gasketsgaskets - kalasanat.comkalasanat.com/wp-content/uploads/2018/06/01-tombo-gasket.pdf · 2 in...
Post on 15-Aug-2019
212 Views
Preview:
TRANSCRIPT
GASKETSGASKETS
ContentsSafe Usage/Explanatory notes for customers ………………………………… 1
Definitions of Terminology …………………………………………………………………………… 2
Gasket Selection ……………………………………………………………………………………………… 3~5
■ High Temperature Use Sheet Gaskets ……………………………………………… 6
■ Joint Sheets ………………………………………………………………………………………………… 7~13
■ Vortex Gaskets ………………………………………………………………………………………… 12~29
■Metal Gaskets ………………………………………………………………………………………… 30~36
■Metal Jacketed Gaskets …………………………………………………………………… 37~39
■ GRASEALTM Gaskets ……………………………………………………………………………… 40~41
■ NAFLONTM Gaskets ……………………………………………………………………………… 42~53
■ Cloth Gaskets ………………………………………………………………………………………… 54~55
■ Rubber Gaskets ……………………………………………………………………………………… 56~57
■ Other Gaskets …………………………………………………………………………………………… 58~59
■ Gasket Paste ……………………………………………………………………………………………… 60~61
■ Standard Dimension Charts …………………………………………………………… 63~108
■Numerical Index …………………………………………………………………………………… 110~112
11
Properties/applications shown throughout this catalog are typical.Performance data referred to in this catalog are based on our own test results and on performance in generalapplications under normal conditions. Products listed in this catalog are used in diverse locations and for numerous types of machinery and equipment, andactual conditions of use also differ extensively. Consequently, when using these products, we recommend that youimplement verification tests under the actual conditions of use.Regarding individual applications, it is necessary to make a selection decision based on individual designs and onsuitability evaluations. For special applications, please consult us. The contents of this catalog are subject to change without prior notice.1. Never use for any purpose other than the prescribed application.2. When processing, use sharp cutting tools.3. Always follow the instructions in this catalog or the instruction manual when installing equipment, etc.4. Do not re-use gaskets unless this is specifically indicated.5. When replacing, carefully remove all of the old material before installing the new product.6. To maintain performance, store packaged products in a cool and dark place.7. Please refer to MSDS (Material Safety Data Sheet) concerning health and hygiene cautions.8. When disposing, comply with all regulations in your country. Waste should be properly disposed of at a permitted
disposal site. Do not incinerate the used products, especially those containing fluoropolymer resin as it will generatetoxic gas when burning.
¡TOMBO“TOMBO” is a registered trademark of NICHIAS Corporation.
¡JIS Japanese Industrial Standards
¡JPI The Japan Petroleum Institute
¡ASME American Society of Mechanical Engineers
¡API American Petroleum Institute
¡BS British Standards
¡ISO International Organization for Standardization
*All brand names and product names are trademarks or registered trademarks of NICHIAS Corporation.
CAUTIONS!
Safe UsagePlease observe the following in order to obtain the full function of the
products and to ensure safe usage.
Explanatory notes for customersThe following signs and abbreviations are used in this catalogue.
2
In this catalog, the fluids sealed with gaskets are classified as follows.Depending on the type of gasket, however, there are various cases where one typeof gasket cannot always be used in the same way for the same fluid.
(1) Water type fluids Water, brine, hot water, steam, superheated steam.
(2) Oil type fluidsCrude oil, volatile oil, naphtha, kerosene, heavy oil, LPG, alcohol, furfural,ethylene glycol, ethylene, prophylene, B-B fraction, butadiene, liquid ammonia,phenol, acrylonitrile, acetone, acetoaldehyde, benzene, toluene, xylene,ethylbenzene, cyclohexane, tetramethysulphon, tetraethyl lead, etc.
(3) Corrosive fluidsAcids such as mineral acids, organic acids, mixed acids, acidic solutions, etc.,and alkalis.
(4) Gas type fluidsAir, nitrogen gas, combustible gas, combustion promoting gas, incombustiblegas, toxic gas, etc.Places where there is little danger even with some leakage amount of air,nitrogen gas, etc., may also be considered safe like water type fluids; however,the necessary tightening pressure must be secured.
(5) Low-temperature fluidsLPG, liquid ethylene, LNG, liquid nitrogen, liquid air, etc.
Normally, the Wm1 and Wm2 (refer to the equation below) specified in JIS B 8265,etc., may be used as the criterion for determining the required seating stress.
Wm1= G2P+2πbGmP
Wm2=πbGyP = internal pressureG = effective gasket diameterb = effective gasket widthm= gasket factory = minimum designed seating stress
In some cases, however, this seating stress may not be sufficient depending oncertain types of fluids and or certain types of gaskets. So, among the three seatingstresses (Wm1, Wm2, Wm3), the largest value shall be employed as the minimumseating stress.Wm3=σ3 Ag
σ3= minimum seating stressAg = gasket contact area (projected surface area)
The minimum seating stresses used in this catalog is "σ3" in the aboveequation, and not "y".
π–4
Minimum Seating Stress
Fluids
Definitions of Terminology
3
1Fluid
Steam
Hot water
Water
Salt water
(Brine)
Petroleum-
based
carbonatedhydrogen
Gasoline
Naphtha
Kerosene
Light oil
Heavy oil
Lubricating oil
Oil gas
LPG
Alcohol
Animal andvegetable oils
2Temperature(℃)
3Pressure
MPaTOMBO� No. Product name
Remarks
Operating conditions Recommended gasket
18 1850C-G Ring Joint Gasket600
18 1836R-GS Vortex Gasket GS29 1850C-F Ring Joint Gasket
45029 1834R-GR GRASEAL Vortex Gasket
400 3.6 1215,1210-A GRASEAL Gasket PM, MI-A34 1850C-F Ring Joint Gasket
350 34 1834R-GR GRASEAL Vortex Gasket12 1834R-NA NA Vortex Gasket39 1850C-F Ring Joint Gasket
260 39 1834R-GR GRASEAL Vortex Gasket14 1834R-NA NA Vortex Gasket
215 2.0 1120 CLINSIL-Top1.5 9007-LC NAFLON PTFE Low Creep Gasket
2001.5 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket1.0 9007-G20 Glass Fiber Filled PTFE Cut Gasket
1501.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket44 1850C-F Ring Joint Gasket44 1834R-GR GRASEAL Vortex Gasket16 1834R-NA NA Vortex Gasket
100 4.0 1120 CLINSIL-TOP1.8 1995 CLINSIL-Brown1.0 1051-CR Cloth Reinforced Rubber Cut Gasket0.5 9007 NAFLON PTFE Cut Gasket18 1850C-G Ring Joint Gasket
60011 1836R-GS Vortex Gasket GS29 1850C-F Ring Joint Gasket
45017 1834R-GR GRASEAL Vortex Gasket
400 3.6 1215,1210-A GRASEAL Gasket PM, MI-A34 1850C-F Ring Joint Gasket
350 21 1834R-GR GRASEAL Vortex Gasket8.0 1834R-NA NA Vortex Gasket39 1850C-F Ring Joint Gasket23 1834R-GR GRASEAL Vortex Gasket
2609.0 1834R-NA NA Vortex Gasket1.0 1120 CLINSIL-Top1.5 9007-LC NAFLON PTFE Low Creep Gasket
2001.5 9007-SC NAFLON PTFE Special Filler Filled Cut Gasket1.0 9007-G20 Glass Fiber Filled PTFE Cut Gasket
1501.0 9010-NA-A-7 NAFLON PTFE Cushion Gasket44 1850C-F Ring Joint Gasket26 1834R-GR GRASEAL Vortex Gasket11 1834R-NA NA Vortex Gasket
100 3.0 1120 CLINSIL-Top1.8 1995 CLINSIL-Brown0.5 9007 NAFLON PTFE Cut Gasket0.5 9007-LP NAFLON PFA Gasket
Gasket SelectionPlease select a gasket from the following gasket selection table considering 1fluid, 2pressure and 3temperature.
*This selection guide shows typical recommended gaskets for fluids, temperatures and pressures.
Thus, depending on the other conditions, the products shown here are not necessarily suitable for use in some cases.
*Please refer to service temperature range of each gasket on this catalog regard the maximum service temperature.
*In some cases, the product numbers shown here are only representative examples for that type.
4
Aromatics-
based
carbonated
hydrogen
Benzene
Toluene
Xylene
Organic
solutions
Heat transfersolutions
Weak acid
Weak alkali
Salt solutions
AcidsSulphuric acid
Hydrochloric acid
Nitric acid
Acetic acid
18 1850C-G600
11 1836R-GS29 1850C-F
45017 1834R-GR
400 3.6 1215,1210-A34 1850C-F
350 21 1834R-GR8.0 1834R-NA39 1850C-F
260 23 1834R-GR9.0 1834R-NA1.5 9007-LC
2001.5 9007-SC1.0 9007-G20
1501.0 9010-NA-A-744 1850C-F26 1834R-GR11 1834R-NA
100 3.0 9007-LC1.8 9010-NA-A-5,70.5 90070.5 9007-LP9.0 1834R-GR9.0 1834R-NA
2604.6 1215,1210-A1.0 1120 1.5 9007-LC
2001.5 9007-SC1.0 9007-G20
1501.0 9010-NA-A-711 1834R-GR11 1834R-NA
100 1.8 11201.8 19950.5 9007
260 9.0 9090-IOR1.5 9007-LC
2001.5 9007-SC1.0 9007-G20
1501.0 9010-NA-A-711 9090-IOR1.8 9007-LC
1001.0 9010-NA-A-5,70.5 9007
Ring Joint GasketVortex Gasket GSRing Joint GasketGRASEAL Vortex GasketGRASEAL Gasket PM, MI-ARing Joint GasketGRASEAL Vortex GasketNA Vortex GasketRing Joint GasketGRASEAL Vortex GasketNA Vortex GasketNAFLON PTFE Low Creep GasketNAFLON PTFE Special Filler Filled Cut GasketGlass Fiber Filled PTFE Cut GasketNAFLON PTFE Cushion GasketRing Joint GasketGRASEAL Vortex GasketNA Vortex GasketNAFLON PTFE Low Creep GasketNAFLON PTFE Cushion GasketNAFLON PTFE Cut GasketNAFLON PFA GasketGRASEAL Vortex GasketNA Vortex GasketGRASEAL Gasket PM, MI-ACLINSIL-TopNAFLON PTFE Low Creep GasketNAFLON PTFE Special Filler Filled Cut GasketGlass Fiber Filled PTFE Cut GasketNAFLON PTFE Cushion GasketGRASEAL Vortex GasketNA Vortex GasketCLINSIL-TopCLINSIL-BrownNAFLON PTFE Cut GasketNAFLON Vortex GasketNAFLON PTFE Low Creep GasketNAFLON PTFE Special Filler Filled Cut GasketGlass Fiber Filled PTFE Cut GasketNAFLON PTFE Cushion GasketNAFLON Vortex GasketNAFLON PTFE Low Creep GasketNAFLON PTFE Cushion GasketNAFLON PTFE Cut Gasket
Gasket Selection
1Fluid 2Temperature(℃)
3Pressure
MPaTOMBO� No. Product name
Remarks
Operating conditions Recommended gasket
5
Gasket Selection
1Fluid
AlkaliCaustic sodaCausticpotassium
Air
Exhaust gas
Combustiblegas
Toxic gas
Hydrogen gas
Ammonia
Oxygen gas
Low-temperature fluids Liquid gas LNG, LN2 LO2, Ethylene
2Temperature(℃)
3Pressure
MPaTOMBO� No. Product name
Remarks
Operating conditions Recommended gasket
9.0 1834R-GR2604.6 1215,1210-A
200 1.5 9007-SC150 1.0 9010-NA-A-7
11 1834R-NA1.8 9007-SC
100 1.8 11201.0 9010-NA-A-5,70.5 9007
600 0.3 1841-Fi-G300 5.0 1834R-GR260 1.0 1120
1.5 9007-LC200 1.5 9007-SC
1.5 9010-NA-A-91.0 9007-G20
150 1.0 9010-NA-A-71.0 1995
100 1.0 1050-EP0.5 9007
700 0.01 1400-ST500 0.01 1400-TH300 0.01 1374200 1.0 1120100 1.0 1995600 18 1850C-G
29 1850C-F450 17 1834R-GR
34 1850C-F350 21 1834R-GR
5.0 1834R-NA39 1850C-F23 1834R-GR
260 9.0 9090-IOR6.0 1834R-NA
200 1.5 9007-LC1.0 9007-G20
150 1.0 9010-NA-A-70.5 9007
100 0.5 9007-LP39 1850C-F2609.0 9090-IOR-OX1.8 9010-NA-A-51001.8 9007-LC20 1834R-GR
-240 11 1839R-200 1.0 1120-LN
GRASEAL Vortex GasketGRASEAL Gasket PM, MI-ANAFLON PTFE Special Filler Filled Cut GasketNAFLON PTFE Cushion GasketNA Vortex GasketNAFLON PTFE Special Filler Filled Cut GasketCLINSIL-TopNAFLON PTFE Cushion GasketNAFLON PTFE Cut GasketHigh-temperature NA Metal Jacketed GasketGRASEAL Vortex GasketCLINSIL-TopNAFLON PTFE Low Creep GasketNAFLON PTFE Special Filler Filled Cut GasketNAFLON PTFE Cushion GasketGlass Fiber Filled PTFE Cut GasketNAFLON PTFE Cushion GasketCLINSIL-BrownRubber Cut gasketNAFLON PTFE Cut GasketSuper Manhole Gasket-STFF Manhole GasketNA Manhole GasketCLINSIL-TopCLINSIL-BrownRing Joint GasketRing Joint GasketGRASEAL Vortex GasketRing Joint GasketGRASEAL Vortex GasketNA Vortex GasketRing Joint GasketGRASEAL Vortex GasketNAFLON Vortex GasketNA Vortex GasketNAFLON PTFE Low Creep GasketGlass Fiber Filled PTFE Cut GasketNAFLON PTFE Cushion GasketNAFLON PTFE Cut GasketNAFLON PFA GasketRing Joint GasketNAFLON Vortex GasketNAFLON PTFE Cushion GasketNAFLON PTFE Low Creep GasketGRASEAL Vortex GasketGRASEAL Vortex Gasket LCLINSIL-Top LN
Used together with high-temperature gasket paste.
Used together with gasket paste.
Suitable for applications where slight leakage is permissible.Suitable for applications where slight leakage is permissible.Suitable for applications where slight leakage is permissible.
6
HIG
H T
EMPE
RA
TUR
E U
SE
SH
EETS
GA
SK
ETS
■High Temperature Use Sheet GasketThis is newly developed non-asbestos gasketing sheet for high temperature
application. Main material of expanded graphite is mixed with aramid fibers,
rubber and chemicals and then processed by calendering machine.
NA Joint Sheets for High Temperature
CLINSILTM
-Top TOMBO� No.1120
■Features : ¡It can be used from –200℃ to 260℃ at 1MPa condition.¡This gasket can be used for 2MPa saturated steam.¡Seal performance and chemical resistance are quite
similar to conventional asbestos joint sheets.¡"m" and "y" value are the same as asbestos joint sheets.¡Maximum outer diameter is 2520 mm and irregular
shapes are available. ¡Not like graphite sheet, surface is not scratched by
normal handling process. Also good in flexibility.¡Thanks to the flexibility of expanded graphite, bolt
re-tightening is possible.¡It will not cause corrosion pitching when it is used for
stainless steel flange.¡100% asbestos-free product.
■Applications : Gaskets for various types of piping flanges, valves,equipment etc.For cryogenic application like LNG, TOMBO No. 1120-LN with specialtreatment is recommended to use.
■Service Range (For details, please refer to thediagram on page 10)¡Temperature : –200℃~ 260℃¡Pressure : Saturated steam, hot water
→See Page 10Water, salt solutions, weak acid and weak alkali solutions.→Max.4.0MPa {30Of/F}Oil at 120℃ or lower.→Max.4.0MPa {30Of/F}Air, exhaust gas, inert gas.
→Max.1.0MPa {10Of/F}
■Applicable standardsTA LUFT/VDI GUIDE LINE 2440 (HELIUM LEAKAGE)
■Availability
■Recommended seating stress of Gasket : Please refer to page 8.
■Chemical resistance : CLINSIL-Top (TOMBO No.1120)
Asbestos joint sheet (TOMBO No.1100)
Tensile strength(N/mm2 )
After submersion
Before submersion
Hydrochloric Acid (20%-70℃)
Sulfuric Acid (10%-65℃)
Sodium Hydroxide (30%-70℃)
Ammonia Water (30%-RT)
0.0
5.0
10.0
15.0
20.0
25.0
30.0
*submersion hour : 22hr For other fluids, verification test may be necessary. Please consult us for details.
■Functional performance versus steam Typical test data in steal line
<Condition>Temperature : 215℃Pressure : 2MPaFluid : SteamGasket Thickness : 1.5mmFlange : JIS20K 25A RFFastening Surface Pressure : 29.4MPaVenue : Boiler at Nichias' factory
<Result>776days No leakageTest under implementation as of May in 2008
TOMBO No. 1120
■Fluids not suitable for use with Clinsil-Top.Type Fluid name
Oxidizing acids Nitric acid, concentrated sulphuric acid, hot sulphuric acid, mixed acids, chromic acid,etc.
Oxidizing salts Nitrate, chlorate, hypochlorite, etc.Halogen compounds Bromine, fluorine, iodine, chlorine dioxide, etc.Combustion promoting gas Oxygen (pure oxygen)
!
!Handling instructionsSince gaseous fluids have a higher tendency to leak than water-based and oil-based fluids, please pay attention to and follow the handlinginstructions below.¡Gaskets should be ring-shaped (Type FR) in thickness of 1.5mm or less.¡Apply a small amount of the gasket paste (TOMBO No. 9105, 9106) thinly and evenly to the inner edge and both faces of gasket.¡When gasket is tightened in place, do not tighten more than the tolerable seating stress.
Pay attention to the tendency that seating stress becomes greater than the tolerance in the case of flanges in small diameter.¡Pay attention to the tendency that seating stress at compression failure declines less than the values shown on page11 in the case where gasket
is tightened under elevated temperatures (hot bolting).
Width×Length Thickness0.4 0.5 0.8 1.0 1.5 2.0 3.0
1270×1270 (1S) ○ ○ ○ ○ ○ ○ ○1270×3810 (3S) ○ ○ ○ ○ ○ ○ ○2540×3810 (6S) ― ― ― ○ ○ ○ ○
7
JO
INT
SH
EE
TS
■JOINT SHEETSCompressed fiber joint sheet is a gasket made of a uniform mixture of fibrous material, filler, rubber and
chemicals which is hot rolled by calendering to obtain smooth sheets. The sheets are processed to the required
shapes and dimensions for applications in equipment, etc., in a wide range of industries.
General-purpose NA Joint Sheets
CLINSILTM
-Brown TOMBO� No.1995
NA Joint Sheets for Stream
CLINSILTM
-Super TOMBO� No.1993
■Features : The main components are inorganic fibers towhich inorganic filler and aramid fibers are added; oil-resistant synthetic rubber is then added as binder to formgreen NA (non-asbestos) joint sheets, which containabsolutely no asbestos.This gasket can be used for stainless steel flange sinceleachable halogens are little.
■Applications : Gaskets for various types of pipingflanges and valves, equipment, etc.
■Service Range (For details, please refer to thediagram on page 10.)¡Temperature : –100℃~ 215℃¡Pressure : Saturated steam, hot water
→See Page 10Water, salt solutions, weak acid and weakalkali solutions. →Max.3.0MPaOil at 100℃ or lower.→Max.3.0MPa}Air, exhaust gas, inert gas.
→Max.1.0MPa
■Applicable standardsJIS F 0602 HJ BAM OXYGEN GAS SERVICE
ASTM F104 F712100-B5E12M5JIS F 7102 HJ
■Availability
TOMBO No. 1993Caution for Steam Sealing more than120℃¡Use ring shape (FR) and 1.5A gasket.¡Minimum recommended compressive stress
for TOMBO No. 1993 is 29.4N/E.¡Use Vortex gaskets, etc. in places where
maintenance is difficult.¡Re-torque immediately before temperature
rise.¡Do not re-torque after temperature rise.¡Avoid piping stress to installed gaskets.Handling instructions in the case wheregasket is for use in gas line.
¡Do not use this gasket for applications whereeven a minimal amount of leakage is notallowable.
!
!
TOMBO No. 1995
Caution for Steam Sealing more than 100℃¡Use ring shape (FR) and 1.5A gasket.¡Minimum recommended compressive stress for TOMBO
No. 1995 is 29.4NE¡TOMBO No. 1993 is recommended when maximum
operating pressure is 0.5MPa and over.¡Use Vortex gaskets, etc. in places where maintenance is
difficult.¡Re-torque immediately before temperature rise.¡Do not re-torque after temperature rise.¡Avoid piping stress to installed gaskets.
!
■Features : Inorganic filler is added to inorganic fibersand aramid fibers; then oil-resistant synthetic rubber isadded as binder to form brown NA (non-asbestos) jointsheets which contain absolutely no asbestos.This gasket can be used for stainless steel flange sinceleachable halogens are little.Large diameter gasket cut from the sheet of 3,810mm x3,810mm (9Ssize) max. in monolithic form is available.
■Applications : Gaskets for various types of pipingflanges and valves, equipment, etc.
■Service Range (For details, please refer to thediagram on page 10.)¡Temperature : –100℃~ 183℃¡Pressure : Saturated steam, hot water
→See Page 10Water, salt solutions, weak acid andweak alkali solutions.→Max.3.0MPaOil at 100℃ or lower.→Max.3.0MPaAir, exhaust gas, inert gas.
→Max.1.0MPa■Applicable standards
API 6FA (FIRESAFE) BAM OXYGEN GAS SERVICEGERMANISCHER LLOYD GL TYPETA LUFT/VDI GUIDE LINE 2440 (HELIUM LEAKAGE)ASTM F104 F712100-B5E12M5JIS F 0602 HJ JIS F 7102 HJ■Availability
Width×Length Thickness0.8 1.0 1.5 2.0 3.0
1270×1270 (1S) ○ ○ ○ ○ ○1270×3810 (3S) ○ ○ ○ ○ ○2540×3810 (6S) ─ ○ ○ ○ ○3810×3810 (9S) ─ ─ ○ ○ ○
Width×Length Thickness0.5 0.8 1.0 1.5 2.0 3.0
1270×1270 (1S) ○ ○ ○ ○ ○ ○1270×3810 (3S) ○ ○ ○ ○ ○ ○
8
JO
INT
SH
EE
TS
Other Joint Sheets
■Recommended Seating Stress of Gasket
1938 CLINSIL-UF
Aramid fibers, inorganic fibers, inorganic filler andoil-resistant rubber are mixed uniformly and thencompressed and calendered to form NA (non-asbestos) joint sheets with outstanding shearstrength and easy cutting feature.
TOMBO No. Product name Construction and featuresAppearance
1991-NF CLINSIL-NF
NA (non-asbestos) joint sheet for refrigerator.Suitable to use with POE(ester oil) or combinationof R134a / POE.Tensile strength and gas sealing performance isalmost same as our TOMBO No.1901 and totaloxidation from gasket is quite minimum.
Thickness – – – 1.0 1.5 2.0 –
Width×Length 1270×1270 (1S)
Thickness 0.4 0.5 0.8 1.0 – – –
Width×Length 1270×1270 (1S)1270×3810 (3S)
■AvailabilityTOMBO� No.1938 TOMBO� No.1991-NF
Compressed Fiber Joint Sheet Standards and Physical Properties(Test data only)
*Test sample thickness: 1.5A (1.0A for TOMBO No.1991-NF)
0.81.53.0
Thickness(mm)
Gasket factorm (-)
Minimum designed seating stressy (N/mm2)
Minimum seating stressWater・Oil type Fluids (N/mm2) Gas type Fluids (N/mm2)
3.502.752.00
44.825.511.0
14.714.714.7
34.334.3-
Tensile strengthCompressibilityRecovery
Flexibility
Oil resistance
Steam test
Fuel oil resistance
Density
Ignition loss
Stress relaxation
34.3N/E
N/E 15.7min7~1745 min
No cracks–
30 max40 max
––––
––
––
50 max
28 max
40 max
–
9.8min5~1935 min
No cracks–
30 max40 max
––––
––
–––
–
50 max
–
%%
WarpWeft
Increase in thickness %Decrease in tensile strength %
Increase in thickness %Increase in weight %Compressibility %Recovery %
Increase in thickness %Increase in weight %
Compressibility %Recovery %Decrease in tensile strength %
%
%
N/ J
By a round rod witha diameter of 12times the thickness.
IRM 903 oil150℃× 5h
IRM 903 oil40℃× 48h
ASTM Fuel B(JIS fuel oil B)
R. T.× 5h
5.0Mpa× 1h
850℃× 0.5h
100℃× 22h
JIS R 3453-2001
Class A Class B
Applicable standards
Test Item
9
JO
INT
SH
EE
TS
–100 ~ 100JIS F 0602 HJASTM F104 (F712100)
Union jointsFluid: water, hot water, gas
–100 ~ 180JIS F 0602 HJASTM F104 (F712100-M7)
Refrigerator compressors and relatedequipmentFluid: substitute freon, refrigerator oil
Service temperature range
(℃)Applicable standardsApplication
23.5min12±547 min
No cracksNo cracks
––
20 max15 max20 max40 min
––
23 max38 min
–
28 max
40 max
1.7~2.0
27.5970
No cracksNo cracks
211
––––
21
105021
–
25
1.53
TOMBO No. 1120
14.7752
No cracksNo cracks
2433
––––
1817
–––
–
20
1.71
TOMBO No. 1993
24.1765
No cracksNo cracks
323
44664
46
–––
30
28
1.84
TOMBO No. 1995
21.6755
No cracksNo cracks
10
––––
34
–––
–
26
1.80
TOMBO No. 1938
23.56
65
No cracksNo cracks
1-1
166
73
35
–––
–
27
1.59
30.47
66
No cracksNo cracks
2233
897
66
1612
8566
24
27
1.86
TOMBO No. 1991-NFAsbestos joint sheet(TOMBO No.1100)
*ReferenceTest data
JPI-7S-4-1998
JO
INT
SH
EE
TS
10
Service Range
120℃
215℃
183℃
0
1.0
2.0
3.0
4.0
5.0
6.0
Fluid temperature(℃)
Flu
id p
ress
ure
(M
Pa)
0 50 100 150 200 250
A
B
TOMBO�
No.1993 CLINSILTM
-Super
¡Water type fluids
Note: Recommended gasket lifefor steam sealing is as follows:A: 5 ~ 10 yearsB: 1 ~ 2 years
0
1.0
2.0
3.0
4.0
5.0
6.0
Fluid temperature(℃)
Flu
id p
ress
ure
(M
Pa)
0 50 100 150 200 250
¡Oil type fluids
Note: Do not use for aromatic-based fluids.
0
1.0
2.0
3.0
4.0
5.0
6.0
Fluid temperature(℃)
Flu
id p
ress
ure
(M
Pa)
0 50 100 150 200 250
¡Gas type fluids
Note: Do not use for toxic gasesor combustion promoting gas(oxygen).
1~2 years
0
1.0
2.0
3.0
4.0
5.0
6.0
Fluid temperature(℃)
Flu
id p
ress
ure
(M
Pa)
0 50 100 150 200 250
TOMBO�
No.1995 CLINSILTM
-Brown
¡Water type fluids
Note:Recommended gasketlife for steam pipe sealing at100℃ or above is as follows:
0
1.0
2.0
3.0
4.0
5.0
6.0
Fluid temperature(℃)
Flu
id p
ress
ure
(M
Pa)
0 50 100 150 200 250
¡Oil type fluids
Note: Do not use for aromatic-based fluids.
0
1.0
2.0
3.0
4.0
5.0
6.0
Fluid temperature(℃)
Flu
id p
ress
ure
(M
Pa)
0 50 100 150 200 250
¡Gas type fluids
Note: Do not use for toxic gasesor combustion promoting gas(oxygen).
120℃
215℃
0
1.0
2.0
3.0
4.0
Fluid temperature(℃)
Flu
id p
ress
ure
(M
Pa)
0 50 100 150 200 250 280
TOMBO�
No.1120 CLINSILTM
-Top
¡Water type fluids
120℃
200℃
260℃
0
1.0
2.0
3.0
4.0
Fluid temperature(℃)
Flu
id p
ress
ure
(M
Pa)
0 50 100 150 200 250 280
¡Oil type fluids
260℃
0
1.0
2.0
3.0
4.0
Fluid temperature(℃)
Flu
id p
ress
ure
(M
Pa)
0 50 100 150 200 250 280
C
¡Gas type fluids
*Please consult us for the service other than the above service range.
*For steam higher than 100℃, hot water, please refer to cautions in page 7.
*For steam higher than 120℃, hot water, please refer to cautions in page 7.
Note : Do not use for toxic gases orcombustion promoting gas(oxygen).C : Use ring shape(FR), thickness
less than 1.5mm, with gasketpaste, with adequate fastening.
11
JO
INT
SH
EE
TS
■Flange Finish The recommended surface roughness of flange isas follows :¡For liquids 6.3 Ra
¡For gas 3.2 Ra
■Seating Stress The seating stress should be one the maximum value, as
shown below:a. Wm1 according to JIS B 8265.b. Wm2 according to JIS B 8265.c. Minimum seating stress required for sealing
liquids.¡For water, oil : 14.7N/E¡For gas : 34.3N/E
■Preventive measures for permeation leakageof gaseous fluidsThe joint sheet has disadvantage that it has a high
tendency to have permeation leakage in the case ofgaseous fluids since it is not physically dense materialdue to the characteristics of its material component.¡Apply a small amount of gasket paste uniformly
on the surface and inner diameter.¡Apply enough seating stress.(Please refer above.)¡Gaskets should be ring-shaped (FR shape) with a
thickness of 1.5A or less.¡When an air tight test is required, 2-3 hours after
tightening.¡Non-asbestos joint sheet shall not be used for
toxic gas or high vacuum sealing.
■Non-asbestos Joint Sheets for stainless steelflangesTOMBO No.1993, 1995, 1120 are recommended forthis service since leachable halogens are little.Gasket paste (TOMBO No.9120) is not requiredgenerally. However, if paste is used, please consult us.
■Compression failure¡Fastening force
If excessive tightening force is applied to non-asbestos joint sheets, compression failure mayoccur. When tightening joint sheets, refer to thefollowing maximum tolerable seating stress.
Cautions
Bolt tightening sequence
1
7
4
6 2
8
3
5
■Installation Tighten bolts from side to side around the joint in astar like crossing pattern.All bolts should be tightened in four to fiveincrements, according proper bolting patterns.Immediate tightening can cause leaks andcompression damage.
■Gasket ThicknessWe recommend the use of gasket thicknessdepending on the nominal diameter of the flange asfollows.150A (6B) or below: 1.5A200A (8B) and above: 3.0A
Caution¡We recommend a thickness of 1.5At regardless of
the consideration above if TOMBO No.1995 isused for steam or hot water at the temperature ofover 100 .゚
¡We recommend a thickness of 1.5At regardless ofthe consideration above if TOMBO No.1993 isused for steam or hot water at the temperature ofover 120 .゚
■Placing orders¡Sheets
Please specify the thickness, width and length.Example: 1.5t×1270×1270 or 1.5t×1S.
¡Cut gasketsIn the case of flanges for JIS or JPI (ANSI) piping,etc., please specify pressure rating (class),nominal diameter, flange type (RF or FF) andgasket thickness.Example: JIS 10K×50A, RF, 1.5t,
JPI class 150×2B, RF, 1.5t.Please provide a drawing for non-standarddimensions.
Caution¡These joint sheet gaskets contain organic
materials; therefore they are not recommended forcombustion promoting application gas (oxygengas).
¡For further details, please refer to the separatehandling instructions.
ThicknessA
NA joint sheetTOMBO No.
Without pasteN/E
With pasteN/E
1120 0.8 294.2 68.6 1995 1.5 196.1 68.6 1993 3.0 147.1 68.6
Due to low physical strength of NA joint sheets,special precautions should be made to avoiduneven tightening.
¡Combined use of gasket pasteDo not apply solvent-based liquid packing (whichmakes gaskets swell), silicon-based oil or grease(which makes gaskets slippery) on NA joint sheetsas gasket paste, as they may cause compressionfailure at a pressure lower than the above valuesof seating stress.If using gasket paste, TOMBO No. 9105 or 9106 isrecommended.Please consult with us regarding other pastes.
!
Maximum tolerable seating stress
Value inside ( ) is for TOMBO No. 1120
!
12
VO
RT
EX
GA
SK
ET
S
■VORTEXTM
GASKETSVortex gaskets are semi-metallic gaskets. Owing to their special
construction, Vortex gaskets can be used at high temperatures and high
pressures like metal gaskets. Sealability is outstanding and a wide application
range is possible for various types of piping and equipment.
■ConstructionVortex gaskets are made of thin V-shaped metalhoops and non-metallic cushioning filler. These arewound into a spiral shape by welding at the beginningand end of the spiral winding. Vortex gaskets areavailable in four types: basic, with an inner ring, withan outer ring, and with both inner and outer rings.
■Types and TOMBO Numbers
■Applicable standards¡JIS F 0602
Shipbuilding – Non asbestos gaskets to cargo pipingsystem – Application standard.HUC TOMBO No.1834-NAHUD TOMBO No.1834R-NAKUD TOMBO No.1834R-GRFUC TOMBO No.9090-IOR
¡JIS F 7102Shipbuilding – Piping system in machinery space- Application for gaskets and packings.HUC TOMBO No.1834-NAHUD TOMBO No.1834R-NAKUD TOMBO No.1834R-GR
¡JPI-7S-41Spiral wound gaskets for petroleum industry.TOMBO No.1804 SeriesTOMBO No.1804-GR SeriesTOMBO No.9090 Series
■Applicable standards¡ASME B 16.20
Metallic gaskets for pipe flange joint. Spiral woundand jacketed.
¡API 601 (OLD VERSION)Metallic gaskets for raised face pipe flanges andflanged connections.(Double jacketed corrugated and spiral-wound)
¡BS 3381Metallic spiral-wound gaskets for use with flanges toBS 1560, Parts 1 and 2.
¡ISO 7483Dimensions of gaskets for use with flanges to ISO7005.
Type 304 stainless steel 1804-GR 1804-NABasic type Type 316 stainless steel 1806-GR 1806-NA
Other 1808-GR 1808-NAType 304 stainless steel 1804R-GR 1804R-NA
With inner ring Type 316 stainless steel 1806R-GR 1806R-NAOther 1808R-GR 1808R-NA
Type 304 stainless steel 1834-GR 1834-NAWith outer ring Type 316 stainless steel 1836-GR 1836-NA
Other 1838-GR 1838-NAType 304 stainless steel 1834R-GR 1834R-NAType 316 stainless steel 1836R-GR 1836R-NA
Other 1838R-GR 1838R-NA
Shape Hoop material
Filler material
Expandedgraphite tape NA paper PTFE tape
Expanded graphite tape+
Mica paper
With both innerand outer rings
-------- -------- --------9090 1806-GS 1806-GM --------
1808-GS 1808-GM 1808-GH------ -------- --------
9090-IR 1806R-GS 1806R-GM --------1808R-GS 1808R-GM 1808R-GH
------ -------- --------9090-OR 1836-GS 1836-GM
1838-GS 1838-GM 1838-GH------ -------- --------
9090-IOR 1836R-GS 1836R-GM --------1838R-GS 1838R-GM 1838R-GH
Notes: TOMBO Numbers shown in this table indicate normal shaped gaskets with representative fillers for piping. Special shapes, etc., will differ from these. Refer to page 28 for details.
