experimental work chp 7
Post on 01-Jun-2018
218 Views
Preview:
TRANSCRIPT
-
8/9/2019 Experimental Work CHP 7
1/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Chapter - 7
EXPERIMENTAL PROGRAM
The experimental study was carried out at the Construction Material Testing Laboratory, Facultyof Civil Engineering, Mirpur University of cience !nd Technology Mirpur !"#$
Fig 6.1
Construction Material Testing Laboratory
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page120
-
8/9/2019 Experimental Work CHP 7
2/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
7.1 Materials:
The materials used in this investigation are given below$ The same type of materials wereused throughout the pro%ect but unavoidably they were from different &uerries$
There are many widely accepted methods of sampling and testing of concrete and steel$ The
properties of the concrete and steel used were determined by standard tests according to the
!TM$ The designof the concrete mixes used in the pro%ect and the properties of the various
materials used are presented in this chapter
7.1.1 Coarse Aggregates:
Margalla Crush was used$ 'e ta(e 1” down crush material from crusher )T!*+L!$
-esides grading, the si.e of aggregates is also important in the sense that it affects the
wor(ability and strength of concrete mix$ The larger the maximum si.e of the aggregate, the
smaller is the cement re&uirement for a particular water to cement ratio$ This reduces the heat of
hydration and results in lesser thermal and shrin(age crac(s$ /owever, in structural wor(s, the
maximum si.e of aggregates in concrete is usually restricted to 01 mm or 23$1 mm )4 in$ or 4$1
in$ due to the limited si.e of concrete sections and spacing of reinforcing bars$
Figure5 3$0 Margalla
crush plant taxila
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page121
-
8/9/2019 Experimental Work CHP 7
3/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
7.1.1.1
Quartering:
The &uartering procedure is as follows5
1) 6lace the sample on a hard, clean, level, non7absorptive surface where there will be
no000 loss of material nor the accidental addition of foreign material$
2) Using a large trowel, shovel, or other suitable tool turn the entire sample over at least
three times$ Form the sample into a conical pile by depositing individual lifts on top of the
preceding lift$
3) Flatten the pile to a uniform thic(ness by pressing down the apex with a shovel or trowel$
Each &uarter sector of the resulting pile is re&uired to contain the material originally in the pile$
The diameter of the pile should be e&ual to 879 times the thic(ness of the pile$
4) 'ith a large trowel or other suitable tool, divide the sample into four e&ual &uarters$
:emove two diagonally opposite &uarters, including all fine material, and brush the cleared
spaces clean$
5) Combine diagonally opposite &uarters of the material into two samples$ !ll fine materials
shall be included by brushing the surface clean$ tore one of these two halves$ +f the remainingmaterial still weighs too much, repeat the entire &uartering process until the proper test sample
si.e is obtained$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page122
-
8/9/2019 Experimental Work CHP 7
4/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure: 6.3;uartering of aggregates
7.1.2 FIN A!!"!A#$
%a&ran'e(ur sand was used$ -ecause finess modulus of this sand is almost < 0$1 $The
fineness modulus is considered as a weighted average si.e of a sieve on which the material is
retained$ The fineness modulus gives an indication of the probable behavior of a concrete mix
made with aggregate having a certain grading$ ! larger value of fineness modulus indicates a
coarser particle whereas a smaller value indicates a finer particle$ Mathematically, the fineness
modulus is obtained by dividing the sum of cumulative percent mass retained at each sieve)designated in !TM C42=7>1 in a sieve analysis test, by 4>>$
7.1.3 Ceent:
?rdinary 6ortland cement with
the trade name Fau%i Cement was
used$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page123
-
8/9/2019 Experimental Work CHP 7
5/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure 7.5
Fau%i Cement
7.1.4 *ater re+u'ing Agent:
The water reducing agent used in this pro%ect was
manufactured and supplied by imporient chemicals@6ATB LT under the code name of Cherite A! ,
