING (to be carried out by the installer)MONITOR 2.0 - 2.0 E (remote probe)
2. INSTALLATION AND MAPPING (to be carried out by the installer)MONITOR 2.0 PULSE (pulse acquirer)
DimensionsSpecify the dimensions of the heat emitter expressed in mm.
Brand, series and modelSpecify, if possible, brand, series and model of thetowel warmer.
Installed capacity (W)Specify, if possible, the installed thermal capacity referring toDT 60°C.
MONITOR 2.0 E heat cost allocator with remote probeTick ONLY if the heat cost allocator is fitted with a remote probe(MONITOR 2.0 E).
Stair, floor and roomSpecify the stair, floor and room where theMONITOR 2.0 PULSE is installed.
Serial number of theacquirerMONITOR 2.0 PULSEEnter the serial numberindicated on the label onthe top part of the heatcost allocator.
DHW or DCWSpecify whether the deviceis connected to a hot orcold water volume meter
Other type of meterIn case the MONITOR 2.0 PULSE is not connected to a volumemeter, specify the type (e.g.: heat meter).
K (litres/pulse or kWh/pulse)Specify the K value (litres/pulse) that characterize the volumemeter or the K value (kWh/pulse) in case of a heat meter.
Diameter of the volume meterSpecify the diameter of the volume meter or the diameter ofheat meter
Initial value to be setSpecify the initial value to be set into the pulse acquirer,expressed in m3 for a volume meter (in kWh for a heat meter)displayed on the meter at the moment of the installation of theMONITOR 2.0 PULSE acquirer.ATTENTION : the initial value is MANDATORY for theparameterization!
Serial number of the volume meterSpecify the serial number of the volume meter or the one of theheat meter connected to the pulse acquirer.
854BRAND 1 SERIES 1 MODEL 11800 600 30 1
Room Heat cost allocator serial numberMONITOR 2.0 - 2.0 E
Radiator cover
S = shelf (distance < 15 cm)C = full cover
S C
C
C
C
C
C
KITCHEN
LIVING ROOM
MASTER BEDROOM
BATHROOM
HALL
(*) H (mm) W (mm) D (mm)
2.0 E
2.0 E
2.0 E
2.0 E
2.0 E
2.0 ECHILDREN’S BEDROOM
Type UNI 10200 See TAB. 2 Example: A
Installed capacity (W) ΔT 60°CBrand Series Model
TypeEN 442
S
S
S
S
S
2 1 3 4 5 6 7 8
C 2.0 ES
(2) If you do not have the brand-name, series and model of the towel warmer or radiator, you need to send an e-mail to the address 7200.monitor@caleffi.com attaching a photo and indicating the tube and manifolds diameters and to which condominium, dwelling androom they correspond.
RADIATOR / CONVECTOR / (1)
(1) If convectors are present it is necessary to fill the “Installed capacity (W) field. ΔT 60°C” TOWEL RADIATORS (2)
Dimensions (*) H means the height of the radiator andNOT the distance between hub centres
No. ofelements
Tick if the heat cost allocator is with remote
probe (MONITOR 2.0 E)
TIMBRO E FIRMA
A 1 KITCHEN 1 2 3 4 5 6 7 8 X 10 3/4” 15,203 0123456789
DOMESTIC HOT / COLD WATER VOLUME METER
Stair Floor RoomSerial number of the acquirer
MONITOR 2.0 PULSEDomestic hot or
cold water
DHW DCW
Other type of meterK
(litres/pulse or kWh/pulse)
Initial value to be set
(m3 or kWh)Serial number of the
volume meter
DHW DCW
DHW DCW
DHW DCW
Diameter of thevolume meter
Example of data entry for a volume meter :
Example of data entry for a radiator using EN442:
3
6
5
1 2 3 64
1 2 3
6
7
8
9
4
5
10
1 2 3 6 8 94 5 10
5 7
RoomEnter the room where the heat emitter is installed.
Heat cost allocator serialnumberEnter the serial numberindicated on the label onthe top part of the heatcost allocator.