1804-GR series 1804-NA series 9090 series 1806-GS series 1806-GM series 1808-GH series
13
VO
RT
EX
GA
SK
ET
S
■Shape¡Basic type
Vortex gaskets are made of thin metal hoops andnon-metallic cushioning filler. These are woundinto a spiral shape by welding at the beginning andend of the spiral windings. This type is used for Male & Female (M&F) typeflanges and Tongue and Groove (T&G) typeflanges, but is not recommended for the raised faceof ordinary piping flanges.
¡With inner ring typeA metallic inner ring is added to the basic typeVortex gasket.The inner ring functions as reinforcement thatprevents deformation of the gasket duringtightening. These are used for Male & Female(M&F) type flanges and valve bonnet gaskets.
¡With outer ring typeA metallic outer ring is added to the basic typeVortex gasket.The outer ring functions to center the Vortex gasketwhen it is placed in flanges and also to preventdeformation of the gasket during tightening. Thistype is used for raised face (RF) piping flanges.With inner and outer ring type is recommended forthe following cases:¡High-pressure such as class 900 or 63K and
above.¡Large diameter such as 26” and above.¡GRASEAL and NAFLON filler.
¡With inner and outer ring typeAn inner ring is added to the type with outer ring.The inner ring protects spiral wound gaskets frombuckling during tightening.
Cross section of the basic type Vortex gasket
Filler Hoop
Cross section of the Vortex gasket with an inner ring
Filler Hoop Inner ring
Cross section of the Vortex gasket with an outer ring
Filler HoopOuter ring
Cross section of the Vortex gasket with both inner and outer rings
Filler Hoop Inner ringOuter ring
14
VO
RT
EX
GA
SK
ET
S
Fluid Maximum servicetemperature℃
Expanded Graphite Tape Filler Vortex Gaskets
GRASEALTM
Vortex Gasket TOMBO� No. 1804-GR Series
This Vortex gasket uses expanded graphite tape (GRASEAL tape) as thefiller material which provides superb sealability even under severeconditions such as high temperatures, high pressures, cryogenictemperatures, heat cycles, temperature cycles and so on.
■Features1. Sealability, especially gas sealing, is superior to that of NA Vortex gaskets.2. Good sealability under high temperature and pressure since filler materials are
less affected by high temperature.3. Sealability remains outstanding even under severe conditions such as pressure
fluctuations and heat cycles.4. As filler materials is also chemical resistant, gasket with appropriately selected
hoop can be used for corrosive fluids in situations where asbestos cannot be used.5. Outstanding Sealability even at cryogenic temperatures.
■ApplicationsSuitable for use in piping flanges, pressure vessels, heat exchangers, valvebonnets, etc., in various industries, especially as gasket for high-temperature,high-pressure steam, and for LNG, etc. at cryogenic temperatures.
TOMBO No. 1834R-GR■Service Range
NA Paper Filler Vortex Gaskets
NA VortexTM
Gasket TOMBO� No. 1804-NA Series
Instead of the conventional asbestos filler, this type of Vortex gasket uses inorganic fibers andaramid fibers as a non-asbestos paper filler.
■Features1. Asbestos fibers are not used.2. The service range (heat resistance, pressure resistance)
is different from that of the asbestos Vortex gaskets, .but the sealing performance is almost the same.
■ApplicationsSuitable for use in piping flanges, pressure vessels, heatexchangers, valve bonnets, etc.
Please pay attention when flanges are released after temporarysetting of machinery or hydraulic test. Filler material may stick toflanges. Please consult us if gaskets are used like this.
Maximum service pressure
* The values in brackets ( ) are maximum service temperaturesunder a non-oxidizing atmosphere. When using with RF flangesin open air, the maximum service temperature is 450℃.
* Max. service temperature differs depending on the materials ofthe hoop and the inner and outer rings. Refer to page 27. Do notapply gasket paste.
Water type fluids 450(650) Class 2500Oil type fluids 450(800) Class 1500Gas type fluids 450(800) Class 1500Cryogenic –240 20MPatemperature fluids (Minimum service temperature)
Fluid Maximum servicetemperature℃
TOMBO No. 1834-NA■Service Range
Maximum service pressure
Water type fluids 350 Class 1500Oil type fluids 350 Class 600Gas type fluids 350 Class 400
Fluids not suitable for use with GRASEAL
Classification Name of liquid
Oxidizing acid Nitric acid, Concentrated sulfuric acid, Hot sulfuricacid, Chromic acid, Mixed acids, etc.
Oxidized salt Nitrates, Chlorates, Hypochlorites, etc.Halogen compounds Bromine, Fluoride, Iodine, Chlorine dioxide, etc.Combustion promoting gas Oxygen (Pure oxygen)
15
VO
RT
EX
GA
SK
ET
S
PTFE Tape Filler Vortex Gaskets
NAFLONTM
Vortex Gasket TOMBO� No. 9090 Series
This Vortex gasket uses unsintered PTFE tape asthe filler material. The PTFE filler providessuperior chemical resistance and sealability. Bycombining with corrosion resistant metals, it canbe applied for corrosive fluids, pure oxygen gasand vacuum lines.
■Features1. Sealability is superior to that of all other Vortex
gaskets. It can also be used for vacuum lines.2. The highest corrosion resistance among the all Vortex
gaskets. It can be used for almost all fluids by selectingappropriate hoop materials
■ApplicationsSuitable for use in piping flanges, pressure vessels, heatexchangers, valve bonnets, etc. especially for corrosivefluids and oxygen for which other Vortex gaskets cannotbe used, places where a high degree of air tightness isrequired, as well as vacuum lines.The OX type, which has no oil in the PTFE, is available foruse with pure oxygen.
TOMBO No. 9090-IOR
Fluid Maximum servicetemperature℃
■Service RangeMaximum service
pressure
Water type fluids 300 Class 600Oil type fluids 300 Class 600Gas type fluids 300 Class 600
16
VO
RT
EX
GA
SK
ET
S
Notes: Maximum service temperatures differ depending on the materials of thehoop and the inner and outer rings. Refer to page 27.
Fluid
TOMBO No.1806-GS, -GM Series
Maximum servicepressure
Maximum servicetemperature
(℃)Maximum service
pressureMaximum service
temperature(℃)
TOMBO No.1808-GHSeries
Water type fluids 650 Class 2500 800 Class 1500Oil type fluids 650 Class 1500 800 Class 1500Gas type fluids 650 Class 1500 800 Class 600
Composite Filler Vortex Gaskets for High-temperature Applications
VortexTM
Gasket-GS, -GM, -GH TOMBO� No. 1806- GS,-GM, -GH Series
Non-asbestos Vortex gasket for high temperatureservice for which normal GRASEAL Vortex cannotbe used. Combination of mica layers and GRASEALfiller with anti-oxidant prevents oxidation ofGRASEAL at high temperature.We offer a line up of three types GS, GM, and GH,depending on service conditions.
■GS SeriesSuitable for non-oxidizing fluids of 450℃ and above.(Ordinary GRASEAL Vortex gaskets are recommended fortemperatures below 450℃)
When fluids contain oxygen, do not use at temperature of 450℃or higher.
■GM SeriesSuitable for high-temperature conditions over 450℃, andusage conditions where there is decoking.(For temperatures below 450℃, ordinary GRASEALVortex gasket is recommended.)
When the internal fluid is air, do not use at temperatures of 450℃or higher.
■GH SeriesSuitable for high-temperature conditions over 650℃, andusage conditions where there is decoking.(For temperatures below 650℃, Vortex Gaskets-GM isrecommended. For temperatures below 450℃, ordinaryGRASEAL Vortex gasket is recommended.)
When the internal fluid is air, do not use at temperatures of 450℃or higher.
■Service Range
Mica
GRASEAL containing oxidation inhibitor
Mica
GRASEAL containing oxidation inhibitor
Mica
GRASEAL containing oxidation inhibitor
17
VO
RT
EX
GA
SK
ET
S
Fluid Maximum servicetemperature℃
Maximum service pressure
Water type fluids 450 Class 600Oil type fluids 450 Class 600Gas type fluids 450 Class 600Cryogenic –240 11MPatemperature fluids (Min. service temperature)
Fluid Maximum service pressure
Maximum servicetemperature℃
Water type fluids 300 Class 600Oil type fluids 300 Class 600Gas type fluids 300 Class 600Cryogenic –240 11MPatemperature fluids (Min. service temperature)
Expanded Graphite Filler Vortex Gaskets for Low-temperature, Low Seating Stress Service
GRASEALTM
Vortex Gasket L TOMBO� No. 1809 Series
Protruding graphite tape (GRASEAL) is used on thegasket surface to make this gasket suitable forcryogenic applications.
■Features1. Outstanding sealability for cryogenic fluids such as LNG, etc.2. Superb sealability even in low seating stress.
■ApplicationsSuitable for services such as: * Cryogenic lines for LNG, LN2, LO2, LHe, etc.* Locations where adequate seating stress for ordinaryGRASEAL Vortex gasket is not attainable.
■Service RangeTOMBO No. 1839R
Expanded Graphite Filler Vortex Gaskets for use with Aluminum Flanges
GRASEALTM
Vortex Gasket for Aluminum Flanges TOMBO� No. 1809-AL Series
GRASEAL
This GRASEAL Vortex gasket for aluminum flangesuses a combination of aluminum and type 304stainless steel as the hoop material.
■Features1. Suitable for aluminum flanges.2. Outstanding sealability for cryogenic fluids such as
LNG, etc.3. Superb sealability even in low seating stress service.
■ApplicationsSuitable for cryogenic temperature lines such as LNG, LN2,LH2, LHe and aluminum flanges.
■Service RangeTOMBO No. 1839RAL
Aluminum hoop
Stainless steel hoop GRASEAL
JO
INT
SH
EE
TS
Vortex Gaskets for Heat Exchangers
Heat Exchanger VortexTM
Gasket with Pass Ribs
TOMBO No. 1804EX
18
VO
RT
EX
GA
SK
ET
S
Irregular-shape Spiral Wound Gaskets
Irregular-shape VortexTM
GasketThis type of Vortex gasket includes various shapessuch as the normal ovals, track shapes, diamonds,squares, and so on. (Shapes with long straightlines, small curvature radius, etc., are difficult tomanufacture; therefore, please consult with usbefore ordering.)
■ApplicationsMainly used for boiler manholes, hand holes and valvebonnets, etc.
■How to indicate dimensions
Notes: (1) When ordering gaskets, please indicate the dimensions A, B, C,R1, R2 and R3 shown in the diagram. R3 is not necessary withdiamond shapes where R3 is a straight line.
(2) Dimension A for oval and track shapes: Shall be 40mm or over.Dimension A for diamond and square shapes: Shall be 60mm or over.
(3) Ratio A/B shall be 2/3 or over.
A A
R1 R1
R3R2
R1=ー 2A
B B C
C
Track type Oval type
A A
A
R1 R1
R2 R3B
C C
Diamond type Square type
Rib type Rib material and dimensions
This type of Vortex gasket has stainless steel tubeor metal jacketed ribs welded inside the Vortex.NA Vortex, GRASEAL Vortex and NAFLON Vortexare available.
■Features1. Ribs can be manufactured in any shape.2. Ribs can be manufactured with either stainless steel
tube or metal jackets. Sealability is the same.
■ApplicationsUsed for general heat exchangers.
■Rib types (for a gasket thickness of 4.5mm)
Stainless steel tube
Metal jacket
Type 321 stainless steel4.8 (tube diameter)×0.5 wall thickness
TOMBO No. 1841.The metal is the same as that of theVortex hoop.10 (width) × 4.7 (thickness)
Unit: A
19
VO
RT
EX
GA
SK
ET
S
Special Construction Spiral Wound Gaskets
Special Construction VortexTM
GasketInner ring rod typeThis type of Vortex gasket has a metal rod insteadof a regular type inner ring.
■ApplicationsRecommended where the regular type inner ring cannotbe installed.
■Rod dimensions and materials
Gasket thickness
Availablematerials
Wound partThickness Maximum width
4.5 3.2 4.0
Wound-metal hoop typeThis type of Vortex gasket has a 3.2A thick windingmetal hoop instead of the outer metal ring.
■ApplicationsRecommended where outer ring is not wide enough forM&F or T&G flanges. Do not use for raised face (RF)flanges as the mechanical strength of wound metal hoopis less than normal outer metal ring.
■Hoop materials and dimensions
Notes: Basically, only rod type Vortex gaskets with a thickness of 4.5mm or morecan be manufactured.
Gasketthickness Available materialsRod
diameter
4.5 3.2 Type 304,316 stainless steel
Type 304 stainlesssteel, Type 316
stainless steel, otherNotes: In principle,only 4.5A thickness hoop material type Vortex gaskets
can be manufactured.
Unit: A
Unit: A
20
VO
RT
EX
GA
SK
ET
S
Design standard■Gasket, Inner and Outer ring thickness ■Available inner diameters
3.2 2.0 2.04.5(standard) 3.2 3.06.4 4.5 4.0
Inner and outer ring thicknessCarbon steel Other than carbon steel
Gasketthickness
3.2 16 6004.5 16 (3000)6.4 1500 (3000)
Available inner diametersMinimum Maximum
Gasketthickness
Unit: A
■Available widths
16 ~ 30 4.0~10 4.5~ 10 – 2.5 –
31 ~ 46 4.0~15 4.5~ 15 – 2.5 4
47 ~ 55 4.0~20 4.5~ 20 – 3 4
56 ~ 70 4.0~22 4.5~ 25 – 3 4
71 ~ 90 4.0~22 4.5~ 30 – 3.5 4
91 ~ 110 4.5~22 5.0~ 35 – 3.5 4
111 ~ 150 4.5~22 5.0~ 35 – 4 4
151 ~ 170 4.5~22 5.0~ 40 – 4 4.5
171 ~ 200 4.5~20 5.0~ 40 – 4 4.5
201 ~ 300 4.5~20 5.0~ 40 – 4.5 4.5
301 ~ 400 4.5~18 5.0~ 40 – 5 5
401 ~ 500 5.0~18 5.5~ 40 – 5.5 5.5
501 ~ 600 5.5~15 6.0~ 35 – 6 6
601 ~ 700 – 6.5~ 35 – 7 7
701 ~ 800 – 7.0~ 35 – 8 8
801 ~ 900 – 7.5~ 35 – 9 9
901 ~ 1000 – 8.0~ 30 – 10 10
1001 ~ 1100 – 8.5~ 30 – 11 11
1101 ~ 1200 – 9.0~ 30 – 11 12
1201 ~ 1300 – 10.0~ 27[25] – 11 13
1301 ~ 1400 – 11.0~ 27[25] – 11 14
1401 ~ 1500 – 12.0~ 27[25] – 11 15
1501 ~ 1600 – (12)~ 27[25] (12)~30 15 16
1601 ~ 1700 – (12)~ 25[22] (12)~30 15 17
1701 ~ 1800 – (12)~ 25[22] (12)~30 15 18
1801 ~ 1900 – (12)~ 25[22] (12)~30 15 19
1901 ~ 2000 – (12)~ 25[22] (12)~30 20 20
2001 ~ 2100 – (12)~ 22[20] (12)~30 20 20
2101 ~ 2200 – (12)~ 20 (12)~30 20 20
2201 ~ 2300 – (12)~ 20 (12)~25 20 20
2301 ~ 2500 – (12)~ 18 (12)~25 20 20
2501 ~ 2800 – – (12)~22 20 20
2801 ~ 3000 – – (12)~20 20 20
Range for gasket inner diameter Inner diameter of inner ringInner diameter of outer ring
Available gasket widthsMinimum width of
outer ringMinimum width of
inner ringGasket thickness3.2
Gasket thickness4.5
Gasket thickness6.4
Unit: A
Unit: A
*Values in brackets ( ) are for reference.*Dimensions shown in brackets [ ] are for graphite filler and for a combination of a titanium hoop and PTFE filler.*Special configuration Vortex gaskets such as TOMBO No.1809 and 1809AL are available only with a thickness of 4.5A.*Maximum gasket diameter is 1200 mm for TOMBO No. 1809 and 600 mm for TOMBO No. 1809-AL.
Notes: Gaskets with a thickness of 3.2A are mainly used forsmall-diameter valve bonnets and are not used for pipeflanges.
*Please consult with us in case of dimensions over values inbrackets ( ).
21
VO
RT
EX
GA
SK
ET
S
Other Joint Sheets■Recommended gasket widths (for a gasket thickness of 4.5mm)
Notes:(1) The type without an inner ring can be used if the following conditions are fully satisfied.
Filler material : NA paper.
Pressure rating : Class 600 or below, or 40K or below.
Size : Nominal diameter 24B or below, or 600A or below.
■Flange types and suitable gasket types
16
30
100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400
25
20
15
10
5
0
Recommended width
Recommended minimum widths for NA Vortex gaskets.
Recommended minimum widths for GRASEALand NAFLON Vortex gaskets.
Gas
ket
wid
th (A
)
Gasket inner diameter (A)
Full Face (FF)
Raised Face(RF)
Male & Female(M&F)
Tongue & Groove( T&G)
With inner and outer ring (1) With inner and outer ring (1) With inner ring (1) Basic type
22
VO
RT
EX
GA
SK
ET
S
Notes for Designing■Applicable flanges
(1) Since Vortex gaskets require a comparativelyhigh tightening stress, do not use for low-pressure flanges (JIS 2K, 5K, vacuum lines, etc.).
(2) Only TOMBO No. 1809-AL Series Vortex gasketscan be used for aluminum flanges.
■Necessity of inner ringThe function of the inner ring is to prevent thegasket from buckling or damage, to withstand hightightening stress. When installing a gasket on aflange with no means of restraining support towardthe inside, inner ring types should always be used inthe following cases:(1) With a low friction filler such as GRASEAL and
NAFLON.(2) When the pressure rating of the flange is
class900 (63k) or above.(3) When the nominal diameter of the flange is 650A
(26B) or above.
■Clearance for grooved flanges(1) Tongue & Groove (T&G) and Male & Female
(M&F) flange
(2) Flat to Groove flangeClearance (b) differs depending on the seatingstress of the gasket.Please consult us for designing the clearance.
■Gasket thickness and suitable groovedepth(1) Tongue & Groove (T&G) and Male & Female
(M&F) flange
(2) Flat to Groove flange
■Flange surface finish
Buckling of Vortex gasket
Buckling
Application for Tongue & Groove (T&G) flange
f
a b
Application for Flat to Groove flange
f
a b
*Please consult us for applications of 6.4t thickness Vortexgaskets to Flat to Groove flange.
Gasket diameterAppropriate clearance
(a) (b)250 or below 0.5 0.5251~630 0.7 0.7631~1600 1.0 1.01601 or above 1.5 1.5
Unit: A
Gasket thickness Suitable groove depth (f)3.2 3.5 or more4.5 5.0 or more6.4 7.0 or more
Unit: A
Gasket thickness Suitable groove depth (f)3.2 2.4 4.5 3.26.4 –
Fluid type Recommended surface finishLiquid type 6.3 RaGas type 3.2 Ra
Unit: A
+0.1-0
+0.1-0
23
VO
RT
EX
GA
SK
ET
S
■Bolt materialsSince Vortex gasket require comparatively hightightening stress, high tension bolt such as SNB 7 orover is recommended for bolt specification.
¡TighteningTo obtain uniform seating stress, apply the tighteningload (torque) in 4 - 5 stages, proceeding diagonally asshown in the diagram below. Gradually increase thestrength of the tightening load until the prescribedseating stress is obtained. After that further tighten byproceeding clockwise 1 - 2 turns.
¡Basic-type VortexBasic-type Vortex gaskets (including irregular-typegaskets) should be carefully handled as theydeform easily with even with slight external force.Even if gaskets are somewhat deformed, they maystill be fitted into the groove on the flange andused, depending on the condition of the gasket. Insuch cases, please consult with us.
■Gasket seating stress(1) For general liquids :
The calculation results Wm1 and Wm2, stipulated inJIS B 8265, etc., shall be calculated using m and y.The largest stress obtained from the calculation shallbe the required seating stress.
(2) For fluids that tend to leak:For gas type fluids, leakage may occur if only seatingstress calculated by JIS B8265,etc. is applied.In addition to Wm1 and Wm2, the seating stress(Wm3) shall also be calculated in accordance with thefollowing σ3 per unit of gasket contact surface. Thelargest stress from the calculation shall be used as therequired seating stress.
■Seating stress of gasket
Cautions¡Storage
1. Store gaskets indoors in a cool, dark place in theoriginal wrapping.
2. Do not stand gaskets upright or hang them.3. Do not bend, twist, push or press gaskets.
¡Installation1. Before installing a gasket, first clean the surface of the
flange and check the surface is free of foreign matters,scratches, etc.
2. Do not handle gaskets roughly. Since large diametergasket is easily damaged (dropping off of windings), itshould be handled very carefully by several persons.
3. Place gaskets carefully in correct position.4. In principle, there is no need to apply gasket paste.
But, if considered necessary NAFLON paste (TOMBONo. 9400) is recommended for temperature conditionsof 300℃ or lower,
5. Do not re-use gaskets.
Bolt tightening sequence
1
7
4
6 2
8
3
5
Gasket typeGasket factor
m(1)Minimum design seating stress
y(2)N/E
Minimum seating stress (for gas sealing)(3)
σ3
N/E
TOMBO No.1804-GR SeriesTOMBO No.1804-NA SeriesTOMBO No.9090 SeriesTOMBO No. 1806 -GS -GM -GH
TOMBO No.1809 Series
39.2 78.468.939.2 78.4
29.4 (Class 150)58.8 39.2 (Class 300)
49.0 (Class 600)
3.00
notes:(1),(2) Specified by JIS B 2205 (1991), JIS B (1995) and JPI-7S-81-96.(3) Specified by test results from NICHIAS Corporation
24
VO
RT
EX
GA
SK
ET
S
■Compression recovery curve
Gasket ; TOMBO No.1834-NASize 3B ; ø101 x ø117 x ø148 x 4.5t 8B ; ø236 x ø260 x ø307 x 4.5t
79
59
39
20
04.6 4.4 4.2 4.0 3.8 3.6 3.4 3.2
Co
mp
ress
ion
load
(N
/E)
Gasket thickness (A)
●TOMBO� No.1834-NA (4.5t) compression recovery
Class 300 x 3B
Class 300 x 8B
137
98
118
79
59
39
20
04.44.6 4.2 4.0 3.8 3.6 3.4 3.2
Co
mp
ress
ion
load
(N
/E)
Gasket thickness (A)
●TOMBO� No.1834R-GR(4.5t)compression recovery
Class 600 x 8B
Class 300 x 8B
25
VO
RT
EX
GA
SK
ET
S
137
98
118
79
59
39
20
04.6 4.4 4.2 4.0 3.8 3.6 3.4
Co
mp
ress
ion
load
(N
/E)
Gasket thickness (A)
Gasket ; TOMBO No.1839RSize 8B ;ø220 x ø236 x ø260 x ø307 x 4.5t (Class 300) ø209 x ø230 x ø260 x ø320 x 4.5t (Class 600)
●TOMBO� No.1839R (4.5t) compression recovery
Class 600 x 8B
Class 300 x 8B
137
98
118
79
59
39
20
04.4 4.2 4.0 3.8 3.6 3.4 3.2
Co
mp
ress
ion
load
(N
/E)
Gasket thickness (A)
Size 8B ;ø220 x ø236 x ø260 x ø307(Class 300)Size 8B ;ø209 x ø230 x ø260 x ø320(Class 600)
●TOMBO� No.1839R-AL(4.5t)compression recovery
Class 600 x 8B
Class 300 x 8B
26
VO
RT
EX
GA
SK
ET
S
Selection Guide¡Water type fluids
Design Points¡Oil type fluids
Class2500
Class1500
Class900
Class600
Class400
Class300
Class150
50
20
10
5
2
1
0.5
0.2
0.1
0-200 -100 0 100 200 300 400 500 600 700 900800 1000
150
2500
1500
900
600
400
300
GR1
GR1
GR1
NA2
PTFE3NA2
GS1
GS1
Class2500
Class1500
Class900
Class600
Class400
Class300
Class150
50
20
10
5
2
1
0.5
0.2
0.1
0-200 -100 0 100 200 300 400 500 600 700 900800 1000
150
2500
1500
900
600
400
300
GR1
GR1
GR1
NA2
PTFE3
GS1
GS1
GM2
GH1
GM2NA2
Class2500
Class1500
Class900
Class600
Class400
Class300
Class150
50
20
10
5
2
1
0.5
0.2
0.1
0-200 -100 0 100 200 300 400 500 600 700 900800 1000
150
2500
1500
900
600
400
300
GR1
GS1
GR1
GR1
GR1PTFE2
GR1
GS1
GM2
GH1
GH3
PTFE2
NA3
GM2
NA2
Class2500
Class1500
Class900
Class600
Class400
Class300
Class150
50
20
10
5
2
1
0.5
0.2
0.1
0-200 -100 0 100 200 300 400 500 600 700 900800 1000
150
2500
1500
900
600
400
300
PTFE1
PTFE1
GR1
GR1
GR1
GR2
GR2
Pre
ssu
re (
MP
a)
Temperature (℃)
Pre
ssu
re (
MP
a)
Temperature (℃)
Pre
ssu
re (
MP
a)
Temperature (℃)
Pre
ssu
re (
MP
a)
Temperature (℃)
Selection Guide¡Gas type fluids
Design Points¡Corrosive fluids
27
VO
RT
EX
GA
SK
ET
S
Design Points■Selection chart
1. The following codes indicate the gasket types:
2. When several recommended gaskets areindicated by the line connecting temperature andpressure, the priority is indicated by numericalorder.
3. This table is just a general selection guide.
■Service temperature for hoop material
■Service temperature for inner and outer rings
■Applicable fluidsPay special attention when selecting Vortex gasketsfor the following fluids.1. Combustion promoting gas (oxygen):
Use only NAFLON Vortex OX type (TOMBO No.9090-OX etc.) which contains no oil in its fillermaterial. Other types of Vortex gasket should notbe used since their fillers contain combustiblematerials.
2. Strong acid fluids:Do not use GRASEAL Vortex gaskets for strongoxidizing acids such as nitric acid and nitrates.For details, refer to fluids that cannot be usedwith GRASEAL on page 41.
3. High temperature fluids:Select materials for the hoop and inner ring thatcan sufficiently withstand usage conditions.Do not use Vortex Gasket-GS at temperatures of450℃ or above if fluids contain oxygen. If theoxidative power of the fluids is weak, VortexGasket-GM, -GH can be used.
4. Corrosive fluids:Select hoop and inner ring materials that arefully capable of withstanding the serviceconditions.
5. Acidic fluids:Do not use NA Vortex gaskets.
Code Product TOMBO No.GR GRASEAL Vortex 1804-GR SeriesNA NA Vortex 1804-NA SeriesPTFE NAFLON Vortex 9090 SeriesGS GRASEAL Vortex-GS 1806-GS SeriesGM GRASEAL Vortex-GM 1806-GM SeriesGH GRASEAL Vortex-GH 1808-GH Series
Type Materialcode Old material code Recommended service
temperature(℃)
304 Stainless Steel E 304 500 and below304L Stainless Steel L 304L 500 and below316 Stainless Steel G 316 600 and below316L Stainless Steel H 316L 600 and below321 Stainless Steel J 321 750 and below347 Stainless Steel K 347 750 and belowInconel 600 Y IN 800 and belowMonel M M 750 and belowTitanium T TI 500 and below
Type Materialcode
(Remarks) Oldmaterial code
Recommended servicetemperature(℃)
Carbon steel S SS –29 ~ 425304 Stainless Steel E 304 600 and below316 Stainless Steel G 316 600 and below*The temperatures are of inner and outer rings, not of fluids.
28
VO
RT
EX
GA
SK
ET
S
For orderingPlease specify the following items when ordering Vortex gaskets:1. Type (basic, with inner ring, with outer ring, with
inner and outer rings)2. Special construction (with rib, metal rod, winding
metal hoop, etc.)3. Materials (filler, hoop, inner ring, outer ring)
■Indications
4. Dimensions(1) Standard size: Applicable standards such as JIS,
JPI, ASME, etc., nominal pressure/ class,nominal diameter.
(2) Non-standard size: service pressure, dimensions(inner diameter of inner ring, gasket innerdiameter, gasket outer diameter, outer diameterof outer ring, thickness).
5. Special treatment (OX), Special specifications
Type Materialcode Old material code
Carbon steel S SS304 Stainless Steel E 304304L Stainless Steel L 304L309S+Cb Stainless Steel W 309S+CB316 Stainless Steel G 316
Type Materialcode
Old materialcode
316L Stainless Steel H 316L316ELC Stainless Steel X 316ELC321 Stainless Steel J 321347 Stainless Steel K 347410 Stainless Steel R 410
Type Materialcode
Old materialcode
430 Stainless steel U 430Inconel 600 Y INMonel M MTitanium T TIOthers Z -
■Hoop, inner ring, outer ring material codes
[GRASEALTM VortexTM, NA VortexTM, Others]18□□□□□─□□─□□□─□
Yes
No
3
0
YesNo
EX
None
Yes See table belowNo
YesO
O
See table belowNo
Yes
No
R
None
Outer ring ●
304 Stainless steel316 Stainless steelOthers
4
68
Hoop material(1) ●
Rib ●
Inner ring ●
● Special specifications
● Outer ring/Material
● Inner ring/Material
● Hoop material (See table below)
GRNAGSGMGH
● Filler materialGraseal NA Paper GS(2) GM(2) GH(2)
Note:(2) See page 16
When special specification is agreed with end user, this code will be added
Note:(1) Even if hoop material is either 304 or 316 stainless steel, code will be "8" when inner or outer ring material is "Others".
*In the case of "others" please indicate the specific material
*If any of the hoops, inner rings and outer rings contain any "other" material, the material codes of hoops, innerrings and outer rings must all be prefixed by "Z" and the specific material name should be indicated.
*Some of the hoop and ring materials shown in this table may not be available as ready stock material. For details,please consult us.
29
VO
RT
EX
GA
SK
ET
S
TOMBO No. Type Filler Hoop Inner ring Outer ringMaterials Old
TOMBO No.
1806-GR-GOO Basic Expanded graphite 316 Stainless Steel None None 1806-GR1834-NA-EOS With outer ring NA paper 304 Stainless Steel None Carbon steel 1834-NA-SS9090-IOR-TTG With inner and outer rings PTFE Titanium Titanium 316 Stainless Steel 9090-IOR-TI-TI-316
■Examples of numbering
[GRASEALTM VortexTM L]
18□9□□□─□□□─□
Yes
No
3
0
Stainless steelAluminum
None
AL
YesO
See table on previous page
No
Only required when so decided through agreement with the user.
Yes See table on previous pageONo
Yes
No
R
None
Outer ring ●
Application (flange material) ●
Inner ring ●
● Special specifications
● Outer ring/Material
● Inner ring/Material
● Hoop material (See table on previous page)
[NAFLONTM VortexTM]9090─□□□□□─□□□□□─□
Basic type
With inner ring
None
IRWith outer ring ORWith inner and outer rings IOR
Yes See table on previous pageNo
Only required when so decided through agreement with the user.
Yes See table on previous page
0
0No
Inner ring and Outer ring ● ● Special specifications
● Outer ring/Material.
Standard product NoneOXFor oxygen
● Special processing
● Inner ring/Material
● Hoop material (See table on previous page)
Yes
No
EX
None
Ribs ●
30
ME
TA
L G
AS
KE
TS
Cross section
Metal gaskets are suitable for high pressure andhigh temperature duties instead of soft gasket.Metal gaskets can be produced in any suitablematerials such as soft iron, stainless steel, brass,aluminum, titanium, special alloy, etc.Plain and serrated metal gaskets can be used withflat surface flanges, but other metal gasketsshould be installed to specified flanges.
■Applications : Pipe flanges, valves, pressure vessels,heat exchangers, etc.
Metal Solid Gaskets
Plain Metal Gasket TOMBO� No.1850P
■Features : Flat metal gaskets are either cut or machinedfrom flat plates, round rods, forging metals, etc. A higherseating stress is required than with other types ofgaskets. In order to improve sealability, a V-groove ornubbin may be machined on the flange.
TOMBO No.1850P-E
Cross section
Metal Solid Gaskets
Serrated Metal Gasket TOMBO� No.1890
■Features : Serrated Metal Gaskets with V-grooves aroundflat type metal gaskets to form a serrated cross section asshown in the diagram.Inner and/or outer ring types also available.This gasket is used for high-pressure pipe flanges, vesselsand valves.Expanded graphite sheets can also be adhered to bothsurfaces upon request.
TOMBO No.1890-E
*For Grooved Metal Gasket with covering layers, please refer to technicaldata available separately.
■Applications : Pipe flanges, valves,pressure vessels, heat exchangers, etc.
■Applications : Pipe flanges, valves,pressure vessels, heat exchangers, etc.
■METAL GASKETS
31
ME
TA
L G
AS
KE
TS
Metal Solid Gaskets
Octagonal Ring Joint Gasket TOMBO� No.1850C
■Features : These gaskets are processed to solid ringjoints with an octagonal cross section.Used for high-pressure pipe flanges, vessels and valves.
■Standard dimensions : Please refer to the table of dimensions at the end.
■Applicable standardsJPI-7S-23ASME B16.20API Spec 6A
TOMBO No.1850C-L
TOMBO No.1850V-G
Metal Solid Gaskets
Oval Ring Joint Gasket TOMBO� No.1850V
Cross section
■Features : These gaskets are processed to solid ringjoints with an oval cross section. Like the octagonal type,this type is used for high-pressure pipe flanges, vesselsand valves. The re-use of ring joint gasket is notrecommended.
■Standard dimensions : Please refer to the table of dimensions at the end.
■Applicable standardsJPI-7S-23ASME B16.20
Cross section
■Applications : Pipe flanges, valves,pressure vessels, heat exchangers, etc.
■Applications : Pipe flanges, valves,pressure vessels, heat exchangers, etc.
32
ME
TA
L G
AS
KE
TS
■Metal material types, material codes, hardness and maximum service temperature
TOMBO No. Product name Cross section Features
1850-RX
1850-BX
1850-D
1850-L
1850-O
1850
1850
■Other Metal Solid Gaskets
RX ringgasket
This ring joint gasket is suited for flanges in accordance with APIspec 6A, model 6B.
This ring joint gasket is suited only for flanges in accordance withAPI spec 6A, model 6BX.