2--$ Chemrite !D70>> is a highly effective li&uid
super7plastici.er for production of free flowing
concrete, which prolongs slump retention at low
water7cement ratios$
Figure: 7.6'ater :educing !gent
7.1.5 $teel ars:
eformed steel !ra+e 4- for /0and /3 bars were used in the test beams$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page124
-
8/9/2019 Experimental Work CHP 7
6/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure 7.7teel bars
6.1.7 Ferrocement
T! "e##!$e%e&' %e()e( *#e$'a&g+,a# a&-
)e.ag!&a, / e#e +(e-!') ')e(e %e()e( e#e
#ae- !&e !& a&!')e# *)e.ag!&a, %e()
#ae- !& #e$'a&g+,a#/ (! ')a' ')e !&- ,,
g!!- ') ')e $!&$#e'e
Fi
6.! Rectan"#ar an$ he%aona#&errocement
7.1.0 For&or:
$teel formwor( )molds was
used for casting beams
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page12
-
8/9/2019 Experimental Work CHP 7
7/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure 7.1-
teel Formwor(
7.3 Mi esign: 56
7.3.1 Intro+u'tion:
The !C+ method 044$4 is used to design normal and heavy weight concrete mixes having
twenty eight days compressive strength of 21M6a or 1>>> psi )maximum$
ound design or analysis of a composite structure depends on reliable information about the
properties of the materials to be used$ The strength of a reinforced concrete member and its
resistance to crac(ing and prevention of corrosion of reinforcement depend on many parameters, particularly on the strength properties of concrete and steel$ The deformations are related to the
stiffnesss of the members which in turn depend on the characteristics of their components
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page125
-
8/9/2019 Experimental Work CHP 7
8/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
7.3.2 a'groun+ ata:
To the extent possible, selection of concrete proportions should be based on test data or
experience with the materials actually to be used$ 'here such bac(ground is limited or not
available, estimates given in this recommended practice may be employed$
The following information for available materials will be useful5
• ieve analyses of fine and coarse aggregates$
• Unit weight of coarse aggregate$
• -ul( specific gravities and absorptions of aggregates$
• Mixing7water re&uirements of concrete developed from experience with available
aggregates$
• :elationships between strength and water7cement ratio or ratio of water7to7cement
plus other cementitious materials, for available combinations of cements, other
cementitious materials if considered, and aggregates$
• pecific gravities of portland cement and other cementitious materials, if used$
• ?ptimum combination of coarse aggregates to meet the maximum density grading for
mass concrete
7.3.3 #est:
ir8 $ie9e Anal8sis o Fine an+ Coarse Aggregates
;A$#M esignation: C l36)57
$'o(e < $ignii'an'e:
• This test method covers the determination of the particle si.e distribution of fine and
coarse aggregates by sieving$
• This gradation gives an indirect measure if the wor(ability and average particle si.e$
• !ccurate determination of materials finer than 31 micron )ieve o 0>> cannot be
achieved by this test
A((aratus
• tandard set of sieves
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page127
-
8/9/2019 Experimental Work CHP 7
9/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
• ieve sha(er
• ample of the aggregate
Figure: 7.11
ieve analysis
=ro'e+ure:
• Ta(e the oven7dried sample$ The sample should be perfectly dry because if there is some
moisture content present then the particles will stic( together and will not pass through
the sieves$
• Temperature of the oven G 44>H1 IC
• 6lace the set of standard and non7standard sieves one above another with the smallest
aperture opening at the bottom$
• The pan is placed at the bottom7most position$
• This experiment can be performed manually or with the aid of a machine called Jsieve
sha(erK$
• The manual method should be performed in a proper se&uence which is as follows
i$ forward and bac(ward motion
ii$ left and right motion
iii$ cloc(wise )C' and counter7cloc(wise )CC' motion
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page126
-
8/9/2019 Experimental Work CHP 7
10/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
iv$ Fre&uent %olting$• Time elapsed for the sieving process is 271 minutes and should not be less than 2 minutes
• 'eigh the mass retained on each sieve and calculate the percentage passing through each sieve$
