haz boom rebuilding · haz boom 32-33-36 m rebuilding of boom section original assembly...

HAZ BOOM 32-33-36 mREBUILDING OF BOOM SECTION

Original

Assembly Instructions for Upgrade Kit67215200-100, version 1.00GB - 05.2015

www.hardi-international.com

We congratulate you for choosing a HARDI plant protection product. The reliability and efficiency of this product depend upon your care. The first step is to carefully read and pay attention to this instruction book. It contains essential information for the efficient use and long life of this quality product.

Instruction Book FormalitiesThe original instruction book is approved and published in English. All other languages are translations of the original book. In the event of any conflicts, inaccuracies or deviations between the English book and other languages, the English version shall prevail.

Illustrations, technical information and data in this book are believed to be correct at the time of printing. As it is the policy of HARDI INTERNATIONAL A/S to continuously improve our products, we reserve the right to make changes in design, features, accessories, specifications and maintenance instructions at any time and without notice.

HARDI INTERNATIONAL A/S is without any obligation in relation to implements purchased before or after such changes.

HARDI INTERNATIONAL A/S cannot undertake any responsibility for possible omissions or inaccuracies in this publication, although everything possible has been done to make it complete and correct.

Published and printed by HARDI INTERNATIONAL A/S.

All rights reserved.

User EvaluationDear Reader,

We update our instruction books regularly. Your suggestions for improvement are appreciated and will help us to create ever more user-friendly instructions. Send us your suggestions to this e-mail address:

Thank you.

TechDoc@hardi-international.com

3

Table of Contents

InstructionsInitial Guidance .....................................................................................................................................5

General Info ............................................................................................................................................................................................................... 5Where on the Sprayer ......................................................................................................................................................................................... 5Tools and Materials Needed ............................................................................................................................................................................ 5

Existing Boom Parts ...............................................................................................................................6Removing Existing Parts .................................................................................................................................................................................... 6

New Boom Section .................................................................................................................................7Assembly Work ........................................................................................................................................................................................................ 7Spare Parts ............................................................................................................................................................................................................... 13

4

5

Instructions

Initial Guidance

General Info

The existing spray boom has a weak section, which may result in some parts breaking, when operating the spray boom.

Some of the components on the boom must be replaced to improve the strength of the boom.

Follow these instructions carefully step-by-step to complete the changes.

Where on the Sprayer

In the middle of right and left wings of the spray boom.

Tools and Materials Needed

• Wrench

• Socket wrench

• Rubber mallet

• Grease

• Lifting gear

Be aware that the weight for the existing boom section alone is approx. 40 - 45 kg, and a similar weight for the new boom section. Use lifting gear or get a helping hand to complete the assembly work in a safe way.

Instructions

6

Existing Boom Parts

Removing Existing Parts

Unfold the spray boom and support it.

Remove the existing boom section, which is to be replaced.

The boom should now look like this (only steel parts are shown in the picture):

Instructions

7

New Boom Section

Assembly Work

From the delivered upgrade kit, the new boom parts are assembled in the following order.

Place the red steel part on the floor.

Mount the two bolts M16 x 100.

Mount the nuts on the opposite side.

Grease bolt threads for easier screwing.

These bolts are later to be used for alignment of the boom section.

Mount the ram eye, Nord-Lock washers and nuts as shown.

Align the ram eye hole with the steel bracket holes.

Tip: Insert a round steel rod through all three holes to get the alignment.

Instructions

8

Lift up the steel part to align it with the adjacent boom section.

The ram eye is connected at the top of the boom.

Lifting straps should be placed as shown.

Instructions

9

Mount the black hinge pin at the bottom for connecting the boom sections.

If needed, use a rubber mallet to get the hinge pin placed correctly.

Mount a lock nut at the end of each hinge pin.

Instructions

10

The hinge pin at the bottom:

The top must be pointing in this direction when mounted.

Mount the grease nipples at the top of each hinge pin.

Mount the hinge pin at the top for connecting the ram eye.

Insert the bushing to ensure correct connection between ram eye and hinge pin.

Instructions

11

Adjust the M16 bolts and ram eye for aligning the boom sections.

Only make minor adjustments this way (only a few turns of the nuts for bolts or ram eye, if needed).

Bigger adjustments should be carried out using shim between this new boom section and the outer boom sections.

Assembly work is completed.

Instructions

12

Spare Parts

To see updated spare part information, visit the Agroparts website.

Here all parts information can be accessed in the spare parts catalogue:

1. Go to www.agroparts.com, register for free and log in.

2. Select “HARDI” in the menu on the left.

3. Select “Spare parts catalogue” and find your spare part.

4. Online ordering is also possible.

5. Contact your HARDI dealer for further information on spare parts.

HARDI INTERNATIONAL A/S

Helgeshøj Allé 38 - DK 2630 Taastrup - DENMARK