This delta gasket is designed to be self energized by the internalsystem pressure.
The sealing action is based on line contact sealing. Dimensions inaccordance with DIN 2696
A solid metal o-ring.
A self sealing type metal gasket with a cross section as shown.
This bridgeman gasket is a pressure-activated gasket. Use for seal ring.
BX ringgasket
Delta gasket
Lens typegasket
MetalO-ring
Doble corngasket
Bridgemangasket
Gasket materials(1) Main composition(2) RemarksMaximum service
temperature(℃)
Materialcode
Old materialcode
Maximum hardness(3)
Soft iron - D D 90 - 538 C≦0.05%Carbon steel - S(4) SS 120 - 5385Cr - 0.5Mo steel 5Cr-0.5Mo F F5 130 - 649 ASTM A182 F513Cr steel 13Cr R 410 170 - 704Type 304 stainless steel 18Cr-8Ni E 304 160 - 816Type 304L stainless steel 18Cr-8Ni, LC L 304L 150 - 816Type 316 stainless steel 16Cr-12Ni-2Mo G 316 160 - 816Type 316L stainless steel 16Cr-12Ni-2Mo, LC H 316L 150 - 816Type 321 stainless steel 18Cr-10Ni-Ti J 321 160 - 816Type 347 stainless steel 18Cr-10Ni-Nb K 347 160 - 816Aluminum - A Al - 40 300Copper - C Cu - 80 400Monel - M M 130 - 800Nickel - N Ni 120 - 760Titanium - T Ti 140 - 800
Notes: (1) Materials should be selected with regard to operating temperature and chemical compatibility. Other metal materials are availableupon request.
(2) The alloy ingredients, etc., are indicated.
(3) Hardness of materials to be used for TOMBO No. 1850-P and 1890 may differ from this table. For details, please consult us.
(4) In the case of rolled steel plain metal gaskets, SS is employed.
HB HV
33
ME
TA
L G
AS
KE
TS
Blinds and Spacers, and Spectacle BlindsThese blinds and spacers are used to shut offpiping and to cut off pressure during sealing testsand pressure tests. Solid spectacle blinds andbuilt-in ring joint gaskets are also available. Pleaseindicate the material, dimensions and so on.
■Types and shapes
■Indications
18□0□─□
Serrated type
Other
9
5
Octagonal type COval typeRX typeBX type Delta typeLens typePlain typeSerrated typeOther
VRXBXDLP
NoneNone
Shape ●
Shape ●
● Material code
Type
Top view(RF Type)
Side view(RF Type)
Side view(RTJ Type)
Blinds Spacers Spectacle blinds
34
ME
TA
L G
AS
KE
TS
Hollow Metal Rings
Metal O-Seal TOMBO� No. 9200
Stainless steel or Inconel tubes are formed into an O-ringshape, the ends are welded together, and then surfaces arefinished ultra-smooth.PTFE coating or silver plating is used on the surfaces forsealing gases, vacuum and highly volatile liquids.Highly reliable sealing performance is provided over a widerange from high temperatures to cryogenic temperatures, andfrom high pressures to vacuum.This gasket features a compact design that requires acomparatively low seating stress and requires little space.
■ApplicationsValve bonnets, high-pressure vessel flanges, equipmentjoints, pipe flanges, plastic processing machinery, rubberextruders, hydraulic equipment, pneumatic equipment,vacuum vessels, nuclear power containers, aircraftengines, rocket engines and automobile engines.
■TypeS
■Materials and service temperature
■Service rangeHigh-pressure water Up to 400MPa High pressure gas Up to 300MPa Vacuum Up to 10-4Pa
TOMBO No.
9200P
9200V
Standard type MetalO-Seal
Vent hole type MetalO-Seal
A standard type Metal O-Seal can be applied fromvacuum to about7.0MPa.
Two or more holes are provided on the inside (for internalpressure) or outside (for external pressure) of the ring so thatthe fluid will enter the ring and increase self-sealing performance.Suitable for high-pressure sealing for 7.0MPa and over.
Product name Shape Features
Tube material
Surfacetreatment
Type 321 stainless steel J 321 –250 ~ 500(1)
Inconel 600 Y In –250 ~ 700(1)
PTFE coating TF TFE –250 ~ 250Silver plating AG Ag –(2)
PTFE coating or silver plating is applied for gas sealing,vacuums and highly volatile liquids.
Surface treatment thickness is 0.03A~0.05A.
Material Old code Service temperature range℃Code Reference
Notes: (1) The maximum service temperature is 250℃ with PTFE coating.
(2) The service temperature range of silver plating is the same as type without silver plating.
■Indications
9200□─□□□
PStandard typeVent hole type V
Type 321 stainless steelInconel 600
JY
Shape ● ● Surface treatment material
● Tube material
NoneAGTF
NoneSilver platingNAFLON coating
35
ME
TA
L G
AS
KE
TS
■Standard dimensions
6.3S
W
H
A
I D
R
Internal pressure sealing type External pressure sealing type
H6.3S
WR
A
O D
Tube cross section diameter Wall thickness(3) Outside diameter (A) Compression load(4)
(A) (A) Recommended range Available dimensions N/A0.8 0.15* 6(5)~25 6(5)~30 69
1.6 0.25 – 10~200 1180.36* 15~50 11~200 284
2.4 0.25 – 40~500 590.46* 40~200 20~500 2350.25 – 60~1500(6) 49
3.2 0.35 – 60~1500(6) 880.50* 65~700 50~1500(6) 177
4.8 0.50(7) – 150~1500(6) 690.80* 500~1200(6) 150~1500(6) 333
6.4 0.80* 1000~1500(6) 250~1500(6)(8) 177Notes: (3) Standard wall thickness is indicated with asterisks *. Apply the standard wall thickness for gases.
(4) Indicates the load required to obtain proper seating stress. To obtain the actual seating stress, add the end force to becalculated to the above.
(5) The minimum outside diameter for the vent hole type is 10A.
(6) The maximum outside diameter for PTFE coating is 1300A; for silver plating, the maximum outside diameter is 1100A.
(7) A tube diameter of 4.8A with a wall thickness of 0.50A is only available with type 321 stainless steel.
(8) Please consult with us if gasket diameter is larger than 1500A.
■Standard groove dimensions
Tube cross section diameter Groove outside diameter Groove inside diameter Groove width (W)(10)
Groove depth(H)(10) Groove corner(R)(O.D.) for internal pressure sealing (I.D.) for external pressure sealing(10)(11) Maximum
Notes: ( 9) The groove surface finish is 0.8a (3.2S) for gas and vacuum sealing, and 1.6a (6.3S) for all other cases.
(10) The groove dimensions shall be revised as follows when PTFE coating or silver plating are applied:
Internal pressure sealing: 0.1A shall be added to the groove outside diameter (O.D.), groove width (W) and groove depth (H).
External pressure sealing: 0.1A shall be subtracted from the groove inside diameter (I.D.), and 0.1A shall be added tothe groove width (W) and groove depth (H).
(11) A indicates the gasket outside diameter.
Recommended Minimum
0.8
1.6
2.4
3.2
4.8
6.4
1.2
2.4
3.6
4.8
7.2
9.6
1.1
2.0
2.9
3.7
5.6
7.5
0.2
0.3
0.5
0.8
0.8
0.8
0.60±0.05
1.15±0.05
1.75±0.05
2.55±0.05
3.75±0.05
5.00±0.05
A+0.35+0.25 (A-1.6)-0.25
-0.35
(A-3.2)-0.30-0.40
(A-4.8)-0.30-0.40
(A-6.4)-0.35-0.50
(A-9.6)-0.35-0.50
(A-12.8)-0.40-0.55
A+0.40+0.30
A+0.40+0.30
A+0.50+0.35
A+0.50+0.35
A+0.55+0.40
Unit: A
Corrugated Metal Gaskets Bonded with Expanded Graphite
CMGCTM
Gasket TOMBO� No.1880-GR
Expanded graphite sheet (GRASEAL sheet) is adheredon both sides of concentric corrugated steel plate (Type316L stainless steel).
■Features¡Excellent sealing performance that remains nearly the same
under both low and high temperatures (up to 400℃)¡Can be used for almost all fluids, with the exception of strong
oxidizing acid.¡This type of gasket is used widely by major foreignl oil
companies.
■Applications¡Gasket for piping flange used with fluids such as petroleum, etc.¡Alternative to conventional asbestos joint sheets
■Standard dimensions¡ASME (JPI) specifications
Class 150 1/2B to 24B*Please consult with us if the required sizes are outside of the
above range.¡Nominal thickness : 1.6mm
■Service range¡Service temperature : –240℃ to 400℃¡Maximum service pressure : 5.2MPa
■Recommended parameters for fastening¡Gasket factor "m" : 2.0 (-)¡Minimum design seating stress "y" : 26.0 (N/mm2) ¡Minimum seating stress for gas sealingσ3(gas) : *39.2 (N/mm2)*Specified by test results from NICHIAS Corporation
■Structure¡Sheets of expanded graphite are pressure-bonded
onto both sides of a corrugated Type SUS316Lstainless steel.
36
ME
TA
L JA
CK
ET
ED
GA
SK
ET
S
Fluids not suitable for use with GRASEAL
Classification Name of liquid
Oxidizing acid Nitric acid, Concentrated sulfuric acid, Hot sulfuricacid, Chromic acid, Mixed acids, etc.
Oxidized salt Nitrates, Chlorates, Hypochlorites, etc.Halogen compounds Bromine, Fluoride, Iodine, Chlorine dioxide, etc.Combustion promoting gas Oxygen (Pure oxygen)
Nominal thickness 1.6mm
Expanded graphite sheet
Type SUS316L stainless steel plate
Expanded graphite sheet
Type SUS316 stainlesssteel plate
Sectional pattern diagram
37
ME
TA
L JAC
KE
TE
DG
AS
KE
TS
A highly heat resistant core is completely covered with a thin
metal jacket.
Double jacket type as per diagram below is standard, but
other jacketing methods are also available.
These gaskets are used for heat exchangers, pressure vessels,
tanks, equipment, valves, high-temperature joint flanges, and
so on.
■Types
■Metal types and available dimensions
1841
1841-Fi
1861
1861-Fi
3.0
3.0
3.0
3.0
Non-asbestos millboard
Ceramic fiber felt
Non-asbestos millboard
Ceramic fiber felt
NA Metal Jacketed Gasket
NA Metal Jacketed Gasket forHigh-temperature applications
NA Corrugated Metal JacketedGasket
NA Corrugated Metal Jacketed Gasketfor High-temperature applications
530
1300
530
1300
Maximum servicepressure
MPa
Maximum servicetemperature(2)
℃
Standardthickness
ACore materialProduct name Cross section (1)TOMBO No.
6.0
Notes: (1) Other types of gaskets with different cross section are also available upon request.
(2) Indicates the heat resistance of the core. The values may become lower, depending on the jacket metal material.
18□1─□□─□─□□
4FlatCorrugated 6
NA mill boardCeramic fiber felt
NoneFi
● Surface material
● Core material
● Jacket metal material code
NoneGR
NoneGraseal
Shape ●
Old Maximum service temperature Maximum dimensions (4)Metal type (3) Material code
material code ℃ A
Carbon steel S SS 535 1480Type 304 stainless steel E 304 800 1180Type 316 stainless steel G 316 800 1180Type 310S stainless steel V 310S 1150 1180Aluminum A Al 400 980Copper C Cu 400 1180Monel M M 800 890
Notes: (3) Other metal materials are also available upon request.
(4) Indicates the maximum diameter that can be fabricated in one piece without welding. For larger sizes, welded types are also available.
■Applicable standardsASME B16.20 Jacketed Gaskets
■METAL JACKETED GASKETS
Cautions(1) The use of expanded graphite tape (TOMBO No. 1220 or TOMBO No. 1221) on the sealing surface is
recommended for more reliable sealing performance at temperatures of 400℃ and below. High-temperature gasket paste (Never Seize® nickel special grade) is recommended at temperatures higher than400℃.
(2) Metal Jacket Gaskets are not recommended for standard pipe flanges because it is difficult to obtainenough seating stress. However, if used even so, gaskets with hangers are recommended for centering.
■Indications
38
ME
TA
L JA
CK
ET
ED
GA
SK
ET
S
Metal Jacketed Gaskets with GRASEALTM
TapeExpanded graphite tape is adhered to the surfaceof gaskets.When ordering, please add the code of "GR" to theend of products number as an indication ofsurface material.
Heat Exchanger Gasket
We manufacture gaskets for heat exchangers invarious shapes. Please specify gasket shapes anddimensions based on the drawings and codesshown on the next page.The folded face of the gasket should touch thebottom of the groove on the flange.If the gasket is installed upside-down, the gasketmay not fit with the partition or the sealingperformance of the gasket may decrease.
■Standards for designing dimensionsFor flat gaskets (TOMBO No. 1841, etc.)1. The rib width (W) must be 7A or over.2. The corner radius (R) must be 8A or over.
For corrugated type gaskets (TOMBO No. 1861, etc.)1. The gasket width (N) must be 15A or over.2. The rib width (W) must be 7A or over. (Ribs cannot be
provided with corrugation.)3. The corner radius (R) must be 8A or over.
Section A-A'
A
A'
Welded construction
Filler material
Metal jacket
In some cases, gasket may be supplied with welded passribs. (Please refer sketch below.)Welded pass rib does not affect sealing performance.
39
ME
TA
L JAC
KE
TE
DG
AS
KE
TS
Side A
[HE1]
[HE26]
[HE21]
[HE16]
[HE11]
[HE6]
[HE5]
[HE25]
[HE20]
[HE15]
[HE10]
[HE4]
[HE24]
[HE19]
[HE14]
[HE9]
[HE3]
[HE28]
[HE23]
[HE18]
[HE13]
[HE8]
[HE2]
[HE27]
[HE22]
[HE17]
[HE12]
[HE7]
R R P P P
PP
P
PP
PP
PP
PP
PP
PP
PP
PP
P
PP
P
PP
PP P P
P P PP
P P
PP
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1P1
P P
PPP P
PP
P1
P1
P1
P1
P1
P1
P1
P
R
R
R R
R
R
R
R R
R R R
R R
R R R
R
R
R R R R
R
R
R R
R
R
R
R R R
R R R R R R
R
R R
R
R
R
R
R R
R R
R
R
R R
R R R
R R
R R R
R R
R
R
R R
R R R
R
R
R
R
R
R R
R R
R R
R R
R
R
R R R R
R
R
R
R
R
R
R
R
R
R
R
W W
W
W
W
W
W
W
W
W
W
W
W
W
W W
W
R
W
W
W
W
W
W
W
W
W W
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
O.D.I.D.
t
Heat Exchanger Gasket Standard Shape CodesPlease indicate the shape code and dimensions when ordering.This shape is top view from Side A of right diagram.
■Heat Exchanger Gasket Standard Shape Codes
40
GR
AS
EA
L G
AS
KE
TS
■GRASEALTM
GASKETSExpanded graphite (GRASEAL) is a material processed from pure natural graphite by
chemical treatment and heat treatment at more than 1000℃. This material provides
outstanding heat and chemical resistance, and is excellent for gaskets with high
flexibility and low creep.
Expanded Graphite Gaskets
GRASEALTM
Gasket TOMBO� No.1200/1210/1215
GRASEAL gaskets are cut from GRASEAL sheetsor GRASEAL sheets with metal reinforcement.There are four types in accordance with theapplication.
¡TOMBO No. 1200 GRASEAL GasketCut gasket from expanded graphite sheet (GRASEALsheets) to be used for pipe flanges and valve bonnets,etc. This type is only recommended for small diametergaskets due to its low mechanical strength.
¡TOMBO No. 1210-A GRASEAL Gasket MI-AType 316 stainless steel sheet (0.1 mm thick) with hooksis sandwiched with GRASEAL sheets and then cut intospecific sizes. Mechanical strength is high. As hookheight is low, less damege (such as scrathing etc) toflanges.
¡TOMBO No. 1215 GRASEAL Gasket PMGRASEAL sheets are adhered to both sides of type 304stainless steel sheet of 0.2 A thick. High in mechanicalstrength and easy to handle. As it can also be cut intocomplicated shapes, this type of gasket is widely usedin various industries.
¡TOMBO No. 1215-A Grsaseal gasket PM-AThe stainless steel sheet use in TOMBO No. 1215 hasbeen changed to SUS316 steel (50 micron).
■ApplicationsFor piping flanges, heat exchangers, valve bonnets, etc.,in various industries and for special shape flanges forliquid level gauges.
■Applicable standards¡JPI-7S-79 Expanded Graphite Sheet Gaskets for
Petroleum industry¡JIS F 7102 (TOMBO No. 1215 only)
■Standard size
TOMBO No. 1200
Cautions1. Since TOMBO No.1200 gaskets are fragile, they
are not recommended for narrow width gasketsor large-diameter gaskets. They are onlyrecommended for nominal size of 4 inches orless.
2. The surfaces of GRASEAL Gaskets are easilydamaged, which can result in leakage;therefore, handle with care.
3. Due to its nature, a very small amount ofleakage is inevitable. When very high level ofgas sealing is required, use TOMBO No.1215-T,1215-AT which feature non-permeationtreatment. (maximum service temp. 260℃)
4. In general, GRASEAL Gaskets cannot be usedwith the fluids listed in the table on page 41.
5. When handling TOMBO No.1210-A/ 1215/ 1215-A gaskets, pay attention not to scratchyour fingers on the metal reinforcement.
■Features1. Sealability remains almost same throughout a range of
cryogenic to high temperature (400℃).2. Excellent chemical resistance to almost all liquids other
than strong oxidizing acids, etc.3. Since cold flow and creep property are minor, it is not
affected by over-tightening of gasket.
Type Nominal thickness Maximum outerdiameter (O.D.)
TOMBO No.1200 0.4(0.38) 0.8(0.76) 1.6(1.52) – 3.2(3.04) ø600TOMBO No.1210-A – – 1.5(1.50) 2.0(2.00) 3.0(3.00) ø1480TOMBO No.1215 – 0.8(0.86) 1.6(1.62) – 3.2(3.14) ø580
TOMBO No.1215-A – 0.8(0.81) – – – ø980– – 1.6(1.57) – 3.0(3.00) ø1480
Unit: A(values in brackets are actual thickness)
41
GR
AS
EA
L GA
SK
ET
S
Gasket cross section
Maximum service pressure MPa 3.0 5.2 5.2 5.2 3.0Service temperature Non-oxidizing atmosphere℃ –240~1650 –240~800 –240~800 –240~800 –240~800
Oxidizing atmosphere℃ –240~ 400 –240~400 –240~400 –240~400 –240~400Gasket coefficient m 2.00 2.00 2.00 2.00 ─Minimum design seating stress y N/E 26.0 29.4 29.4 29.4 ─Recommended seating stress forgas sealing. N/E 49.0 49.0 49.0 49.0 49.0
Expanding Graphite Gaskets
GRASEALTM
Gasket Tape TOMBO� No.1220/1221
GRASEAL gasket tape is a self-adhesive tape witha peel off backing and it can easily be installed toall dimensions and shapes. Two different types areavailable for different applications.
¡TOMBO No. 1220 GRASEAL Gasket Tape (Plain)The surface of this GRASEAL Gasket Tape is smooth.The 0.25mm thick type is suitable for flanges with largediameters of 18 inches or over.
¡TOMBO No. 1221 GRASEAL Gasket Tape (Crinkled)This crinkle processed GRASEAL Gasket Tape is suitablefor flanges with a diameter of about 16 inches or less.
■Applications 1. Use as a free-size gasket by applying directly to the
flange surface.2. Improving sealability of metal gaskets (TOMBO No.1840,
1850 etc.) by applying this tape on the sealing surfacewhen seating stress is not adequate.
3. Plain tape with a thickness of 0.13A can be used as atape sealant for high-pressure threaded joints up to300℃.
CautionsDo not use together with soft gaskets such as jointsheets.
TOMBO No.1220
■Standard sizesType Thickness(A) Width(A) Length(mtr)
0.13 12.7 7.6TOMBO No.1220 0.25 12.7 7.6
0.25 25.4 15.20.38 12.7 7.2TOMBO No.12210.38 25.4 14.2
Stainless steel plate(SUS 316 100μ)
Stainless steel plate(SUS 304 100μ)
Stainless steel plate(SUS 316 50μ)
Double-sided tape
Double-sided tape
■Service range and design standards
TOMBO No. 1200GRASEAL Gasket
TOMBO No. 1210-AGRASEAL Gasket MI-A
TOMBO No. 1215GRASEAL Gasket PM
TOMBO No. 1215-AGRASEAL gasket PM-A
TOMBO No. 1220,1221
GRASEAL Gasket Tape
Type
Item
■Not applicableType Fluid name
Oxidizing acids Nitric acid, concentrated sulphuric acid, hot sulphuric acid, mixed acids, chromic acid,etc.
Oxidizing salts Nitrate, chlorate, hypochlorite, etc.Halogen compounds Bromine, fluorine, iodine, chlorine dioxide, etc.Combustion promoting gas Oxygen (pure oxygen)
!
42
NA
FLO
N G
AS
KE
TS
Fluoropolymer Gaskets Having Excellent Anti-corrosion Property
NAFLONTM
PTFE Cut Gasket TOMBO� No.9007
This is anti-corrosion NAFLON gaskets made of pure PTFE sheets bypunching to the prescribed dimensions and shapes. As PTFE offers outstanding chemical resistance and does not contaminatefluids, it can be used as a gasket material in a wide range of industries.For the services more than 100℃, filled PTFE gaskets which improve anti-creep property is recommended.
■Applications¡Various corrosive fluids, such as strong acids, strong alkalis, organic solvents. ¡Fluids where contamination is not allowed.¡Services where electrical insulating property is required.
■Applicable standardsJPI-7S-75
TOMBO No. 9007
■Design standard
Fluoropolymer Gaskets Having Low Creep Property
NAFLONTM
Glass Fiber Filled PTFE Cut Gasket TOMBO� No.9007-G20
As PTFE is a thermoplastics, it easily softens at high temperetures and is alsosubject to cold flow. Under high bolt tightening, sealing stress is reduced bycold flow. In order to improve this property, 20% glass fibers filled PTFE isused. It can be used for almost all chemicals except strong alkalis, such assodium hydrate etc. and hydrofluoric acid.For the services where TOMBO No. 9007-G20 is not used, following gasketsare recommended.Service temperature more than 150℃ TOMBO No. 9007-LCStrong alkalis, Hydrofluoric acid TOMBO No. 9007-SC
■Applications¡Strong acids, such as Chloric acid, Nitric acids, Surfuric etc., organic solvents. ¡Services where electrical insulating property is required.
■Applicable standardJPI-7S-75
TOMBO No. 9007-G20
■Design standard
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, pleaserefer to page 45.*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, pleaserefer to page 45.*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
TOMBO No.Standardthickness
A
Maximumouter diameter
A
GasketfactorC
Minimumseating stress y
N/E
Maximum allowableseating stress
N/E
Servicetemperature
℃
Maximum(1)
service pressurMPa
9007
1.0
1200
3.5 24.5
39.2 –100~100 1.01.5 3.2 22.62.0 3.0 19.63.0 2.5 19.6
TOMBO No.Standardthickness
A
Maximumouter diameter
A
GasketfactorC
Minimumseating stress y
N/E
Maximum allowableseating stress
N/E
Servicetemperature
℃
Maximum(1)
service pressurMPa
9007-G20
1.0
980
3.5 24.5
49.0 –100~150 2.01.5 3.2 22.62.0 3.0 19.63.0 2.5 19.6
43
NA
FLON
GA
SK
ET
S
■Design standard
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, pleaserefer to page 45.*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
■Design standard
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, pleaserefer to page 45.*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
Fluoropolymer Gaskets Having Low Creep Property (Yellowish White Color)
NAFLONTM
Special Filler Filled PTFE Cut Gasket TOMBO� No.9007-LC
This is low creep PTFE cut gasket filled with a specialanti-corrosion, highly temperature resistant inorganicfiller. Its maximum service temperature is 200℃. This gasket can be used for almost all chemicals excepthydrofluoric acid and strong alkalis. For hydrofluoric acidand strong alkalis, TOMBO No. 9007-SC is recommended.
■Applications¡High temperature strong acids, such as chloric acid, nitric acid,
sulfuric acid etc.¡Petroleum and petrochemical products, organic solvents, heat
oil, heat media, steam.¡Services where electrical insulating property is required.
TOMBO No. 9007-LC
Fluoropolymer Gaskets Having Low Creep Property (Black Color)
NAFLONTM
Special Filler Filled PTFE Cut Gasket TOMBO� No.9007-SC
This is low creep PTFE cut gasket filled with specialcarbon. Its maximum service temperature is 200℃.This gasket can be used for almost all chemicals exceptoxidizing acids, such as sulfuring acid (conc.), nitric acid(conc.) etc.For oxidizing acids, TOMBO No. 9007 is recommended.
■Applications¡High temperature strong alkalis, such as sodium hydroxide,
potassium hydroxide etc.¡Petroleum and petrochemical products, organic solvents, heat
oil, heat media, steam.
■CautionThis gasket can not be used for the service where electricalinsulation is rerquired.
TOMBO No. 9007-SC
TOMBO No.Standardthickness
A
Maximumouter diameter
A
GasketfactorC
Minimumseating stress y
N/E
Maximum allowableseating stress
N/E
Servicetemperature
℃
Maximum(1)
service pressurMPa
9007-LC 2.0 1200 3.0 24.5 49.0 –100~200 3.0
TOMBO No.Standardthickness
A
Maximumouter diameter
A
GasketfactorC
Minimumseating stress y
N/E
Maximum allowableseating stress
N/E
Servicetemperature
℃
Maximum(1)
service pressurMPa
9007-SC 2.0 1200 4.0 29.4 58.8 –100~200 3.0
44
NA
FLO
N G
AS
KE
TS
Flexible Fluoropolymer Gaskets (Brown Color)
NAFLONTM
GL Gasket TOMBO� No.9007-GL
This gasket is made from PTFE with special anti-corrosionand heat resistant filler. Good in flexibility and suitablefor the pipings where high tightening stress can not beobtained, glass lined pipings and plastic pipings.This gasket can be used for almost all chemicals exceptstrong alkalis such as sodium hydroxidie andhydrofluoric acid. For the process which required whitecolor gasket, TOMBO No. 9007-FD is recommended.
■Applications¡Pipings and equipment which high tightening stress can not be
obtained, such as glass lined piping, plastic piping, equipmentmade from carbon, etc.
¡Strong acids, such as chloric acid, nitric acid, sulfuring acid etc.,organic solvents.
TOMBO No. 9007-GL
Flexible Fluoropolymer Gaskets (White Color)
NAFLONTM
FD Gasket TOMBO� No.9007-FD
This gasket is made from PTFE with special anti-corrosionand heat resistant filler. This is used for same applicationas TOMBO No. 9007-GL but this gasket is white color andmore flexible (soft) than TOMBO No. 9007-GL.This can be used for almost all chemicals except strongalkalis such as sodium hydroxidie and hydrofluoric acid.For gas sealing, TOMBO No. 9007-GL is recommended.
■Applications¡Pipings and equipment which high tightening stress can not be
obtained, such as glass lined piping, plastic piping, equipmentmade from carbon, etc.
¡Strong acids, such as chloric acid, nitric acid, sulfuring acid etc.,organic solvents.
TOMBO No. 9007-FD
■Design standard
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, pleaserefer to page 45.*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
■Design standard
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, pleaserefer to page 45.*Not recommended to use for gaseous fluids.
TOMBO No.Standardthickness
A
Maximumouter diameter
A
GasketfactorC
Minimumseating stress y
N/E
Maximum allowableseating stress
N/E
Servicetemperature
℃
Maximum(1)
service pressurMPa
9007-GL 3.0 600 2.5 19.6 39.2 –100~200 2.0
TOMBO No.Standardthickness
A
Maximumouter diameter
A
GasketfactorC
Minimumseating stress y
N/E
Maximum allowableseating stress
N/E
Servicetemperature
℃
Maximum(1)
service pressurMPa
9007-FD 3.0 1200 2.5 19.6 39.2 –100~200 2.0
45
NA
FLON
GA
SK
ET
S
Less Permeable Fluoropolymer Gasket (Brown Color)
NAFLONTM
LP Gasket TOMBO� No.9007-LP
Brown color gasket made from special PFA. This PFAmaterial has excellent chemical resistance, and permeationof chemicals and gases through resin is very small.Therfore, this gasket is suitable to seal halogens(chlorine, bromine etc.) which have very strongpermeability to fluoropolymer.
■Applications¡Strong alkalis, such as chloric acid, nitric acid, sulfuric acid etc.
and halogens.¡Petroleum and petrochemical products, various corrosive fluids,
organic solvents.
TOMBO No. 9007-LP
■Design standard
Notes : (1) Maximum service pressure at ambient temperature. This value becomes lower at high temperature. For details, pleaserefer to the figure below.*For gas sealing application, TOMBO No.9400 NAFLON PASTE is recommended to use.
TOMBO No.Standardthickness
A
Maximumouter diameter
A
GasketfactorC
Minimumseating stress y
N/E
Maximum allowableseating stress
N/E
Servicetemperature
℃
Maximum(1)
service pressurMPa
9007-LP 2.0 277 3.0 19.6 29.4 –100~100 1.0
NAFLONTM
PTFE Solid Gasket (TOMBO�
No. 9007 Series)
Service Range
Notes : (2) Not recommended to use for full face (Type FF)flange.
(3) Not recommended to use for gaseous fluids.
46
NA
FLO
N G
AS
KE
TS
■Gasket construction
Gasket type Cross section Construction and explanation
AThis is a standard enveloped gasket produced by slitting a sheet of PTFEand inserting cushion material, as shown.
B
This is an enveloped gasket for large diameters (generally 1000 mm dia.or larger). Oval gaskets are also available. Since there is a heat seal inone place, sealability is slightly inferior to that of type A. The use ofNAFLON paste (TOMBO No. 9400) is recommended.
AS
The same as type A but with a square inner section. There is little space inside the gasket,so there is less possibility of damage by the rapid expansion of air due to temperature rises.Appropriate design of the inside diameter reduces the accumulation of liquid and smoothesthe flow in the fluid.
R-AThe same as types A and AS but with the outer periphery sealed. Fluid fromthe exterior cannot penetrate or leak into the core. Because of thisconstruction, even when used in vacuum lines, the covering strongly resistsbeing pulled inside. Since there is no turning of the covering, setting issmooth even when the flange gap is narrow.
R-AS
PTFE Enveloped Gaskets
NAFLONTM
PTFE Cushion Gasket TOMBO� No.9010
The core of non-asbestos joint sheets, non-asbestos paper, etc.,which have high cushioning properties, are covered with a thinPTFE film. This gasket is more resistant to creep than a PTFEcut gasket (TOMBO No. 9007).Due to the PTFE film covering the inner diameter and sealingsurface of the gasket, there is no contamination of fluids.Furthermore, due to the excellent chemical resistance andsolvent resistance of the PTFE film, this gasket can be used fora wide range of applications in various fields such as finechemicals, petrochemicals, pharmaceuticals, foodstuffs, andgeneral industries.
■Applications¡Various corrosive fluids, organic solvents.¡Fluids where contamination is not allowed.¡Where electrical insulation is required.
■Applicable standardsJPI-7S-75
TOMBO No. 9010-NA-A-5, 9010-NA-R-A-5
TOMBO No. 9010-NA-A-7, NA-A-8, NA-A-9
■CautionsPlease refer to page 49.
47
NA
FLON
GA
SK
ET
S
■Type of Core
Core type Cross section and core material Construction and explanation
5Non-asbestos joint sheet (TOMBO No. 1995) is used as the core.Suitable for metal flanges which can obtain relatively high bolttightening stress.
6The core is a combination of non-asbestos joint sheet (TOMBONo. 1995) and non-asbestos paper. Good in cushioning andsuitable for glass lined flanges etc.
Non-asbestos joint sheet
Non-asbestos paperNon-asbestos joint sheet
7Non-asbestos joint sheet of core type 5 is replaced with hightemperature use non-asbestos joint sheet (TOMBO No. 1120).Non-asbestos joint sheet
for high tempereture use
8Non-asbestos joint sheet of core type 6 is replaced with hightemperature use non-asbestos joint sheet (TOMBO No. 1120).Non-asbestos joint sheet
for high tempereture useNon-asbestos paper
9The core is a combination of high temperature use non-asbestosjoint sheet (TOMBO No. 1120) and stainless steel mesh.Non-asbestos joint sheet
for high tempereture useStainless steel wire mesh
Notes : Cross sectional diagram is for A type.
Notes : (1) Not recommended for use in locations with frequent thermal fluctuations exceeding 100℃ and pressure fluctuation, or inlocations where maintenance work is difficult.
Notes : (2) The indicated service pressures are for ambient temperatures. These values become lower at higher temperature.For detailed service range, please refer to page 49.
■Indications
9 0 1 0 ─N A ─□─□
● Core type
● Gasket type
● Indication for non-asbestos
TypeMinimum inside
diameterA
Maximum outsidediameterA
Core typeGasket factor
C
Minimum seating stress
N/E
Maximum allowableseating stress
N/E
Servicetemperature
℃
Maximum (2)
service pressureMPa
A 16 1000
5, 6 3.5 14.7 29.4 –30~150 (1) 2.0
7, 8 3.5 14.7 29.4 –30~150 2.0
9 3.5 19.6 39.2 –30~200 2.0
AS 20 700
5, 6 3.5 14.7 29.4 –30~150 (1) 2.0
7, 8 3.5 14.7 29.4 –30~150 2.0
9 3.5 19.6 39.2 –30~200 2.0
B 300 As specified5, 6 4 19.6 29.4 –30~150 (1) 2.0
7, 8 4 19.6 29.4 –30~150 2.0
■Design standard
48
NA
FLO
N G
AS
KE
TS
■TOMBO� No. 9010 (Type A, B, AS)
Type of piping Flange standard Pressure rating SizeGasket type
Standard productsCore type Standard dimensions table
Ordinery piping
JIS B 2238-1996
5 K
10 K
16 K
20 K
10~600A
A
AS
B
A
AS
B
B
B
ASA
ASA
A
567895678956785678956789567856785678777768
P98
P100
P99
P98
P83
P87
P86
P83
P85
P84
P101
P88
P97
650~1500A
1 / 2~24B
14~60B
26~96B
26~60B
15~25A40~300A1 / 2~1B
1-1 / 2~12B
CLASS 75
CLASS 150
CLASS 300
CLASS 125
CLASS 250
CLASS 150
CLASS 300
10 K
150 LB
ASME B16.5
ASME B16.47
Series B
(JPI-7S-15-1999)
(JPI-7S-43-2001)
ASME B16.1
Taylor Forge
ASME B16.47Series A
(MSS SP-44-1996)
JIS
ASME(JPI)
20~200A10KAsahi Techno Glass GL piping
NAFLON linedpiping
Glass lined piping
Other Piping Please consult with us for detailed designing.
■TOMBO� No. 9010-NA (Type R-A, R-AS)
Type of piping Gasket standard Pressure rating SizeGasket type
Standard productsCore type Standard dimensions table
Ordinery piping
Other Piping Please consult us for detailed designing.
