future mill series for mold making fmr p-positivekorloy.us/pdf/tech news/fmr p-posi.pdf · future...
Post on 09-May-2018
219 Views
Preview:
TRANSCRIPT
FMR P-positiveFuture Mill series for mold making
• Stable clamping system enables stable machining and productivity.• Varied product line-up ensures wide application range.• Optimal shape and grade with high hardness for hard-to-cut material
machining.
High rigidity and revolution-prevention technology
Quality, Performance, Value - Guaranteed!
Recommended cutting condition
• P-positive relief angle (11˚) ensures high rigidity and high machinability in die steel and high-resistant alloy machining.• Flat clearance face of insert prevents interference and revolution while machining.• Optimal grades and chip breakers for various workpieces
•��Chip breaker - Concave shape ensures wide chip pocket
and lowers cutting temperature.
•��Clearance face for preventing rotation - Prevents rotation in machining. - Divides corners. - Prevents interference in high-feed machining. - Ensures stable clamping.
Features
✽Recommended chip breaker : ● First ◦Second
Usage and features of chip breakers
•��Through-coolant system - Superb chip evacuation - Low cutting heat ensures long tool life.
FMR P-positive
02_ KORLOY TECH-NEWS
Optimal cutting edge for aluminum machining and buffedsurface ensure high machinability.
Chip breaker for low cutting resistance enables fine finishing.
Excellent results in titanium machining thanks to a high hardness cutting edge and the chip breaker reducing the cutting load.
Optimal for general machining
Optimal for high hardness die steel and heat resistant alloy
MA
MF
ML
MM
None C/B
Chip breaker Cutting edge FeaturesApplications
Aluminum machining
Fine finishing
Titanium
General machining
Super hard material machining
WorkpieceCutting conditions Chip breaker
None C/B
P
MKN
Heat resistant alloyS
vc(sfm)
ae(inch)
328~656 0.7D~0.1D590~951 0.7D~0.1D
164~492 0.7D~0.1D426~820 0.7D~0.1D
164~492 0.7D~0.1D426~820 0.7D~0.1D
164~492 0.7D~0.1D
328~820 0.7D~0.1D328~722 0.7D~0.1D
328~492 0.7D~0.1D
394~689 0.7D~0.1D
Low alloy steel
Low pre-hardened steel
High alloy steel
High pre-hardened steel
Low carbon steelHigh carbon steel
Stainless steelGray cast iron, Ductile cast iron
Aluminum 984~2,625 0.7D~0.1DFe 115~197 0.7D~0.1D
Ni or Co 98~164 0.7D~0.1D
Titanium 131~230 0.7D~0.1D
Under HRC27
HRC20~50
Under HRC27
Hardness
HRC20~48
HB80~180HB180~280
Under HB270Under 350MPa
-HRC20~30HRC40~45HRC35~45
Over HRC50
Grade
PC5400 / PC5300PC3600
PC5300PC3600
PC5300PC3600
PC5300
PC5400PC5400
PC5300 / PC5400PC5300
H01PC5300 / PC5400PC5300 / PC5400PC5300 / PC5400PC5300 / PC5400 98~164 0.7D~0.1D
ap(inch)
0.012~0.2360.012~0.236
~0.020~0.020
~0.020~0.020
~0.020
0.012~0.2360.012~0.236
0.012~0.236
0.012~0.2360.012~0.236
~0.020~0.020
~0.059~0.020
MA
--
--
--
-
--
--●----
ML
--
--
--
-
--
-----
●-
2
--
◦◦
--
◦
--
------◦
1
◦◦
●●
◦◦
●
--
---●●-●
MF
--
--
--
-
●●
◦◦---
◦-
MM
●●
--
●●
-
◦◦
●●-◦◦--
0.008~0.0240.008~0.024
0.012~0.0200.012~0.020
0.012~0.0200.012~0.020
0.012~0.020
0.005~0.0280.005~0.028
0.008~0.024
fz(ipt)
0.008~0.0240.012~0.0240.012~0.0200.012~0.020
0.012~0.0200.012~0.020High hardened materialsH
FMR P-positive _03
Feed per tooth according to ap(fz, ipt)
RPMT08
RPMT10
RPMT12
RPMT16
RPMT20
8
10
12
16
20
0.012
0.016
0.024
0.026
0.028
0.009
0.011
0.018
0.018
0.020
0.007
0.010
0.014
0.016
0.017
0.006
0.008
0.012
0.013
0.014
-
0.005
0.010
0.012
0.013
-
-
0.008
0.011
0.011
-
-
-
0.009
0.010
-
-
-
-
0.009
Insert Insert size(d)
Feed per tooth according to ap
ap=0.039 ap=0.079 ap=0.118 ap=0.157 ap=0.197 ap=0.236 ap=0.315 ap=0.394
Cutting performace
• Cutting conditions vc(sfm) = 820 fz(ipt) = 0.024 ap(inch) = 0.039 wet
• Tools Insert RPMT1204M0E-MF(PC5300) Cutter FMRSA4125HRP-3L100
•�Result
Carbon steel (SM490A Heat treatment, HRC 38~40)P
190%
100%
RPMT-MF
Competitor’s
Tool life(%)
1.9timesmore
• Cutting conditions vc(sfm) = 584 fz(ipt) = 0.028 ap(inch) = 0.059 dry
• Tools Insert RPMT1606M0S-MM(PC5300) Cutter FMRCA5250HRP-4
•�Result
Alloy steel (KP4M Heat treatment, HRC 30~45)P
150%
100%
RPMT-MM
Competitor’s
Tool life(%)
1.5timesmore
• Cutting conditions vc(sfm) = 584 fz(ipt) = 0.029 ap(inch) = 0.031 dry
• Tools Insert RPMT1204M0E-MF(PC5300) Cutter FMRCA4250HRP-6
•�Result
Alloy steel (KP1, HRC 28~33)P
120%
100%
RPMT-MF
Competitor’s
Tool life(%)
1.2timesmore
• Cutting conditions vc(sfm) = 164 fz(ipt) = 0.006 ap(inch) = 0.157 dry
• Tools Insert RPMW1204M0S1(PC5300) Cutter FMRSA4125HRP-3L100
•�Result
Alloy steel (STD61, HRC 50~52)P
130%
100%
RPMW
Competitor’s
Tool life(%)
1.3timesmore
(inch)
Quality, Performance, Value - Guaranteed!