No. of elementsEnter the number of elements the radiator is made of. Incase of towel warmers specify “1”.
8
1
2
Radiator coverIndicate whether the radiator has a shelf cover Sonly if its distance from the radiator is less than 15 cmor a full cover C(tick ONLY if the radiator has a shelf or a full cover).
4
8
7
7
11
TABLE 1 - Mounting kit MONITOR 2.0
2. INSTALLATION AND MAPPING (to be carried out by the installer)
D D
D D
Element radiators MOUNTING KIT
Cast iron columns
Distance between elements (D) less than or equal to
30 mm
Distance between elements (D)
greater than 30 mm
Steel tubular
Tubolare acciaio a colonne
Passodegli elementida 45/46 mm
Aluminium columns
Ribbed steel
720050*
720052*
720060*
720061*
720060*
720061*
D
Distance between elements (D)
less than or equal to 35 mm
Distance between elements (D)
from 36 to 45 mm
720051*
720053*
* Minimum 5-piece pack
4 4
Distance between elements (D)
less than or equal to 4 mm
Distance between elements (D)
from 4 to 10 mm
720052*
720054*
Distance between element centres (C)
less than 50 mm and distance (D) less than 30 mm
Distance between element centres (C)
greater than or equal to 50 mm and distance (D)
less than 30 mm
D D 30
Cast iron plates
Distancebetween elements (D) less than or equal to
4 mm
Distancebetween elements (D)
from 4 to 10 mm
35 35 D 45 D
12
Pas
so
* Minimum 5-piece pack
Panel radiators
Ridged surface Vertical profile
Smooth surface
Vertical
Horizontal
Flat tubes
720062*
Smooth surface
Lamellar radiators
LamellarLamellar
720063
Towel warmer
Horizontal tubes 720050*
Distance between elements (D)
from 24 to 28 mm
D
24 D 28
Towel radiator
MOUNTING KIT
MOUNTING KIT
MOUNTING KIT
TABLE 1 - Mounting kit MONITOR 2.0
2. INSTALLATION AND MAPPING (to be carried out by the installer)
13
TABLE 1 - Mounting kit MONITOR 2.0 E
Thermal convectors
Single-fin convector Single element without coil
Double or triple element without coil
Single, double or triple element with coil
Coil convector
Single-fin convector
Single-block convector
(mounting kit included in the heat cost allocator pack)
Weld-fasteningsingle-block convector
2. INSTALLATION AND MAPPING (to be carried out by the installer)
14
Material Type Description UNI 10200 type
Small columnsSection < 30 x 30 mm
Large columnsSection > 30 x 30 mm
hub* 50 mm
hub* 55 mm
hub* 55 mm
hub* 60 mm
A
B
CD
Columns joined by diaphragm E
Smooth columns F
Finned columns
Highly finned
Averagely finned
Lightly finned
Plate without fins
With rear fins
With fins between the plates
Vertical or horizontal tubes
G
H
I
L
M
N
O
P
Cast iron or steel
Bare tube**
Cast iron plates
Aluminium
Steel
Cast iron or steel
Hub means the following dimension:* Bare tube means tubing visible in the rooms.**
D + 23 D + 23
D
TABLE 2 - UNI 10200
2. INSTALLATION AND MAPPING (to be carried out by the installer)
15
Condominium Data SheetC
ON
DO
MIN
IUM
DA
TA
SH
EE
T
Fax
Co
nd
om
iniu
m n
ame
* In
dic
ate
the
gra
nd
to
tal o
f A
LL
th
e A
PA
RT
ME
NT
SU
RV
EY
SH
EE
TS
of
the
con
do
min
ium
Str
eet
Nu
mb
er
Tax
co
de
nu
mb
er
Po
stal
co
de
Cit
yP
rovi
nce
STA
MP
AN
D S
IGN
ATU
RE
BUILDING ADMINISTRATOR/
MANAGER
Den
om
inat
ion
No
. of
build
ings
*No
. of
dwel
lings
*N
o. o
f ra
diat
ors*
No
. of
tow
el w
arm
ers/
radi
ato
rs*
No
. of
conv
ecto
rs*
No
. of
MO
NIT
OR
2.0
he
at c
ost
allo
cato
rs*
No
. of
MO
NIT
OR
2.0
E
heat
co
st a
lloca
tors
*
Add
ress
Nam
e an
d su
rnam
e
Pho
ne/m
obil
e no
.F
ax
E-m
ail
Den
om
inat
ion
Add
ress
Nam
e an
d su
rnam
e
Pho
ne/m
obil
e no
.