JIS B 2238-19965 K
10 K10~600A
R-A
R-AS
56785678
P102
P103
*Please consult with us for the products other than standard material, struction and dimensions.
■NAFLONTM
PTFE Cusion Gasket Standard products list for various pipingFor safety use by maintaining original function of NAFLON PTFE cushion gasket, we set the standard material,
shape, dimension for several piping materials.
Please select right products with refering the table below.
49
NA
FLON
GA
SK
ET
S
NAFLONTM
PTFE Cushion Gasket (TOMBO�
No. 9010 Series)
Core type 5 - 8 (For core type 5 and 6, Core type 5 and 6 is not recommended for the place where thermal and pressure fluctuation is often happened and the place where maintenance work is difficult.) Core type 9
Temperature(�)
Pressure MPa
■Flange FinishThe recommended surface roughness of metalflange is 6.3μmRa.
■For Gas SealingTo seal gases, TOMBO No. 9400, NAFLON Pasteshall be applied.
■For Installation¡Before setting the gasket, make sure that flange
surface is free from foreign material or scratch.¡When setting the gasket, make sure to have
enough distance between flanges. If gasket isforced to insert, it may cause leakage bydamaging the gasket or peeling off of PTFEenvelope.
¡If enough distance between flanges are notavailable, "R" type is recommended.
¡This type will prevent damage and peeling off ofPTFE envelope during installation.
¡For core types of 6 and 8, seating stress atcompression failure declines when the gasketbecomes wet.Therefore, store the gaskets in water-proof bags.In addition, take precautions so that gasket doesnot become wet by rain after installation.If the gasket is not tightened enough, soap-waterfrom pneumatic testing or rain-water couldpermeate and soften the non-asbestos paper,pushing non-asbestos paper out of the gasket.Take precautions since in such cases, the seatingstress on the gasket decreases and leakage can occur.
¡Do not reuse materials that have already beenused once.
■Seating Stress¡Seating stress of gasket shall be controlled to
maintain 29.4N/mm2 max.¡If gasket seating stress becomes more than this
value, jointing sheet of the core may be destroyed.Uneven tightening also results excess seatingstress partly and will cause for compressive failure.
¡Special attention shall be paid for bolt tightening.¡For Fluoropolymer lined piping, we set
recommended tightening torque size by size. Fordetails, please consult us.
■Air tight test¡When air tight test is conducted after installation,
bubble may be observed between PTFE envelopeand core material.
¡This is the air accumulated inside of cushioningmaterial or between the cushioning material andPTFE envelop.
¡Especially for core type 6 and 8, these corematerials have such tendency.
¡So, air tight test shall be conducted well afterinternal pressure is applied.
■Others¡Bolt tightening may be loosen in long time or after
heat cycles.¡Bolt tightening shall be checked periodically and
when bolt is loosen, re-tightening shall be done byinitial bolt torque.
¡When thermal stress or bending stress isrepeatedly applied to the flanges, gasket seatingstress is easily reduced.
¡This gasket is not recommended for such part.
■Cautions for selection of PTFE Cushion gasket¡Some of the fluids may permeate to inside of the
gasket thru PTFE envelope.¡Especially nitric acid, ethylene chloride, halogens
(chroline, bromine, etc.), molten sulfur and mono-chloroacetic acid may attack the cushioningmaterial by permeation in long time and as aresult, gasket function will be lost. In such case,gasket shall be changed periodically or use PTFEcut gasket instead.
¡When type "A", "B" and "AS" type is used forvacuum service, PTFE envelope may be pulled in.In such case, "R" type is recommended.
¡Due to its shape of "A" type, fluid may remain inthe space between flanges and gasket. To avoidthis fluid remaining, "AS" type with appropriategasket inner diameter shall be used.
¡For plastic, glass and rubber lined pipings, eachflange has different gasket dimensions althoughflange standard is JIS standard. Please consult usfor proper gasket dimensions if the gaskets areused for such pipings.
■Cautions for NAFLONTM
PTFE Cushion Gasket
■Service Range
50
NA
FLO
N G
AS
KE
TS
Electrical Insulation Bolt Kit TOMBO� No.9910 / 9910-H
Electrical Insulation Bolt kit is designed for cathodicprotection.This kit consisits of bolt with factory applied insulatingsleeve, insulating washers, metal washers and nuts.
■Features¡Excellent in electrical instulating performance
As all contact area with metal is covered with fluoropolymer andother high performance materials.
¡Easier installation.As insulating sleeve is already applied to bolt, trable of fittingduring installation, such as cracking, chipping, displacement etc.can be eliminated
¡Solution for complicated purchasing and management.The problem of excess and deficiency will be resolved becausenecessary number of metal washer, insulation washer and nutare combined as a set for one bolt.
■Standard SizeASME Flanges : Class 150 - 1/2" to 60"
Class 300 - 1/2" to 60"JIS Flanges : 10K - 10A to 1500A
20K - 10A to 900AIndication of sizeStandard size : "Pressure rating" x "Flange size"
ex. Class 150 x 8", JIS 10K x 200ANon-standard size : "Thread dia." x "Total Length" x
"Insulation sleeve length"ex. M20 x 100L x 40LS
TOMBO No. 9910
TOMBO No. 9910-H
Cross Section : TOMBO No. 9910
■Design standard
■Physical properties of insulaing material
TOMBO No.9910Service Temperature -30~150℃
Insulating Sleeve PVdF coating by baking(PVdF: Polyvinylidene fluoride)
*This table shows pyscal properties of insulating materials to be used for parts of insulation bolt kit. Pyscal properties of each part ofinsulation bolt may vary from this table due to manufacturing process and size.
*Above fugure is general characteristics. Not for specification nor guarantee.
Insulating Gasket
Insulating Bolt
Metal WasherInsulating Washer
PVdF Coating
PVdF PTFE FRP FRS(Epoxy) (Silicone)
Tensile Strength Mpa 38~51 27~34 294~343 69~118
Compressive Strength Mpa 60 12 196~490 294~519Hardness Shore D Shore D Rockwell Rockwell
80 50~55 120~125 118~122Dielectric Strength KV/A 10 19 22~27 10>Volume Resistivity Ω-B >1014 >1018 >1014~>1016 >1011~>1015
Surface Resistivity Ω >1013 >1016 >1012~>1014 >1012~>1014
Water Absolution % 0.04 <0.01 0.1~0.3 <0.35Heat Resistance ℃ 150 260 180 200
TOMBO No.9910-H-30~200℃ (with FRS washer)
PTFE tube lining
Glass reinforced epoxy (FRP) : up to 180℃ orGlass reinforced sillicone (FRS) : up to 200℃SNB7 (Unified screw thread)For ASME flange
Insulating Washer Glass reinforced epoxy (FRP)
Bolt SNB7 (Unified screw thread)SS400 (Metric screw thread)
S45CFor JIS flangeFor ASME flange
SS400 (Metric screw thread)
SS400SS400
Nut S45CFor JIS flange SS400
Metal washer (as per JIS B1256) SS400
51
NA
FLON
GA
SK
ET
S
Electrical Insulation Gasket TOMBO� No.9010-NA-E5 / 9007-LC
NAFLON PTFE has excellent electrical insulatingproperties.This electrical insulating gasket is made of PTFE and tobe used for electrical insulation between flanges.
2 types of gaskets are available for your application.
■Features¡TOMBO No. 9010-NA-E5
This gasket is flexible and can be sealed with relatively lowseating stress. As PTFE has very good chemical resistance aswell, it can be used for various types of fluids such as corrosivefluids (acids / alkalis), organic solvents etc.
¡TOMBO No. 9007-LCThis gasket is punch out gasket from low creap PTFE sheet withspecial inorganic filler. Maximum service temperature is 200℃.
■Standard SizeASME Flanges : Class 150 - 1/2" to 60"
Class 300 - 1/2" to 60"JIS Flanges : 10K - 10A to 1500A
20K - 10A to 900A
TOMBO No. 9010-NA-E5
TOMBO No. 9007-LC
■Design standard
■Service Range
Type Cross section and core material Structure
TOMBO No.9010-NA-E5
A type(Up to 24B or 600A) Standard products. Ring shape PTFE is
slitted and inserting cushion materials(TOMBO No. 1995)Standard size is up to 24" or 600A.B type
(26B or 650A andabove)
TOMBO No.9007-LC
Standard products for large diameter(26" and avove) or oval shape. As thereis a heat seal in one place, sealperformance is inferior to that of A type.
NAFLON PTFE Sheet
TOMBO No.1995Non-asbestos joint sheet
NAFLON PTFE Sheet
TOMBO No.1995Non-asbestos joint sheet
3.0
2.0
1.0
0-30 0
Temperature(℃)
Pre
ssu
re (
MP
a)
100 200
TOMBO No.9010-NA-E5(1)
TOMBO No.9007-LC
Note : (1) Not recommended for use in locations with frequentthermal fluctuations exceeding 100℃ and pressurefluctuation, or in locations where maintenance work isdifficult.
52
NA
FLO
N G
AS
KE
TS
TOMBO No. 9022-A TOMBO No. 9022-PFA TOMBO No. 9028
■Other Fluoropolymer Gaskets
Type TOMBO No. Product Name Construction and explanation
O-ring
Free-sizegasket
9022-A
This rubber O-ring is covered with thin (0.4A) PTFE film.PTFE covering has one overlap joint, but it is not securedwith adhesive. We offer type A and type B, and type A isused for gaskets.
NAFLONPTFE Covered RubberO-ring
9022-PFAThis fluoro-rubber (FA) O-ring is completely covered witha PFA tube. The PFA is seamless but the inner rubber O-ring has an open joint.
NAFLONPFA Covered Rubber O-ring
9028
This O-ring is machined form PTFE. There are three types: pure PTFE (TOMBO No. 9028), glass filledPTFE (TOMBO No. 9028-G20) and graphite filled PTFE(TOMBO No.9028-GR30).
NAFLON PTFE O-ring
9037A free-size string shape packing made by extrudingunsintered PTFE.
NAFLON SP Packing
9096
Soft type gasket made of expanded PTFE. Various cross sectional shapes areavailable such as oval, round (R), flat (B), square (K), tube (TB) as well as flatsheet (S). Oval shape is supplied with adhesive tape. Round (R) and tube (TB)shapes are supplied without adhesive tape. For flat (B), square (K) and flatsheet (S) shapes, both with and without adhesive tape are available.
NICHIAS Soft Seal
Other NAFLON gaskets available are TOMBO No. 9090 NAFLON Vortex and TOMBO No. 9094 NAFLON Manhole Gasket. For details,refer to each section.
■Standard dimensionsTOMBO No. Diameter (A) x Length (mtr)
2.4×159037 4.0× 9
5.6× 5
TOMBO No. Thickness(A)×Width(A)×Length(mtr)1.5× 3×30
9096 3.0× 6×154.5× 9× 86.0×12× 5
Note: TOMBO No. 9096 (oval) is treated withadhesive tape.
TOMBO No. Diameter(A)× Length(mtr)10×5
9096-R 12×520×5
TOMBO No. OD (A)×ID (A)×Length (mtr)2× 1×303× 2×304× 3×305× 4×20
9096-TB 6× 5×207× 6×208× 7×10
10× 8×1012×10×10
Note: TOMBO No. 9096 (round) is nottreated with adhesive tape
53
NA
FLON
GA
SK
ET
S
TOMBO No. 9037 TOMBO No. 9096(OVAL)
Cross section Applications, service conditions Service temperature℃
Used as internal pressure sealinggaskets. Cannot be used for shaftsealing (both fixed and moving).
Depends on therubber material.
–15~180
–100~150
(Type A)
When used as a fixed O-ring, use at acompression ratio of 20 - 30%.This gasket is fitted into the groove like arubber O-ring.
Used for flange groove in the same way as rubber O-rings.Compression ratios are higher than for rubber O-rings. O-ring diameter 3.5A or less: 28% or more; 3.5 - 5.7A: 24%or more; 5.7A or larger: 22% or more.
–100~150Flanges for chemical ducts, low-pressuregas, etc.
–100~200Ducts, casing, large-diameter vessels,various types of lined vessels, etc.
(Oval type)
TOMBO No. Thickness(A)×Width(A)×Length(mtr)1.0× 20×15
9096-BT 1.0× 30×151.0× 50×151.0×100×152.0× 20× 52.0× 30× 5
9096-B 2.0× 50× 53.0× 20× 53.0× 30× 53.0× 50× 53.0×100× 5
9096-KT 5.0× 14×109096-K 7.0× 20× 5
TOMBO No. Indications of type Thickness(A) Width(A)×Length(A)
9096
-S(Without adhesive
tape)
-0.5 0.5
1500×15001500×3000
-1.0 1.0-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0-5.0 5.0-6.5 6.5-10.0 10.0 1500×1500
-ST(With adhesive
tape)
-1.0 1.0
1500×1500-1.5 1.5-2.0 2.0-3.0 3.0-4.0 4.0
54
CLO
TH
GA
SK
ET
S
Manhole Gasket■Features : These are cloth gaskets coated with a rubber
compound, matching the shape of the manhole.These gaskets are not completely airtight and should beused only where a certain amount of leakage is allowable.Suitable for application to large diameter distortedflanges and flanges to which only low seating stress isapplied.
TOMBO No. 1374, 1400-NA, 1400-S■Types
TOMBO No. Product name Construction Application Maximum service temperature (℃) Coroer
1374
1374-G
1378
1400-TH
1400-THG
1400-NA
1400-ST
1400-S
9094
400
400
400
600
600
800
300
NA Manhole gasketMade by coating glass cloth with naturalrubber using endless processing method.
NA Manhole gasket(Treated with graphite)
TOMBO No. 1374 is treated with graphite foranti-sticking.
NA gasket with core Both sides of the TOMBO No. 1368 NA gasket tape with coreare sewn into a ring with glass yarn to make the gasket.
FF Manhole gasketBoth sides of the FINEFLEX cloth reinforced with metalwires are coated with a special composition rubber and anendless processing method is used.
FF Manhole gasket(Treated with graphite)
TOMBO No. 1400-TH is treated with graphitefor anti-sticking.
Super Manholegasket-ST
The base cloth is woven by using metal wires as thewarp, and ceramics yarn containing metal wires as thewoof, then impregnating the cloth with heat resistantjoint filler and using an endless processing method.
800Super ManholeGasket-S
The based cloth is woven by using metal wires as thewarp and ceramic yarn reinforced by metal wires as thewoof, then impregnating the cloth with heat resistantjoint filler and using an endless processing method.
600
White
Black
White
White
Black
White
White
Black
BlackSuper ManholeGasket
The based cloth is woven by using metal wires asthe warp and glass yarn reinforced by metal wiresas the woof, then coating the cloth with rubber andusing an endless processing method.
NAFLON Manholegasket
Inorganic cloth, woven using a special method, isimpregnated with PTFE dispersion. This is thenformed into the shapes of various gaskets.
Manholes/handholesfor exhaust gas, hotair, etc.autoclaves, largediameters flanges.
Diesel engine exhaustpipes, flue gas ductmanholes, boilercombustion ductsealing materials.
Ducts requiringchemical resistance andsolvent resistance/ductsfor corrosive gasessuch as acid exhaustgas, and general gases.
1374, 1374-G ─ ─ ─ ◯ ─ ◯ ─ ─ ◯ ─ ◯ ◯ ─1378 ─ ─ ─ ◯ ─ ─ ─ ─ ─ ─ ─ ─ ─
Manhole 1400-TH,1400-THG ─ ─ ─ ─ ◯ ─ ─ ◯ ─ ─ ◯ ─ ◯
Gasket 1400-ST ─ ◯ ─ ─ ─ ─ ◯ ─ ─ ◯ ─ ─ ◯1400-NA ─ ─ ─ ◯ ─ ◯ ─ ─ ◯ ─ ◯ ◯ ─1400-S ─ ─ ◯ ─ ─ ─ ◯ ◯ ─ ─ ◯ ─ ◯9094 ◯ ─ ─ ◯ ─ ◯ ─ ─ ◯ ─ ─ ─ ─
Gasket tape
1364 ─ ─ ─ ◯ ─ ◯ ─ ─ ◯ ─ ─ ─ ─
1368, 1368-G ─ ─ ─ ◯ ─ ─ ─ ─ ─ ─ ─ ─ ─
55
CLO
TH
GA
SK
ET
S
Gasket Tape■Features : This is a cloth tape gasket coated with a
rubber compound to form a multi-layer structure.These gaskets are not completely airtight and should beused only where a certain amount of leakage is allowable.Suitable for application to large diameter distortedflanges and flanges to which only low seating stress isapplied.
TOMBO No. 1364
■Types
TOMBO No. Product name Cross Section Construction Application
1364
1368
1368-G
400
400
400
NAGasket Tape
A tape shaped gasket made by glass clothwith natural rubber coating and thenfolding it.
Manholes/handholes for low-pressure steam,exhaust gas, hotair, etc.,autoclaves, largediameters flanges.
Doors anddampers forfurnaces, heatersand dryers, etc.Manholes forexhaust gas, hotair, and dust, etc.
TOMBO No. 1368 is treated with graphite for anti-sticking.
NA TadpoleGasket tape
NA tadpolegasket tape(Finished withgraphite)
A tape shaped non-asbestos gasket. This is madeby woven glass cloth with rubber compound andwinding it into a Vortex core. Then the outercovering made of the same materials is formed,as shown in the diagram.
■Standard dimensions
Type TOMBO No. Nominal thickness Dimensions1.6 2.5 3.0 3.2 4.0 4.8 5.0 6.0 6.4 7.5 8.0 9.6 10.0
As specified.
Width : 13, 20, 25, 30, 40, 50ALength: 30mtr
3 layer wrap
4 layer wrap
Height : 6.4, 7.9, 9.5, 11.1, 12.7,15.9, 19.1, 22.2, 25.4A
Width : 50A Length : 30mtr
Maximum servicetemperature (℃)
White
White
Black
Coroer
56
RU
BB
ER
GA
SK
ET
S
Rubber Cut Gasket TOMBO� No.1050/1051
■Features : The elasticity, recovery and compatibility ofrubber are utilized to assure sealing at the lowest seatingstress. TOMBO No. 1051 is reinforced with polyestercloth, but is unsuitable for gas sealing.
■Applications Select the material in accordance with the serviceconditions for various piping flanges, equipment, etc.
■Service Range Service temperature range : depends on the rubber material.Maximum service pressure : 1.0MPa
TOMBO No. Product name Construction
1050
1051
Gasket cut from various types ofrubber sheets.Rubber Cut Gasket
Cloth ReinforcedRubber Cut Gasket
Gasket cut from various types ofrubber sheets reinforced withpolyester cloth.
Unit: A■Standard dimensions
Thickness 1.0 1.5 2.0 3.0 5.0 10.0 OthersWidth 1000Length 1000, 2000, 5000, 10000, 20000
*ZR and PF dimensions are 300 (W) x 300 (L) x 1, 1.5, 2 or 3A (T).
*TOMBO No.1051 is only available for "NBR", "CR" and "NR".
Rubber O-ring TOMBO� No.2670
■Features : These are self-sealing type rubber O-ringsproduced by molding various types of rubber into circularshapes. These can be used as shaft seals (packing) and asgaskets by fitting them into grooves. Sealing is good evenwith low tightening loads and throughout a range fromvacuum to high pressure up to 25MPa. For semi-conductor / LCD production equipment use orhigh temperature application up to 300℃, other brochureis available separately. Please consult with us for details.
■Applications Select the material in accordance with the fluid (materialsare the same as for TOMBO No. 1050). Gaskets for various types of devices.
■Service rangeService temperature range : depends on the rubber
material.Maximum service pressure : 25MPa (can be used for
greater pressure if used withback-up ring.)
■Applicable standardsJIS B 2401 AS 568 A
■Indications
1 0 5 0 ─□□ ● Material code
● TOMBO No.
2 6 7 0 ─□□ ● Material code
● TOMBO No.
Material code NBR CR EP IIR SI FA FS NR ZR PF
Materrial Nitryl rubber(oil resistant)
Chloroprene rubber(weather resistant)
Ethyl propylene rubber(weather resistant,
steam resistant)
Butyl rubber(weatherresistant, acid resistant,
steam resistant)
Silicone rubber(weather resistant,
cold resistant)
Fluorocarbonrubber
(heat resistant)
Fluorocarbonrubber
(corrosion resistant)Natural rubber
Hydrogen addednitryl rubber(oil resistant)
Perfluoroelastomerrubber
(corrosion resistant)
Service temperature -30~120 -30~120 -40~150 -30~150 -60~230 -15~200 0~200 -20~100 -30~150 0~200TOMBO No.1050 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○TOMBO No.1051 ○ ○ - - - - - ○ - -TOMBO No.2670 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
■Type
■Material codes and materials
57
RU
BB
ER
GA
SK
ET
S
EbilonTM
Gasket (Solid Rubber)TOMBO� No.9013-EP/-DEP
■Features : Rubber molded gaskets having a crosssectional shape as per diagram below. Reliable sealingperformance is obtained even at lower seating stress thanthat of rubber gasket.Recommended for locations where service conditions arenot critical and chemical resistance is not particularlyrequired.
■TypesThere are two types using different types rubber.TOMBO No. 9013-EP: EPDMTOMBO No. 9013-DEP: Special EPDM for electrolytic cells.
■Service rangeService temperature : –40℃~ 150℃Maximum service pressure : 1.0MPaFlange : Full face
■Standard dimensionsPlastic flanges (equivalent to JIS 10K): 15A - 300AASME B16.5 (JPI), Class 150 1/2B ~ 24B
TOMBO No . 9013-EP
Rubber Rubber
TOMBO No . 9013
EbilonTM
Gasket (PTFE Jacketed) TOMBO� No. 9013/9013-D
■Features : Rubber molded gasket having the same crosssectional shape as TOMBO No.9013 but sealing surface isjacketed with PTFE film. This gasket has the elasticity ofrubber and the corrosion resistance of PTFEsimultaneously and gives good sealing performance.Ebilon gaskets are ideal for applications such as PVCpiping and glass lining piping, where only low seatingstress is attainable.
■TypesThere are two types using different rubber.TOMBO No. 9013 : PTFE jacketed EPDMTOMBO No. 9013-D : Special EPDM with jacketed PTFE
for electrolytic cells.
■Service rangeService temperature : –30℃~ 150℃Maximum service pressure : 2.0MPaFlange : Full face flangesFlange finish : 6.3 Ra or smoother
■Standard dimensionsPlastic flanges (equivalent to JIS 10K): 15A - 300AASME B16.5 (JPI), Class 150 : 1/2B ~ 24B
RubberPTFE Rubber
Type
58
OT
HE
R G
AS
KE
TS
■Standard dimensions
Sanitary Use Gasket
SanicleanTM
Gasket TOMBO� No.9014
This is sanitary use rubber molded gaskets having PTFEfilm covering on the sealing surface of the gasket. Thanksto this unique structure, this gasket has advantages ofrubber gasket and PTFE.
Following types are available.¡For thread connector
TOMBO No. 9014-A (Black color EPDM rubber)¡For ferrule
TOMBO No. 9014-B (Black color EPDM rubber)TOMBO No. 9014-BW (White color EPDM rubber)
■Features¡All the contact surface with fluid is covered with PTFE film.
So, it is durable against hot water, alkalis, chlorine water etc.and lasts longer than rubber gaskets.
¡As all the contact surface with fluid is PTFE, fluid is not adheredto surface and not permeate to inside. So contamination atflavor change is avoided.
¡Sanitation process and time can be reduced at flavor change andincrease productivity.
¡Basically same application procedure as conventional rubbergasket but re-tightening process is required additionally.
Note : Flavor change : Change of product at common use beverage
manufacturing process such as bottling etc.Sanitation : Cleaning work. Washed with clean water,
chlorine water, hot water, alkalis etc.
TOMBO No. 9014-A, For thread connector
TOMBO No. 9014-B, for Ferrule (Black rubber)
TOMBO No. 9014-BW, For Ferrule (White rubber)
φA
φA
φB
φB
φC
PTFE(0.3t)
PTFE(0.3t)
Rubber(EPDM)
Rubber(EPDM)
R1.2
6.5 5.
5
48
5.3
1.7
1.7
20
φB
φC
TOMBO No. 9014-A(For thread connector)
TOMBO No. 9014-B / BW(For Ferrule) *Standard dimensions for TOMBO No. 9014-A, B, BW are set by us in accordance IDF standard.
However, it can also be used for the connectors and ferrule as per ISO 2852 and ISO 2853.
NominalSize
(Inch)
TOMBO No. 9014-A (Thread) TOMBO No. 9014-B, BW (Ferrule)
φA φB φC φA φB φC
1 32.5 29.2 23.0 49.5 43.5 23.1
1-1/2 46.0 42.7 35.6 49.5 43.5 35.8
2 59.5 56.2 47.8 63.0 56.5 48.0
2-1/2 73.0 69.9 59.5 76.5 70.5 59.7
3 86.5 82.6 72.1 90.0 83.5 72.3
4 112.5 108.3 97.6 118.0 110.0 97.8
* TOMBO No. 9014, Saniclean Gasket conforms to standard of food and food additives (Noticeby Japanese ministry of health and welfare No. 370 in year 1959), No.3-D-2, apparatus ofsynthetic resin.Also it passed material and elution test of container and packaging material (Notice byJapanese ministry of health and welfare No. 85, revised in 1986).
NA beater sheet
59
OT
HE
R G
AS
KE
TS
■Other Gaskets
TOMBO No. 1600 TOMBO No. 6526 TOMBO No. 6750-P
TypeTOMBO
No.Product name
Construction and features ApplicationMax
temperature(℃)Applicablestandards
Rubber coatedmetal gasket
1600 METAKOTE�
A high-performance gasketmaterial formed from thelamination of rubber andmetal sheet. Both sides ofmetal sheet are coatedwith rubber and finishedwith graphite.
Engine Gaskets,Cylinder headgaskets, Hydraulicand Pneumaticequipment gasketsCompressor gaskets(air conditioning,freezer, refrigeratoretc.), sealingwashers
Dependson grade
–
Non-asbestosbeater sheet
6526NA Beatersheet
Non-asbestos beater sheetsmade of special heat-resistantfibers, NBR rubber latex andheat-resistant fillers.
Gaskets for oil andwater devices, etc.
150ASTMF104
(F304140)
Non-asbestosmill board
6750-PVermosulSheet-P
Non-asbestos mill boardmade of inorganicminerals and inorganicbinder.
Combustion gas sealsfor hot air heaters,high-temperature (lowpressure) gaskets.Cannot be used asgaskets for pipingsand equipment.Not suitable for fluidsealing.
800 –
■Standard Dimensions of NA beater sheetTM / Vermosul sheetTM-P
■Standard Products of METAKOTETM / METAFORMTM
¡Typical grade
¡Master coil size of METAKOTE / METAFOAMMaster coil width : 914 mm width (effective width 876 mm) *Slited coils to your requirement is also available.
Unit: A
Thickness 0.5 0.8 1.0
TOMBO No.6526 500 ×1000
Vermosul sheet-P
Thickness 1.0 1.5 2.0 3.0 5.0 6.0
TOMBO No.6750-P 1000 ×1000
Unit: A
Foamed rubbercoated metalgasket
1608 METAFOAM�
Gasket material made ofmetal sheet coated withfoamed rubber forexcellent sealing andvibration dampingproperties.
Engine gasket,Hydraulic andPneumaticequipment gaskets
Dependson grade
–
TOMBO No. 1600, METAKOTETM
Grade For automobile gasketsTS Combination of cold rolled steel (carbon steel) and NBRJZ Combination of stainless steel sheet SUS301H and NBR
LZ Combination of stainless steel sheetSUS301H and Fluoroelastomer (FKM)
Grade For refrigeratorsRS Combination of cold rolled steel (carbon steel) and NBRRA Combination of aluminum sheet and NBR
Notes : (1)These grades are subject to change without notice.Notes : (2)For other application such as brake shim, washers etc., please consult us.
TOMBO No. 1608, METAFOAMTM
Grade For general purpose
PS Combination of cold rolled steel (carbonsteel) and NBR base foam rubber.
PA Combination of aluminum sheet andNBR base foam rubber.
60
GA
SK
ET
PA
ST
E
Aqua-tight Paste TOMBO� No.9105
Gasket paste for water base fluids, made of fine micaparticles mixed with special oil-soluble binder.
Oil-tight Paste TOMBO� No.9106
Gasket paste for oil base fluids, made of fine mica particlesmixed with oil and solvent resistance water soluble binder.
Anti-corrosion Paste TOMBO� No.9120
Gasket paste for asbestos and NA joint sheets when they areused for stainless steel flanges. Coating anti-corrosion pasteon the surface of the gasket prevents corrosion and pittingof stainless steel flanges.
!
Notes: Do not use for fluids if even slight dissolution is prohibited.
–200~900℃Light beigeapprox. 200N/G (12.5G/can)2.5O plastic container
Petroleum type oils, oil gas, solvents, solvent vapor, animal oils,hydrocarbon type fluids, exhaust gas, etc. This is suitable for oil, etc.
250℃GrayApprox. 350N/G (8.5G/3O can)1O can and 3O can
Notes: Do not use for fluids if even slight dissolution is prohibited.
Water (except brine).Oil, etc.
Water type fluids such as water, water vapor,sea water, acids, alkalis,salt solutions, etc.–200~200℃Light beigeApprox. 200N/G (12.5G/can)2.5O plastic container
Fluids
Maximum service temperatureColorCoveragePackage
Fluids
Maximum service temperatureColorCoveragePackage
Notes: Do not use for fluids if even slight dissolution is prohibited.
Fluids
Maximum service temperatureColorCoveragePackage
Gasket paste is a sealing aid that enhances the sealing performance of
various types of gaskets, prevents scorching and leaks.
Warning Gasket paste is for supplementing the sealing function ofgaskets and cannot be used alone. Always use to apply on gaskets.
■Gasket Paste
Hazardous cargo for ocean / air transportation, IMCO class 3, UN No.1993, Flash point 27-32℃. For details,please refer to MSDS available separately.
61
GA
SK
ET
PA
ST
E
NAFLON™ Paste TOMBO� No.9400
General purpose gasket paste, made by dispersingfine colloidal particles of PTFE in water. Thisgasket paste is inactive at ambient temperature.As it is also chemical resistant, this paste can beused for acids and corrosive fluids. For PTFE typegasket, this paste is most suitable.
PTFE Grease TOMBO� No.9401
Lubricating grease made from PcTFE oil mixedwith fine PTFE particles in it. Good in heat andchemical resistance and lubrication. This grease isincombustible.
Fluids
Maximum service temperatureColorCoveragePackage
Water, oil, acid, corrosive fluids, vacuum.
260℃WhiteApprox. 50N/G (2G/tube)65" (approx. 100N) tube.
Notes: Do not use for fluids if even slight dissolution is prohibited.
Oxygen, corrosive fluids, vacuum.
150℃WhiteApprox. 50N/G50N tube.
Notes: Do not use for fluids if even slight dissolution is prohibited.
Cautions1. For gasket paste in can, stir well before using. 2. Small amount layer with a brush, waste, etc. Excessive application may result in gasket damage.3. To improve the gas sealing performance with joint sheet,
apply gasket paste on the inner circumference to avoid leakage.4. Place the gasket on the flange before the gasket paste completely dries.5. Store in a cool, dark place.
Fluids
Maximum service temperatureColorCoveragePackage
Standard
Dim
ension Charts
63
Standard Dimension Charts
Index ────────────────────────────
For ASME FlangesFor JPI FlangesFor Taylor Forge & Ladish FlangesFor MSS Flanges
●Soft Gasket Standard DimensionsFull Face Gaskets (for B16.1, B16.5) …………………………………………………………………………………………… 64Flat Ring Gasket (for B16.1, B16.5)……………………………………………………………………………………………… 65Flat Ring Gasket (for B16.47 Series A, MSS) ……………………………………………………………………………… 66Flat Ring Gasket (for B16.47 Series B, API)………………………………………………………………………………… 67Flat Ring Gasket (for Taylor Forge) ……………………………………………………………………………………………… 67T&G, M&F ……………………………………………………………………………………………………………………………………… 68
●Vortex Gasket Standard DimensionsFor B16.5, B16.47 Series B…………………………………………………………………………………………………… 70~73For B16.47 Series A, MSS …………………………………………………………………………………………………………… 74For B16.5 T&G, M&F …………………………………………………………………………………………………………………… 75For Taylor Forge & Ladish …………………………………………………………………………………………………… 76~77
●Ring Joint Gasket Standard DimensionsFor R Ring ……………………………………………………………………………………………………………………………… 78~79For RX Ring …………………………………………………………………………………………………………………………………… 80For BX Ring …………………………………………………………………………………………………………………………………… 81Correspondence of Ring No. and Flanges…………………………………………………………………………………… 82
● NAFLONTM PTFE Cushion Gasket Standard DimensionsFor B16.5, B16.47 Series B (A & B type)……………………………………………………………………………………… 83For B16.47 Series A, MSS (B type) ……………………………………………………………………………………………… 84For B16.1, Taylor Forge (B type) ………………………………………………………………………………………………… 85For B16.5 (AS type) ……………………………………………………………………………………………………………………… 86For B16.5 (For high temperature applications) …………………………………………………………………………… 87For B16.5 (For NAFLON lined piping) ………………………………………………………………………………………… 88
●Ebilon Gasket Standard Dimensions ………………………………………………………………………………… 89●Electrical Insulation Bolt Kit Standard DimensionsFor Class 150 ………………………………………………………………………………………………………………………………… 90For Class 300 ………………………………………………………………………………………………………………………………… 91
For JIS Flanges
● Soft Gasket Standard Dimensions …………………………………………………………………………… 93~95● Vortex Gasket Standard Dimensions………………………………………………………………………… 96~99● NAFLONTM PTFE Cushion Gasket Standard Dimensions…………………………………… 100~105● Ebilon Gasket Standard Dimensions ……………………………………………………………………………… 106●Electrical Insulation Bolt Kit Standard DimensionsJIS 10 …………………………………………………………………………………………………………………………………………… 107JIS 20 …………………………………………………………………………………………………………………………………………… 108
For ASME B16.1 FlangesFor ASME B16.5 Flanges Soft Gasket/Full Face Gasket (F.F.)