FMR P-positiveAvailable Inserts
Parts
Type
FTNA0305FTNA0306
FTGA03507FTGA03508FTKA0408FTKA0410
FTGA0511-PFTKA0615-P
TW09S
TW15S
TW15S
--
-
-
-
TW20-100TW25-100
Ø0.6875Ø0.75~Ø1.5
Ø0.75~Ø1.0625Ø1.25~Ø2.5
Ø1.00~Ø1.0625Ø1.25~Ø4.00
Ø1.5~Ø6.0Ø2.0~Ø10.0
2500 type
3000 type
4000 type
5000 type6000 type
Screw Wrench Wrench Cutter Dia.
04_ KORLOY TECH-NEWS
RPCT
RPET
RPMT
RPMT
RPMW
10T3M0-MA1204M0-MA1606M0-MA2007M0-MA1204M0-ML2007M0-ML
0803M0E-MF10T3M0E-MF1204M0E-MF1606M0E-MF2007M0E-MF0803M0S-MM10T3M0S-MM1204M0S-MM1606M0S-MM2007M0S-MM0803M0E110T3M0E11204M0S11204M0S21606M0S12007M0S1
Designation Usage Cutter Configuration
Dimensions (inch)Coated Uncoated
PC53
00
PC36
00
PC54
00
H01 d
for Aℓ machiningfor Aℓ machiningfor Aℓ machiningfor Aℓ machining
for Titanium machningfor Titanium machning
for Low cutting resistance machiningfor Low cutting resistance machiningfor Low cutting resistance machiningfor Low cutting resistance machiningfor Low cutting resistance machiningwith Stronger cutting edgewith Stronger cutting edgewith Stronger cutting edgewith Stronger cutting edgewith Stronger cutting edgefor High hardness material machiningfor High hardness material machiningfor High hardness material machining
for High hardness material machiningfor High hardness material machining
3000 type4000 type5000 type6000 type4000 type6000 type
2500 type3000 type4000 type5000 type6000 type2500 type3000 type4000 type5000 type6000 type2500 type3000 type4000 type4000 type5000 type6000 type
-
-
-
-
-
-
-
-
●●●●●●●●●●-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
●●●●-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
●●●●●●●●●●●●●●●●
-
-
-
-
-
-
-
-
●●●●●●●●●●●●●●●●
0.394 0.472 0.630 0.787 0.4720.787
0.315 0.394 0.472 0.630 0.787 0.315 0.394 0.472 0.630 0.787 0.315 0.394 0.472 0.472 0.630 0.787
t
0.156 0.187 0.250 0.276 0.1870.276
0.125 0.156 0.187 0.250 0.276 0.125 0.156 0.187 0.250 0.276 0.125 0.156 0.187 0.187 0.250 0.276
0.157 0.177 0.217 0.276 0.1770.276
0.134 0.157 0.177 0.217 0.276 0.134 0.157 0.177 0.217 0.276 0.134 0.157 0.177 0.177 0.217 0.276
d1
RPCT-MA
RPMT-MF
RPMT-MM
RPMW
RPCT-MA
RPMT-MF
RPMT-MM
RPMW
RPCT-MA
RPMT-MF
RPMT-MM
RPMW
RPCT-MA
RPMT-MF
RPMT-MM
RPMWML Chip breaker inventory is being prepared at the moment and pre-orders can be made in advance.
for High hardness material machining(with Stronger cutting edge)
FMR P-positive _05
Maximum angle table for Ramping machining
FMR2500
FMR3000
FMR4000
FMR5000
FMR6000
0.315 0.315 0.315 0.315 0.315 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.630 0.630 0.630 0.630 0.630 0.630 0.630 0.787 0.787 0.787 0.787 0.787 0.787 0.787 0.787
0.688 0.750 0.813 1.000 1.063 1.000 1.063 1.250 1.313 1.500 2.000 2.500 1.000 1.063 1.250 1.313 1.500 2.000 2.500 3.000 4.000 1.500 2.000 2.500 3.000 4.000 5.000 6.000 2.000 2.500 3.000 4.000 5.000 6.000 8.000
10.000
17.463 19.050 20.63825.40026.98825.40026.988 31.750 33.338 38.100 50.800 63.500 25.400 26.988 31.750 33.338 38.100 50.800 63.500 76.200
101.600 38.100 50.800 63.500 76.200
101.600 127.000 152.400 50.800 63.500 76.200
101.600 127.000 152.400 203.200 254.000
4.44 17.30 14.40 9.54 8.57
13.30 11.67 8.52 7.82 6.26 4.09 3.03 4.34 3.76
14.94 13.49 10.44 6.49 4.71 3.69 2.58
20.01 10.99 7.54 5.73 3.87 2.92 2.35
17.22 10.99 8.04 5.23 3.87 3.07 2.18 1.68
1.013 0.253 0.307 0.468 0.522 0.333 0.381 0.525 0.574 0.718 1.102 1.487 1.038 1.198 0.295 0.328 0.427 0.692 0.957 1.221 1.750 0.216 0.406 0.595 0.784 1.163 1.542 1.921 0.254 0.406 0.557 0.860 1.163 1.466 2.072 2.678
1.266 0.316 0.383 0.585 0.653 0.416 0.477 0.657 0.717 0.897 1.378 1.859 1.297 1.498 0.369 0.410 0.534 0.865 1.196 1.526 2.188 0.270 0.507 0.744 0.981 1.454 1.927 2.401 0.318 0.507 0.696 1.075 1.454 1.833 2.590 3.348
1.520 0.379 0.460 0.703 0.783 0.500 0.572 0.788 0.860 1.077 1.654 2.230 1.557 1.797 0.443 0.492 0.641 1.038 1.435 1.832 2.625 0.324 0.608 0.893 1.177 1.745 2.313 2.881 0.381 0.608 0.836 1.290 1.745 2.199 3.108 4.018
1.773 0.442 0.537 0.820 0.914 0.583 0.667 0.920 1.004 1.256 1.929 2.602 1.816 2.097 0.517 0.574 0.748 1.211 1.674 2.137 3.063 0.378 0.710 1.041 1.373 2.036 2.698 3.361 0.445 0.710 0.975 1.505 2.036 2.566 3.627 4.687
2.026 0.506 0.613 0.937 1.044 0.666 0.762 1.051 1.147 1.435 2.205 2.974 2.076 2.396 0.590 0.656 0.855 1.384 1.913 2.442 3.500 0.432 0.811 1.190 1.569 2.326 3.084 3.842 0.508 0.811 1.114 1.720 2.326 2.932 4.145 5.357
-----
0.833 0.953 1.314 1.434 1.794 2.756 3.717 2.594 2.995 0.738 0.821 1.069 1.730 2.391 3.053 4.375 0.541 1.014 1.488 1.961 2.908 3.855 4.802 0.635 1.014 1.393 2.150 2.908 3.666 5.181 6.696