E-m
ail
TECHNICIAN (who did the survey)
No.
dom
estic
hot w
ater
volu
me
met
er
No.
of
MO
NIT
OR
2.0
PU
LSE
pu
lse
acqu
isiti
on d
evic
e*
No.
dom
estic
cold
wat
ervo
lum
e m
eter
16
Apartment Survey Sheet
SC C C C C C C C
KIT
CH
EN
LIV
ING
RO
OM
MA
STE
R B
ED
RO
OM
BA
THR
OO
M
HA
LL
(*)
H (m
m)
W (m
m)
D (m
m)
2.0
E
2.0
E
2.0
E
2.0
E
2.0
E
2.0
E
2.0
E
2.0
E
ST
AM
P A
ND
SIG
NA
TU
RE
C C
2.0
E
2.0
E
CH
ILD
RE
N’S
BE
DR
OO
M
S S S S S S S S S
C2.
0 E
S
C2.
0 E
S
C2.
0 E
S
Con
dom
iniu
m n
ame
Stre
etC
ity
Sur
vey
dat
aS
tairc
ase
Floo
rIn
terio
rTe
chni
cian
who
did
the
surv
eyTe
chni
cian
’s p
hone
/mob
ile n
o.
Num
ber
Pro
vinc
e
AP
AR
TM
EN
T S
UR
VE
Y S
HE
ET
M
r/M
s P
ho
ne
/mo
bil
e n
o.
(2) I
f you
do
not h
ave
the
bran
d-na
me,
ser
ies
and
mod
el o
f the
tow
el w
arm
er o
r rad
iato
r, yo
u ne
ed to
sen
d an
e-m
ail t
o th
e ad
dres
s 72
00.m
onito
r@ca
leff
i.com
atta
chin
g a
phot
o an
d in
dica
ting
the
tube
and
man
ifold
s di
amet
ers
and
to w
hich
con
dom
iniu
m, d
wel
ling
and
room
they
cor
resp
ond.
RA
DIA
TO
R /
CO
NV
EC
TO
R
/(1
)
(1) I
f con
vect
ors
are
pre
sent
it is
nec
essa
ry to
fill
the
“Ins
talle
d c
apac
ity (W
)
field
. T
60°C
” T
OW
EL
RA
DIA
TO
RS
(2)
DO
ME
ST
IC H
OT
/ C
OL
D W
AT
ER
VO
LU
ME
ME
TE
R
Sta
irFl
oor
Roo
mS
eria
l num
ber
of t
he p
ulse
acq
uire
rM
ON
ITO
R 2
.0 P
ULS
ED
omes
tic h
ot o
rco
ld w
ater
D
HW
D
CW
Oth
er ty
pe
of m
eter
K (l
itres
/pul
seor
kW
h/p
ulse
)
Initi
al v
alue
to b
e se
t
(m
3 or
kW
h)S
eria
l num
ber
of t
hevo
lum
e m
eter
D
HW
D
CW
D
HW
D
CW
D
HW
D
CW
Dia
met
er o
f the
volu
me
met
er
Roo
mH
eat c
ost a
lloca
tor s
eria
l num
ber
MO
NIT
OR
2.0
- 2.