• Then the FM can be calculated by using the relation
Finess modulus >
Cumulative retainedonstandardsievesof 150 µmorabove¿
Ʃ ¿
¿
!ra+ing "e?uireent or Coarse Aggregates
;Qualit8 o A$a(le):
Drading basically indicates the si.es of the aggregates and in which proportions they are present$
There are some limiting values for every sieve provided by !TM or -, we use these limiting
values to get our final answer$ Ta(e the minimum and the maximum values provided by !TM$
ow ta(e these minimum and maximum value as your reference and if the values of our own
data lies inside theseminimum and the maximum values provided by !TM, then the &uality of
our sample is ?# but if your values lies outside these of maximum and minimum range then the
sample is not according to specifications$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page12
-
8/9/2019 Experimental Work CHP 7
11/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
@ser9ation < Cal'ulation:
#ale , 7.1: :esults of Course aggregate )Margalla Crush
Total 'eight of ampleG 8>>>g
:EULT
Material G 4K down material
Max nominal si.e G 28K
Drading re&uirements for coarse aggregates G si.e =3 ?#N
FIN A!!"!A#$ ;%a&ran'e(ur san+)
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page130
$ie9e
sie
ass
retaine+
;g)
In+i9i+ual B
retaine+
Cuulati9e B
retaine+
Cuulati9e B
(assing
$ie 67
"e?uireent
s
1” > > > 4>> 4>>
34” 28= 9$=1 9$=1 O4$21 O>74>>
30” 098> 34 3O$=1 0>$21 0>711
/4 3O9 4O$O1 OO$= >$8 >74>
/0 8 >$4 OO$3 >$2 >71
=an 40 >$2 4>> >
#otal 8>>>
-
8/9/2019 Experimental Work CHP 7
12/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Total 'eight of ampleG 4>>>g
#ale , 7.2::esults of fine aggregate
$ie9e sie Mass retaine+;g)
In+i9i+ual Bretaine+
Cuulati9e Bretaine+
Cuulati9e B(assing
/4 49 4$3O 4$3O O9$04
/0 => 1$O= 3$31 O0$01
/16 4O> 49$93 0=$=0 32$29
/3- 20> 24$39 19$8> 84$=>
/5- 004 04$O1 9>$21 4O$=1
/1-- 491 49$23 O9$30 4$09
=an 42 4$0O 4>> >
#otal 4>>3
"esults:
Finess modulus >
Cumulative retainedonstandardsievesof ¿
100orabove
Ʃ¿
¿
> Ʃ(1.79+7.75+26.62+58.40+80.35+98.72)
100
G0$3 ?#N
iir8 ro++e+ Dnit &eight o 'oarse aggregate
;A$#M esignation: C 2E)50
$'o(e < $ignii'an'e:
• This test method is used to determine the dry rodded unit weight of the given coarse
grained specimen$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page131
-
8/9/2019 Experimental Work CHP 7
13/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
• uring the concrete mix design, when the aggregate is to be batched by volume or by
weight, then it becomes necessary to (now the mass of the aggregates that will fill the
container of unit volume$ +f we (now the bul( density of the aggregate material then we
can easily determine the mass re&uired to fill a unit volume container$• -ul( density also indicates the percentage of voids present in the aggregate material$ This
percentage of voids affects the grading of the aggregates which is important in high
strength concrete$
• -ul( density also indicates the compactive effort re&uired to compact the concrete$
A((aratus
• -alance
• Temping rod
• Measuring Cylinder-uc(et
• hovel or coop
Figure: 7.12
Measuring Cylinder-uc(et
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page132
-
8/9/2019 Experimental Work CHP 7
14/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
=ro'e+ure:
• Calibrate the metal buc(et to determine its volume by determining the net weight of
water re&uired to fill it and dividing it by the density of water$ For this test procedure it is
sufficiently accurate to accept the density of water at room temperature to be OO9 (gm 2
)=0$2 lbs$ ft2$
• :odding the aggregates$ Fill the buc(et one7third full and rod the aggregate layer with 01
stro(es of the tamping rod, evenly distributed over the surface$ !dd another layer of
aggregates so that the buc(et is approximately two7thirds full and repeat the rodding
procedure$ The third layer of aggregates should fill the pail to overflowing$ !gain repeat
the tamping procedure and stri(e off the excess with the tamping rod$ Manually try to
balance the depressions below the top of the buc(et with slight pro%ections above the top$
'hen tamping the first lift, do not permit the rod to penetrate to the bottom of the buc(et$
/owever, the subse&uent lifts should penetrate to the top of the previous lift$