------------
3.113 3.594 0.886 0.985 1.282 2.076 2.870 3.663 5.251 0.649 1.217 1.785 2.353 3.490 4.626 5.762 0.762 1.217 1.671 2.581 3.490 4.399 6.217 8.035
---------------------
0.865 1.623 2.380 3.138 4.653 6.168 7.683 1.016 1.623 2.229 3.441 4.653 5.865 8.289
10.713
----------------------------
1.271 2.028 2.786 4.301 5.816 7.331
10.361 13.392
0.507 0.126 0.153 0.234 0.261 0.167 0.191 0.263 0.287 0.359 0.551 0.743 0.519 0.599 0.148 0.164 0.214 0.346 0.478 0.611 0.875 0.108 0.203 0.298 0.392 0.582 0.771 0.960 0.127 0.203 0.279 0.430 0.582 0.733 1.036 1.339
Section Insert size(d)
Tool Dia.(ØD)
ØD(Inch) ØD(mm)Ramping angle
α°(max)Cutting length L(inch) by ap
ap=0.079 ap=0.098 ap=0.118 ap=0.138 ap=0.157 ap=0.197 ap=0.236 ap=0.315 ap=0.394ap=0.039
※ L(inch) : Cutting length α˚ : Max. ramping angle ap(inch) : Depth of cut
L =ap
tan α˚ (inch)
(inch)
RPCT-MA
RPMT-MF
RPMT-MM
RPMW
Insert size(d): Please refer page 4, applicable insert drawing.
Quality, Performance, Value - Guaranteed!
FMR P-positive
06_ KORLOY TECH-NEWS
Minimum hole diameter table for Helical machining(ØDHmin)
FMR2500
FMR3000
FMR4000
FMR5000
FMR6000
0.315 0.315 0.315 0.315 0.315 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.630 0.630 0.630 0.630 0.630 0.630 0.630 0.787 0.787 0.787 0.787 0.787 0.787 0.787 0.787
0.688 0.750 0.813 1.000 1.063 1.000 1.063 1.250 1.313 1.500 2.000 2.500 1.000 1.063 1.250 1.313 1.500 2.000 2.500 3.000 4.000 1.500 2.000 2.500 3.000 4.000 5.000 6.000 2.000 2.500 3.000 4.000 5.000 6.000 8.000
10.000
17.463 19.050 20.638 25.400 26.988 25.400 26.988 31.750 33.338 38.100 50.800 63.500 25.400 26.988 31.750 33.338 38.100 50.800 63.500 76.200
101.600 38.100 50.800 63.500 76.200
101.600 127.000 152.400 50.800 63.500 76.200
101.600 127.000 152.400 203.200 254.000
4.44 17.30 14.40 9.54 8.57
13.30 11.67 8.52 7.82 6.26 4.09 3.03 4.34 3.76
14.94 13.49 10.44 6.49 4.71 3.69 2.58
20.01 10.99 7.54 5.73 3.87 2.92 2.35
17.22 10.99 8.04 5.23 3.87 3.07 2.18 1.68
1.06 1.19 1.31 1.69 1.81 1.61 1.73 2.11 2.23 2.61 3.61 4.61 1.53 1.65 2.03 2.15 2.53 3.53 4.53 5.53 7.53 2.37 3.37 4.37 5.37 7.37 9.37
11.37 3.21 4.21 5.21 7.21 9.21
11.21 15.21 19.21
0.37 0.44 0.50 0.69 0.75 0.61 0.67 0.86 0.92 1.11 1.61 2.11 0.53 0.59 0.78 0.84 1.03 1.53 2.03 2.53 3.53 0.87 1.37 1.87 2.37 3.37 4.37 5.37 1.21 1.71 2.21 3.21 4.21 5.21 7.21 9.21
0.152 0.130 0.114 0.083 0.076 0.093 0.085 0.066 0.062 0.051 0.035 0.027 0.107 0.096 0.073 0.067 0.055 0.037 0.028 0.022 0.016 0.065 0.041 0.030 0.024 0.017 0.013 0.011 0.047 0.033 0.026 0.018 0.013 0.011 0.008 0.006
-0.163 0.142 0.103 0.095 0.117 0.106 0.083 0.077 0.064 0.044 0.034 0.134 0.120 0.091 0.084 0.069 0.046 0.035 0.028 0.020 0.081 0.052 0.038 0.030 0.021 0.016 0.013 0.058 0.041 0.032 0.022 0.017 0.014 0.010 0.008
-0.196 0.171 0.124 0.114 0.140 0.127 0.099 0.092 0.077 0.053 0.040
--
0.109 0.101 0.083 0.056 0.042 0.034 0.024 0.098 0.062 0.045 0.036 0.025 0.019 0.016 0.070 0.050 0.038 0.026 0.020 0.016 0.012 0.009
-0.228 0.199 0.145 0.133 0.164 0.148 0.116 0.108 0.090 0.062 0.047
--
0.127 0.118 0.096 0.065 0.049 0.039 0.028 0.114 0.072 0.053 0.042 0.029 0.023 0.018 0.082 0.058 0.045 0.031 0.023 0.019 0.014 0.011
-0.261 0.228 0.165 0.152 0.187 0.169 0.132 0.123 0.102 0.070 0.054
--
0.146 0.135 0.110 0.074 0.056 0.045 0.032 0.130 0.083 0.061 0.048 0.034 0.026 0.021 0.093 0.066 0.051 0.035 0.027 0.022 0.016 0.012
--------------
0.182 0.169 0.138 0.093 0.070 0.056 0.040 0.163 0.103 0.076 0.060 0.042 0.032 0.026 0.117 0.083 0.064 0.044 0.034 0.027 0.020 0.015
--------------
0.219 0.203 0.165 0.111 0.084 0.067 0.048 0.196 0.124 0.091 0.072 0.050 0.039 0.032 0.140 0.099 0.077 0.053 0.040 0.033 0.024 0.018
---------------------
0.261 0.165 0.121 0.096 0.067 0.052 0.042 0.187 0.132 0.102 0.070 0.054 0.043 0.031 0.025
----------------------------
0.234 0.165 0.128 0.088 0.067 0.054 0.039 0.031
0.076 0.065 0.057 0.041 0.038 0.047 0.042 0.033 0.031 0.026 0.018 0.013 0.054 0.048 0.036 0.034 0.028 0.019 0.014 0.011 0.008 0.033 0.021 0.015 0.012 0.008 0.006 0.005 0.023 0.017 0.013 0.009 0.007 0.005 0.004 0.003
Section Insert size(d)
ØDHmin
ØdTool Dia.(ØD)
ØD(inch) ØD(mm)Ramping angleα°(max)
Ramping angle (α°) by ap
ap=0.079 ap=0.098 ap=0.118 ap=0.138 ap=0.157 ap=0.197 ap=0.236 ap=0.315 ap=0.394ap=0.039
ØDHmin ØDHmaxap
ap
RPCT-MA
RPMT-MF
RPMT-MM
RPMW
Insert size(d): Please refer page 4, applicable insert drawing.