64
Sta
ndar
dD
imen
sion
Cha
rts
Nominal Pipe
Size
Inner
diameter
D1
For ASME B 16.1 Cast iron flanges For ASME B 16.5 Steel flanges
Class 25 Class 125
Outer diameterD2
Bolt circle diameterC n × h Outer diameter
D2Bolt circle diameter
C n × h
Class 150
Outer diameterD2
Bolt circle diameterC n × h
Dimension Chart 1 Unit : A
1/2 21.3 ─ ─ ─ ─ ─ ─ 88.9 60.5 4×15.7
3/4 26.9 ─ ─ ─ ─ ─ ─ 98.6 69.8 4×15.7
1 33.3 ─ ─ ─ 108.0 79.2 4×15.7 108.0 79.2 4×15.7
11/4 42.2 ─ ─ ─ 117.3 88.9 4×15.7 117.3 88.9 4×15.7
11/2 48.5 ─ ─ ─ 127.0 98.6 4×15.7 127.0 98.6 4×15.7
2 60.5 ─ ─ ─ 152.4 120.6 4×19.0 152.4 120.6 4×19.0
21/2 73.2 ─ ─ ─ 177.8 139.7 4×19.0 177.8 139.7 4×19.0
3 88.9 ─ ─ ─ 190.5 152.4 4×19.0 190.5 152.4 4×19.0
31/2 101.6 ─ ─ ─ 215.9 177.8 8×19.0 215.9 177.8 8×19.0
4 114.3 228.6 190.5 8×19.0 228.6 190.5 8×19.0 228.6 190.5 8×19.0
5 141.2 254.0 215.9 8×19.0 254.0 215.9 8×22.4 254.0 215.9 8×22.4
6 168.1 279.4 241.3 8×19.0 279.4 241.3 8×22.4 279.4 241.3 8×22.4
8 218.9 342.9 298.4 8×19.0 342.9 298.4 8×22.4 342.9 298.4 8×22.4
10 273.0 406.4 362.0 12×19.0 406.4 362.0 12×25.4 406.4 362.0 12×25.4
12 323.8 482.6 431.8 12×19.0 482.6 431.8 12×25.4 482.6 431.8 12×25.4
14 355.6 533.4 476.3 12×22.4 533.4 476.2 12×28.4 533.4 476.2 12×28.4
16 406.4 596.9 539.8 16×22.4 596.9 539.8 16×28.4 596.9 539.8 16×28.4
18 457.2 635.0 577.9 16×22.4 635.0 577.8 16×31.8 635.0 577.8 16×31.8
20 508.0 698.5 635.0 20×22.4 698.5 635.0 20×31.8 698.5 635.0 20×31.8
24 609.6 812.8 749.3 20×22.4 812.8 749.3 20×35.1 812.8 749.3 20×35.1
30 762.0 984.2 914.4 28×25.4 984.2 914.4 28×35.1 ─ ─ ─
36 914.4 1,168.4 1,085.8 32×25.4 1,168.4 1,085.8 32×41.1 ─ ─ ─
42 1,066.8 1,346.2 1,257.3 36×28.4 1,346.2 1,257.3 36×41.1 ─ ─ ─
48 1,219.2 1,511.3 1,422.4 44×28.4 1,511.3 1,422.4 44×41.1 ─ ─ ─
54 1,371.6 1,682.8 1,593.8 44×28.4 ─ ─ ─ ─ ─ ─
60 1,524.0 1,854.2 1,759.0 52×31.8 ─ ─ ─ ─ ─ ─
72 1,828.8 2,197.1 2,095.5 60×31.8 ─ ─ ─ ─ ─ ─
84 2,133.6 2,533.6 2,425.7 64×35.1 ─ ─ ─ ─ ─ ─
96 2,438.4 2,876.6 2,755.9 68×35.1 ─ ─ ─ ─ ─ ─
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets,cloth reinforced rubber cut gaskets, Graseal gaskets andPTFE cut gaskets.
(2) This chart shows dimensions as per ASME B 16.21-1978Non-metallic Flat Gaskets for Pipe Flanges, converted frominches to millimeters.
(3) Applicable flanges are for ASME B 16.1 Cast Iron Flangesand ASME B 16.5 Steel Pipe Flanges.
(4) For class 25, joint sheet gaskets are not recommended.
For ASME B 16.1 FlangesFor ASME B 16.5 Flanges Soft Gasket/Flat Ring Gasket (F.R.)
65
Standard
Dim
ension Charts
Nominal Pipe
Size
Gasket inner
diameter
D1
For ASME B 16.1 Cast iron flanges For ASME B 16.5 Steel flanges
Gasket outer diameter D2
Class 25 Class 125 Class 250
Gasket outer diameter D2
Class 150 Class 300
Dimension Chart 2 Unit : A
1/2 21.3 ─ ─ ─ 47.8 53.8
3/4 26.9 ─ ─ ─ 57.2 66.5
1 33.3 ─ 66.5 73.2 66.5 73.2
11/4 42.2 ─ 76.2 82.6 76.2 82.6
11/2 48.5 ─ 85.9 95.2 85.9 95.2
2 60.5 ─ 104.6 111.3 104.6 111.3
21/2 73.2 ─ 124.0 130.0 124.0 130.0
3 88.9 ─ 136.7 149.4 136.7 149.4
31/2 101.6 ─ 162.1 165.1 162.1 165.1
4 114.3 174.8 174.8 180.8 174.8 180.8
5 141.2 200.2 196.8 215.9 196.8 215.9
6 168.1 225.6 222.2 251.0 222.2 251.0
8 218.9 282.4 279.4 307.8 279.4 307.8
10 273.0 345.9 339.9 362.0 339.9 362.0
12 323.8 416.1 409.4 422.1 409.4 422.1
14 355.6 457.2 450.8 485.6 450.8 485.6
16 406.4 520.7 514.4 539.8 514.4 539.8
18 457.2 558.8 549.1 596.9 549.1 596.9
20 508.0 616.0 606.6 654.1 606.6 654.0
24 609.6 730.2 717.6 774.7 717.6 774.7
30 762.0 892.0 882.6 952.5 ─ ─
36 914.4 1,063.8 1,047.8 1,117.6 ─ ─
42 1,066.8 1,231.9 1,219.2 1,289.0 ─ ─
48 1,219.2 1,397.0 1,384.3 1,492.2 ─ ─
54 1,371.6 1,568.4 ─ ─ ─ ─
60 1,524.0 1,730.2 ─ ─ ─ ─
72 1,828.8 2,067.1 ─ ─ ─ ─
84 2,133.6 2,394.0 ─ ─ ─ ─
96 2,438.4 2,724.2 ─ ─ ─ ─
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets,cloth reinforced rubber cut gaskets, Graseal gaskets andPTFE cut gaskets.
(2) This chart shows dimensions as per ASME B 16.21-1978,Non-metallic Flat Gaskets for Pipe Flanges, converted frominches to millimeters.
(3) Applicable flanges are for ASME B 16.1 Cast Iron Pipe Flanges andASME B 16.5 Steel Pipe Flanges.
(4) For class 25, joint sheet gaskets are not recommended.
For ASME B16.47 Series A FlangesFor MSS SP-44 Flanges Soft Gasket/Flat Ring Gasket (F.R.)
66
Sta
ndar
dD
imen
sion
Cha
rts
Nominal
Pipe Size
Gasket inner diameter
D1
Gasket outer diameter D2
Class 150 Class 300
Dimension Chart 3 Unit : A
22 558.8 660.4 704.9
26 660.4 774.7 835.2
28 711.2 831.8 898.7
30 762.0 882.6 952.5
32 812.8 939.8 1,006.3
34 863.6 990.6 1,057.1
36 914.4 1,047.8 1,117.6
38 965.2 1,111.2 1,054.1
40 1,016.0 1,162.0 1,114.6
42 1,066.8 1,219.2 1,165.4
44 1,117.6 1,276.4 1,219.2
46 1,168.4 1,327.2 1,273.0
48 1,219.2 1,384.3 1,323.8
50 1,270.0 1,435.1 1,378.0
52 1,320.8 1,492.2 1,428.8
54 1,371.6 1,549.4 1,492.2
56 1,422.4 1,606.6 1,543.0
58 1,473.2 1,663.7 1,593.8
60 1,524.0 1,714.5 1,644.6
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets, cloth reinforced rubber cut gaskets,Graseal gaskets and PTFE cut gaskets.
(2) This chart shows dimensions as per ASME B 16.21-1978, Non-metallic Flat Gaskets for PipeFlanges, converted from inches to millimeters.
(3) Applicable flanges are for ASME B 16.47 Series A and MSS SP–44.
(4) Nominal pipe size 22 for reference only. Size not listed in ASME B16.47.
For ASME B16.47 Series B FlangesFor API-605-1980 FlangesFor Taylor Forge Flanges
Soft Gasket/Flat Ring Gasket (F.R.) Group I
67
Standard
Dim
ension Charts
Nominal Pipe
Size
Raised Face Flanges Slip-on Welded Flanges
Gasket outer diameter Class 175 Class 350Gasket innerdiameterD2
Class 75D2
Class 150D2
Class 300D2
Outer diameter D2
Inner diameterD1
Inner diameterD1
Outer diameter D2
Dimension Chart 4 Unit : A
26 660.4 708.2 725.4 771.7 711 737 724 749
28 711.2 759.0 776.2 825.5 762 787 775 800
30 762.0 809.8 827.0 886.0 813 845 826 857
32 812.8 860.6 881.1 939.8 864 895 876 908
34 863.6 911.4 935.0 993.6 911 949 927 959
36 914.4 973.1 987.6 1,047.8 962 1,000 984 1,022
38 965.2 1,023.9 1,044.4 1,098.6 1,013 1,051 1,035 1,073
40 1,016.0 1,074.7 1,095.2 1,149.4 1,064 1,102 1,080 1,124
42 1,066.8 1,125.5 1,146.0 1,200.2 1,118 1,162 1,130 1,181
44 1,117.6 1,181.1 1,196.8 1,251.0 1,168 1,213 1,191 1,241
46 1,168.4 1,231.9 1,255.8 1,317.8 1,219 1,264 1,241 1,292
48 1,219.2 1,282.7 1,306.6 1,368.6 1,270 1,314 1,292 1,343
50 1,270.0 1,333.5 1,357.4 1,419.4 1,321 1,365 ─ ─
52 1,320.8 1,387.3 1,408.2 1,470.2 1,372 1,422 ─ ─
54 1,371.6 1,438.1 1,463.5 1,555.8 1,422 1,473 ─ ─
56 1,422.4 1,495.6 1,514.3 1,593.9 ─ ─ ─ ─
58 1,473.2 1,546.4 1,579.6 1,655.8 ─ ─ ─ ─
60 1,524.0 1,597.2 1,630.4 1,704.8 1,575 1,626 ─ ─
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets, cloth reinforced rubber cut gaskets,Graseal gaskets and PTFE cut gaskets.
(2) Dimensions for raised face flanges are the same as ASME B16.21-1992 but converted to millimeters from inches.
Dimensions for slip-on flanges are same as JPI-7S-16-85, Group I
(3) Applicable flanges are ASME B16.47 Series B Flanges. However, this chart can also be used for API-605-1980 and JPI-7S-43-85.
For slip-on welded flanges, applicable flanges are JPI-7S-43-85 as well as Taylor Forge flanges.
For JPI Male & Female /Tongue & Groove Flanges Soft Gasket
68
Sta
ndar
dD
imen
sion
Cha
rts
Nominal Pipe Size
Large male & female Large tongue & groove
Group I Group II Group II
InnerdiameterD1
OuterdiameterD2
InnerdiameterD1
OuterdiameterD2
InnerdiameterD1
OuterdiameterD2A B
Dimension Chart 5 Unit : A
15 1/2 22 35 25 35 25 35
20 3/4 28 43 33 43 33 43
25 1 34 51 38 51 38 51
(32) (11/4) 44 64 48 64 48 64
40 11/2 49 73 54 73 54 73
50 2 61 92 73 92 73 92
65 21/2 77 105 86 105 86 105
80 3 90 127 108 127 108 127
(90) (31/2) 103 140 121 140 121 140
100 4 116 157 132 157 132 157
(125) (5) 143 186 160 186 160 186
150 6 169 216 190 216 190 216
200 8 220 268 238 268 238 268
250 10 275 323 287 323 287 323
300 12 326 380 344 380 344 380
350 14 358 412 376 412 376 412
400 16 408 469 427 469 427 469
450 18 459 532 490 532 490 532
500 20 510 583 535 583 535 583
600 24 612 690 643 690 643 690
Notes: (1) The material used for these gaskets is mainly joint sheets.
(2) This dimension chart is the same as JPI-7S-16-98 “Dimensions for non-metallic gaskets forpipes” large male & female dimensions and large tongue & groove dimensions.
(3) Applicable flanges are JPI-7S-15-99.
(4) It is better to avoid using the nominal size values in brackets if possible.
For ASME B16.5 FlangesFor ASME B16.47 Series B Flanges VorteaxTM Gasket with Outer Ring
70
Sta
ndar
dD
imen
sion
Cha
rts
Nominal Pipe SizeClass 150 Class 300 Class 400
Gasket innerdiameterD2
Gasket outerdiameterD3
Outer ring outerdiameterD4
Gasket innerdiameterD2
Gasket outerdiameterD3
Outer ring outerdiameterD4
Gasket innerdiameterD2
Gasket outerdiameterD3
Outer ring outerdiameterD4A B
Dimension Chart 6 Unit : A
15 1/2 19.0 31.8 47.8 19.0 31.8 54.1 19.0 31.8 54.120 3/4 25.4 39.6 57.2 25.4 39.6 66.8 25.4 39.6 66.825 1 31.8 47.8 66.8 31.8 47.8 73.2 31.8 47.8 73.2(32) (11/4) 47.8 60.5 76.2 47.8 60.5 82.6 47.8 60.5 82.640 11/2 54.1 69.8 85.9 54.1 69.8 95.2 54.1 69.8 95.250 2 69.8 85.9 104.9 69.8 85.9 111.3 69.8 85.9 111.265 21/2 82.6 98.6 124.0 82.6 98.6 130.3 82.6 98.6 130.380 3 101.6 120.6 136.7 101.6 120.6 149.4 101.6 120.6 149.4(90) (31/2) 114.3 133.3 161.9 114.3 133.3 165.1 114.3 133.3 161.9100 4 127.0 149.4 174.8 127.0 149.4 181.1 120.6 149.4 177.8(125) (5) 155.7 177.8 196.8 155.7 177.8 215.9 147.6 177.8 212.9150 6 182.6 209.6 222.2 182.6 209.6 251.0 174.8 209.6 247.6200 8 233.4 263.7 279.4 233.4 263.7 308.1 225.6 263.7 304.8250 10 287.3 317.5 339.9 287.3 317.5 362.0 274.6 317.5 358.9300 12 339.9 374.6 409.7 339.9 374.6 422.4 327.2 374.6 419.1350 14 371.6 406.4 450.8 371.6 406.4 485.9 362.0 406.4 482.6400 16 422.4 463.6 514.4 422.4 463.6 539.8 412.8 463.6 536.7450 18 474.7 527.0 549.4 474.7 527.0 596.9 469.9 527.0 593.8500 20 525.5 577.8 606.6 525.5 577.8 654.0 520.7 577.8 647.7600 24 628.6 685.8 717.6 628.6 685.8 774.7 628.6 685.8 768.4650 26 673.1 698.5 725.4 673.1 711.2 771.7 666.8 698.5 746.3700 28 723.9 749.3 776.2 723.9 762.0 825.5 714.5 749.3 800.1750 30 774.7 800.1 827.0 774.7 812.8 886.0 765.3 806.4 857.2800 32 825.5 850.9 881.1 825.5 863.6 939.8 812.8 860.6 911.4850 34 876.3 908.0 935.0 876.3 914.4 993.9 866.9 911.4 962.2900 36 927.1 958.8 987.6 927.1 965.2 1,047.8 917.7 965.2 1,022.4950 38 974.6 1,009.6 1,044.7 1,009.6 1,047.8 1,098.6 971.6 1,022.4 1,073.21,000 40 1,022.4 1,063.8 1,095.5 1,060.4 1,098.6 1,149.6 1,025.6 1,076.4 1,127.21,050 42 1,079.5 1,114.6 1,146.3 1,079.5 1,117.6 1,200.2 1,076.4 1,127.2 1,178.01,100 44 1,124.0 1,165.4 1,197.1 1,162.0 1,200.2 1,251.0 1,130.3 1,181.1 1,231.91,150 46 1,181.1 1,224.0 1,255.8 1,216.2 1,254.2 1,317.8 1,193.8 1,244.6 1,289.01,200 48 1,231.9 1,270.0 1,306.6 1,231.9 1,270.0 1,368.6 1,244.6 1,295.4 1,346.2(1,250) (50) 1,282.7 1,325.6 1,357.4 1,317.8 1,355.9 1,419.4 1,295.4 1,346.2 1,403.4(1,300) (52) 1,333.5 1,376.4 1,408.2 1,368.6 1,406.7 1,470.2 1,346.2 1,397.0 1,454.21,350 54 1,384.3 1,422.4 1,463.8 1,384.3 1,422.4 1,530.4 1,403.4 1,454.2 1,517.6(1,400) (56) 1,435.1 1,470.2 1,514.6 1,479.6 1,524.0 1,593.8 1,454.2 1,505.0 1,568.4(1,450) (58) 1,485.9 1,522.5 1,579.6 1,535.2 1,573.3 1,655.8 1,505.0 1,555.8 1,619.21,500 60 1,536.7 1,573.3 1,630.4 1,536.7 1,574.8 1,706.6 1,568.4 1,619.2 1,682.8
Notes: (1) This dimension chart is the same as ASME B16.20-2000except 3-1/2” which is not listed in ASME B16.20-2000. It isalso the same as JPI-7S-41-2005.
(2) Applicable flanges are ASME B16.5 flanges and ASMEB16.47 series B flanges. However, these can also be usedfor JPI-7S-15, JPI-7S-43 series B and API-Std-605 flanges.
(3) Dimensions inside of the bold line are not suitable for slip-on welded flanges. Use weld-neck flanges or socket-weldedflanges. If slip-on flanges are used, gaskets as perdimension on page 71 are recommended.
(4) For class 900 and above, please use weld-neck flanges.
(5) For bolting materials, high-tension bolts such as B7 (SNB-7) orabove are required.
(6) With inner and outer rings is recommended for class 900, 1500 and2500. Also for 26” and above.
(7) Nominal pipe size shown in brackets shall be avoided as much aspossible.
(8) The gasket outer diameter for the types outer ring indicates theshoulder dimensions of the gasket excluding spring layers.
Standard
Dim
ension Charts
71
┃Recommended Dimensions for Slip-on Welded Flanges┃
19.0 31.8 54.1 19.0 31.8 63.5 19.0 31.8 63.5 19.0 31.8 69.8 15 1/225.4 39.6 66.8 25.4 39.6 69.8 25.4 39.6 69.8 25.4 39.6 76.2 20 3/431.8 47.8 73.2 31.8 47.8 79.5 31.8 47.8 79.5 31.8 47.8 85.9 25 147.8 60.5 82.6 39.6 60.5 88.9 39.6 60.4 88.9 39.6 60.5 104.9 (32) (11/4)54.1 69.8 95.2 47.8 69.8 98.6 47.8 69.8 98.6 47.8 69.8 117.6 40 11/269.8 85.9 111.3 58.7 85.9 143.0 58.7 85.9 143.0 58.7 85.9 146.0 50 282.6 98.6 130.3 69.8 98.6 165.1 69.8 98.6 165.1 69.8 98.6 168.4 65 21/2101.6 120.6 149.4 95.2 120.6 168.4 92.2 120.6 174.8 92.2 120.6 196.8 80 3114.3 133.3 161.9 ─ ─ ─ ─ ─ ─ ─ ─ ─ (90) (31/2)120.6 149.4 193.8 120.6 149.4 206.5 117.6 149.6 209.6 117.6 149.4 235.0 100 4147.6 177.8 241.3 147.6 177.8 247.6 143.0 177.8 254.0 143.0 177.8 279.4 (125) (5)174.8 209.6 266.7 174.8 209.6 289.1 171.4 209.6 282.7 171.4 209.6 317.5 150 6225.6 263.7 320.8 222.2 257.3 358.9 215.9 257.3 352.6 215.9 257.3 387.4 200 8274.6 317.5 400.0 276.4 311.2 435.1 266.7 311.2 435.1 270.0 311.2 476.2 250 10327.2 374.6 457.2 323.8 368.3 498.6 323.8 368.3 520.7 317.5 368.3 549.4 300 12362.0 406.4 492.2 355.6 400.0 520.7 362.0 400.0 577.8 ─ ─ ─ 350 14412.8 463.6 565.2 412.8 457.2 574.8 406.4 457.2 641.4 ─ ─ ─ 400 16469.9 527.0 612.9 463.6 520.7 638.3 463.6 520.7 704.8 ─ ─ ─ 450 18520.7 577.8 682.8 520.7 571.5 698.5 514.4 571.5 755.6 ─ ─ ─ 500 20628.6 685.8 790.7 628.6 679.4 838.2 616.0 679.4 901.7 ─ ─ ─ 600 24663.7 714.5 765.3 692.2 749.3 838.2 ─ ─ ─ ─ ─ ─ 650 26704.8 755.6 819.2 743.0 800.1 901.7 ─ ─ ─ ─ ─ ─ 700 28778.0 828.8 879.6 806.4 857.2 958.8 ─ ─ ─ ─ ─ ─ 750 30831.8 882.6 933.4 863.6 914.4 1,016.0 ─ ─ ─ ─ ─ ─ 800 32889.0 939.8 997.0 920.8 971.6 1,073.2 ─ ─ ─ ─ ─ ─ 850 34939.8 990.6 1,047.8 946.2 997.0 1,124.0 ─ ─ ─ ─ ─ ─ 900 36990.6 1,041.4 1,104.9 1,035.0 1,085.8 1,200.2 ─ ─ ─ ─ ─ ─ 950 381,047.8 1,098.6 1,155.7 1,098.6 1,149.4 1,251.0 ─ ─ ─ ─ ─ ─ 1,000 401,104.9 1,155.7 1,219.2 1,149.4 1,200.2 1,301.8 ─ ─ ─ ─ ─ ─ 1,050 421,162.0 1,212.8 1,270.0 1,206.5 1,257.3 1,368.6 ─ ─ ─ ─ ─ ─ 1,100 441,212.8 1,263.6 1,327.2 1,270.0 1,320.8 1,435.1 ─ ─ ─ ─ ─ ─ 1,150 461,270.0 1,320.8 1,390.6 1,320.8 1,371.6 1,485.9 ─ ─ ─ ─ ─ ─ 1,200 481,320.8 1,371.6 1,447.8 ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,250) (50)1,371.6 1,422.4 1,498.6 ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,300) (52)1,428.8 1,479.6 1,555.8 ─ ─ ─ ─ ─ ─ ─ ─ ─ 1,350 541,479.6 1,530.4 1,612.9 ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,400) (56)1,536.7 1,587.5 1,663.7 ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,450) (58)1,593.8 1,644.6 1,733.6 ─ ─ ─ ─ ─ ─ ─ ─ ─ 1,500 60
Class 600 Class 900 Class 1500 Class 2500
Gasket innerdiameter D2
Gasket outerdiameterD3
Outer ringouter diameterD4
Gasket innerdiameter D2
Gasket outerdiameterD3
Outer ringouter diameterD4
Gasket innerdiameter D2
Gasket outerdiameterD3
Outer ringouter diameterD4
Gasket innerdiameter D2
Gasket outerdiameterD3
Outer ringouter diameterD4 A B
Unit : A
Nominal Pipe
Size
Nominal Pipe SizeClass 150 Class 300・400・600 Class 900・1500
Gasket innerdiameterD2
Gasket outerdiameterD3
Outer ring outerdiameterD4
Gasket innerdiameterD2
Gasket outerdiameterD3
Outer ring outerdiameterD4
Gasket innerdiameterD2
Gasket outerdiameterD3
Outer ring outerdiameterD4A B
Unit : A
15 1/2 24.2 34.9 49.1 24.2 34.9 55.5 24.2 34.9 65.0
20 3/4 29.7 42.9 58.7 29.7 42.9 68.1 29.7 42.9 71.4
25 1 36.5 50.8 68.2 36.5 50.8 74.5 36.5 50.8 80.9
For ASME B16.5 FlangesFor ASME B16.47 Series B Flanges VortexTM Gasket with Inner and Outer Ring
72
Sta
ndar
dD
imen
sion
Cha
rts
Nominal Pipe SizeClass 150 Class 300 Class 400
Inner ringinnerdiameter D1
Gasketinnerdiameter D2
Gasket outerdiameter
D3
Outer ringouterdiameter D4
Inner ringinnerdiameter D1
Gasketinnerdiameter D2
Gasket outerdiameter D3
Outer ringouterdiameter D4
Inner ringinnerdiameter D1
Gasketinnerdiameter D2
Gasketouterdiameter D3
Outer ringouterdiameter D4A B
Dimension Chart 7 Unit : A
15 1/2 14.2 19.1 31.8 47.8 14.2 19.1 31.8 54.1 14.2 19.1 31.8 54.120 3/4 20.6 25.4 39.6 57.2 20.6 25.4 39.6 66.8 20.6 25.4 39.6 66.825 1 26.9 31.8 47.8 66.8 26.9 31.8 47.8 73.2 26.9 31.8 47.8 73.2(32) (11/4) 38.1 47.8 60.5 76.2 38.1 47.8 60.5 82.6 38.1 47.8 60.5 82.640 11/2 44.5 54.1 69.9 85.9 44.5 54.1 69.9 95.3 44.5 54.1 69.9 95.350 2 55.6 69.9 85.9 104.9 55.6 69.9 85.9 111.3 55.6 69.9 85.9 111.365 21/2 66.5 82.6 98.6 124.0 66.5 82.6 98.6 130.3 66.5 82.6 98.6 130.380 3 81.0 101.6 120.7 136.7 81.0 101.6 120.7 149.4 78.7 101.6 120.7 149.4(90) (31/2) 93.7 114.3 133.3 161.9 93.7 114.3 133.3 165.1 93.7 114.3 133.3 161.9100 4 106.4 127.0 149.4 174.8 106.4 127.0 149.4 181.1 102.6 120.7 149.4 177.8(125) (5) 131.8 155.7 177.8 196.9 131.8 155.7 177.8 215.9 128.3 147.6 177.8 212.9150 6 157.2 182.6 209.6 222.3 157.2 182.6 209.6 251.0 154.9 174.8 209.6 247.7200 8 215.9 233.4 263.7 279.4 215.9 233.4 263.7 308.1 205.7 225.6 263.7 304.8250 10 268.2 287.3 317.5 339.9 268.2 287.3 317.5 362.0 255.3 274.6 317.5 358.9300 12 317.5 339.9 374.7 409.7 317.5 339.9 374.7 422.4 307.3 327.2 374.7 419.1350 14 349.3 371.6 406.4 450.9 349.3 371.6 406.4 485.9 342.9 362.0 406.4 482.6400 16 400.1 422.4 463.6 514.4 400.1 422.4 463.6 539.8 389.9 412.8 463.6 536.7450 18 449.3 474.7 527.1 549.4 449.3 474.7 527.1 596.9 438.2 469.9 527.1 593.9500 20 500.1 525.5 577.9 606.6 500.1 525.5 577.9 654.1 489.0 520.7 577.9 647.7600 24 603.3 628.7 685.8 717.6 603.3 628.7 685.8 774.7 590.6 628.7 685.8 768.4650 26 654.1 673.1 698.5 725.4 654.1 673.1 711.2 771.7 654.1 666.8 698.5 746.3700 28 704.9 723.9 749.3 776.2 704.9 723.9 762.0 825.5 701.8 714.5 749.3 800.1750 30 755.7 774.7 800.1 827.0 755.7 774.7 812.8 886.0 752.6 765.3 806.5 857.3800 32 806.5 825.5 850.9 881.1 806.5 825.5 863.6 939.8 800.1 812.8 860.6 911.4850 34 857.3 876.3 908.1 935.0 857.3 876.3 914.4 993.9 850.9 866.9 911.4 962.2900 36 908.1 927.1 958.9 987.6 908.1 927.1 965.2 1,047.8 898.7 917.7 965.2 1,022.4950 38 958.9 974.6 1,009.7 1,044.7 971.6 1,009.7 1,047.8 1,098.6 952.5 971.6 1,022.4 1,073.21,000 40 1,009.7 1,022.4 1,063.8 1,095.5 1,022.4 1,060.5 1,098.6 1,149.4 1,000.3 1,025.7 1,076.5 1,127.31,050 42 1,060.5 1,079.5 1,114.6 1,146.3 1,085.9 1,111.3 1,149.4 1,200.2 1,051.1 1,076.5 1,127.3 1,178.11,100 44 1,111.3 1,124.0 1,165.4 1,197.1 1,124.0 1,162.1 1,200.2 1,251.0 1,104.9 1,130.3 1,181.1 1,231.91,150 46 1,162.1 1,181.1 1,224.0 1,255.8 1,178.1 1,216.2 1,254.3 1,317.8 1,168.4 1,193.8 1,244.6 1,289.11,200 48 1,212.9 1,231.9 1,270.0 1,306.6 1,231.9 1,263.7 1,311.4 1,368.6 1,206.5 1,244.6 1,295.4 1,346.2(1,250) (50) 1,263.7 1,282.7 1,325.6 1,357.4 1,267.0 1,317.8 1,355.9 1,419.4 1,257.3 1,295.4 1,346.2 1,403.4(1,300) (52) 1,314.5 1,333.5 1,376.4 1,408.2 1,317.8 1,368.6 1,406.7 1,470.2 1,308.1 1,346.2 1,397.0 1,454.21,350 54 1,365.3 1,384.3 1,422.4 1,463.8 1,365.3 1,403.4 1,454.2 1,530.4 1,352.6 1,403.4 1,454.2 1,517.7(1,400) (56) 1,422.4 1,444.8 1,477.8 1,514.6 1,428.8 1,479.6 1,524.0 1,593.9 1,403.4 1,454.2 1,505.0 1,568.5(1,450) (58) 1,478.0 1,500.4 1,528.8 1,579.6 1,484.4 1,535.2 1,573.3 1,655.8 1,454.2 1,505.0 1,555.8 1,619.31,500 60 1,535.2 1,557.3 1,586.0 1,630.4 1,557.3 1,589.0 1,630.4 1,706.6 1,517.7 1,568.5 1,619.3 1,682.8
Notes: (1) This dimension chart is the same as ASME B16.20-1998except 3-1/2” which is not listed in ASME B16.20-1998. It isalso the same as JPI-7S-41-2005.
(2) Applicable flanges are ASME B16.5 flanges and ASMEB16.47 series B flanges. However, these can also be usedfor JPI-7S-15, JPI-7S-43 series B and API-Std-605 flanges.
(3) Dimensions inside of the bold line are not suitable for slip-on welded flanges. Use weld-neck flanges or socket-weldedflanges. If slip-on flanges are used, gaskets as perdimension on page 73 are recommended.
(4) For class 900 and above, please use weld-neck flanges.
(5) For bolting materials, high-tension bolts such as B7 (SNB-7) orabove are required.
(6) When used for slip-on flanges, please pay attention to thedimensions since the inner diameter of inner ring may be smallerthan the flange inner diameter. To avoid this kind of problem, weld-neck flanges are recommended.
(7) The gasket outer diameter for the types inner ring indicates theshoulder dimensions of the gasket excluding spring layers.