• The rodded unit weight is computed in (gm2 )lbft2 from the net weight of the rodded
aggregates in the buc(et divided by its volume$
@ser9ation
-
8/9/2019 Experimental Work CHP 7
15/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
G( Weightofcylinder+Weightofaggregates)−(Weightofemptycylinder )
Volumeofcylinder
G
(29.80−7.4 )0.01374
G 4=2> (gm2
iii$(e'ii' gra9it8 an+ asor(tion o 'oarse aggregates
;A$#M esignation: C 127 )5E
$'o(e < $ignii'an'e:
• This method covers the determination of specific gravity and absorption of coarse
aggregate$ The specific gravity may be expressed as bul( specific gravity, bul( specific
gravity )saturated7 surface7dry ), or apparent specific gravity$ The bul( specific
gravity ) and absorption are based on aggregate after 41 hours soa(ing in water$ This
method is not intended to be used with lightweight aggregates$
• +t is used for the calculation of the volume occupied by the aggregates in various
mixtures
einitions:
;a) $(e'ii' gra9it8:
The ratio of the mass )or weight in air of a unit volume of a material to the mass of the
same volume of water at stated temperatures$ Aalues are dimensionless$
;)Asor(tion:
The increase in the mass of aggregate due to water in the pores of the material, but not including
water adhering to the outside surface of the particles, expressed as a percentage of the dry mass$
The aggregate is considered JdryK when it has been maintained at a temperature of 44> H 1QC for
sufficient time to remove all uncombined water$
;')A((arent s(e'ii' gra9it8:
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page134
-
8/9/2019 Experimental Work CHP 7
16/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
The ratio of the weight in air of a unit volume of the impermeable portion of aggregate at a stated
temperature to the weight in air of an e&ual volume of gas7free distilled water at a stated
temperature$
;+)ul s(e'ii' gra9it8 ;o9en +r8)
The ratio of the weight in air of a unit volume of aggregate )including the permeable and
impermeable voids in the particles, but not including the voids between particles at a stated
temperature to the weight in air of an e&ual volume of gas7free distilled water at a stated
temperature$
;e)ul s(e'ii' gra9it8 ;$$)
The ratio of the mass in air of a unit volume of aggregate, including the mass of water within the
voids filled to the extent achieved by submerging in water for approximately 41 hours )but not
including the voids between particles at a stated temperature, compared to the weight in air of
an e&ual volume of gas7free distilled water at a stated temperature$
A((aratus
• -alance
• ample Container
• 'ater Tan(
• uspended !pparatus
• ?ven
• ?ven
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page13
-
8/9/2019 Experimental Work CHP 7
17/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure: 7.13$(e'ii' !ra9it8 A((aratus Figure: 7.14@9en
=ro'e+ure:
• The sample of the aggregate is immersed in water for 08hrs to essentially fill all the
pores$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page135
-
8/9/2019 Experimental Work CHP 7
18/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure: 7.15 Aggregates $a(le an+ r8ing #o&el
• :emove the test sample from the water and roll it in a large absorbent cloth until all visible
films of water are removed$ 'ipe the larger particles individually$
Figure: 7.16"olling o oist aggregates
! moving stream of air is permitted to assist in the drying operation$ Ta(e care to avoid
evaporation of water from aggregate pores during the surface7drying operation
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page137
-
8/9/2019 Experimental Work CHP 7
19/47
-
8/9/2019 Experimental Work CHP 7
20/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
#ale 7.3: Calculation of pecific Dravity
A((arent s(e'ii'
gra9it8
$(e'ii' !ra9it8
@9en r8
$(e'ii' !ra9it8 in
$$
=er'entage
Asor(tion
> A
A−C G A
B−C GB
B−C GB− A
A X 100
G4 .95
4 .95−3.168 G4.95
5.022−3.168 G5.022
5.022−3.168G
5.022−4.954.95
X 100
G 0$39 G 0$=3 G 0$34 G 4$81 R
"esult: 6ercentage !bsorption of our materials is 4$81 R which is acceptable
7.4 Mi esign =ro'e+ure:
$te( 1. Choi'e o slu(
#A% 7.4::ecommended slumps for various types of construction
!s we have consider concrete for :C -eams, so we select slump from table 3$8$
From table 3$85
lump )max G 4in
$te( 2. Choi'e o aiu noinal sie o aggregate
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page13