(inch)
• ØD = Tool Dia.(inch)• Ød(Tool Path, inch) = ØDHmin, max - ØD• ØDHmin(Minimum hole diameter) = ØD × 2 - Insert size(d)• ØDHmax(Maximum hole diameter) = ØD×2 - 2
• ap = Depth of cut
• Ramping angle by ap(α°) = tan-1 Helical angle adjusted by ap cannot exceed maximum angle
( )ap
π × Ød
FMR P-positive _07
FMR2500
FMR3000
FMR4000
FMR5000
FMR6000
0.315 0.315 0.315 0.315 0.315 0.394 0.394 0.394 0.394 0.394 0.394 0.394 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.630 0.630 0.630 0.630 0.630 0.630 0.630 0.787 0.787 0.787 0.787 0.787 0.787 0.787 0.787
0.688 0.750 0.813 1.000 1.063 1.000 1.063 1.250 1.313 1.500 2.000 2.500 1.000 1.063 1.250 1.313 1.500 2.000 2.500 3.000 4.000 1.500 2.000 2.500 3.000 4.000 5.000 6.000 2.000 2.500 3.000 4.000 5.000 6.000 8.000
10.000
17.463 19.050 20.638 25.400 26.988 25.400 26.988 31.750 33.338 38.100 50.800 63.500 25.400 26.988 31.750 33.338 38.100 50.800 63.500 76.200
101.600 38.100 50.800 63.500 76.200
101.600 127.000 152.400 50.800 63.500 76.200
101.600 127.000 152.400 203.200 254.000
4.44 17.30 14.40 9.54 8.57
13.30 11.67 8.52 7.82 6.26 4.09 3.03 4.34 3.76
14.94 13.49 10.44 6.49 4.71 3.69 2.58
20.01 10.99 7.54 5.73 3.87 2.92 2.35
17.22 10.99 8.04 5.23 3.87 3.07 2.18 1.68
1.30 1.42 1.55 1.92 2.05 1.92 2.05 2.42 2.55 2.92 3.92 4.92 1.92 2.05 2.42 2.55 2.92 3.92 4.92 5.92 7.92 2.92 3.92 4.92 5.92 7.92 9.92
11.92 3.92 4.92 5.92 7.92 9.92
11.92 15.92 19.92
0.61 0.67 0.73 0.92 0.98 0.92 0.98 1.17 1.23 1.42 1.92 2.42 0.92 0.98 1.17 1.23 1.42 1.92 2.42 2.92 3.92 1.42 1.92 2.42 2.92 3.92 4.92 5.92 1.92 2.42 2.92 3.92 4.92 5.92 7.92 9.92
0.093 0.084 0.077 0.061 0.058 0.061 0.058 0.048 0.046 0.040 0.029 0.023 0.061 0.058 0.048 0.046 0.040 0.029 0.023 0.019 0.014 0.040 0.029 0.023 0.019 0.014 0.011 0.010 0.029 0.023 0.019 0.014 0.011 0.010 0.007 0.006
0.116 0.105 0.096 0.077 0.072 0.077 0.072 0.060 0.057 0.050 0.037 0.029 0.077 0.072 0.060 0.057 0.050 0.037 0.029 0.024 0.018 0.050 0.037 0.029 0.024 0.018 0.014 0.012 0.037 0.029 0.024 0.018 0.014 0.012 0.009 0.007
0.140 0.127 0.116 0.092 0.086 0.092 0.086 0.072 0.069 0.060 0.044 0.035 0.092 0.086 0.072 0.069 0.060 0.044 0.035 0.029 0.022 0.060 0.044 0.035 0.029 0.022 0.017 0.014 0.044 0.035 0.029 0.022 0.017 0.014 0.011 0.009
-0.148 0.135 0.108 0.101 0.108 0.101 0.085 0.080 0.070 0.052 0.041 0.108 0.101 0.085 0.080 0.070 0.052 0.041 0.034 0.025 0.070 0.052 0.041 0.034 0.025 0.020 0.017 0.052 0.041 0.034 0.025 0.020 0.017 0.012 0.010
-0.169 0.154 0.123 0.115 0.123 0.115 0.097 0.092 0.080 0.059 0.047 0.123 0.115 0.097 0.092 0.080 0.059 0.047 0.039 0.029 0.080 0.059 0.047 0.039 0.029 0.023 0.019 0.059 0.047 0.039 0.029 0.023 0.019 0.014 0.011
--------------
0.121 0.115 0.100 0.074 0.058 0.048 0.036 0.100 0.074 0.058 0.048 0.036 0.029 0.024 0.074 0.058 0.048 0.036 0.029 0.024 0.018 0.014
--------------
0.145 0.138 0.120 0.088 0.070 0.058 0.043 0.120 0.088 0.070 0.058 0.043 0.034 0.029 0.088 0.070 0.058 0.043 0.034 0.029 0.021 0.017
---------------------
0.159 0.118 0.094 0.077 0.058 0.046 0.038 0.118 0.094 0.077 0.058 0.046 0.038 0.029 0.023
----------------------------
0.147 0.117 0.097 0.072 0.057 0.048 0.036 0.029
0.046 0.042 0.039 0.031 0.029 0.031 0.029 0.024 0.023 0.020 0.015 0.012 0.031 0.029 0.024 0.023 0.020 0.015 0.012 0.010 0.007 0.020 0.015 0.012 0.010 0.007 0.006 0.005 0.015 0.012 0.010 0.007 0.006 0.005 0.004 0.003
Section Insert size(d)
ØDHmax
ØdTool Dia.(ØD)
ØD(inch) ØD(mm)Ramping angleα°(max)
Ramping angle (α°) by ap
ap=0.079 ap=0.098 ap=0.118 ap=0.138 ap=0.157 ap=0.197 ap=0.236 ap=0.315 ap=0.394ap=0.039
Insert size(d): Please refer page 4, applicable insert drawing.