Standard
Dim
ension Charts
73
Inner ringinnerdiameterD1
Gasketinnerdiameter D2
Gasketouterdiameter D3
Outer ringouterdiameterD4
Inner ringinnerdiameterD1
Gasketinnerdiameter D2
Gasketouterdiameter D3
Outer ringouterdiameterD4
Inner ringinnerdiameterD1
Gasketinnerdiameter D2
Gasketouterdiameter D3
Outer ringouterdiameterD4
Inner ringinnerdiameterD1
Gasketinnerdiameter D2
Gasketouterdiameter D3
Outer ringouterdiameterD4
┃Recommended Dimensions for Slip-on Welded Flanges┃
14.2 19.1 31.8 54.1 14.2 19.1 31.8 63.5 14.2 19.1 31.8 63.5 14.2 19.1 31.8 69.9 15 1/220.6 25.4 39.6 66.8 20.6 25.4 39.6 69.9 20.6 25.4 39.6 69.9 20.6 25.4 39.6 76.2 20 3/426.9 31.8 47.8 73.2 26.9 31.8 47.8 79.5 26.9 31.8 47.8 79.5 26.9 31.8 47.8 85.9 25 138.1 47.8 60.5 82.6 33.3 39.6 60.5 88.9 33.3 39.6 60.5 88.9 33.3 39.6 60.5 104.9 (32) (11/4)44.5 54.1 69.9 95.3 41.4 47.8 69.9 98.6 41.4 47.8 69.9 98.6 41.4 47.8 69.9 117.6 40 11/255.6 69.9 85.9 111.3 52.3 58.7 85.9 143.0 52.3 58.7 85.9 143.0 52.3 58.7 85.9 146.1 50 266.5 82.6 98.6 130.3 63.5 69.9 98.6 165.1 63.5 69.9 98.6 165.1 63.5 69.9 98.6 168.4 65 21/278.7 101.6 120.7 149.4 78.7 95.3 120.7 168.4 78.7 92.2 120.7 174.8 78.7 92.2 120.7 196.9 80 393.7 114.3 133.3 161.9 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ (90) (31/2)102.6 120.7 149.4 193.8 102.6 120.7 149.4 206.5 97.8 117.6 149.4 209.6 97.8 117.6 149.4 235.0 100 4128.3 147.6 177.8 241.3 128.3 147.6 177.8 247.7 124.5 143.0 177.8 254.0 124.5 143.0 177.8 279.4 (125) (5)154.9 174.8 209.6 266.7 154.9 174.8 209.6 289.1 147.3 171.5 209.6 282.7 147.3 171.5 209.6 317.5 150 6205.7 225.6 263.7 320.8 196.9 222.3 257.3 358.9 196.9 215.9 257.3 352.6 196.9 215.9 257.3 387.4 200 8255.3 274.6 317.5 400.1 246.1 276.4 311.2 435.1 246.1 266.7 311.2 435.1 246.1 270.0 311.2 476.3 250 10307.3 327.2 374.7 457.2 292.1 323.9 368.3 498.6 292.1 323.9 368.3 520.7 292.1 317.5 368.3 549.4 300 12342.9 362.0 406.4 492.3 320.8 355.6 400.1 520.7 320.8 362.0 400.1 577.9 ─ ─ ─ ─ 350 14389.9 412.8 463.6 565.2 374.7 412.8 457.2 574.8 368.3 406.4 457.2 641.4 ─ ─ ─ ─ 400 16438.2 469.9 527.1 612.9 425.5 463.6 520.7 638.3 425.5 463.6 520.7 704.9 ─ ─ ─ ─ 450 18489.0 520.7 577.9 682.8 482.6 520.7 571.5 698.5 476.3 514.4 571.5 755.7 ─ ─ ─ ─ 500 20590.6 628.7 685.8 790.7 590.6 628.7 679.5 838.2 577.9 616.0 679.5 901.7 ─ ─ ─ ─ 600 24644.7 663.7 714.5 765.3 666.8 692.2 749.3 838.2 ─ ─ ─ ─ ─ ─ ─ ─ 650 26685.8 704.9 755.7 819.2 717.6 743.0 800.1 901.7 ─ ─ ─ ─ ─ ─ ─ ─ 700 28752.6 778.0 828.8 879.6 781.1 806.5 857.3 958.9 ─ ─ ─ ─ ─ ─ ─ ─ 750 30793.8 831.9 882.7 933.5 838.2 863.6 914.4 1,016.0 ─ ─ ─ ─ ─ ─ ─ ─ 800 32850.9 889.0 939.8 997.0 895.4 920.8 971.6 1,073.2 ─ ─ ─ ─ ─ ─ ─ ─ 850 34901.7 939.8 990.6 1,047.8 920.8 946.2 997.0 1,124.0 ─ ─ ─ ─ ─ ─ ─ ─ 900 36952.5 990.6 1,041.4 1,104.9 1,009.7 1,035.1 1,085.9 1,200.2 ─ ─ ─ ─ ─ ─ ─ ─ 950 381,009.7 1,047.8 1,098.6 1,155.7 1,060.5 1,098.6 1,149.4 1,251.0 ─ ─ ─ ─ ─ ─ ─ ─ 1,000 401,066.8 1,104.9 1,155.7 1,219.2 1,111.3 1,149.4 1,200.2 1,301.8 ─ ─ ─ ─ ─ ─ ─ ─ 1,050 421,111.3 1,162.1 1,212.9 1,270.0 1,155.7 1,206.5 1,257.3 1,368.6 ─ ─ ─ ─ ─ ─ ─ ─ 1,100 441,162.1 1,212.9 1,263.7 1,327.2 1,219.2 1,270.0 1,320.8 1,435.1 ─ ─ ─ ─ ─ ─ ─ ─ 1,150 461,219.2 1,270.0 1,320.8 1,390.7 1,270.0 1,320.8 1,371.6 1,485.9 ─ ─ ─ ─ ─ ─ ─ ─ 1,200 481,270.0 1,320.8 1,371.6 1,447.8 ─ ─ ─ ─ ─ ── ─ ─ ─ ─ ─ (1,250) (50)1,320.8 1,371.6 1,422.4 1,498.6 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,300) (52)1,378.0 1,428.8 1,479.6 1,555.8 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ 1,350 541,428.8 1,479.6 1,530.4 1,612.9 ─ ─ ─ ─ ── ─ ─ ─ ─ ─ ─ (1,400) (56)1,473.2 1,536.7 1,587.5 1,663.7 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ (1,450) (58)1,530.4 1,593.9 1,644.7 1,733.6 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ 1,500 60
Class 600 Class 900 Class 1500 Class 2500
A B
Unit : A
Nominal Pipe
Size
Nominal Pipe SizeClass 150 Class 300・400・600 Class 900・1500
A B
Unit : A
15 1/2 18.2 24.2 34.9 49.1 18.2 24.2 34.9 55.5 18.2 24.2 34.9 65.0
20 3/4 23.0 29.7 42.9 58.7 23.0 29.7 42.9 68.1 23.0 29.7 42.9 71.4
25 1 30.0 36.5 50.8 68.2 30.0 36.5 50.8 74.5 30.0 36.5 50.8 80.9
Inner ringinnerdiameterD1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ringouterdiameterD4
Inner ringinnerdiameterD1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ringouterdiameterD4
Inner ringinnerdiameterD1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ringouterdiameterD4
For ASME B16.47 Series A FlangesFor MSS-SP-44 Flanges VortexTM Gasket with Inner and Outer Ring
74
Sta
ndar
dD
imen
sion
Cha
rts
Nominal
Pipe Size
Class 300Class 150
Dimension Chart 8 Unit : A
26 654.1 673.1 704.9 774.7 654.1 685.8 736.6 835.2
28 704.9 723.9 755.7 831.9 704.9 736.6 787.4 898.7
30 755.7 774.7 806.5 882.7 755.7 793.8 844.6 952.5
32 806.5 825.5 860.6 939.8 806.5 850.9 901.7 1,006.6
34 857.3 876.3 911.4 990.6 857.3 901.7 952.5 1,057.4
36 908.1 927.1 968.5 1,047.8 908.1 955.8 1,006.6 1,117.6
38 958.9 977.9 1,019.3 1,111.3 952.5 977.9 1,016.0 1,054.1
40 1,009.7 1,028.7 1,070.1 1,162.1 1,003.3 1,022.4 1,070.1 1,114.6
42 1,060.5 1,079.5 1,124.0 1,219.2 1,054.1 1,073.2 1,120.9 1,165.4
44 1,111.3 1,130.3 1,178.1 1,276.4 1,104.9 1,130.3 1,181.1 1,219.2
46 1,162.1 1,181.1 1,228.9 1,327.2 1,152.7 1,178.1 1,228.9 1,273.3
48 1,212.9 1,231.9 1,279.7 1,384.3 1,209.8 1,235.2 1,286.0 1,324.1
50 1,263.7 1,282.7 1,333.5 1,435.1 1,244.6 1,295.4 1,346.2 1,378.0
52 1,314.5 1,333.5 1,384.3 1,492.3 1,320.8 1,346.2 1,397.0 1,428.8
54 1,358.9 1,384.3 1,435.1 1,549.4 1,352.6 1,403.4 1,454.2 1,492.3
56 1,409.7 1,435.1 1,485.9 1,606.6 1,403.4 1,454.2 1,505.0 1,543.1
58 1,460.5 1,485.9 1,536.7 1,663.7 1,447.8 1,511.3 1,562.1 1,593.9
60 1,511.3 1,536.7 1,587.5 1,714.5 1,524.0 1,562.1 1,612.9 1,644.7
Notes: (1) This dimension chart is the same as the dimensions ofASME B16.20-1998.
(2) Applicable flanges are ANSI/ASME B16.47 Series A andMSS-SP-44 flanges. This can also be used for JPI-7S-43Series A flanges.
(3) Please use weld-neck flanges.
(4) The gasket outer diameter for the types inner ring indicates theshoulder dimensions of the gasket excluding spring layers.
Inner ring inner diameter
D1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ring outerdiameter D4
Inner ring inner diameter
D1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ring outerdiameter D4
Nominal
Pipe Size
Class 900Class 400 Class 600
Inner ring inner diameter D1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ringouter diameter D4
Inner ring inner diameter D1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ringouter diameter D4
Inner ring inner diameter D1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ringouter diameter D4
26 660.4 685.8 736.6 831.9 647.7 685.8 736.6 866.9 660.4 685.8 736.6 882.7
28 711.2 736.6 787.4 892.3 698.5 736.6 787.4 914.4 711.2 736.6 787.4 946.2
30 755.7 793.8 844.6 946.2 755.7 793.8 844.6 971.6 768.4 793.8 844.6 1,009.7
32 812.8 850.9 901.7 1,003.3 812.8 850.9 901.7 1,022.4 812.8 850.9 901.7 1,073.2
34 863.6 901.7 952.5 1,054.1 863.6 901.7 952.5 1,073.2 863.6 901.7 952.5 1,136.7
36 917.7 955.8 1,006.6 1,117.6 917.7 955.8 1,006.6 1,130.3 920.8 958.8 1,009.7 1,200.2
38 952.5 971.6 1,022.4 1,073.2 952.5 990.6 1,041.4 1,104.9 1,009.7 1,035.1 1,085.9 1,200.2
40 1,000.3 1,025.7 1,076.5 1,127.3 1,009.7 1,047.8 1,098.6 1,155.7 1,060.5 1,098.6 1,149.4 1,251.0
42 1,051.1 1,076.5 1,127.3 1,178.1 1,066.8 1,104.9 1,155.7 1,219.2 1,111.3 1,149.4 1,200.2 1,301.8
44 1,104.9 1,130.3 1,181.1 1,231.9 1,111.3 1,162.1 1,212.9 1,270.0 1,155.7 1,206.5 1,257.3 1,368.6
46 1,168.4 1,193.8 1,244.6 1,289.1 1,162.1 1,212.9 1,263.7 1,327.2 1,219.2 1,270.0 1,320.8 1,435.1
48 1,206.5 1,244.6 1,295.4 1,346.2 1,219.2 1,270.0 1,320.8 1,390.7 1,270.0 1,320.8 1,371.6 1,485.9
50 1,257.3 1,295.4 1,346.2 1,403.4 1,270.0 1,320.8 1,371.6 1,447.8 ─ ─ ─ ─
52 1,308.1 1,346.2 1,397.0 1,454.2 1,320.8 1,371.6 1,422.4 1,498.6 ─ ─ ─ ─
54 1,352.6 1,403.4 1,454.2 1,517.7 1,378.0 1,428.8 1,479.6 1,555.8 ─ ─ ─ ─
56 1,403.4 1,454.2 1,505.0 1,568.5 1,428.8 1,479.6 1,530.4 1,612.9 ─ ─ ─ ─
58 1,454.2 1,505.0 1,555.8 1,619.3 1,473.2 1,536.7 1,587.5 1,663.7 ─ ─ ─ ─
60 1,517.7 1,568.5 1,619.3 1,682.8 1,530.4 1,593.9 1,644.7 1,733.6 ─ ─ ─ ─
For ASME B16.5 FlangesFor JPI-7S-15 Flanges VortexTM Gasket Standard Type/ With Inner Ring Type
75
Standard
Dim
ension Charts
Dimension Chart 9 Unit : A
Notes: (1) *Small: For small male & female faces or small tongue &groove face flanges.
*Large: For large male & female faces or large tongue &groove face flanges.
(2) Applicable flanges are ASME B16.5 and JPI-7S-15.
Depth of the face is preferably more than 5.5A.
(3) No large M&F and large T&G face are stipulated for class150 flanges.
(4) For small M&F and small T&G faces, Vortex gaskets are notadvisable due to its narrow gasket width. This chart ismerely for reference.
(5) The dimensions for large M&F and large T&G faces in thischart are the same as JPI-7S-41-90. The dimensions forsmall M&F and small T&G faces are the same as thedimensions shown in commentary part of JPI-7S-41-85.
(6) For large M&F faces of class 900 and above, with inner ringtype is recommended irrespective of the filler material.
(7) For small M&F faces, with inner ring type is recommendedirrespective of the filler material.
(8) For bolting materials, high-tension bolts such as B7 (SNB7) or aboveare required.
Nominal Pipe SizeInner ring inner diameter
D1Gasket inner
diameter
D2
Gasket outer diameter
D3
A B 150・300 400・600 900 1500 2500 Small * Large *
15 1/2 14.2 14.2 14.2 14.2 14.2 25.1 35.3 35.4
20 3/4 20.6 20.6 20.6 20.6 20.6 33.0 43.2 43.2
25 1 26.9 26.9 26.9 26.9 26.9 37.8 48.0 51.1
32 11/4 38.1 38.1 33.3 33.3 33.3 47.2 57.5 63.8
40 11/2 44.4 44.4 41.4 41.4 41.4 53.5 63.9 73.5
50 2 55.6 55.6 52.3 52.3 52.3 72.6 82.9 92.5
65 21/2 66.5 66.5 63.5 63.5 63.5 85.3 95.6 105.2
80 3 81.0 81.0 81.0 81.0 81.0 107.6 117.9 127.3
90 31/2 93.7 93.7 ─ ─ ─ 120.3 130.6 140.0
100 4 106.4 106.4 106.4 106.4 106.4 131.2 144.8 157.6
125 5 131.8 131.8 131.8 131.8 131.8 160.0 173.4 186.3
150 6 157.2 157.2 157.2 157.2 157.2 190.2 203.6 216.3
200 8 215.9 209.6 209.6 206.2 200.2 237.7 254.1 270.0
250 10 268.2 260.4 260.4 257.8 247.6 285.7 304.9 323.9
300 12 317.5 317.5 314.5 314.5 292.1 342.9 362.0 381.0
350 14 349.2 349.2 342.9 339.8 ─ 374.6 393.8 412.8
400 16 400.0 400.0 393.7 387.4 ─ 425.4 447.8 469.9
450 18 449.3 449.3 444.5 438.2 ─ 488.9 511.3 533.4
500 20 500.1 500.1 495.3 489.0 ─ 533.4 558.9 584.2
600 24 603.2 603.2 603.2 577.8 ─ 641.8 666.3 691.7
Tongue & Groove Male & Female
For Taylor Forge andLadish Flanges VortexTM Gasket with Inner and Outer Ring
76
Sta
ndar
dD
imen
sion
Cha
rts
Nominal Pipe
SizeLadish Class 300Ladish Class 150
Taylor Forge Class 350Taylor Forge Class 175
Dimension Chart 10 Unit : A
26 660 680 703 740 660 680 712 752
28 711 731 754 791 711 731 763 803
30 762 782 809 848 762 782 814 860
32 813 833 860 899 813 833 865 911
34 864 884 915 952 864 884 916 962
36 914 934 965 1,003 914 934 966 1,026
38 965 985 1,016 1,054 965 985 1,017 1,076
40 1,016 1,041 1,074 1,105 1,016 1,041 1,081 1,127
42 1,067 1,092 1,130 1,165 1,067 1,092 1,132 1,184
44 1,118 1,143 1,181 1,216 1,118 1,143 1,183 1,245
46 1,168 1,193 1,231 1,267 1,168 1,193 1,233 1,295
48 1,219 1,244 1,282 1,318 1,219 1,244 1,284 1,346
50 1,270 1,295 1,333 1,368 ─ ─ ─ ─
52 1,321 1,346 1,386 1,426 1,321 1,351 1,401 1,457
54 1,372 1,397 1,437 1,476 1,372 1,402 1,452 1,508
60 1,524 1,549 1,589 1,629 1,524 1,554 1,604 1,661
66 1,676 1,706 1,746 1,781 1,702 1,742 1,782 1,842
72 1,829 1,859 1,899 1,946 1,854 1,894 1,934 1,994
84 2,162 2,202 2,232 2,292 2,197 2,237 2,267 2,327
96 2,467 2,507 2,537 2,597 2,512 2,552 2,582 2,642
Inner ring inner diameter
D1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ring outerdiameter D4
Inner ring inner diameter
D1
Gasket innerdiameter D2
Gasket outerdiameter D3
Outer ring outerdiameter D4
Notes: (1) Applicable flanges are Taylor Forge Class 175, 350, 125 and 250, Ladish Class 150 and 300.For Taylor Forge Class 150, please use Standard Dimension Chart 8.
(2) These dimension were designed by NICHIAS Corporation.
(3) Gaskets with inner and outer rings are recommended for all nominal pressures.
(4) For bolting materials, high-tension bolts such as B7 (SNB-7) or above are required.
Standard
Dim
ension Charts
77
Taylor Forge Class 250Taylor Forge Class 125
650 675 725 774 650 675 725 831
701 726 776 831 701 726 776 895
752 777 827 882 752 777 827 952
803 828 878 939 803 828 878 1,009
854 879 929 990 854 879 929 1,060
904 929 979 1,047 904 929 979 1,117
955 985 1,035 1,111 955 985 1,035 1,168
1,006 1,036 1,086 1,162 1,006 1,036 1,086 1,225
1,057 1,087 1,137 1,219 1,057 1,087 1,137 1,289
1,108 1,138 1,188 1,276 1,108 1,138 1,188 1,346
1,158 1,188 1,238 1,327 1,158 1,188 1,238 1,403
1,209 1,239 1,289 1,384 1,209 1,239 1,289 1,492
1,260 1,290 1,340 1,435 ─ ─ ─ ─
1,311 1,341 1,391 1,492 ─ ─ ─ ─
1,362 1,392 1,442 1,549 ─ ─ ─ ─
1,514 1,544 1,594 1,714 ─ ─ ─ ─
1,745 1,785 1,825 1,885 ─ ─ ─ ─
1,911 1,951 1,991 2,051 ─ ─ ─ ─
2,244 2,284 2,314 2,374 ─ ─ ─ ─
2,568 2,608 2,638 2,698 ─ ─ ─ ─
Inner ring inner diameter
D1
Gasket innerdiameter D2
Gasket outer diameter D3
Outer ring outerdiameter D4
Inner ring inner diameter
D1
Gasket innerdiameter D2
Gasket outer diameter D3
Outer ring outerdiameter D4
Ring Joint Gaskets R Rings
78
Sta
ndar
dD
imen
sion
Cha
rts
Dimension Chart 11 Ring Joint Gasket Standard Dimensions Unit : A
Ring Number Pitch diameter of ring
P
Gasket Dimensions
Width of ring
W Oval
Height of ring T
Octagonal
Width of flat onOctagonal Ring
A
R-11 34.13 6.35 11.2 9.7 4.32R-12 39.69 7.92 14.2 12.7 5.23R-13 42.88 7.92 14.2 12.7 5.23R-14 44.45 7.92 14.2 12.7 5.23R-15 47.62 7.92 14.2 12.7 5.23R-16 50.80 7.92 14.2 12.7 5.23R-17 57.15 7.92 14.2 12.7 5.23R-18 60.32 7.92 14.2 12.7 5.23R-19 65.07 7.92 14.2 12.7 5.23R-20 68.28 7.92 14.2 12.7 5.23R-21 72.24 11.13 17.5 15.7 7.75R-22 82.55 7.92 14.2 12.7 5.23R-23 82.55 11.13 17.5 15.7 7.75R-24 95.25 11.13 17.5 15.7 7.75R-25 101.60 7.92 14.2 12.7 5.23R-26 101.60 11.13 17.5 15.7 7.75R-27 107.95 11.13 17.5 15.7 7.75R-28 111.12 12.70 19.0 17.5 8.66R-29 114.30 7.92 14.2 12.7 5.23R-30 117.48 11.13 17.5 15.7 7.75R-31 123.82 11.13 17.5 15.7 7.75R-32 127.00 12.70 19.0 17.5 8.66R-33 131.78 7.92 14.2 12.7 5.23R-34 131.78 11.13 17.5 15.7 7.75R-35 136.52 11.13 17.5 15.7 7.75R-36 149.22 7.92 14.2 12.7 5.23R-37 149.22 11.13 17.5 15.7 7.75R-38 157.18 15.88 22.4 20.6 10.49R-39 161.92 11.13 17.5 15.7 7.75R-40 171.45 7.92 14.2 12.7 5.23R-41 180.98 11.13 17.5 15.7 7.75R-42 190.50 19.05 25.4 23.9 12.32R-43 193.68 7.92 14.2 12.7 5.23R-44 193.68 11.13 17.5 15.7 7.75R-45 211.12 11.13 17.5 15.7 7.75R-46 211.12 12.70 19.0 17.5 8.66R-47 228.60 19.05 25.4 23.9 12.32R-48 247.65 7.92 14.2 12.7 5.23R-49 269.88 11.13 17.5 15.7 7.75R-50 269.88 15.88 22.4 20.6 10.49R-51 279.40 22.22 28.4 26.9 14.81R-52 304.80 7.92 14.2 12.7 5.23
Oval type Octagonal type
R1: When W is a 22.2250A or under, R1 is 1.59A
R1: When W is a 25.400A or under, R1 is 2.38A
Standard
Dim
ension Charts
79
Notes: (1) This chart uses the same dimensions as ASME B16.20. It is also same as JPI-7S-1998.
(2) Applicable flanges
ASME B16.5
API Spec. 6A
MSS SP-44
JPI-7S-43
JPI-7S-15
Ring Number Pitch diameter of ring
P
Gasket Dimensions
Width of ring
W Oval
Height of ring T
Octagonal
Width of flat onOctagonal Ring
A
R- 53 323.85 11.13 17.5 15.7 7.75R- 54 323.85 15.88 22.4 20.6 10.49R- 55 342.90 28.58 36.6 35.1 19.81R- 56 381.00 7.94 14.2 12.7 5.23R- 57 381.00 11.13 17.5 15.7 7.75R- 58 381.00 22.22 28.4 26.9 14.81R- 59 396.88 7.92 14.2 12.7 5.23R- 60 406.40 31.75 39.6 38.1 22.33R- 61 419.10 11.13 17.5 15.7 7.75R- 62 419.10 15.88 22.4 20.6 10.49R- 63 419.10 25.40 33.3 31.8 17.30R- 64 454.02 7.92 14.2 12.7 5.23R- 65 469.90 11.13 17.5 15.7 7.75R- 66 469.90 15.88 22.4 20.6 10.49R- 67 469.90 28.58 36.6 35.1 19.81R- 68 517.52 7.92 14.2 12.7 5.23R- 69 533.40 11.13 17.5 15.7 7.75R- 70 533.40 19.05 25.4 23.9 12.32R- 71 533.40 28.58 36.6 35.1 19.81R- 72 558.80 7.92 14.2 12.7 5.23R- 73 584.20 12.70 19.0 17.5 8.66R- 74 584.20 19.05 25.4 23.9 12.32R- 75 584.20 31.75 39.6 38.1 22.23R- 76 673.10 7.92 14.2 12.7 5.23R- 77 692.15 15.88 22.4 20.6 10.49R- 78 692.15 25.40 33.3 31.8 17.30R- 79 692.15 34.92 44.4 41.1 24.82R- 80 615.95 7.92 ─ 12.7 5.23R- 81 635.00 14.27 ─ 19.0 9.58R- 82 57.15 11.13 ─ 15.7 7.75R- 84 63.50 11.13 ─ 15.7 7.75R- 85 79.38 12.70 ─ 17.5 8.66R- 86 90.47 15.88 ─ 20.6 10.49R- 87 100.03 15.88 ─ 20.6 10.49R- 88 123.82 19.05 ─ 23.9 12.32R- 89 114.30 19.05 ─ 23.9 12.32R- 90 155.58 22.22 ─ 26.9 14.81R- 91 260.35 31.75 ─ 38.1 22.33R- 92 228.60 11.13 17.5 15.7 7.75R- 93 749.30 19.05 ─ 23.9 12.32R- 94 800.10 19.05 ─ 23.9 12.32R- 95 857.25 19.05 ─ 23.9 12.32R- 96 914.40 22.22 ─ 26.9 14.81R- 97 965.20 22.22 ─ 26.9 14.81R- 98 1,022.35 22.22 ─ 26.9 14.81R- 99 234.95 11.13 ─ 15.7 7.75R-100 749.30 28.58 ─ 35.1 19.81R-101 800.10 31.75 ─ 38.1 22.33R-102 857.25 31.75 ─ 38.1 22.33R-103 914.40 31.75 ─ 38.1 22.33R-104 965.20 34.92 ─ 41.1 24.82R-105 1,022.35 34.92 ─ 41.1 24.82
Ring Joint Gaskets API RX Rings
80
Sta
ndar
dD
imen
sion
Cha
rts
Dimension Chart 12 API RX Ring Joint Dimension Chart Unit : A
Ring NumberOutside Diameter of
RingOD
Width ofRingA
Width ofFlatC
Height ofOutside Bevel
D
Height of RingH
Radius of RingR1
Hole Sizeφd
RX- 20 76.20 8.73 4.62 3.18 19.05 1.5RX- 23 93.27 11.91 6.45 4.24 25.40 1.5RX- 24 105.97 11.91 6.45 4.24 25.40 1.5RX- 25 109.54 8.73 4.62 3.18 19.05 1.5RX- 26 111.92 11.91 6.45 4.24 25.40 1.5RX- 27 118.27 11.91 6.45 4.24 25.40 1.5RX- 31 134.54 11.91 6.45 4.24 25.40 1.5RX- 35 147.24 11.91 6.45 4.24 25.40 1.5RX- 37 159.94 11.91 6.45 4.24 25.40 1.5RX- 39 172.64 11.91 6.45 4.24 25.40 1.5RX- 41 191.69 11.91 6.45 4.24 25.40 1.5RX- 44 204.39 11.91 6.45 4.24 25.40 1.5RX- 45 221.85 11.91 6.45 4.24 25.40 1.5RX- 46 222.25 13.49 6.68 4.78 28.58 1.5RX- 47 245.27 19.84 10.33 6.88 41.28 2.3RX- 49 280.59 11.91 6.45 4.24 25.40 1.5RX- 50 283.37 16.67 8.51 5.28 31.75 1.5RX- 53 334.57 11.91 6.45 4.24 25.40 1.5RX- 54 337.34 16.67 8.51 5.28 31.75 1.5RX- 57 391.72 11.91 6.45 4.24 25.40 1.5RX- 63 441.72 26.99 14.78 8.46 50.80 2.3RX- 65 480.62 11.91 6.45 4.24 25.40 1.5RX- 66 483.39 16.67 8.51 5.28 31.75 1.5RX- 69 544.12 11.91 6.45 4.24 25.40 1.5RX- 70 550.07 19.84 10.34 6.88 41.28 2.3RX- 73 596.11 13.49 6.68 5.28 31.75 1.5RX- 74 600.87 19.84 10.34 6.88 41.28 2.3RX- 82 67.87 11.91 6.45 4.24 25.40 1.5 1.5RX- 84 74.22 11.91 6.45 4.24 25.40 1.5 1.5RX- 85 90.09 13.49 6.68 4.24 25.40 1.5 1.5RX- 86 103.58 15.08 8.51 4.78 28.58 1.5 1.5RX- 87 113.11 15.08 8.51 4.78 28.58 1.5 1.5RX- 88 139.30 17.46 10.34 5.28 31.75 1.5 3.0RX- 89 129.78 18.26 10.34 5.28 31.75 1.5 3.0RX- 90 174.63 19.84 12.17 7.42 44.45 2.3 3.0RX- 91 286.94 30.16 19.81 7.54 45.24 2.3 3.0RX- 99 245.67 11.91 6.45 4.24 25.40 1.5 *2RX-201 51.46 5.74 3.20 1.45 11.30 0.5 *2RX-205 62.31 5.56 3.05 1.83 *1 11.10 0.5 *2RX-210 97.63 9.53 5.41 3.18 *1 19.05 0.8 *2RX-215 140.89 11.91 5.33 4.24 *1 25.40 1.5 *2
Dimension Tolerance
O D +0.50-0.00
A,H +0.20-0.00
C +0.15-0.00
D +0.00-0.80
R1 ±0.50
Notes: (1) This dimension chart is the same as the dimensions of API-Spec.6A RX Pressure Energized Ring Joint Gaskets.
(2) Applicable flanges are API-Spec. 6A Wellhead Equipment 6BFlanges.
(3) Rings RX-82 through RX-91 only require one pressure passage
hole as illustrated. The centerline of the hole shall be located at the midpointof dimension C
(4) The finish of the seal surface of the gaskets is over 63RMS.
* 1 Dimensional tolerance +0, -0.38 * 2 Dimensional tolerance +0.5, -0
Ring Joint Gaskets API BX Rings
81
Standard
Dim
ension Charts
Dimension Chart 13 API BX Ring Joint Dimension Chart Unit : A
Ring
Number
Gasket Dimensions Groove Dimensions
Outside Diameterof RingOD
Height of RingH
Width of RingA
Outside Diameter of FlatODT
Width of FlatC
Depth
E
Outer Diameter G
Width
NR
Hole Sizeφd
BX-150 72.19 9.30 9.30 70.87 7.98 1.59 5.56 73.48 11.43
BX-151 76.40 9.63 9.63 75.03 8.26 1.59 5.56 77.79 11.84
BX-152 84.68 10.24 10.24 83.24 8.79 1.59 5.95 86.23 12.65
BX-153 100.94 11.38 11.38 99.31 9.78 1.59 6.75 102.77 14.07
BX-154 116.84 12.40 12.40 115.09 10.64 1.59 7.54 119.00 15.39
BX-155 147.96 14.22 14.22 145.95 12.22 1.59 8.33 150.62 17.73
BX-169 173.51 15.85 12.93 171.27 10.69 1.59 9.53 176.66 16.92
BX-156 237.92 18.62 18.62 235.28 15.98 3.18 11.11 241.83 23.39
BX-157 294.46 20.98 20.98 291.49 18.01 3.18 12.70 299.06 26.39
BX-158 352.04 23.14 23.14 348.77 19.86 3.18 14.29 357.23 29.18
BX-159 426.72 25.70 25.70 423.09 22.07 3.18 15.88 432.64 32.49
BX-160 402.59 23.83 13.74 399.21 10.36 3.18 14.29 408.00 19.96
BX-161 491.41 28.07 16.21 487.45 12.24 3.18 17.07 497.94 23.62
BX-162 475.49 14.22 14.22 473.48 12.22 1.59 8.33 478.33 17.91
BX-163 556.16 30.10 17.37 551.89 13.11 3.18 18.26 563.50 25.55
BX-164 570.56 30.10 24.59 566.29 20.32 3.18 18.26 577.90 32.77
BX-165 624.71 32.03 18.49 620.19 13.97 3.18 19.05 632.56 27.20
BX-166 640.03 32.03 26.14 635.51 21.62 3.18 19.05 647.88 34.87
BX-167 759.36 35.87 13.11 754.28 8.03 1.59 21.43 768.33 22.91
BX-168 765.25 35.87 16.05 760.17 10.97 1.59 21.43 774.22 25.86
Dimension Tolerance
OD +0.50-0.15
H,A +0.20-0
ODT ±0.05-0
C +0.15-0
E +0.50-0
G.N +0.10-0.0
Notes: (1) This dimension chart is the same as the dimensions of API-Spec. 6A 1977 BX Pressure Energized Ring-Joint Gaskets.
(2) Applicable flanges are API-Spec. 6A Wellhead Equipment 6BX Flanges.
(3) One pressure passage hole is required per gasket as illustrated.
The centerline of the hole shall be located at the midpoint of dimension C
(4) The finish of the seal surface of the gaskets is over 32RMS.
Radius R shall be 8 ~12% of gasket height H
Ring Joint Gaskets Correspondence of ring number, flange NPS and class
82
Sta
ndar
dD
imen
sion
Cha
rts
Nominal
Pipe
Size
Applicable flanges
JPI - 7 - 15, ANSI B 16.5
Class 150 300・400・600 900 1500 2500 960 2000 3000 5000 300・400・600 900
API Spec 6A MSS SP - 44
Dimension Chart 14 Unit : A
1/2B ─ R11 R12 R12 R13 ─ ─ ─ ─ ─ ─
3/4 ─ R13 R14 R14 R16 ─ ─ ─ ─ ─ ─
1 R15 R16 R16 R16 R18 ─ ─ ─ ─ ─ ─
11/4 R17 R16 R18 R18 R21 ─ ─ ─ ─ ─ ─
11/2 R19 R20 R20 R20 R23 ─ R20 R20 R20 ─ ─
2 R22 R23 R24 R24 R26 ─ R23 R24 R24 ─ ─
21/2 R25 R26 R27 R27 R28 ─ R26 R27 R27 ─ ─
3 R29 R30(1) R31 R35 R32 ─ R31 R31 R35 ─ ─
31/2 R33 R34 ─ ─ ─ ─ ─ ─ ─ ─ ─
4 R36 R37 R37 R39 R38 ─ R37 R37 R39 ─ ─
5 R40 R41 R41 R44 R42 ─ R41 R41 ─ ─ ─
6 R43 R45 R45 R46 R47 R45 R45 R45 R46 ─ ─
8 R48 R49 R49 R50 R51 R49 R49 R49 R50 ─ ─
10 R52 R53 R53 R54 R55 R53 R53 R53 R54 ─ ─
12 R56 R57 R57 R58 R60 R57 R57 R57 ─ R57 R57
14 R59 R61 R62 R63 ─ ─ ─ ─ R63 R61 R62
16 R64 R65 R66 R67 ─ R65 R65 R66 ─ R65 R66
18 R68 R69 R70 R71 ─ ─ R69 R70 ─ R69 R70
20 R72 R73 R74 R75 ─ R73 R73 R74 ─ R73 R74
22 ─ ─ ─ ─ ─ ─ ─ ─ ─ R81 ─
24 R76 R77 R78 R79 ─ ─ ─ ─ ─ R77 R78
26 ─ R93 R100 ─ ─ ─ ─ ─ ─ R93 R100
28 ─ R94 R101 ─ ─ ─ ─ ─ ─ R94 R101
30 ─ R95 R102 ─ ─ ─ ─ ─ ─ R95 R102
32 ─ R96 R103 ─ ─ ─ ─ ─ ─ R96 R103
34 ─ R97 R104 ─ ─ ─ ─ ─ ─ R97 R104
36 ─ R98 R105 ─ ─ ─ ─ ─ ─ R98 R105
Notes: (1) R30 is only applicable for lapped joint flange.
(2) If the groove (same R number) is the same, both oval and octagonal can be used.
TOMBO No.1850-CTOMBO No.1850-V
Octagonal type
Oval type
R31
Standard
Dim
ension Charts
83
For ASME B16.5 FlangesFor ASME B16.47 Series B Flanges NAFLONTM PTFE Cushion Gasket (TOMBO� No.9010-NA-A/B)
Nominal
Pipe SizeD1 D2
Class 75 Class 150 Class 300
D3 D4 D3 D4 D3 D4T Type
Dimension Chart 15 Unit : A
1/2 17 24 ─ ─ 36 47 36 53
3/4 22 29 ─ ─ 44 56 44 66
1 28 35 ─ ─ 52 66 52 72
11/4 36 43 ─ ─ 65 75 65 82
11/2 42 49 ─ ─ 74 85 74 94
2 53 60 ─ ─ 92 104 92 110
21/2 66 73 ─ ─ 105 123 105 129
3 90 97 ─ ─ 127 135 127 148
31/2 103 110 ─ ─ 140 161 140 164
4 116 123 ─ ─ 157 173 157 180
5 143 150 ─ ─ 186 196 186 215
6 169 176 ─ ─ 216 221 216 250
8 220 227 ─ ─ 270 277 270 306
10 275 282 ─ ─ 324 338 324 360
12 326 333 ─ ─ 381 408 381 420
14 358 365 ─ ─ 413 449 413 484
16 408 415 ─ ─ 470 512 470 538
18 459 466 ─ ─ 533 547 533 595
20 510 517 ─ ─ 584 604 584 651
24 612 619 ─ ─ 692 715 692 772
26 673 677 705 705 711 722 737 769
28 724 728 756 756 762 773 787 822
30 775 779 806 807 813 824 845 833
32 826 830 857 857 864 878 902 937
34 876 880 908 908 921 932 952 991
36 927 931 965 970 972 984 1,010 1,045
38 978 982 1,016 1,021 1,022 1,042 1,060 1,096
40 1,029 1,033 1,067 1,072 1,080 1,092 1,118 1,146
42 1,080 1,084 1,118 1,123 1,130 1,143 1,168 1,197
44 1,130 1,134 1,168 1,178 1,187 1,194 1,219 1,248
46 1,181 1,185 1,226 1,229 1,238 1,253 1,276 1,315
48 1,232 1,236 1,276 1,280 1,289 1,304 1,327 1,365
54 1,384 1,388 1,429 1,435 1,441 1,461 1,480 1,527
60 1,537 1,541 1,588 1,594 1,600 1,625 1,651 1,702
Notes: (1) Dimensions for class 150 up to 24” are same as JPI-7S-15-1999.
Other dimensions are designed by NICHIAS Corporation tofit to the applicable flanges.
(2) Applicable flanges are ASME B16.5, ASME B16.47 Series B,API 605, JPI-7S-15 and JPI-7S-43.
(3) Dimensions in brackets are for TOMBO No.9010-NA-A-5/-NA-A-7 andTOMBO No.9010-NA-B-5/-NA-B-7.
(4) For slip-on flanges, gaskets for 1/2” to 2-1/2” cannot be used sincethe gasket I.D. (D1) is smaller than the flange I.D.