-
8/9/2019 Experimental Work CHP 7
21/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
'e perform a sieve analysis on coarse aggregates according to !TM C 42=, so by
usingDrading :e&uirement for Coarse !ggregates !TM C 22, weconcluded that this grading of
aggregates satisfy the si.e =3$
From table)sieve analysis
• Maximum nominal si.e of aggregates G 34 in
$te( 3. stiation o iing &ater an+ air 'ontent
#ale 7.5: !pproximate mixing water and air content re&uirements fordifferent slumps and
nominal maximum si.es of aggregates
For non7air entrained concrete, we deter mine the &uantity of water by slump and maximum
nominal si.e of coarse aggregates from table 3$1$ $
From table 3$1$
• !mount of water for non7air entrained concrete G 28> lbyd 2
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page140
-
8/9/2019 Experimental Work CHP 7
22/47
-
8/9/2019 Experimental Work CHP 7
23/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
$te( 6. stiation o 'oarse aggregate 'ontent
#ale , 7.7: Aolume of coarse aggregate per unit of volume of concrete
'e determine the volume of coarse aggregates per unit volume of concrete from Table 3$3 by
comparing nominal maximum si.e of aggregate with fineness modulus of fine aggregates$
ominal maximum si.e of aggregates G 28 in
Fineness modulus of fine aggregates G 0$3
From Table3$3$5
•
Aolume of coarse aggregate per unit of volume of concrete G >$=2
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page142
-
8/9/2019 Experimental Work CHP 7
24/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
$te( 7. stiation o &eight o resh 'on'rete
#ale 7.0: First estimate of weight of fresh concrete
'e determine the weight of fresh concrete for non7air entrained concrete from table 3$9$-y using
nominal maximum si.e of aggregates$
ominal maximum si.e of aggregates G 28 in
From Table 3$95
•
First estimate of weight of fresh concrete G 2O=> lbyd
2
$te( 0.ensit8 o 'oarse aggregates
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page143
-
8/9/2019 Experimental Work CHP 7
25/47
-
8/9/2019 Experimental Work CHP 7
26/47
-
8/9/2019 Experimental Work CHP 7
27/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
• This test method covers determination of slump of hydraulic7cement concrete, both in the
laboratory and in the eld$
• This test method is considered applicable to plasticconcrete having coarse aggregate up to
4$1 in$ @23$1 mmB insi.e$ +f the coarse aggregate is larger than 4$1 in$ @23$1 mmB insi.e,the test method is applicable when it is performed on thefraction of concrete passing a 4$1
in$ @23$17mmB sieve, with thelarger aggregate being removed in accordance with the
sectiontitled J!dditional 6rocedure for Large Maximum i.e !ggregate ConcreteK in
6ractice C 430$
A((aratus
Mold
Tamping :od
Measuring evice
coop
Figure: 7.17 lump test apparatus
#erinologies:
Colla(se slu(:
+n a collapse slump the concrete collapses completely$
$hear slu(:
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page145
-
8/9/2019 Experimental Work CHP 7
28/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
+n a shear slump the top portion of the concrete shears off and slips sideways$
#rue slu(:
+n a true slump the concrete simply subsides, (eeping more or less to shape$
Figure: 7.10 Types of slump
=ro'e+ure
• The internal surface of the mold is thoroughly cleaned andapplied with a light coat of oil$
• The mold is placed on a smooth, hori.ontal, rigid and nonabsorbentsurface$
• The mold is then filled in three layers with freshly mixedconcrete, each approximately to
one7third of the height ofthe mold$
• Each layer is tamped 01 times by the rounded end of the tamping rod )stro(es are
distributed evenly over the cross7section$
• !fter the top layer is rodded, the concrete is struc( off thelevel with a trowel$
• The mold is removed from the concrete immediately byraising it slowly in the vertical
direction$
• The difference in level between the height of the moldandthat of the highest point of the
subsided concrete ismeasured$
• This difference in height is the slump of the concrete$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page147
-
8/9/2019 Experimental Work CHP 7
29/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure:7.10 lump measuring
@ser9ation< Cal'ulation:
lump G /eight of cone 7 /eight of subsided concrete cone
G 8$2 in
ee from table 3$8lump is ?#N