(inch)
• ØD = Tool Dia.(inch)• Ød(Tool Path, inch) = ØDHmin, max - ØD• ØDHmin(Minimum hole diameter) = ØD × 2 - Insert size(d)• ØDHmax(Maximum hole diameter) = ØD×2 - 2
• ap = Depth of cut
Maximum hole diameter table for Helical machining(ØDHmax)ØDHmin ØDHmax
ap
ap
RPCT-MA
RPMT-MF
RPMT-MM
RPMW
• Ramping angle by ap(α°) = tan-1 Helical angle adjusted by ap cannot exceed maximum angle
( )ap
π × Ød
Quality, Performance, Value - Guaranteed!
FMR P-positiveFMRSA2500(Shank)
Fig. 1(inch)
25068HRP-2S06225068HRP-2M06225068HRP-2L06225075HRP-3S07525075HRP-3M07525075HRP-3L07525081HRP-3S07525081HRP-3M07525081HRP-3L07525100HRP-4S10025100HRP-4M10025100HRP-4L10025106HRP-4S10025106HRP-4L100
0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16
3.543 5.906 7.874 5.118 7.087 9.843 5.118 7.087 9.843 5.906 7.087 9.843 5.906 9.843
1.378 1.378 1.378 1.378 3.937 5.118 1.378 1.378 1.378 1.3782.3625.1181.3785.118
0.625 0.625 0.625 0.750 0.750 0.750 0.750 0.750 0.750 1.000 1.000 1.000 1.000 1.000
17.463 17.463 17.463 19.050 19.050 19.050 20.638 20.638 20.638 25.400 25.400 25.400 26.988 26.988
0.688 0.688 0.688 0.750 0.750 0.750 0.813 0.813 0.813 1.000 1.000 1.000 1.063 1.063
22233333344444
11111111111111
0.24 0.44 0.60 0.60 0.79 1.10 0.62 0.88 1.21 1.06 1.32 1.79 1.06 1.87
0.3150.3150.3150.3150.3150.3150.3150.3150.3150.3150.3150.3150.3150.315
Designation apLℓØdØD(mm)ØD(inch) Fig.lbs Insert size
FMRSA2500
Parts
Type
FTNA0305FTNA0306 TW09S - Ø0.6875
Ø0.75~Ø1.06252500 type
WrenchWrenchScrew Cutter Dia.
Type Designation UsageUncoatedCoated
H01PC5300PC3600 PC5400
: Stock item
Available Inserts
2500 type
RPMT0803M0E-MFRPMT0803M0S-MMRPMW0803M0E1
for Low cutting resistance machiningwith Stronger cutting edge
for High hardness material machining
RPMT-MMRPMT-MF RPMW
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
• AR : -4°• RR : -4°~-1°
08_ KORLOY TECH-NEWS
●●●---
●●●-
●●●-
----
FMR P-positive _09
FMRSA3000(Shank)
Fig. 1 Fig. 2(inch)
3100HRP-2M0753100HRP-2S1003100HRP-2M1003100HRP-2L1003106HRP-2L1003125HRP-3S1253125HRP-3L1253125HRP-4S1253125HRP-4L1003131HRP-4S1253131HRP-4M1253131HRP-4L125
0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20
6.693 4.724 6.299 9.843 7.874 4.921 7.874 4.921 7.874 4.921 7.087
11.811
1.575 1.575 2.362 5.118 1.181 1.575 2.362 1.575 2.362 1.575 2.362 7.087
0.750 1.000 1.000 1.000 1.000 1.250 1.250 1.250 1.250 1.250 1.250 1.250
25.400 25.400 25.400 25.400 26.988 31.750 31.750 31.750 31.750 33.338 33.338 33.338
1.000 1.000 1.000 1.000 1.063 1.250 1.250 1.250 1.250 1.313 1.313 1.313
222223344444
212221212122
0.88 0.86 1.15 1.76 1.52 1.50 2.38 1.46 1.63 1.48 2.21 3.62
0.3940.3940.3940.3940.3940.3940.3940.3940.3940.3940.3940.394
Designation apLℓØdØD(mm)ØD(inch) Fig.lbs Insert size
FMRSA3000
Parts
Type
FTGA03507FTGA03508 TW15S - Ø1.0~Ø1.0625
Ø1.25~Ø1.31253000 type
WrenchWrenchScrew Cutter Dia.
Type Designation UsageUncoatedCoated
H01PC5300PC3600 PC5400
: Stock item
Available Inserts
3000 type
RPCT10T3M0-MARPMT10T3M0E-MFRPMT10T3M0S-MMRPMW10T3M0E1
for Aℓ machiningfor Low cutting resistance machining
with Stronger cutting edgefor High hardness material machining
RPCT-MA RPMT-MMRPMT-MF RPMW
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
• AR : -4°• RR : -1°
-●●●
-●●●
-●●●
●---
Quality, Performance, Value - Guaranteed!