0 E
Rad
iato
r cov
er
S =
she
lf (d
ista
nce
< 1
5 cm
)C
= fu
ll co
ver
Dim
ensi
ons
(*) H
mea
ns th
e he
ight
of t
he ra
dia
tor a
ndN
OT
the
dis
tanc
e b
etw
een
hub
cen
tres
N
o. o
fel
emen
ts
Typ
e U
NI 1
0200
S
ee T
able
2
Exa
mp
le: A
Inst
alle
dca
pac
ity (W
)
T 6
0°C
Tick
if th
e he
at
cost
allo
cato
r is
with
rem
ote
pro
be
(MO
NIT
OR
2.0
E)
Bra
ndS
erie
sM
odel
Typ
eE
N 4
42
17
Parameterisation (to be carried out by the installer) comprises the following services:
• In situ heat cost allocator parameterisation.• Radio transmission functional test.
Parameterisation means programming the heat cost allocator with the power value (DT 60°C) according to the actual dimensions andcharacteristics of the heating body on which it is installed. Parameterisation, in case of domestic hot/cold water pulse acquirers, means programming the characteristic coefficient K (litres/pulse) of thevolume meter to which the device is connected. It is besides possible to match the count of the pulse acquirer with the one of the volume meter.This data is necessary for proper metering of the heat consumption by the heat cost allocators which are programmed by means of theUSB/radio device (code 720090) and the software provided. Normally, parameterisation is done in one go when installation has been completed and the mapping data of the specific building (see pages15 - 16) has been entered in the SW7200 software.
3. COMMISSIONING – PARAMETERISATION
4. HEAT COST ALLOCATOR CONSUMPTION READOUT PROCEDURESMONITOR 2.0 - 2.0 E - 2.0 PULSE
Consumption is read (by the condominium person in charge) using a laptop PC with Microsoft® Windows operating system, the USB/radiodevice (code 720090) and the SW7200 software provided, which allow reading, displaying consumption and creating reports.A user guide for proper use of the software is provided
5L · 0,
L
502
mbar
300350
400450
500550
600
04
0,5
11,
52
2,5
33,
54
502
mbar
300350
400450
500550
600
04 3 2 1 00,
51
1,5
22,
53
3,5
4
code 720020code 720025
Laptop PC
Code 720090
Consumption data readouts by means of the USB to radio device.
code 720030
18
4. READING THE DISPLAYMONITOR 2.0 - 2.0 E (remote probe)
Message Meaning Notes
- OFF The display is OFF.Low consumption mode is active.
8888.8.8 DISPLAY TESTUsed to visually check that all thedisplay segments are functioning.
FL8888FL8888
ALERTS(visible only incase of alerts)
Shows a warning or fault code.Fr8888 or FL8888
e i2345CURRENT
HEATING SEASONCONSUMPTION
Current heating seasonconsumption
F56789PREVIOUS
HEATING SEASONCONSUMPTION
Previous heating seasonconsumption
3 i.05PREVIOUS YEARCONSUMPTIONLOGGING DATE
Day/month when the previousperiod consumption was stored
OPERATINGSTATUS :operating
a_i234FIRST PART OFSERIAL NUMBER
First 4 digits of the heat costallocator serial number
_5678SECOND PART OFSERIAL NUMBER
Last 4 digits of the heat costallocator serial number
H_i5.09 RESET Reset date
li57.baFW VERSIONINSTALLED Shows the firmware version installed
OTHER MESSAGES DIFFERENT FROM THOSE LISTED ABOVE ARESTRICTLY FOR QUALIFIED TECHNICAL PERSONNEL
88:88:88
EXXXXX
FXXXXX
F L XXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAILUnIt
fd GG.MM
OpErat
a_8888
Press the selection button
EXXXXX
FXXXXX
FLXXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAIL
d GG:MM
A 20X X
L XXX
88:88:88
EXXXXX
FXXXXX
F L XXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAILUnIt
fd GG.MM
OpErat
a_8888
EXXXXX
FXXXXX
FLXXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAIL
d GG:MM
A 20X X
L XXX
88:88:88
EXXXXX
FXXXXX
F L XXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAILUnIt
fd GG.MM
OpErat
a_8888
EXXXXX
FXXXXX
FLXXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAIL
d GG:MM
A 20X X
L XXX
88:88:88
EXXXXX
FXXXXX
F L XXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAILUnIt
fd GG.MM
OpErat
a_8888
EXXXXX
FXXXXX
FLXXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAIL
d GG:MM
A 20X X
L XXX
88:88:88
EXXXXX
FXXXXX
F L XXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAILUnIt
fd GG.MM
OpErat
a_8888
19
Message Meaning Notes
- OFF The display is OFF.Low consumption mode is active.