A-6 Type, A-8 Type B-6 Type, B-8 Type
3.2
(2.8)
3.2
(3.8)
5.0
(3.8)
B Type
A Type
Sta
ndar
dD
imen
sion
Cha
rts
84
For ASME B16.47 Series A FlangesFor MSS SP-44 Flanges NAFLONTM PTFE Cushion Gasket (TOMBO� No.9010-NA-B)
Nominal Pipe Size
A BD1 D2
Class 150 Class 300
D3 D4 D3 D4T Type
Dimension Chart 16 Unit : A
650 26 673 677 749 775 749 835
700 28 724 728 800 832 800 899
750 30 775 779 857 883 857 952
800 32 826 830 914 940 914 1,006
850 34 876 880 965 991 965 1,057
900 36 927 931 1,022 1,048 1,022 1,118
950 38 978 982 1,073 1,111 1,029 1,054
1,000 40 1,029 1,033 1,124 1,162 1,086 1,114
1,050 42 1,080 1,084 1,194 1,219 1,137 1,165
1,100 44 1,130 1,134 1,245 1,276 1,194 1,219
1,150 46 1,181 1,185 1,295 1,327 1,245 1,273
1,200 48 1,232 1,236 1,359 1,384 1,302 1,324
1,250 50 1,283 1,287 1,410 1,435 1,359 1,378
1,300 52 1,334 1,338 1,460 1,492 1,410 1,429
1,350 54 1,384 1,388 1,511 1,549 1,467 1,492
1,400 56 1,435 1,439 1,575 1,607 1,518 1,543
1,450 58 1,486 1,490 1,626 1,664 1,575 1,594
1,500 60 1,537 1,541 1,676 1,714 1,626 1,645
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to the applicable flanges.
(2) Applicable flanges are ASME B16.47 Series A and MSS SP-44 flanges.
(3) Dimensions in brackets are for TOMBO No.9010-NA-B-5/-NA-B-7.
B-6 Type, B-8 Type
5.0
(3.8)
3.2
(3.8)
B Type
Standard
Dim
ension Charts
85
For ASME B16.1 Flanges For Taylor Forge Flanges NAFLONTM PTFE Cushion Gasket (TOMBO� No.9010-NA-B)
Nominal Pipe Size
A BD1 D2
Class 125 Class 250
D3 D4 D3 D4T Type
Dimension Chart 17 Unit : A
650 26☆ 673 677 767 775 824 832
700 28☆ 724 728 824 832 887 895
750 30 775 779 875 883 945 952
800 32☆ 826 830 932 940 1,002 1,010
850 34☆ 876 880 983 991 1,053 1,060
900 36 927 931 1,040 1,048 11,10 1,118
950 38 978 982 1,103 1,111 1,160 1,168
1,000 40☆ 1,029 1,033 1,154 1,162 1,218 1,226
1,050 42 1,080 1,084 1,211 1,219 1,281 1,289
1,100 44☆ 1,130 1,134 1,268 1,276 1,338 1,346
1,150 46☆ 1,181 1,185 1,319 1,327 1,396 1,403
1,200 48 1,232 1,236 1,376 1,384 1,484 1,492
1,250 50☆ 1,283 1,287 1,427 1,435 ─ ─
1,300 52☆ 1,334 1,338 1,484 1,492 ─ ─
1,350 54 1,384 1,388 1,541 1,549 ─ ─
1,500 60 1,537 1,541 1,707 1,714 ─ ─
1,650 66☆ 1,689 1,693 1,878 1,886 ─ ─
1,800 72 1,842 1,846 2,043 2,051 ─ ─
2,100 84 2,146 2,150 2,367 2,375 ─ ─
2,400 96 2,451 2,455 2,691 2,699 ─ ─
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to the applicable flanges.
(2) Applicable flanges are ASME B 16.1-1998 and Taylor Forge Flanges.☆marked sizes are for Taylor Forge flanges
(3) Dimensions in brackets are for TOMBO No.9010-NA-B-5/-NA-B-7.
B-6 Type, B-8 Type
5.0
(3.8)
3.2
(3.8)
B Type
Sta
ndar
dD
imen
sion
Cha
rts
86
For ASME B16.5 Flanges NAFLONTM PTFE Cushion Gasket (TOMBO� No.9010-NA-AS)
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to the applicable flanges.
(2) Applicable flanges are ASME B 16.5 and JPI-7S-15.
(3) Dimensions in brackets are for TOMBO No.9010-NA-AS-5/-NA-AS-7.
Nominal Pipe Size
A BD1 D2
Class 150 Class 300
D3 TD4 D3 D4 TType
Dimension Chart 18 Unit : A
15 1/2 21 24 47 47
20 3/4 26 29 56 56
25 1 32 35 66 66
32 11/4 40 43 75 75
40 11/2 46 49 85 85
50 2 57 60 92 104
65 21/2 70 73 105 123
80 3 94 97 127 135
90 31/2 107 110 140 161
100 4 120 123 157 173
125 5 147 150 186 196
150 6 173 176 216 221
200 8 224 227 270 277
250 10 279 282 324 338
300 12 330 333 381 408
350 14 362 365 413 449
400 16 412 415 470 512
450 18 463 466 533 547
500 20 514 517 584 604
600 24 616 619 692 715
36 53
44 66
52 72
65 82
74 94
92 110
105 129
127 148
140 164
157 180
186 215
216 250
270 306
324 360
381 420
413 484
470 538
533 595
584 651
692 772
AS-6 Type, AS-8 Type
3.4
(3.0)
2.5
(2.5)
3.4
(3.0)
2.5
(2.8)
AS Type
Standard
Dim
ension Charts
87
For ASME B16.5 Flanges NAFLONTM PTFE Cushion Gasket (High temperature applications) (TOMBO� No.9010-NA-A-9)
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to the applicable flanges.
(2) Applicable flanges are ASME B 16.5 and JPI-7S-15
(3) For slip-on flanges, gaskets for 1/2” to 2-1/2” cannot be used since the gasket I.D. (D1) issmaller than the flange I.D.
Nominal Pipe Size
A BD1 D2
Class 150 Class 300
D3I.D O.D
D4Wire mesh
D3I.D O.D
D4Wire mesh t T Type
Dimension Chart 19 Unit : A
15 1/2 17 25 47 47 26 36 47 53 26 36
20 3/4 22 30 56 56 31 42 56 66 31 42
25 1 28 36 66 66 38 50 66 72 38 50
32 11/4 36 44 75 75 49 63 75 82 49 63
40 11/2 42 50 85 85 55 72 85 94 55 72
50 2 53 61 92 104 70 90 92 110 70 90
65 21/2 66 74 105 123 83 103 105 129 83 103
80 3 90 98 127 135 105 125 127 148 105 125
90 31/2 103 111 140 161 118 138 140 164 118 138
100 4 116 124 157 173 136 155 157 180 136 155
125 5 143 151 186 196 164 184 186 215 164 184
150 6 169 177 216 221 194 214 216 250 194 214
200 8 220 228 270 277 242 268 270 306 242 268
250 10 275 283 324 338 290 322 324 360 290 322
300 12 326 334 381 408 347 379 381 420 347 379
350 14 358 365 413 449 377 411 413 484 377 411
400 16 408 416 470 512 432 468 470 538 432 468
450 18 459 467 533 547 487 531 533 595 487 531
500 20 510 518 584 604 537 582 584 651 537 582
600 24 612 620 692 715 637 690 692 772 637 690
O.D
T t
I.D
D1
D2D3
D4
A Type
3.92.0 A Type
Sta
ndar
dD
imen
sion
Cha
rts
88
For NAFLONTM Lined Piping NAFLONTM PTFE Cushion Gasket (TOMBO� No.9010-NA-FG-7)
Notes: (1) TOMBO No.9010-NA-FG-7 is a PTFE jacket type gasket used for anti-corrosion NAFLONlined piping.
If a solid type product is required, please use the TOMBO No.9007 NAFLON PTFE cutgasket or TOMBO No.9007-LC NAFLON Low creap gasket.
For D1, D4 and t, follow same dimensions as above chart.
(2) Applicable flanges are flanges for fluoro-piping, 1/2” to 12” Class 150
Nominal Pipe Size
A B
For ANSI (JPI) Class 150
D1 tD4 TType
Dimension Chart 20 Unit : A
15 1/2 16 47
20 3/4 22 56
25 1 28 66
40 11/4 45 85
50 2 58 104
65 21/2 71 123
80 3 85 135
100 4 110 173
125 5 128 196
150 6 160 221
200 8 214 277
250 10 266 338
300 12 328 408
56
1 28
66
40
116 160
221
AS-7 Type
NAFLON PTFE Cut Gasket(TOMBO No.9007)
NAFLON Low Creap Gasket(TOMBO No.9007-LC)
A-7 Type
2.31.5
AS-7 Type
A-7 Type
Standard
Dim
ension Charts
89
For ASME B16.5 Flanges For JPI Flanges EbilonTM Gasket
Dimension Chart 21 Unit : A
Nominal Pipe Size Gaskets Seal section diameter Bolts
OuterdiameterA
InnerdiameterB
Width ofRingB
Thickness
T
Width ofRingA
Width ofRingC
Width ofRingD
Width ofRingPCD
Width ofRingn-φk
Reference
E
15 1/2 86 18 5 30 ─ 60 4-16 42
20 3/4 96 22 5 30 42 70 4-16 52
25 1 105 29 5 37 50 79 4-16 60
(32) (11/4) 115 38 5 46 59 89 4-16 70
40 11/2 125 43 5 53 68 98 4-16 79
50 2 150 54 5 64 83 121 4-19 99
65 21/2 175 69 5 81 101 140 4-19 118
80 3 188 80 5 92 112 152 4-19 130
(90) (31/2) 213 90 5 110 134 178 8-19 154
100 4 226 103 5 124 148 190 8-19 168
(125) (5) 252 129 5 150 174 216 8-22 190
150 6 277 153 5 172 196 241 8-22 212
200 8 340 200 5 222 246 298 8-22 270
250 10 404 254 6 276 300 362 12-25 330
300 12 480 305 6 335 365 432 12-25 400
350 14 530 337 6 365 395 476 12-29 440
400 16 594 387 6 425 455 540 16-29 500
450 18 632 438 6 475 505 578 16-32 538
500 20 696 489 6 525 555 635 20-32 595
600 24 810 591 6 625 665 749 20-35 706
Notes: (1) Applicable gaskets are Ebilon Gaskets TOMBO No.9013, 9013-D, 9013-EP and 9013-DEP.
(2) These gasket dimensions are designed by NICHIAS Corporation to fit to weld-neck flanges of JPI-7S-15-85.
(3) Applicable flanges are weld-neck flanges and socket-welded flanges of JPI-7S-15-85. It is also used for ASME B 16.5 flanges.
FOR ASME / JPI Class 150 Flanges Electrical Insulation Bolt Kit (TOMBO� No.9910/9910H, TOMBO� No.9011-NA-E5)
90
Sta
ndar
dD
imen
sion
Cha
rts
Dimension Chart 22 Unit : A
d1
rs
L
t
H
d1D2d2
t2
Metal
D2d2
t1
Insulationt3
d3D5
d3D5
t3t3
Insulation bolt Hexagonal nut Insulating washerMetal washer
Insulating gasket
Nominal pipe size Insulation bolt Hexagonal
nutInsulating washerMetal washer Insulating gasket Number
of bolts
Width ofRingB
Width ofRingd1
Width ofRingL
Width ofRingRs
t
TOMBO No.9910
TOMBO No.9910-H
Width ofRingH
Width ofRingd2
Width ofRingD2
Width ofRingt1
Width ofRingt2
Width ofRingd3
Width ofRingD5
Width ofRingt3
Width ofRingN
1/2
3/4
1
1 1/4
1 1/2
2
2 1/2
3
3 1/2
4
5
6
8
10
12
14
16
18
20
24
1/2-UNC
1/2-UNC
1/2-UNC
1/2-UNC
1/2-UNC
5/8-UNC
5/8-UNC
5/8-UNC
5/8-UNC
5/8-UNC
3/4-UNC
3/4-UNC
3/4-UNC
7/8-UNC
7/8-UNC
1-UNC
1-UNC
1 1/8-8UN
1 1/8-8UN
1 1/4-8UN
82
82
86
92
92
103
109
113
113
113
121
121
130
148
148
165
165
183
191
207
36
36
40
46
46
51
57
61
61
61
63
63
72
78
78
87
87
95
103
113
0.7 1.0
12.7
12.7
12.7
12.7
12.7
15.9
15.9
15.9
15.9
15.9
19.1
19.1
19.1
22.2
22.2
25.4
25.4
28.6
28.6
31.8
13.5
13.5
13.5
13.5
13.5
17.0
17.0
17.0
17.0
17.0
21.0
21.0
21.0
23.5
23.5
27.0
27.0
30.0
30.0
33.5
26
26
26
26
26
32
32
32
32
32
40
40
40
44
44
52
52
58
58
62
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
2.3
2.3
2.3
2.3
2.3
2.6
2.6
2.6
2.6
2.6
3.2
3.2
3.2
3.2
3.2
4.0
4.0
4.5
4.5
4.5
16
21
27
36
41
53
62
74
86
98
123
147
196
245
295
336
387
437
485
587
47
57
66
76
85
103
122
135
161
173
196
221
277
338
408
449
512
547
604
715
2.5
2.5
2.5
2.5
2.5
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
4
4
4
4
4
4
4
4
8
8
8
8
8
12
12
12
16
16
20
20
*Applicable flange: ASME B 16.5 (Class 150 and 300), JPI-75-15-81(Class 150 and 300).
*The inner diameter of gasket is the same as that of STPG sch40 steel pipe for up to nominal size of 12B, the same as or 4mm smaller than that of STPG sch20 steelpipe.
*The size of TOMBO No.9910 is the same as that of TOMBO No.9910-H except for "t" that stands for the thickness of insulating sleeve.
*If service temperature is over 150℃, TOMBO No.9910-H/9007-LC should be used. Please consult with us about the size of the TOMBO No.9007-LC.
FOR ASME / JPI Class 300 Flanges Electrical Insulation Bolt Kit (TOMBO� No.9910/9910H, TOMBO� No.9011-NA-ES)
91
Standard
Dim
ension Charts
Dimension Chart 23 Unit : A
Nominal pipe size Insulation bolt Hexagonal
nutInsulating washerMetal washer Insulating gasket Number
of bolts
Width ofRingB
Width ofRingd1
Width ofRingL
Width ofRingRs
t
TOMBO No.9910
TOMBO No.9910-H
Width ofRingH
Width ofRingd2
Width ofRingD2
Width ofRingt1
Width ofRingt2
Width ofRingd3
Width ofRingD5
Width ofRingt3
Width ofRingN
1/2
3/4
1
1 1/4
1 1/2
2
2 1/2
3
3 1/2
4
5
6
8
10
12
14
16
18
20
24
1/2-UNC
5/8-UNC
5/8-UNC
5/8-UNC
3/4-UNC
5/8-UNC
3/4-UNC
3/4-UNC
3/4-UNC
3/4-UNC
3/4-UNC
3/4-UNC
7/8-UNC
1-UNC
1 1/8-8UN
1 1/8-8UN
1 1/4-8UN
1 1/8-8UN
1 1/4-8UN
1 1/2-8UN
86
98
98
103
115
109
121
130
136
136
145
145
168
190
204
212
224
230
238
268
40
46
46
51
55
57
63
72
76
76
85
85
98
110
116
124
130
136
144
158
0.7 1.0
12.7
15.9
15.9
15.9
19.1
15.9
19.1
19.1
19.1
19.1
19.1
19.1
22.2
25.4
28.6
28.6
31.8
31.8
31.8
38.1
13.5
17.0
17.0
17.0
21.0
17.0
21.0
21.0
21.0
21.0
21.0
21.0
23.5
27.0
30.0
30.0
33.5
33.5
33.5
40.0
26
32
32
32
40
32
40
40
40
40
40
40
44
52
58
58
62
62
62
72
4
4
4
4
4
4
4
4
4
4
4
4
6
6
6
6
6
6
6
6
2.3
2.6
2.6
2.6
3.2
2.6
3.2
3.2
3.2
3.2
3.2
3.2
3.2
4.0
4.5
4.5
4.5
4.5
4.5
5.0
16
21
27
36
41
53
62
74
86
98
123
147
196
245
295
336
387
437
485
587
53
66
72
82
95
110
129
148
164
180
215
250
306
360
420
484
538
595
651
772
2.5
2.5
2.5
2.5
2.5
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
4
4
4
4
4
8
8
8
8
8
8
12
12
16
16
20
20
24
24
24
*The inner diameter of gasket is the same as that of STPG sch40 steel pipe for up to nominal size of 12B, the same as or 4mm smaller than that of STPG sch20 steelpipe.
*Please let us know if whitworth screw thread is used.
*The size of TOMBO No.9910 is the same as that of TOMBO No.9910-H except for "t" that stands for the thickness of insulating sleeve.
*If service temperature is over 150℃, TOMBO No.9910-H/9007-LC should be used. Please consult with us about the size of the TOMBO No.9007-LC.
d1
rs
L
t
H
d1D2d2
t2
Metal
D2d2
t1
Insulationt3
d3D5
d3D5
t3t3
Insulation bolt Hexagonal nut Insulating washerMetal washer
Insulating gasket
Standard
Dim
ension Charts
93
For JIS Flanges Soft Gasket, Flat Ring Gasket
Dimension Chart 24 Unit : A
Nominal
Pipe Size
Gasket
inner
diameter
D1
For full face/ large raised face/small raised
Gasket outer diameter D2
Nominalpressure2K
Nominalpressure5K
Nominalpressure10K
Thin flangenominal pressure10K
Nominalpressure16K
Nominalpressure20K
Nominalpressure30K
Nominalpressure40K
Nominalpressure63K
10A 18 ─ 45 53 55 53 53 59 59 6415 22 ─ 50 58 60 58 58 64 64 6920 28 ─ 55 63 65 63 63 69 69 7525 35 ─ 65 74 78 74 74 79 79 8032 43 ─ 78 84 88 84 84 89 89 9040 49 ─ 83 89 93 89 89 100 100 10850 61 ─ 93 104 108 104 104 114 114 12565 ─ 118 124 128 124 124 140 140 15380 90 ─ 129 134 138 140 140 150 150 16390 102 ─ 139 144 148 150 150 163 163 181100 115 ─ 149 159 163 165 165 173 183 196125 141 ─ 184 190 194 203 203 208 226 235150 167 ─ 214 220 224 238 238 251 265 275175 192 ─ 240 245 249 ─ ─ ─ ─ ─200 218 ─ 260 270 274 283 283 296 315 330225 244 ─ 285 290 294 ─ ─ ─ ─ ─250 270 ─ 325 333 335 356 356 360 380 394300 321 ─ 370 378 380 406 406 420 434 449350 359 ─ 413 423 425 450 450 465 479 488400 410 ─ 473 486 488 510 510 524 534 548450 460 535 533 541 ─ 575 575 ─ ─ ─500 513 585 583 596 ─ 630 630 ─ ─ ─550 564 643 641 650 ─ 684 684 ─ ─ ─600 615 693 691 700 ─ 734 734 ─ ─ ─650 667 748 746 750 ─ 784 805 ─ ─ ─700 718 798 796 810 ─ 836 855 ─ ─ ─750 770 856 850 870 ─ 896 918 ─ ─ ─800 820 906 900 920 ─ 945 978 ─ ─ ─850 872 956 950 970 ─ 995 1,038 ─ ─ ─900 923 1,006 1,000 1,020 ─ 1,045 1,088 ─ ─ ─1,000 1,025 1,106 1,100 1,124 ─ 1,158 ─ ─ ─ ─1,100 1,130 1,216 1,210 1,234 ─ 1,258 ─ ─ ─ ─1,200 1,230 1,326 1,320 1,344 ─ 1,368 ─ ─ ─ ─1,300 1,335 ─ ─ ─ ─ 1,474 ─ ─ ─ ─1,350 1,385 1,481 1,475 1,498 ─ 1,534 ─ ─ ─ ─1,400 1,435 ─ ─ ─ ─ 1,584 ─ ─ ─ ─1,500 1,540 1,636 1,630 1,658 ─ 1,694 ─ ─ ─ ─
84〔77〕
For full face flanges For large raised face flanges
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets, clothreinforced rubber cut gaskets, Graseal gaskets and PTFE cutgaskets.
(2) This dimension chart is the same as the dimensions shown below.
JIS B2404-2666 “Dimensions of gaskets for use with pipe flange“reference, table 4.
But, dimensions below〔 〕and one for 2K,40K and 63K which are
Not specified by the above standard are as per JIS B2404-1999
“Dimensions of gaskets for use with pipe flange“ reference, table 7.
(3) Applicable flanges are those specified in the following standards.JIS B2220-2004 “Steel welding pipe flanges“JIS B2239-2004 “Cast iron pipe flanges“JIS B2240-2006 “General rulus for copper alloy pipe flanges“JIS B2241-2006 “Basic dimensions of aluminum alloy pipe flanges“JIS B2240-1996 “General rules for copper alloy pipe flanges“JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
(4) Joint sheets, Graseal gaskets and PTFE cut gaskets are not recommendedfor nominal pressures of 2K and 5K.
(5) For nominal pressure of 30K and above, soft gaskets are not recommended.
Sta
ndar
dD
imen
sion
Cha
rts
94
For JIS Flanges Soft Gasket/Full Face Gasket (F.F.)
Dimension Chart 25 Unit : A
Nominal
Pipe Size
Gasketinnerdiameter
D1
Nominal pressure 2K 5K 10K 16K
Gasketouterdiameter
D2
Bolt circlediameter
C
n × h
Gasketouterdiameter
D2
Bolt circlediameter
C
n × h
Gasketouterdiameter
D2
Bolt circlediameter
C
n × h
Gasketouterdiameter
D2
Bolt circlediameter
C
n × h
10A 18 ─ ─ ─ 75 55 4×12 90 65 4×15 90 65 4×1515 22 ─ ─ ─ 80 60 4×12 95 70 4×15 95 70 4×1520 28 ─ ─ ─ 85 65 4×12 100 75 4×15 100 75 4×1525 35 ─ ─ ─ 95 75 4×12 125 90 4×19 125 90 4×1932 43 ─ ─ ─ 115 90 4×15 135 100 4×19 135 100 4×1940 49 ─ ─ ─ 120 95 4×15 140 105 4×19 140 105 4×1950 61 ─ ─ ─ 130 105 4×15 155 120 4×19 155 120 8×1965 ─ ─ ─ 155 130 4×15 175 140 4×19 175 140 8×1980 90 ─ ─ ─ 180 145 4×19 185 150 8×19 200 160 8×2390 102 ─ ─ ─ 190 155 4×19 195 160 8×19 210 170 8×23100 115 ─ ─ ─ 200 165 8×19 210 175 8×19 225 185 8×23125 141 ─ ─ ─ 235 200 8×19 250 210 8×23 270 225 8×25150 167 ─ ─ ─ 265 230 8×19 280 240 8×23 305 260 12×25175 192 ─ ─ ─ 300 260 8×23 305 265 12×23 ─ ─ ─200 218 ─ ─ ─ 320 280 8×23 330 290 12×23 350 305 12×25225 244 ─ ─ ─ 345 305 12×23 350 310 12×23 ─ ─ ─250 270 ─ ─ ─ 385 345 12×23 400 355 12×25 430 380 12×27300 321 ─ ─ ─ 430 390 12×23 445 400 16×25 480 430 16×27350 359 ─ ─ ─ 480 435 12×25 490 445 16×25 540 480 16×33400 410 ─ ─ ─ 540 495 16×25 560 510 16×27 605 540 16×33450 460 605 555 16×23 605 555 16×25 620 565 20×27 675 605 20×33500 513 655 605 20×23 655 605 20×25 675 620 20×27 730 660 20×33550 564 720 655 20×25 720 665 20×27 745 680 20×33 795 720 20×39600 615 770 715 20×25 770 715 20×27 795 730 24×33 845 770 24×39650 667 825 770 24×25 825 770 24×27 845 780 24×33 ─ ─ ─700 718 875 820 24×25 875 820 24×27 905 840 24×33 ─ ─ ─750 770 945 880 24×27 945 880 24×33 970 900 24×33 ─ ─ ─800 820 995 930 24×27 995 930 24×33 1,020 950 28×33 ─ ─ ─850 872 1,045 980 24×27 1,045 980 24×33 1,070 1,000 28×33 ─ ─ ─900 923 1,095 1,030 24×27 1,095 1,030 24×33 1,120 1,050 28×33 ─ ─ ─1,000 1,025 1,195 1,130 28×27 1,195 1,130 28×33 1,235 1,160 28×39 ─ ─ ─1,100 1,130 1,305 1,240 28×27 1,305 1,240 28×33 1,345 1,270 28×39 ─ ─ ─1,200 1,230 1,420 1,350 32×27 1,420 1,350 32×33 1,465 1,380 32×39 ─ ─ ─1,350 1,385 1,575 1,505 32×27 1,575 1,505 32×33 1,630 1,540 36×45 ─ ─ ─1,500 1,540 1,730 1,660 36×27 1,730 1,660 36×33 1,795 1,700 40×45 ─ ─ ─
84〔77〕
Notes: (1) Soft gaskets include joint sheet gaskets, rubber cut gaskets, clothreinforced rubber cut gaskets, Graseal gaskets and PTFE cutgaskets.
(2) This dimension chart is the same as the dimensions shown below.
JIS B2404-2006 “Dimensions of gaskets for use with pipe flange“
reference, table 2 and 3.
But, dimensions below〔 〕and one for 2K which is not specified
By the above standard are as per JIS B2404-1999 “Dimensions ofGaskets for use with pipe flange“ reference, table 6.
(3) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2239-2004 “Cast iron pipe flanges“
JIS B2240-2006 “General rulus for copper alloy pipe flanges“
JIS B2241-2006 “Basic dimensions of aluminum alloy pipe flanges“
JIS B2240-1996 “General rules for copper alloy pipe flanges“
JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
(4) Joint sheets, Graseal gaskets and PTFE cut gaskets are not recommended fornominal pressures of 2K and 5K.
Even 10K and 16K full face gaskets are not suitable for gas sealing due toinsufficient seating stress.
Standard
Dim
ension Charts
95
For JIS, M&F, T&G Flanges Soft Gasket
Nominal Pipe Size
Tongue & GrooveMale & Female
Gasket inner
diameter
D1
Gasket outer
diameter
D2
Gasket inner
diameter
D1
Gasket outer
diameter
D2
Dimension Chart 26 Unit : A
10A 18 38 28 3815 22 42 32 4220 28 50 38 5025 35 60 45 6032 43 70 55 7040 49 75 60 7550 61 90 70 9065 77 110 90 11080 90 120 100 12090 102 130 110 130100 115 145 125 145125 141 175 150 175150 167 215 190 215200 218 260 230 260250 270 325 295 325300 321 375 340 375350 359 415 380 415400 410 475 440 475450 460 523 483 523500 513 575 535 575550 564 625 585 625600 615 675 635 675650 667 727 682 727700 718 777 732 777750 770 832 787 832800 820 882 837 882850 872 934 889 934900 923 987 937 9871,000 1,025 1,092 1,042 1,0921,100 1,130 1,192 1,142 1,1921,200 1,230 1,292 1,237 1,2921,300 1,335 1,392 1,337 1,3921,350 1,385 1,442 1,387 1,4421,400 1,435 1,492 1,437 1,4921,500 1,540 1,592 1,537 1,592
Notes: (1) The materials used are mainly joint sheet, Graseal, and PTFE cut gaskets.
(2) This dimension chart is the same as the dimensions shown below.
JIS B 2404-2006 “Dimensions of gaskets for pipe flanges” Chart-5
(3) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
JIS B2239-1996 “General rules for cast iron pipe flanges“ (Discontinued)
Male & Female Tongue & Groove
Sta
ndar
dD
imen
sion
Cha
rts
96
For JIS Flanges VortexTM Gasket with Outer Ring
Nominal
Pipe
Size
Thickness
T
4.5
Nominal pressure 10K
Innerdiameter
D2
Outerdiameter
D3
Outer ringouterdiameter D4
16, 20K
Innerdiameter
D2
Outerdiameter
D3
Outer ringouterdiameter D4
30K
Innerdiameter
D2
Outerdiameter
D3
Outer ringouterdiameter D4
40K
Innerdiameter
D2
Outerdiameter
D3
Outer ringouterdiameter D4
63K
Innerdiameter
D2
Outerdiameter
D3
Outer ringouterdiameter D4
Dimension Chart 27 Unit : A
10A 24 37 52 24 37 52 24 37 59 21 34 59 21 34 64
15 28 41 57 28 41 57 28 41 64 24 37 64 24 37 69
20 34 47 62 34 47 62 34 47 69 29 42 69 29 42 75
25 40 53 74 40 53 74 40 53 79 35 48 79 35 48 80
32 51 67 84 51 67 84 51 67 89 44 60 89 44 60 90
40 57 73 89 57 73 89 57 73 100 51 67 100 51 67 107
50 69 89 104 69 89 104 69 89 114 63 79 114 63 79 125
65 87 107 124 87 107 124 78 98 140 78 98 140 78 98 152
80 98 118 134 99 119 140 90 110 150 90 110 150 90 110 162
90 110 130 144 114 139 150 102 127 162 102 127 162 102 127 179
100 123 143 159 127 152 165 116 141 172 116 141 182 116 141 194
125 148 173 190 152 177 202 140 165 207 140 165 224 140 165 235
150 174 199 220 182 214 237 165 197 249 165 197 265 165 197 275
175 201 226 245 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─
200 227 252 270 233 265 282 218 250 294 218 250 315 218 250 328
225 252 277 290 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─
250 278 310 332 288 328 354 271 311 360 271 311 378 271 311 394
300 329 361 377 339 379 404 320 360 418 320 360 434 320 360 446
350 366 406 422 376 416 450 356 396 463 356 396 479 356 396 488
400 417 457 484 432 482 508 403 453 524 403 453 531 403 453 545
450 468 518 539 483 533 573 ─ ─ ─ ─ ─ ─ ─ ─ ─
500 518 568 594 533 583 628 ─ ─ ─ ─ ─ ─ ─ ─ ─
550 569 619 650 584 634 684 ─ ─ ─ ─ ─ ─ ─ ─ ─
600 620 670 700 635 685 734 ─ ─ ─ ─ ─ ─ ─ ─ ─
Notes: (1) This dimension chart is the same as the dimensions shown below.
JIS B 2404-1999 “Dimension of gaskets for pipe flanges” Chart 12 ~ 16
(2) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
JIS B2239-1996 “General rules for cast iron pipe flanges“ (Discontinued)
However, the dimensions of 10K, 16K and 20K cannot be used forsmall raised face gaskets.
In the case of the dimensions of 30K, a nominal size of 50A and undercan only be used for large raised face gaskets. 65A and over can beused for both large and small raised face gaskets, but these are onlyapplicable for weld-neck (butt-welded) flanges and C type slip-onwelded flanges as specified in JIS B 2220. The dimensions of 40K and63K are suitable for large and small raised face gaskets, but these areonly applicable for weld-neck flanges and C type slip-on welded flangesas specified in JIS B 2220.
(3) For the 30K A and B type slip-on welded flanges, please use the dimensionsshown on Page 96. Dimension Charts 28 & 29
(4) For flanges with a nominal pressure of 63K, Vortex gaskets with inner and outerrings are recommended.
(5) For Graseal and Naflon Vortex gaskets, those with inner and outer ring type arerecommended.
(6) For 2K and 5K flanges, Vortex gaskets are not recommended.
(7) For bolting material, high-tension bolts such as B7 (SNB7) and above are required.
(8) The gasket outer diameter for the types with outer ring indicates the shoulderdimensions of the gasket excluding spring layers.
Standard
Dim
ension Charts
97
For JIS Flanges VortexTM Gasket with Outer and Inner Ring
Nominal
Pipe
Size
Thickness
T
4.5
Nominal pressure 16, 20K
Innerdiameter
D2
Inner ring inner diameter D1
Outerdiameter
D3
Outer ringouterdiameter D4
Innerdiameter
D2
Inner ring inner diameter D1
Outerdiameter
D3
Outer ringouterdiameter D4
Innerdiameter
D2
Inner ring inner diameter D1
Outerdiameter
D3
Outer ringouterdiameter D4
Innerdiameter
D2
Inner ring inner diameter D1
Outerdiameter
D3
Outer ringouterdiameter D4
30K 40K 63K
Dimension Chart 28 Unit : A
10A 18 24 37 52 18 24 34 59 15 21 34 59 15 21 34 64
15 22 28 41 57 22 28 41 64 18 24 37 64 18 24 37 69
20 28 34 47 62 28 34 47 69 23 29 42 69 23 29 42 75
25 34 40 53 74 34 40 53 79 29 35 48 79 29 35 48 80
32 43 51 67 84 43 51 67 89 38 44 60 89 38 44 60 90
40 49 57 73 89 49 57 73 100 43 51 67 100 43 51 67 107
50 61 69 89 104 61 69 89 114 55 63 79 114 55 63 79 125
65 77 87 107 124 68 78 98 140 68 78 98 140 68 78 98 152
80 89 99 119 140 80 90 110 150 80 90 110 150 80 90 110 162
90 102 114 139 150 92 102 127 162 92 102 127 162 92 102 127 179
100 115 127 152 165 104 116 141 172 104 116 141 182 104 116 141 194
125 140 152 177 202 128 140 165 207 128 140 165 224 128 140 165 235
150 166 182 214 237 153 165 197 249 153 165 197 265 153 165 197 275
200 217 233 265 282 202 218 250 294 202 218 250 315 202 218 250 328
250 268 288 328 354 251 271 311 360 251 271 311 378 251 271 311 394
300 319 339 379 404 300 320 360 418 300 320 360 434 300 320 360 446
350 356 376 416 450 336 356 396 463 336 356 396 479 336 356 396 488
400 407 432 482 508 383 403 453 524 383 403 453 531 383 403 453 545
450 458 483 533 573 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─
500 508 533 583 628 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─
550 559 584 634 684 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─
600 610 635 685 734 ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─
Notes: (1) This dimension chart is the same as the dimensions shownbelow.
JIS B 2404-1999 “Dimensions of gaskets for pipe flanges”Chart 17 ~ 20
(2) Applicable flanges are those specified in the followingstandards.
Applicable flanges:
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
JIS B2239-1996 “General rules for cast iron pipe flanges“ (Discontinued)
For 16K and 20K, these dimensions cannot be used for smallraised face flanges.
For 30K, 10A-50A are only applicable for large raised face.
65A and above are applicable for large and small raised face,but limited to only for weld-neck flanges and C type slip-onflanges as per JIS B 2220.
For 40K and 63K, applicable for large and small raised face, butlimited to only weld-neck flanges and C type slip-on flanges as perJIS B 2220.
(3) For 30K A and B type slip-on flanges, use the dimensions shown onPage 35. Dimension Charts 28 & 29
(4) For bolting material, high-tension bolts such as B7 (SNB7) and aboveare required.
(5) The gasket outer diameter for the types with outer ring indicates theshoulder dimensions of the gasket excluding spring layers.