FMR P-positive
10_ KORLOY TECH-NEWS
FMRSA4000(Shank)
Fig. 1 Fig. 2(inch)
• AR : -4°• RR : -2°~0°
4100HRP-2S1004106HRP-2L1004125HRP-2L1004125HRP-2S1254125HRP-2L1254125HRP-3S1254125HRP-3M1254131HRP-3M1254131HRP-3L1254150HRP-3S1254150HRP-3M1254150HRP-4S1254150HRP-4M1254150HRP-4L1254200HRP-4M1254200HRP-4M150
0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24
6.299 7.874 7.480 4.921 9.843 4.921 6.299 7.874
11.811 4.134 6.299 4.134 5.906 9.843 5.906 5.906
2.362 2.362 1.575 1.969 1.969 1.969 2.362 2.362 2.362 1.378 1.969 1.378 1.378 1.378 1.969 1.969
1.000 1.000 1.000 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.500
25.400 26.988 31.750 31.750 31.750 31.750 31.750 33.338 33.338 38.100 38.100 38.100 38.100 38.100 50.800 50.800
1.000 1.063 1.250 1.250 1.250 1.250 1.250 1.313 1.313 1.500 1.500 1.500 1.500 1.500 2.000 2.000
2222233333344444
1221212221212222
1.01 1.06 1.50 1.41 3.09 1.41 1.87 2.23 3.68 1.32 2.12 1.32 1.92 3.22 2.43 3.18
0.4720.4720.4720.4720.4720.4720.4720.4720.4720.4720.4720.4720.4720.4720.4720.472
Designation apLℓØdØD(mm)ØD(inch) Fig.lbs Insert size
FMRSA4000
Type Designation UsageUncoatedCoated
H01PC5300PC3600 PC5400
: Stock item
Available Inserts
4000 type
RPCT1204M0-MARPET1204M0E-MLRPMT1204M0E-MFRPMT1204M0S-MMRPMW1204M0S1RPMW1204M0S2
for Aℓ machiningfor Titanium machning
for Low cutting resistance machiningwith Stronger cutting edge
for High hardness material machiningfor High hardness material machining(with Stronger cutting edge)
Parts
Type
FTKA0408FTKA0410 TW15S - Ø1.0~Ø1.0625
Ø1.25~Ø2.04000 type
WrenchWrenchScrew Cutter Dia.
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
RPCT-MA RPMT-MMRPMT-MF RPMWRPET-ML
--●●--
●-----
--●●●●
--●●●●
FMR P-positive _11
FMRSA5000/6000(Shank)
Fig. 1 Fig. 2(inch)
• AR : -4°• RR : 0°
5150HRP-2M1255150HRP-2L1255200HRP-3M1505200HRP-3L1506200HRP-3S1256200HRP-3M1256200HRP-3S1506200HRP-3M150
0.31 0.31 0.31 0.31 0.39 0.39 0.39 0.39
6.299 9.843 6.299
11.811 6.299 7.874 4.921 7.874
1.969 1.969 1.969 1.969 1.969 1.969 1.969 1.969
1.250 1.250 1.500 1.500 1.250 1.250 1.500 1.500
38.100 38.100 50.800 50.80050.80050.80050.80050.800
1.500 1.500 2.000 2.000 2.0002.0002.0002.000
22333333
22221212
2.03 3.20 3.26 6.31 2.34 2.87 3.20 4.08
0.6300.6300.6300.6300.7870.7870.7870.787
Designation apLℓØdØD(mm)ØD(inch) Fig.lbs Insert size
FMRSA5000
FMRSA6000
Type Designation UsageUncoatedCoated
H01PC3600 PC5300 PC5400
: Stock item
Available Inserts
5000 type
6000 type
RPCT1606M0-MARPMT1606M0E-MFRPMT1606M0S-MMRPMW1606M0S1RPCT2007M0-MARPET2007M0-MLRPMT2007M0E-MFRPMT2007M0S-MMRPMW2007M0S1
for Aℓ machiningfor low cutting resistance machining
with Stronger cutting edgefor High hardness material machining
for Aℓ machiningfor Titanium machning
for Low cutting resistance machiningwith Stronger cutting edge
for High hardness material machining
Parts
Type
FTGA0511-PFTKA0615-P
--
TW20-100TW25-100
Ø1.5~Ø2.0Ø2.0
5000 type6000 type
WrenchWrenchScrew Cutter Dia.
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
RPCT-MA RPMT-MMRPMT-MF RPMWRPET-ML
- -
-●●---●●--
-●●●--●●●-
-●●●--●●●-
●---●-----
Quality, Performance, Value - Guaranteed!
FMR P-positive
12_ KORLOY TECH-NEWS
FMRCA3000(Cutter)
20
14
26
18
• AR : 5°• RR : -4°~0°
3150HRP-5
3200HRP-6
3250HRP-6
3250HRP-7
0.20
0.20
0.20
0.20
0.500
0.750
1.000
1.000
0.287
0.413
0.551
0.551
0.433
0.630
0.827
0.827
0.252
0.315
0.374
0.374
0.169
0.220
0.248
0.248
0.630
0.787
0.787
0.787
1.500
1.750
1.750
1.750
1.417
1.772
2.205
2.205
38.100
50.800
63.500
63.500
1.500
2.000
2.500
2.500
5
6
6
7
0.49
0.77
1.21
1.23
0.394
0.394
0.394
0.394
Designation apØd Ød1 Ød2 a b E FØD2ØD(mm)ØD(inch) lbs Insert size
FMRCA3000
(inch)
Type Designation UsageUncoatedCoated
H01PC5300PC3600 PC5400
: Stock item
Available Inserts
3000 type
RPCT10T3M0-MARPMT10T3M0E-MFRPMT10T3M0S-MMRPMW10T3M0E1
for Aℓ machiningfor Low cutting resistance machining
with Stronger cutting edgefor High hardness material machining
Parts
Type
FTGA03508 TW15S - Ø1.5~Ø2.53000 type
WrenchWrenchScrew Cutter Dia.