DISPLAY TEST Used to visually check that all thedisplay segments are functioning.
OPERATINGSTATUS : operating
CURRENT PERIODCONSUMPTION
First 4 digits of the totalconsumption logged by the volumemeter connected to the device
CURRENT PERIODCONSUMPTION
Last 4 digits of the totalconsumption logged by the volumemeter connected to the device
CURRENT PERIODCONSUMPTIONDECIMALS
Decimals of the total consumptionlogged by the volume meterconnected to the device
ALERTS(visible only incase of alerts)
Shows a warning or fault code.Fr8888 or FL8888
PREVIOUSPERIOD
CONSUMPTIONFirst 4 digits of the total
consumption of the previous year
PREVIOUSPERIOD
CONSUMPTIONLast 4 digits of the total
consumption of the previous year
PREVIOUS YEARCONSUMPTIONLOGGING DATE
Day/month when the previous yearconsumption was stored
FIRST PART OFSERIAL NUMBER
First 4 digits of the heat costallocator serial number
SECOND PART OFSERIAL NUMBER
Last 4 digits of the heat costallocator serial number
FW VERSIONINSTALLED Shows the firmware version installed
Keep the
buttonpressed
for 5 sec.
4. READING THE DISPLAYMONITOR 2.0 PULSE (pulse acquirer)
Press the selection button
OTHER MESSAGES DIFFERENT FROM THOSE LISTED ABOVE ARESTRICTLY FOR QUALIFIED TECHNICAL PERSONNEL
EXXXXX
FXXXXX
FLXXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAIL
d GG:MM
A 20X X
L XXX
88:88:88
EXXXXX
FXXXXX
F L XXXX
SEnS-X
b GG:MM
U X.XX.XX
OPErAtFAILUnIt
fd GG.MM
OpErat
a_8888
20
Declaration of conformity
It is hereby declared that the product meets the applicable essential requirements of the R&TTE Directive 1999/5/EC. The CE 0470 marking on theproduct and in this document certifies conformity with the Directive. An unabridged copy of the Declaration of Conformity with the R&TTE Directive1999/5/EEC is available on request at the address below.
CALEFFI S.P.A.S.R. 229, n. 2528010 Fontaneto d’Agogna (NO) - ItalyTel. +39 0322 8491 / Fax +39 0322 863723Model: 7200Marking: CE 0470
We reserve the right to make improvements and modifications to the products described and the relative technical data at any time and without priornotice.
Problem Likely cause Suggested solution
Device disconnected from the radiator Impact or other Contact a certified installer to have it fastened
Missing seal Tampering Contact a certified installer to have it fitted
Position of the device changed since it wasinstalled Tampering, impact or other Contact a certified installer to have it fastened
The display shows the alert code FL8888 or Fr8888
The internal self-test has detected a faultContact a certified installer and specify the
code FL8888 or Fr8888
Null consumption is shown No consumption has been logged.This is not a fault. If the radiator is off, no energyemission is detected. In case the volume meter isreplaced the count of the device must be reset.
Low consumption is shown Beginning of a new season(heat cost allocator only)
This is not a fault. When the season start dateis exceeded shown heat consumption is reset
to zero
Nothing is shown on the display when thebutton is pressed Internal problem Contact a certified installer to have the device
checked
Warnings for proper disposal of the product
The symbol shown on the side appears on the product MONITOR 2.0/2.0 E/2.0 PULSE to indicate that this product may notbe disposed of as household waste.This means that the European Directive on waste electrical and electronic equipment (WEEE) applies and that the productmust therefore be sent to differentiated waste collection centres.
Moreover, the national laws on waste equipment collection systems need to be complied with.
TROUBLESHOOTING
top related