7.4.2 $tan+ar+ #est Metho+ or the ensit8 ;Dnit *eight) o resh Con'rete
;A$#M esignation C130 C130M)61
$'o(e
• This test method covers determination of the density of freshly mixed concrete
• Unit weight was the previous terminology used to describe the property determined by this test
method, which is mass per unit volume$
A((aratus
• -alance
•
Tamping :od• +nternal Aibrator
• Measure
• tri(e7?ff 6late
• Mallet
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page146
-
8/9/2019 Experimental Work CHP 7
30/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure: 7.1EMold for Cylinders
=ro'e+ure
:odding
• 6lace the concrete in the measure in three layers of approximately e&ual volume$ :od
each layer with 01 stro(es of the tamping rod when nominal >$17ft 2 @487LB or smaller
measures are used, 1> stro(es when nominal 47ft2 @097LB measures are used, and one
stro(e per 2 in0 @0> cm2B of surface for larger measures$ :od the bottom layer through7
out its depth but the rod shall not forcibly stri(e the bottom of the measure$ istribute the
stro(es uniformly over the cross section of the measure and for the top two layers,
penetrate about 4 in$ @01 mmB into the underlying layer$ !fter each layer is rodded, tap the
sides of the measure 4> to 41 times with the appropriate malletusing such force so as to
close any voids left by the tamping rod and to release any large bubbles of air that may
have been trapped$ !dd the nal layer so as to avoid overlling$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page14
-
8/9/2019 Experimental Work CHP 7
31/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
tri(e off plate
• !fter consolidation, stri(e7off the top surface of the concrete and nish it smoothly with
the Vat stri(e7off plate using great care to leave the measure %ust level full$
Cleaning and 'eighing
• !fter stri(e7off, clean all ex7 cess concrete from the exterior of the measure and
determine the mass of the concrete$
@ser9ation < 'al'ulation
Aolume of cylinder )measure G>$4O= ft2
'eight of empty cylinder )measure G O$112 (g
'eight of cylinder P fresh concrete G 02$2 (g
'eight of fresh concrete G 02$2 O$112
G 42$383 (g
ensity Gweight of freshconcrete
volumeof culinder
G13.747
0.196 (gft2
G 3>$48 (gft2
G 3>$48 x2.2046
0.037037 lbyd2
G 8438$9O lbyd2
ee from table 3$9, density of fresh concrete is ?#N
7.4.3 $tan+ar+ =ra'ti'e or Maing an+ Curing Con'rete #est $(e'iens in
the %aorator8
;A$#M +esignationC 1E2C 1E2M)62
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page10
-
8/9/2019 Experimental Work CHP 7
32/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
$'o(e < $ignii'an'e
• This practice covers procedures for ma(ing and curingtest specimens of concrete in the
laboratory under accuratecontrol of materials and test conditions using concrete that
canbe consolidated by rodding or vibration• This practice provides standardi.ed re&uirements forpreparation of materials, mixing
concrete, and ma(ing andcuring concrete test specimens under laboratory conditions$
A((aratus
• Molds )=x40 in
• Tamping :ods
• Mallets
• +nternal Aibrator
=ro'e+ure
Maing $(e'iens
6lace of Molding
• Mold specimens as near as practicableto the place where they are to be stored during the
first08 h$ +f it is not practicable to mold the specimens where theywill be stored, move
them to the place of storage immediatelyafter being struc( off$ 6lace molds on a rigid
surface free fromvibration and other disturbances$ !void %arring, stri(ing, tilting,or
scarring of the surface of the specimens when moving thespecimens to the storage place
6lacing of concrete5
• 6lace the concrete in the molds using ascoop, blunted trowel, or shovel$ elect each
scoopful, trowelfull,or shovelful of concrete from the mixing pan to ensurethat it is
representative of the batch$ +t may be necessary toremix the concrete in the mixing pan
with a shovel or trowel toprevent segregation during the molding of specimens$ Movethe
scoop or trowel around the top edge of the mold as the concrete is discharged in order to
ensure a symmetricaldistribution of the concrete and to minimi.e segregation ofcoarseaggregate within the mold$ Further distribute the concreteby use of a tamping rod prior to
the start of consolidation$+n placing the final layer the operator shall attempt to add
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page11
-
8/9/2019 Experimental Work CHP 7