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
RPCT-MA RPMT-MMRPMT-MF RPMWRPET-ML-
-●●-
-●●●
-●●●
●---
FMR P-positive _13
FMRCA4000(Cutter) • AR : 5°• RR : -2°
4200HRP-4
4200HRP-5
4250HRP-5
4250HRP-6
4300HRP-6
4300HRP-7
4400HRP-7
0.24
0.24
0.24
0.24
0.24
0.24
0.24
0.750
0.750
1.000
1.000
1.000
1.000
1.250
0.413
0.413
0.551
0.551
0.551
0.551
0.689
0.630
0.630
0.827
0.827
0.866
0.866
1.024
-
-
-
-
1.299
1.299
1.614
0.315
0.315
0.374
0.374
0.374
0.374
0.500
0.220
0.220
0.248
0.248
0.248
0.248
0.319
0.787
0.787
0.787
0.787
0.787
0.787
0.787
1.750
1.750
1.750
1.750
2.000
2.000
2.000
1.772
1.772
2.205
2.205
2.205
2.205
2.874
50.800
50.800
63.500
63.500
76.200
76.200
101.600
2.000
2.000
2.500
2.500
3.000
3.000
4.000
4
5
5
6
6
7
7
0.57
0.62
0.97
1.06
2.03
1.98
3.22
0.472
0.472
0.472
0.472
0.472
0.472
0.472
Designation apØd Ød1 Ød2 Ød3 a b E FØD2ØD(mm)ØD(inch) lbs Insert size
FMRCA4000
(inch)
Type Designation UsageUncoatedCoated
H01PC3600 PC5300 PC5400
: Stock item
Available Inserts
4000 type
RPCT1204M0-MARPET1204M0-MLRPMT1204M0E-MFRPMT1204M0S-MMRPMW1204M0S1RPMW1204M0S2
for Aℓ machiningfor Titanium machning
for Low cutting resistance machiningwith Stronger cutting edge
for High hardness material machiningfor High hardness material machining(with Stronger cutting edge)
Parts
Type
FTKA0410 TW15S - Ø2.0~Ø4.04000 type
WrenchWrenchScrew Cutter Dia.
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
20
14
26
18
28
RPCT-MA RPMT-MMRPMT-MF RPMWRPET-ML
--●●---
--●●●●-
--●●●●-
●------- -
Quality, Performance, Value - Guaranteed!
FMR P-positive
14_ KORLOY TECH-NEWS
FMRCA5000(Cutter) • AR : 5°• RR : -1°~0°
5250HRP-4
5250HRP-5
5300HRP-5
5300HRP-6
5400HRP-6
5500HRP-7
5500HRP-8
5600RP-8
0.31
0.31
0.31
0.31
0.31
0.31
0.31
0.31
1.000
1.000
1.000
1.000
1.250
1.500
1.500
2.000
0.551
0.551
0.551
0.551
0.689
0.827
0.827
-
0.827
0.827
0.866
0.866
1.024
1.220
1.220
-
-
-
1.299
1.299
1.614
1.969
1.969
-
0.374
0.374
0.374
0.374
0.500
0.626
0.626
0.752
0.248
0.248
0.248
0.248
0.319
0.394
0.394
0.433
0.787
0.787
0.787
0.787
0.787
1.063
1.063
1.181
1.750
1.750
2.000
2.000
2.000
2.500
2.500
2.500
2.205
2.205
2.205
2.205
2.874
3.386
3.386
4.882
63.500
63.500
76.200
76.200
101.600
127.000
127.000
152.400
2.500
2.500
3.000
3.000
4.000
5.000
5.000
6.000
4
5
5
6
6
7
8
8
1
1
1
1
1
1
1
2
0.95
0.97
1.70
1.81
3.13
6.13
6.15
8.84
0.630
0.630
0.630
0.630
0.630
0.630
0.630
0.630
Designation apØd Ød1 Ød2 Ød3 a b E FØD2ØD(mm)ØD(inch) Fig.lbs Insert size
FMRCA5000
(inch)
Type Designation UsageUncoatedCoated
H01PC3600 PC5300 PC5400
: Stock item
Available Inserts
5000 type
RPCT1606M0-MARPMT1606M0E-MFRPMT1606M0S-MMRPMW1606M0S1
for Aℓ machiningfor Low cutting resistance machining
with Stronger cutting edgefor High hardness material machining
Parts
Type
FTGA0512-P - TW20-100 Ø2.5~Ø6.05000 type
WrenchWrenchScrew Cutter Dia.
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
Fig.1 Fig.2
20
14
26
18
28
20
14
26
18
28
RPCT-MA RPMT-MMRPMT-MF RPMWRPET-ML
-●●-
-●●●
-●●●
●---
FMR P-positive _15
FMRCA6000(Cutter) • AR : 5°• RR : 0°
6250HRP-4
6300HRP-5
6400HRP-5
6400HRP-6
6500HRP-5
6500HRP-7
6600RP-6
6600RP-8
6800RP-8
61000RP-9
0.39
0.39
0.39
0.39
0.39
0.39
0.39
0.39
0.39
0.39
1.000
1.000
1.250
1.250
1.500
1.500
2.000
2.000
2.500
2.500
0.551
0.551
0.689
0.689
0.827
0.827
-
-
-
-
0.787
0.827
1.024
1.024
1.220
1.220
-
-
-
-
-
-
1.614
1.614
1.969
1.969
-
-
-
-
0.374
0.374
0.500
0.500
0.626
0.626
0.752
0.752
1.000
1.000
0.248
0.248
0.319
0.319
0.394
0.394
0.433
0.433
0.551
0.551
0.787
0.866
0.787
0.787
1.063
1.063
1.181
1.181
1.496
1.496
1.750
2.000
2.000
2.000
2.500
2.500
2.500
2.500
2.500
2.500
2.205
2.205
2.874
2.874
3.386
3.386
4.882
4.882
5.118
7.087
63.500
76.200
101.600
101.600
127.000
127.000
152.400
152.400
203.200
254.000
2.500
3.000
4.000
4.000
5.000
5.000
6.000
6.000
8.000
10.000
4
5
5
6
5
7
6
8
8
9
1
1
1
1
1
1
2
2
3
3
0.82
1.92
2.89
3.09
6.11
6.37
7.89
7.78
11.36
21.43
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
Designation apØd Ød1 Ød2 Ød3 a b E FØD2ØD(mm)ØD(inch) Fig.lbs Insert size
FMRCA6000
(inch)
Type Designation UsageUncoatedCoated
H01PC3600 PC5300 PC5400
: Stock item
Available Inserts
6000 type
RPCT2007M0-MARPET2007M0-MLRPMT2007M0E-MFRPMT2007M0S-MMRPMW2007M0S1
for Aℓ machiningfor Titanium machning
for Low cutting resistance machiningwith Stronger cutting edge
for High hardness material machining
Parts
Type
FTKA0615-P - TW25-100 Ø2.5~Ø10.06000 type
WrenchWrenchScrew Cutter Dia.
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
Fig.1 Fig.2 Fig.3
20
14
26
18
28
20
14
26
18
28
20
14
26
18
28
RPCT-MA RPMT-MMRPMT-MF RPMWRPET-ML
--●●-
--●●●
--●●●
●----
Quality, Performance, Value - Guaranteed!