Sta
ndar
dD
imen
sion
Cha
rts
98
For JIS Large Flanges VortexTM Gasket with Outer and Inner Ring
Notes: (1) These dimensions are designed by Nichias Corporation to fit to the following flanges.JIS B2220-2004 “Steel welding pipe flanges“JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)JIS B2239-1996 “General rules for cast iron pipe flanges“ (Discontinued)
(2) For bolting material, high-tension bolts such as B7 (SNB7) and above are required.(3) The gasket outer diameter for the types with outer ring indicates the shoulder dimensions of the
gasket excluding spring layers.
Nominal
Pipe
Size
Nominal pressure 10K
Innerdiameter
D2
Inner ringinnerdiameter D1
Outerdiameter
D3
Outer ringouterdiameter D4
Innerdiameter
D2
Inner ringinnerdiameter D1
Outerdiameter
D3
Outer ringouterdiameter D4
Innerdiameter
D2
Inner ringinnerdiameter D1
Outerdiameter
D3
Outer ringouterdiameter D4
16K 20K
Dimension Chart 29
Dimension Chart 30
Unit : A
650A 650 675 725 750 674 699 749 784 695 720 770 805
700 700 726 776 810 716 741 791 836 740 765 815 855
750 752 777 827 870 777 802 852 896 799 824 874 918
800 803 828 878 920 831 856 906 945 865 881 931 978
850 854 879 929 970 880 905 955 995 919 944 994 1,038
900 904 929 979 1,020 934 959 1,009 1,045 971 996 1,046 1,088
1,000 1,006 1,036 1,086 1,124 1,030 1,060 1,110 1,158 ─ ─ ─ ─
1,100 1,108 1,138 1,188 1,234 1,132 1,162 1,212 1,258 ─ ─ ─ ─
1,200 1,209 1,239 1,289 1,344 1,240 1,270 1,320 1,368 ─ ─ ─ ─
1,300 ─ ─ ─ 1,341 1,371 1,421 1,474 ─ ─ ─ ─
1,350 1,362 1,392 1,442 1,498 1,403 1,433 1,483 1,534 ─ ─ ─ ─
1,400 ─ ─ ─ ─ 1,453 1,483 1,533 1,584 ─ ─ ─ ─
1,500 1,514 1,544 1,594 1,658 1,559 1,589 1,639 1,694 ─ ─ ─ ─
Nominal
Pipe
Size
Slip-on Welded Flange A Type
30K
InnerdiameterD2
Inner ring innerdiameter D1
OuterdiameterD3
Outer ringouter diameter D4
For Slip-on Welded Flange A TypeVortex Gasket with Outer and Inner Ring
Dimension Chart 31
For Slip-on Welded Flange B TypeVortex Gasket with Outer and Inner Ring
Unit : A
InnerdiameterD2
Inner ring innerdiameter D1
OuterdiameterD3
Outer ring outerdiameter D4
InnerdiameterD2
Inner ring innerdiameter D1
OuterdiameterD3
Outer ring outerdiameter D4
10A 21.0 29.0 42.0 59.0
15 25.0 32.0 45.0 64.0
20 30.5 37.0 50.0 69.0
25 37.5 47.0 60.0 79.0
32 46.0 54.0 70.0 89.0
40 52.0 64.0 80.0 100.0
50 64.0 75.0 95.0 114.0
65 80.0 100.0 120.0 140.0
80 93.0 110.0 130.0 150.0
90 105.0 120.0 140.0 163.0
100 118.5 130.0 150.0 173.0
125 146.0 160.0 185.0 208.0
150 171.5 190.0 220.0 251.0
200 223.0 235.0 265.0 296.0
250 274.0 290.0 330.0 360.0
300 326.0 350.0 390.0 420.0
350 363.0 395.0 435.0 465.0
400 414.0 445.0 495.0 524.0
Nominal
Pipe
Size
Slip-on Welded Flange B Type
20K 30K
Unit : A
10 23 29 39 52 30 36 46 59
15 27 33 43 57 36 42 52 64
20 33 39 49 62 40 46 56 69
25 38 46 59 74 46 54 67 79
32 47 55 68 84 54 62 75 89
40 53 61 74 89 60 68 81 100
50 64 74 90 104 70 80 96 114
Standard
Dim
ension Charts
99
For JIS Flanges Standard type/VortexTM Gasket with Inner Ring
Notes: (1) This dimension chart is the same as the dimensions shownbelow.
JIS B 2404-2006 “Dimensions of gaskets for pipe flanges”Chart 11 ~ 13
(2) Applicable flanges are Tongue & Groove and Male & Female flanges specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“(Discontinued)
(3) When a Vortex gasket with inner ring is used for slip-on flange, pleasepay attention to the dimensions since the inner diameter of inner ringis small than the flange inner diameter.
(4) For bolting material, high-tension bolts such as B7 (SNB7) and aboveare required.
Nominal
Pipe
Size
For JIS flanges
Tongue & Groove
Standard type Standard type With inner ring
Male & Female
Outer diameter
D3
Inner diameter
D2
Inner ring innerdiameter
D1
Outer diameter
D3
Inner diameter
D2
Outer diameter
D3
Inner diameter
D2
Dimension Chart 32 Unit : A
10A 28 38 25 38 19 25 38
15 32 42 29 42 23 29 42
20 38 50 37 50 31 37 50
25 45 60 44 60 38 44 60
32 55 70 54 70 46 54 70
40 60 75 59 75 51 59 75
50 70 90 70 90 62 70 90
65 90 110 90 110 80 90 110
80 100 120 100 120 90 100 120
90 110 130 110 130 100 110 130
100 125 145 125 145 113 125 145
125 150 175 150 175 138 150 175
150 190 215 187 215 171 187 215
200 230 259 231 259 215 231 259
250 296 324 288 324 268 288 324
300 341 374 338 374 318 338 374
350 381 414 376 414 356 376 414
400 441 474 434 474 409 434 474
Tongue & Groove Male & Female
Sta
ndar
dD
imen
sion
Cha
rts
100
For JIS Flanges NAFLONTM PTFE Cushion Gasket (TOMBO� No.9010-NA-A/B)
Notes: (1) These dimensions were designed by NICHIAS Corporation tofit to JIS B 2238-1996 flanges.
(2) Applicable flanges are those specified in the following standards.JIS B2220-2004 “Steel welding pipe flanges“JIS B2239-2004 “Cast iron pipe flanges“JIS B2240-1996 “General rules for copper alloy pipe flanges“JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“(Discontinued)
(3) Dimensions in brackets are applicable for TOMBO No.9010-NA-A-5/-NA-A-7 and TOMBO No.9010-NA-B-5/-NA-B-7 type.
(4) For B type slip-on flanges as per JIS B 2220, nominal pressure of20K, nominal size of 10~50A gaskets with these dimensions cannotbe used.
A-6 Type, A-8 Type B-6 Type, B-8 Type
Nominal Pipe Size 5K
A BD1 D2
D3 D4
Dimension Chart 33 Unit : A
10K
D3 D4
16K
D3 D4
20K
D3 D4T Type
10 3/8 18 26 42 45 49 53 48 53 49 53
15 1/2 22 30 46 50 54 58 52 58 54 58
20 3/4 28 36 52 55 59 63 58 63 59 63
25 1 35 43 59 65 70 74 70 74 70 74
32 11/4 43 51 71 78 79 84 79 84 79 84
40 11/2 49 57 77 83 84 89 85 89 85 89
50 2 62 69 88 93 99 104 100 104 99 104
65 21/2 78 85 106 118 119 124 116 124 119 124
80 3 91 98 121 129 129 134 135 140 135 140
90 31/2 104 111 134 139 140 144 145 150 148 150
100 4 117 124 145 149 155 159 160 165 163 165
125 5 144 151 178 184 185 190 195 203 198 203
150 6 171 178 205 214 215 220 227 238 233 238
175 7 193 200 229 240 240 245 ─ ─ ─ ─
200 8 219 226 255 260 265 270 275 283 278 283
225 9 244 251 280 285 285 290 ─ ─ ─ ─
250 10 271 278 313 325 321 333 345 356 345 356
300 12 321 328 363 370 370 378 395 406 395 406
350 14 356 363 401 413 415 423 436 450 436 450
400 16 407 414 461 473 471 486 487 510 487 510
450 18 457 464 511 533 530 541 556 575 565 575
500 20 510 517 571 583 583 596 609 630 609 630
550 22 561 568 625 641 635 650 665 684 665 684
600 24 612 619 676 691 684 700 716 734 716 734
650 26 670 674 735 746 740 750 770 784 790 805
700 28 725 729 785 796 800 810 820 836 840 855
750 30 775 779 840 850 855 870 880 896 900 918
800 32 825 829 890 900 905 920 930 945 960 978
850 34 875 879 940 950 955 970 980 995 1,020 1,038
900 36 925 929 990 1,000 1,005 1,020 1,030 1,045 1,070 1,088
1,000 40 1,030 1,034 1,090 1,100 1,110 1,124 1,140 1,158 ─ ─
1,100 44 1,130 1,134 1,200 1,210 1,220 1,234 1,240 1,258 ─ ─
1,200 48 1,230 1,234 1,305 1,320 1,325 1,344 1,350 1,368 ─ ─
1,300 52 1,335 1,339 ─ ─ ─ ─ 1,450 1,474 ─ ─
1,350 54 1,390 1,394 1,460 1,475 1,480 1,498 1,510 1,534 ─ ─
1,400 56 1,435 1,439 ─ ─ ─ ─ 1,560 1,584 ─ ─
1,500 60 1,545 1,549 1,615 1,630 1,635 1,658 1,670 1,694 ─ ─
3.2
(2.8)A Type
3.2
(3.8)
5.0
(3.8)
B Type
Standard
Dim
ension Charts
101
For JIS Flanges NAFLONTM PTFE Cushion Gasket (TOMBO� No.9010-NA-AS)
Nominal Pipe Size 5K
A BD1 D2
D3 D4
Dimension Chart 34 Unit : A
10K
D3 D4
16,20K
D3 D4T Type
10 3/8 26 28 42 45 48 53 48 53
15 1/2 31 33 48 50 52 58 52 58
20 3/4 36 38 52 55 58 63 58 63
25 1 41 43 62 65 70 74 70 74
32 11/4 51 53 72 78 80 84 80 84
40 11/2 56 58 78 83 85 89 85 89
50 2 67 70 88 93 100 104 100 104
65 21/2 92 95 112 118 120 124 120 124
80 3 102 105 125 129 130 134 135 140
90 31/2 112 115 135 139 140 144 145 150
100 4 122 125 145 149 155 159 160 165
125 5 152 155 180 184 185 190 195 203
150 6 187 190 210 214 215 220 230 238
175 7 207 210 235 240 240 245 ─ ─
200 8 232 235 255 260 265 270 275 283
225 9 257 260 280 285 285 290 ─ ─
250 10 297 300 320 325 325 333 345 356
300 12 337 340 365 370 370 378 395 406
350 14 377 380 405 413 415 423 440 450
400 16 427 430 465 473 475 486 495 510
450 18 477 480 525 533 530 541 560 575
500 20 527 530 575 583 585 596 615 630
550 22 577 580 630 641 640 650 670 684
600 24 627 630 680 691 690 700 720 734
3.4
(3.0)
2.5
(2.5)
AS Type
AS-6 Type, AS-8 Type
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to JIS B 2238-1996 flanges.
(2) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2239-2004 “Cast iron pipe flanges“
JIS B2240-1996 “General rules for copper alloy pipe flanges“
JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
(3) Dimensions in brackets are applicable for TOMBO No.9010-NA-AS-5/-NA-AS-7.
(4) For B type slip-on flanges as per JIS B 2220, nominal pressure of 20K, nominal size of 10~50A gaskets with these dimensions cannot beused since inner diameter of gasket is smaller than flange inner diameter.
Sta
ndar
dD
imen
sion
Cha
rts
102
For JIS Flanges NAFLONTM PTFE Cushion Gasket (High temperature applications) (TOMBO� No.9010-NA-A-9)
O.D
T t
I.D
D1
D2D3
D4
Nominal Pipe
Size
10K
Wire mesh
I.D O.DA B
D1 D2D3 D4
16,20K
Wire mesh
I.D O.DD3 D4
Dimension Chart 35 Unit : A
t T Type
(10) 3/8 18 26 49 53 30 47 49 53 30 47
(15) 1/2 22 30 54 58 34 52 54 58 34 52
(20) 3/4 28 36 59 63 40 57 59 63 40 57
25 1 35 43 70 74 47 68 70 74 47 68
32 11/4 43 51 79 84 55 77 79 84 55 77
40 11/2 49 57 85 89 61 83 85 89 61 83
50 2 61 69 99 104 73 97 99 104 73 97
65 21/2 77 85 119 124 89 117 119 124 89 117
80 3 90 98 129 134 102 127 135 140 102 133
90 31/2 103 111 140 144 115 138 148 150 115 146
100 4 116 124 155 159 128 153 163 165 128 161
125 5 143 151 185 190 155 183 198 203 155 196
150 6 170 178 215 220 182 213 233 238 182 231
175 7 192 200 240 245 204 238 ─ ─ 204 ─
200 8 218 226 265 270 230 263 278 283 230 276
225 9 243 251 285 290 255 283 ─ ─ 255 ─
250 10 270 278 321 333 282 319 345 356 282 343
300 12 320 328 370 378 332 368 395 406 332 393
350 14 355 363 415 423 367 413 436 450 367 434
400 16 406 414 471 486 418 469 487 510 418 485
450 18 456 464 530 541 468 528 556 575 468 554
500 20 509 517 583 596 521 581 609 630 521 607
550 22 560 568 635 650 572 633 665 684 572 663
600 24 611 619 684 700 623 682 716 734 623 714
3.92.0A
Type
A Type
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to JIS B 2238-1996 flanges.(2) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“JIS B2239-2004 “Cast iron pipe flanges“JIS B2240-1996 “General rules for copper alloy pipe flanges“JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
(3) These gaskets cannot be used for the following services since inner diameter of gasket is smallerthan flange inner diameter.Slip-on flanges as per JIS B 2220, 10K, 16K and 20K for 10~40A Slip-on flanges as per JIS B 2220, 20K and 30K for 10~65A
Standard
Dim
ension Charts
103
For NAFLONTM Lined Piping NAFLONTM PTFE Cushion Gasket (TOMBO� No.9010-NA-FG-7)
Nominal Pipe Size For JIS 10K
A B D1 D4 t TType
Dimension Chart 36 Unit : A
15 1/2 16 58
20 3/4 22 63
25 1 27 74
40 11/2 45 89
50 2 58 104
65 21/2 71 124
80 3 85 134
100 4 104 159
125 5 128 189
150 6 153 220
200 8 202 270
250 10 251 333
300 12 300 378
1.5 2.3
AS-7 Type
A-7 Type
AS-7 Type A-7 Type
Notes: (1) TOMBO No.9010-NA-FG-7 is a PTFE jacket type gasket used for anti-corrosion NAFLON lined piping.
If a solid type product is required, please use the TOMBO No.9007 NAFLON PTFE cut gasket or TOMBO No.9007-LCNAFLON Low creap gasket.
For D1, D4 and t, follow same dimensions as above chart.
(2) Applicable flanges are JIS 10K flanges for NAFLON lined piping, 15A-300A
NAFLON PTFE Cut Gasket(TOMBO No.9007)
NAFLON Low Creap Gasket(TOMBO No.9007-LC)
For JIS Flanges NAFLONTM PTFE Cushion Gasket (Outer periphery seald)(TOMBO� No.9010-NA-R-A)
104
Sta
ndar
dD
imen
sion
Cha
rts
Dimension Chart 37 Unit : A
Nominal Pipe Size
A
010
015
020
025
032
040
050
065
080
090
100
125
150
175
200
225
250
300
350
400
450
500
550
600
D1
013
017
022
028
036
042
053
066
079
091
103
135
162
184
210
236
270
316
351
410
455
511
564
616
D2
020
024
029
t1
2.0
(2.4)
t2
2.8
(3.2)
035
043
049
060
073
086
098
110
142
169
191
217
243
277
323
358
417
462
518
571
623
D3
Nominal Pressure
5K
033
038
043
053
066
071
081
106
117
127
137
172
202
228
248
273
313
358
401
461
521
571
629
679
10K
041
046
051
062
072
077
092
112
122
132
147
178
208
233
258
278
321
366
411
474
529
584
638
688
D4
Nominal Pressure
5K
045
050
055
065
078
083
093
118
129
139
149
184
214
240
260
285
325
370
413
473
533
583
641
691
10K
053
058
063
074
084
089
104
124
134
144
159
190
220
245
270
290
333
378
423
486
541
596
650
700
D4
t2
D3
D1
D2
t1
D4
t2
D3
D1
D2
t1
A-7 Type A-8 Type
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to JIS B 2238-1996 flanges.
(2) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2239-2004 “Cast iron pipe flanges“
JIS B2240-1996 “General rules for copper alloy pipe flanges“
JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
(3) Dimension in brackets are applicable for TOMBO No.9010-NA-A-6/-NA-A-8.
For JIS Flanges NAFLONTM PTFE Cushion Gasket (Outer periphery seald)(TOMBO� No.9010-NA-R-AS)
105
Standard
Dim
ension Charts
Dimension Chart 38 Unit : A
Nominal Pipe Size
A
010
015
020
025
032
040
050
065
080
090
100
125
150
175
200
225
250
300
350
400
450
500
550
600
D1
013
017
022
028
036
042
053
066
079
091
103
143
179
198
224
249
292
332
372
425
475
525
574
624
D2
016
020
025
t1
2.0
(2.4)
t2
2.8
(3.2)
031
039
045
056
069
082
094
106
146
182
201
227
252
295
335
375
428
478
528
577
627
D3
Nominal Pressure
5K
033
038
043
053
066
071
081
106
117
127
137
172
202
228
248
273
313
358
401
461
521
571
629
679
10K
041
046
051
062
072
077
092
112
122
132
147
178
208
233
258
278
321
366
411
474
529
584
638
688
D4
Nominal Pressure
5K
045
050
055
065
078
083
093
118
129
139
149
184
214
240
260
285
325
370
413
473
533
583
641
691
10K
043
058
063
074
084
089
104
124
134
144
159
190
220
245
270
290
333
378
423
486
541
596
650
700
D4
t2
D3
D1
D2
t1
D4
t2
D3
D1
D2
t1
AS-7 Type AS-8 Type
Notes: (1) These dimensions are designed by NICHIAS Corporation to fit to JIS B 2238-1996 flanges.
(2) Applicable flanges are those specified in the following standards.
JIS B2220-2004 “Steel welding pipe flanges“
JIS B2239-2004 “Cast iron pipe flanges“
JIS B2240-1996 “General rules for copper alloy pipe flanges“
JIS B2241-1986 “Basic dimensions of aluminum alloy pipe flanges“
JIS B2238-1996 “General rules for steel welding pipe flanges“ (Discontinued)
(3) Dimension in brackets are applicable for TOMBO No.9010-NA-AS-6/-NA-AS-8.
Sta
ndar
dD
imen
sion
Cha
rts
106
JIS 10K Plastic Flanges EbilonTM Gasket
Nominal Pipe Size Gaskets
A B
Outerdiameter
A
Innerdiameter
B
Seal section diameter Bolts
C D PCD n-φk
Reference
E
Thickness
T
Dimension Chart 39 Unit : A
15 1/2B 93 18 5 26 41 70 4-15 53
20 3/4 98 22 5 32 47 75 4-15 58
25 1 123 30 5 38 53 90 4-19 68
30 11/4 133 37 5 50 65 100 4-19 78
40 11/2 138 43 5 54 69 105 4-19 82
50 2 153 54 5 68 83 120 4-19 96
65 21/2 173 69 5 86 101 140 4-19 116
80 3 183 80 5 98 112 150 8-19 124
100 4 208 102 5 120 138 175 8-19 150
125 5 248 127 5 145 166 210 8-23 180
150 6 278 150 5 168 190 240 8-23 210
200 8 328 198 5 216 247 290 12-23 260
250 10 398 249 5 270 306 355 12-25 326
300 12 443 300 5 324 352 400 16-25 372
Notes: (1) Applicable gaskets are Ebilon Gaskets TOMBO No.9013, 9013-D , 9013-EP and 9013-DEP.
(2) These dimensions are designed by NICHIAS Corporation to fit to plastic flanges based on JIS B 2210 10K.
(3) Applicable flanges are 10K plastic (PVC) flanges manufactured by Kubota Corp., Sekisui Chemical Co., Ltd.,
Asahi Organic Chemicals Industry Co., Ltd., etc.
(4) When these gaskets are used for JIS B 2210 and B 2220 flanges, the sealing section may be smaller than the flange inner diameter.
FOR JIS 10K Flanges Electrical Insulation Bolt Kit (TOMBO� No.9910/9910H, TOMBO� No.9011-NA-E5)
107
Standard
Dim
ension Charts
Dimension Chart 40 Unit : A
Nominal pipe size Insulation bolt Hexagonal
nutInsulating washerMetal washer Insulating gasket Number
of bolts
Width ofRingA
Width ofRingd1
Width ofRingL
Width ofRingRs
t
TOMBO No.9910
TOMBO No.9910-H
Width ofRingH
Width ofRingd2
Width ofRingD2
Width ofRingt1
Width ofRingt2
Width ofRingd3
Width ofRingD5
Width ofRingt3
Width ofRingN
10152025324050658090100 125 150 175 200 225 250300350400450500550 60065070075080085090010001100120013501500
M12M12M12M16M16M16M16M16M16M16M16M20M20M20M20M20M22M22M22M24M24M24M30×3M30×3M30×3M30×3M30×3M30×3M30×3M30×3M36×3M36×3M36×3M42×3M42×3
7070758085858590909090105 105 105 105 105 120120125130135135150150150150160160160160180180185205205
363639404343434848484855555555556262677277778282828286868686929297110110
0.7
1.0
1010101313131313131313161616161618181819191924242424242424242929293434
13.013.013.017.017.017.017.017.0 17.017.017.021.021.021.021.021.023.023.023.025.025.025.031.031.031.031.031.031.031.031.037.037.037.043.043.0
2424243030303030303030373737373739393944444456565656565656566666667878
44444444444444446666666666666666666
2.52.52.53.03.03.03.03.03.03.03.03.03.03.03.03.03.03.03.04.04.04.04.04.04.04.04.04.04.04.05.05.05.07.07.0
13162227364558768596104 129 153 178 202 225 251 300 373423 473 523573 623 670 725 775 825 875 925 1,030 1,130 1,230 1,390 1,545
535863748489104 124 134 144 159 190 220 245 270 290 333 378 423 486 541 596 650 700 750 810 870 920 970 1,020 1,124 1,234 1,344 1,498 1,658
2.52.52.52.5 2.5 2.5 3.0 3.0 3.0 3.0 3.03.03.03.03.03.03.03.03.03.03.03.03.03.03.83.83.83.83.83.83.83.83.83.83.8
WidthRingtype
A
444444448888812121212161616202020242424242828282828323640
*This table is applicable for the flanges specified in JIS B2238.
*If higt nut such as the one whose height is greater or equal th the nominal diameter of bolt is used, the length of bolt should be greater accordingly.
*If there is possibility that scale in the fluid may cause electrical conducting, please consult with us. We would design gasket in special size.
*The size of TOMBO No.9910 is the same as that of TOMBO No.9910-H except for "t" that stands for the thickness of insulating sleeve.
*If service temperature is over 150℃, TOMBO No.9910-H/9007-LC should be used. Please consult with us about the size of the TOMBO No.9007-LC.
1.5
B
d1
rs
L
t
H
d1D2d2
t2
Metal
D2d2
t1
Insulationt3
d3D5
d3D5
t3t3
Insulation bolt Hexagonal nut Insulating washerMetal washer
Insulating gasket
108
Sta
ndar
dD
imen
sion
Cha
rts
FOR JIS 20K Flanges Electrical Insulation Bolt Kit(TOMBO� No.9910/9910H, TOMBO� No.9011-NA-E5)
Dimension Chart 41 Unit : A
Nominal pipe size Insulation bolt Hexagonal
nutInsulating washerMetal washer Insulating gasket Number
of bolts
Width ofRingA
Width ofRingd1
Width ofRingL
Width ofRingRs
t
TOMBO No.9910
TOMBO No.9910-H
Width ofRingH
Width ofRingd2
Width ofRingD2
Width ofRingt1
Width ofRingt2
Width ofRingd3
Width ofRingD5
Width ofRingt3
Width ofRingN
10152025324050658090100 125 150 200 250300350400450500550 600650700750800850900
M12M12M12M16M16M16M16M16M20M20M20M22M22M22M24M24M30×3M30×3M30×3M30×3M36×3M36×3M45×3M45×3M52×3M52×3 M52×3 M52×3
70707580858585 90100110 110125 125 125145145170 175 190 190 210 210 240 240 270 270 280 280
3636394043434348525656696969838396101 112112 120 120 140 140 154 154 162 162
0.7
1.0
10101013131313131616161818181919242424242929363642424242
13.013.013.017.017.017.017.017.021.021.021.023.023.023.025.025.031.031.031.031.037.037.046.046.054.054.054.054.0
24242430303030303737373939394444565656566666858598989898
4444444444466666666666666666
2.52.52.53.03.03.03.03.03.03.03.03.03.03.04.04.04.04.04.04.05.0 5.0 7.0 7.0 8.0 8.0 8.0 8.0
13162227364558768596104 129 153 202 280 320 373 423 473 523573 623 670 725 775 825 875 925
535863748489104 124 140 150 165 203 238 283 356 406 450 510 575 630 684 734 805 855 918 978 1,038 1,088
2.52.52.52.52.52.53.03.03.03.03.03.03.03.03.03.03.03.03.03.03.03.03.83.83.83.83.83.8
WidthRingtype
A
44444488888812121216161620202024242424242428
*This table is applicable for the flanges specified in JIS B2238.
*If higt nut such as the one whose height is greater or equal th the nominal diameter of bolt is used, the length of bolt should be greater accordingly.
*If there is possibility that scale in the fluid may cause electrical conducting, please consult with us. We would design gasket in special size.
*The size of TOMBO No.9910 is the same as that of TOMBO No.9910-H except for "t" that stands for the thickness of insulating sleeve.
*If service temperature is over 150℃, TOMBO No.9910-H/9007-LC should be used. Please consult with us about the size of the TOMBO No.9007-LC.
1.5B
d1
rs
L
t
H
d1D2d2
t2
Metal
D2d2
t1
Insulationt3
d3D5
d3D5
t3t3
Insulation bolt Hexagonal nut Insulating washerMetal washer
Insulating gasket
Gaskets
INDEX
110
NU
ME
RIC
AL
IND
EX
1050 Rubber Cut Gasket 561051 Cloth Reinforced Rubber Cut Gasket 561120 CLINSIL-Top 61200 Graseal Gasket 401210-A Graseal Gasket MI-A 401215 Graseal Gasket PM 401215-A Graseal Gasket PM-A 401220 Graseal Gasket Tape (Plain) 411221 Graseal Gasket Tape (Crinkled) 411364 NA Gasket Tape 551368 NA Tadpole Gasket Tape 551368-G NA Tadpole Gasket Tape (Finished with graphite) 551374 NA Manhole Gasket 541374-G NA Manhole Gasket (Treated with graphite) 541378 NA Gasket with core 541400-ST Super Manhole Gasket-ST 541400-TH FF Manhole Gasket 541400-THG FF Manhole Gasket (Treated with graphite) 541600 Metakote 591608 Metafoam 591804-GR Series Graseal Vortex Gasket 141804-NA Series NA Vortex Gasket 141806-GH Series Vortex Gasket-GH 161806-GM Series Vortex Gasket-GM 161806-GS Series Vortex Gasket-GS 161809 Series Graseal Vortex Gasket L 171809-AL Series Graseal Vortex Gasket for Aluminum Flanges 171841 NA Metal Jacketed Gasket 371841-FI NA Metal Jacketed Gasket for High-temperature Applications 371850 Double Cone Gasket 321850 Brigeman Gasket 321850-BX BX Ring Gasket 321850-C Octagonal Ring Joint Gasket 311850-D Delta Gasket 321850-L Lens type Gasket 321850-O Metal O-Ring 321850-P Plain Metal Gasket 301850-RX RX Ring Gasket 321850-V Oval Ring Joint Gasket 311861 NA Corrugated Metal Jacketed Gasket 371861-FI NA Corrugated Metal Jacketed Gasket for High-temperature Applications 371880-GR CMGC Gasket 371890 Serrated Metal Gasket 301938 CLINSIL-UF 81991-NF CLINSIL-NF 81993 CLINSIL-Super 71995 CLINSIL-Brown 7
2670 Rubber O-Ring 56
6526 NA Beater Sheet 596750-P Vermosul Sheet-P 59
6000~
2000~
1000~
9007 NAFLON PTFE Cut Gasket 429007-FD NAFLON FD Gasket 449007-G20 NAFLON PTFE Glass Fiber Filled Cut Gasket 429007-GL NAFLON PTFE Special Filler Filled Cut Gasket (Soft) 449007-LC NAFLON PTFE Low Creep Gasket 439007-LP NAFLON PFA Gasket 459007-SC NAFLON PTFE Special Filler Filled Cut Gasket 439010 NAFLON PTFE Cushion Gasket 46-499010-NA-E5 Electrical Insulation Gasket 519013 Ebilon Gasket (PTFE Jacketed) 579013-D Ebilon Gasket (PTFE Jacketed) for Electrolytic Cells 579013-DEP Ebilon Gasket (Solid Rubber) for Electrolytic Cells 579013-EP Ebilon Gasket (Solid Rubber) 579014 Saniclean Gasket 589022-A NAFLON PTFE Covered Rubber O-Ring 529022-PFA NAFLON PFA Covered Rubber O-Ring 529028 NAFLON PTFE O-Ring 529037 NAFLON SP Packing 529090 Series NAFLON Vortex Gasket 159094 NAFLON Manhole Gasket 549096 NICHIAS Soft Seal 529105 Aqua-tight Paste 609106 Oil-tight Paste 609120 Anti-corrosion Paste 609200P Standard Type Metal O-Seal 349200V Vent Hole Type Metal O-Seal 349400 NAFLON Paste 619401 PTFE Grease 619910 NAFLON PVDF Electrical Insulation Bolt Kit 509910-H NAFLON PTFE Electrical Insulation Bolt Kit 50
Irregular-shape Vortex Gasket 18Heat Exchanger Vortex Gasket with Pass Ribs 18Special Construction Vortex Gasket 19Metal Jacketed Gaskets with Graseal Tape 38Heat Exchanger Gasket 38
Other
9000~
■NUMERICAL INDEX
TOMBO No. Product Name Page TOMBO No. Product Name Page
111
NU
ME
RIC
AL IN
DE
X
Anti-corrosion Paste 9120 60Aqua-tight Paste 9105 60
Brigeman Gasket 1850 32BX Ring Gasket 1850-BX 32
CLINSIL-Brown 1995 7CLINSIL-NF 1991-NF 8CLINSIL-Super 1993 7CLINSIL-Top 1120 6CLINSIL-UF 1938 8Cloth Reinforced Rubber Cut Gasket 1051 56CMGC Gasket 37
Delta Gasket 1850-D 32Double Cone Gasket 1850 32
Ebilon Gasket (PTFE Jacketed) 9013 57Ebilon Gasket (PTFE Jacketed) for Electrolytic Cells 9013-D 57Ebilon Gasket (Solid Rubber) 9013-EP 57Ebilon Gasket (Solid Rubber) for Electrolytic Cells 9013-DEP 57Electrical Insulation Gasket 9010-NA-E5 51
FF Manhole Gasket 1400-TH 54FF Manhole Gasket (Treated with graphite) 1400-THG 54
Graseal Gasket 1200 40Graseal Gasket MI-A 1210-A 40Graseal Gasket PM 1215 40Graseal Gasket PM-A 1215-A 40Graseal Gasket Tape (Crinkled) 1221 41Graseal Gasket Tape (Plain) 1220 41Graseal Vortex Gasket 1804-GR Series 14Graseal Vortex Gasket for Aluminum Flanges 1809-AL Series 17Graseal Vortex Gasket L 1809 Series 17
Heat Exchanger Gasket 38Heat Exchanger Vortex Gasket with Pass Ribs 18
Irregular-shape Vortex Gasket 18
Lens type Gasket 1850-L 32
Metakote 1600 59Metafoam 1608 59Metal Jacketed Gaskets with Graseal Tape 38Metal O-Ring 1850-O 32
M
L
I
H
G
F
E
D
C
B
A
NA Beater Sheet 6526 59NA Corrugated Metal Jacketed Gasket 1861 37NA Corrugated Metal Jacketed Gasket for High-temperature Applications 1861-FI 37NA Gasket Tape 1364 55NA Gasket with core 1378 54NA Manhole Gasket 1374 54NA Manhole Gasket (Treated with graphite) 1374-G 54NA Metal Jacketed Gasket 1841 37NA Metal Jacketed Gasket for High-temperature Applications 1841-FI 37NA Tadpole Gasket Tape 1368 55NA Tadpole Gasket Tape (Finished with graphite)1368-G 55NA Vortex Gasket 1804-NA Series 14NAFLON FD Gasket 9007-FD 44NAFLON Manhole Gasket 9094 54NAFLON Paste 9400 61NAFLON PFA Covered Rubber O-Ring 9022-PFA 52NAFLON PFA Gasket 9007-LP 45NAFLON PTFE Covered Rubber O-Ring 9022-A 52NAFLON PTFE Cushion Gasket 9010 46-49NAFLON PTFE Cut Gasket 9007 42NAFLON PTFE Electrical Insulation Bolt Kit 9910-H 50NAFLON PTFE Glass Fiber Filled Cut Gasket 9007-G20 42NAFLON PTFE Low Creep Gasket 9007-LC 43NAFLON PTFE O-Ring 9028 52NAFLON PTFE Special Filler Filled Cut Gasket 9007-SC 43NAFLON PTFE Special Filler Filled Cut Gasket (Soft) 9007-GL 44NAFLON PVDF Electrical Insulation Bolt Kit 9910 50NAFLON SP Packing 9037 52NAFLON Vortex Gasket 9090 Series 15NICHIAS Soft Seal 9096 52
Octagonal Ring Joint Gasket 1850-C 31Oil-tight Paste 9106 60Oval Ring Joint Gasket 1850-V 31
Plain Metal Gasket 1850-P 30PTFE Grease 9401 61
Rubber Cut Gasket 1050 56Rubber O-Ring 2670 56RX Ring Gasket 1850-RX 32
Saniclean Gasket 9014 58Serrated Metal Gasket 1890 30Special Construction Vortex Gasket 19Standard Type Metal O-Seal 9200P 34Super Manhole Gasket-ST 1400-ST 54
Vent Hole Type Metal O-Seal 9200V 34Vermosul Sheet-P 6750-P 59Vortex Gasket-GH 1806-GH Series 16Vortex Gasket-GM 1806-GM Series 16Vortex Gasket-GS 1806-GS Series 16
V
S
R
P
O
N
■ALPHABETICAL INDEX
Product Name TOMBO No. Page Product Name TOMBO No. Page
Printed in Japan on Recycled paper E03-0901-01-FT-BU-RE-0703
top related