33/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
anamount of concrete that will exactly fill the mold aftercompaction$ o not add non
representative samples of concreteto an under filled mold$
umber of Layers5
•
Ma(e specimens in layers as indicated in Table
Consoli+ation
Rodding
• 6lace the concrete in the mold, in there&uired number of layers of approximately e&ual
volume$ :odeach layer with the rounded end of the rod using the number of stro(es and
si.e of rod specified in Table given below$ :od the bottom layer throughout its depth$
istribute the stro(es uniformly over the cross section of the mold and for each upper
layer allow the rod to penetrate through the layer being rodded and into the layer below
approximately 4 in$ @01 mmB$ !fter each layer is rodded, tap the outsides of the mold
lightly 4> to 41 times with the mallet to close any holes left by rodding and to release any
large air bubbles that may have been trapped$ Use an open hand to tap light7gage single7
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page12
-
8/9/2019 Experimental Work CHP 7
34/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
use molds which are susceptible to damage if tapped with a mallet$ !fter tapping, spade
the concrete along the sides and ends of beam and prism molds with a trowel or other
suitable tool$
Curing
!fter 08 hrs$specimens are de7moulded and immersed in curing tan($
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page13
-
8/9/2019 Experimental Work CHP 7
35/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure: 7.2-Curing Tan(
@ser9ation < Cal'ulation:
'e casted O specimen of concrete cylinder and these concrete specimens are tested after 3, 48,W
09 days$ The testing procedure is given below$
7.4.4 $tan+ar+ Metho+ o #est or Co(ressi9e $trength o C8lin+ri'al
Con'rete $(e'iens
;A$#M esignation: C 3EC 3EM)63
$'o(e < $ignii'an'e:
• This test method covers determination of compressive strength of cylindrical concrete
specimens such as molded cylinders and drilled cores$ +t is limited to concrete having a
unit weight in excess of 9>> (gm2 )1> lbft2$
• Aalues obtained will depend on the si.e and shape of the specimen, batching, mixing
procedures, the methods of sampling, molding, and fabrication as well as the age,
temperature, and moisture conditions during curing$
• The results of this test may be used as a basis for &uality control of concrete
proportioning, mixing, and placing operations determination of compliance with
specification and control for evaluating effectiveness of admixtures and similar uses$
A==A"A#D$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page14
-
8/9/2019 Experimental Work CHP 7
36/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Testing Machine
Figure: 7.21Compressive trength testing machine
=ro'e+ure:
• Compression tests of moist7cured specimens shall be made as soon as practicable after
removal from moist storage$
•
Test specimens shall be (ept moist by any convenient method during the period betweenremovals from moist storage and testing$ They shall be tested in the moist condition$
• !ll test specimens for a given test age shall be bro(en within the permissible time
tolerances prescribed as follows5
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page1
-
8/9/2019 Experimental Work CHP 7
37/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
• Placing the Specimen5 6lace the plain )lower bearing bloc(, with its hardened face up,
on the table or platen of the testing machine directly under the spherically7seated )upper
bearing bloc($ 'ipe clean the bearing faces of the upper7 and lower7bearing bloc(s and
of the test specimen and place the test specimen on the lower bearing bloc( • Zero Verification and Block Seating 5 6rior to testing the specimen, verify that the load
indicator is set to .ero$ +n cases where the indicator is not properly set to .ero, ad%ust the
indicator$ !s the spherically7seated bloc( is brought to bear on the specimen, rotate its
movable portion gently by hand so that uniform seating is obtained$
• Rate of Loading 5 !pply the load continuously and without shoc($
The load shall be applied at a rate of movement )platen to crosshead measurement
corresponding to a stress rate on the specimen of >$01 H >$>1 M6as )21 H 3 psis The
designated rate of movement shall be maintained at least during the latter half of theanticipated loading phase$