FMR P-positive
16_ KORLOY TECH-NEWS
FMRMA2500/3000(Modular) • AR : -4°• RR : -4°~0°
(inch)
25068HRP-M0825075HRP-M1025100HRP-M1225125HRP-M1625150HRP-M163100HRP-M123125HRP-M163150HRP-M16
0.16 0.16 0.16 0.16 0.16 0.20 0.20 0.20
0.3150.3150.3150.3150.3150.3940.3940.394
M08M10M12M16M16M12M16M16
1.654 2.008 2.323 2.638 2.638 2.323 2.638 2.638
0.984 1.181 1.378 1.575 1.575 1.378 1.575 1.575
0.571 0.709 0.906 1.142 1.142 0.906 1.142 1.142
0.335 0.413 0.492 0.669 0.669 0.492 0.669 0.669
17.463 19.050 25.400 31.750 38.100 25.400 31.750 38.100
0.688 0.750 1.000 1.250 1.500 1.000 1.250 1.500
23445233
0.07 0.13 0.24 0.49 0.57 0.22 0.44 0.55
Designation ap Insert sizeMLℓØd Ød1ØD(mm)ØD(inch) lbs
FMRMA2500
FMRMA3000
Type Designation UsageUncoatedCoated
H01PC3600 PC5300 PC5400
: Stock item
Available Inserts
2500 type
3000 type
RPMT0803M0E-MFRPMT0803M0S-MMRPMW0803M0E1RPCT10T3M0-MARPMT10T3M0E-MFRPMT10T3M0S-MMRPMW10T3M0E1
for Low cutting resistance machiningwith Stronger cutting edge
for High hardness material machiningfor Aℓ machining
for Low cutting resistance machiningwith Stronger cutting edge
for High hardness material machining
Parts
Type
FTNA0305FTNA0306
FTGA03507FTGA03508
TW09S
TW15S
-
-
Ø0.6875~Ø0.75Ø1.0~Ø1.5
Ø1.0Ø1.25~Ø1.5
2500 type
3000 type
WrenchWrenchScrew Cutter Dia.
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
RPCT-MA RPMT-MMRPMT-MF RPMWRPET-ML
●●--●●-
●●●-●●●
●●●-●●●
---●---
FMR P-positive _17
FMRMA4000/5000(Modular) • AR : -4°• RR : 0°
(inch)
4100HRP-M124125HRP-M164150HRP-M165150HRP-M16
0.24 0.24 0.24 0.31
M12M16M16M16
2.323 2.638 2.638 2.638
1.378 1.575 1.575 1.575
0.906 1.142 1.142 1.142
0.492 0.669 0.669 0.669
25.400 31.750 38.100 38.100
1.000 1.250 1.500 1.500
2342
0.22 0.46 0.53 0.46
0.4720.4720.4720.630
Designation apMLℓØd Ød1ØD(mm)ØD(inch) lbs Insert size
FMRMA4000
FMRMA5000
Type Designation UsageUncoatedCoated
H01PC3600 PC5300 PC5400
: Stock item
Available Inserts
4000 type
5000 type
RPCT1204M0-MARPET1204M0-MLRPMT1204M0E-MFRPMT1204M0S-MMRPMW1204M0S1RPMW1204M0S2RPCT1606M0-MARPMT1606M0E-MFRPMT1606M0S-MMRPMW1606M0S1
for Aℓ machiningfor Titanium machning
for Low cutting resistance machiningwith Stronger cutting edge
for High hardness material machiningfor High hardness material machining(With stronger cutting edge)
for Aℓ machiningfor Low cutting resistance machining
with Stronger cutting edgefor High hardness material machining
Parts
Type
FTKA0408FTKA0410
FTGA0511-P
TW15S
-
-
TW20-100
Ø1.0Ø1.25~Ø1.5
Ø1.5
4000 type
5000 type
WrenchWrenchScrew Cutter Dia.
Recommended condition for work piece, grade: Please refer to bottom of page2.Insert size(d): Please refer page 4, applicable insert drawing.
RPCT-MA RPMT-MMRPMT-MF RPMWRPET-ML
--●●---●●-
--●●●●-●●●
--●●●●-●●●
●-----●---
Head OfficeHolystar B/D, 1350, Nambusunhwan-ro, Geumcheon-gu, Seoul, 153-823, KoreaTel : +82-2-522-3181 Fax : +82-2-522-3184, +82-2-3474-4744Web : www.korloy.com E-mail : export@korloy.com
Cheongju Factory55, Sandan-ro, Heungdeok-gu, Cheongju-si,Chungcheongbuk-do, 361-290, KoreaTel : +82-43-262-0141 Fax : +82-43-262-0146
Jincheon Factory54, Gwanghyewonsandan 2-gil, Gwanghyewon-myeon, Jincheon-gun,Chungcheongbuk-do, 365-831, KoreaTel : +82-43-535-0141 Fax : +82-43-535-0144
R & D Institute55, Sandan-ro, Heungdeok-gu, Cheongju-si,Chungcheongbuk-do, 361-290, KoreaTel : +82-43-262-0141 Fax : +82-43-262-0711
Heinrich-Lanz-Allee 12, 60437 Frankfurt am Main, GermanyTel : +49-69-5069-887-0 Fax : +49-69-5069-887-29www.korloyeurope.com E-mail : sales@korloyeurope.com
Plot NO.415, Sector 8, IMT Manesar, Gurgaon 122051, Haryana, INDIATel : +91-124-4391790 Fax : +91-124-4050032www.korloyindia.com E-mail : sales.kip@korloy.com
Av. Aruana 280, conj.12, WLC, Alphaville, Barueri, CEP06460-010, SP, BrasilTel : +55-11-4193-3810E-mail : vendas@korloy.com
Ground Dongjing Road 56 District Free Trade Zone. Qingdao, ChinaTel : +86-532-86959880 Fax : +86-532-86760651E-mail : kycpjh@korloy.com
KORLOY Engineering Center Cheongju Research & Development
Jincheon Factory Office Jincheon FactoryHead Office
20151230
TN12-EI-01
620 Maple Avenue, Torrance, CA 90503, USATel : +1-310-782-3800 Toll Free : +1-888-711-0001 Fax : +1-310-782-3885 E-mail : sales@korloy.uswww.korloyamerica.com
KORLOYHead Office
KORLOY America
KORLOY Brasil
KORLOY China (DINE)KORLOY Factory (Qingdao)
KORLOY India
KORLOY Europe
PDF Only
top related