• uring application of the first half of the anticipated loading phase, a higher rate of
loading shall be permitted$ !pply the higher loading rate in a controlled manner so that
the specimen is not sub%ected to shoc( loading$
• o not ad%ust the rate of movement )platen to crosshead as the ultimate load is being
approached and the stress rate decreases due to crac(ing in the specimen$
• !pply the compressive load until the load indicator shows that the load is decreasing
steadily and the specimen displays a well7defined fracture pattern
• Usually following type of fracture pattern are formed$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page15
-
8/9/2019 Experimental Work CHP 7
38/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure: 7.22 Fracture 6attern
Figure: 7.23Capping of cylinder
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page17
-
8/9/2019 Experimental Work CHP 7
39/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure: 7.24Testing of cylinder
@$"GA#I@N < CA%CD%A#I@N
#ale , 7.E:Compressive strength of concrete after 3 days
$r no Casting +ate #esting +ate iaeter
;)
Area
;2)
H'
;M(a)
1 0>7>8748 037>8748 41> 43==0$1 04$0
2 0>7>8748 037>8748 41> 43==0$1 00$8
3 0>7>8748 037>8748 41> 43==0$1 02$2
fXcavg G00$2 Mpa)=2$34R of strength 21Mpa
#ale , 7.1-:Compressive strength of concrete after 48 days
$r no Casting +ate #esting +ate iaeter
;)
Area
;2)
H'
;M(a)
1 0>7>8748 >87>1748 41> 43==0$1 20$0
2 0>7>8748 >87>1748 41> 43==0$1 22$0
3 0>7>8748 >87>1748 41> 43==0$1 22$3
fXcavg G22Mpa )O8$2>R of strength 21Mpa
#ale , 7.11:Compressive strength of concrete after 09 days
$r no Casting +ate #esting +ate iaeter Area FH'
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page16
-
8/9/2019 Experimental Work CHP 7
40/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
;) ;2) ;M(a)
1 0>7>8748 497>1748 41> 43==0$1 21$0
2 0>7>8748 497>1748 41> 43==0$1 29$=
3 0>7>8748 497>1748 41> 43==0$1 29$3
fXcavg G23$1 Mpa)greater than the re&uired strength of 21Mpa
Figure: 25;a) Cylinder testing after 09 days
fX' 21$0 Mpa after 09 days
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page1
-
8/9/2019 Experimental Work CHP 7
41/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Figure: 27;) Cylinder testing after 09 days
fXc 29$= Mpa after 09 days
Figure: 27;') Cylinder testing after 09 days
fXc 29$3 Mpa after 09 days
Final "esult::e&uired ratio of cement, sand, and coarse aggregate for 1>>> psi )21 Mpa at 09 days strength is
45 4$=5 0$1$
o we will proceed to our main ob%ective of strengthening of beam, so we want to cast a beam, for
this purpose we first design a beam in next step given below$
7.' (tr"ct"ra# $e)in o& *eam+
Five :C -eam with constant cross section )=KxO$1K and length )8=K, having same
@=8Breinforcement in all beams as 0Y9 bars on tension side and 0Y2 on compression side as hanger
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page150
-
8/9/2019 Experimental Work CHP 7
42/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
bar$ !nd Y2 Z 2$=K cc stirrups for shears throughout the length except central portion of =K of
the beam$grade of steel is 8>$sections of beam is shown in figure given below$
7.6 ,e)in an$ &a*rication o& )tee# mo#$+
8e -e(g& a ('ee, %!,- a$$!#-&g '! -%e&(!& !" #e9+#e- ea% *3:;10e#$!%e +,?&g !"
%!,- e +(e- ('ee, e A&- @&()&g ( -!&e ') a&'
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page151
-
8/9/2019 Experimental Work CHP 7
43/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
Fi"re+ 7.6S'ee, "#a%e!#?
7.7 Ca)tin an$ c"rin o& *eam)+
F!# $a('&g !" ea%( ('ee, "!#%!#? a( +(e- 8e %a?e a $!&$#e'e
%. a$$!#-&g '! ASTM -e(g&a'!& C 12C 12M "!# $a('&g !" RC ea%(
*!&e $!&'#!, ea% 4 ('#e&g')e&&g ea%(/ a&- 5 $!&$#e'e $=,&-e#C!&$#e'e %. *1152/ = eg)' a( %a-e & $!&$#e'e %.e# a&- !+#e-
%a&+a,,= & ('ee, %!,-( C!%a$'!& a( -!&e = >#a'!# +' e"!#e
!+#&g '! ('ee, %!,- e a,= #!e# !,&g !& &'e#&a, (+#"a$e !" %!,- (!
')a' ea% -! &!' ('$? ') %!,- a"'e# #e%!>a, a&- "!#%!#? ea(,= #e%!>e
A&- a,(! (ee ')a' ')e#e ( &! ,ea?age "#!% %!,- '! a>!- ,ea?age "#!% %!,-
e a,= g#ea(e !& -e#e&' !&'( & %!,- A"'e# 24 )!+#( ea% %!,- a&-
$!&$#e'e $=,&-e# e#e !e&e- A&- a,, g#ee& )a#-e&e- ea% e#e #ae-
& )e((a& $,!') "!# $+#&g a&- $!&$#e'e $=,&-e# e#e +''e- & $+#&g 'a&?
C!&$#e'e $=,&-e# e#e 'e('e- a' 7 14 a&- 26 -a=( +' ea% e#e ,e"' "!#')e &e.' 26 -a=( '! a$)e>e ')e -e(#e- ('#e&g') "!# ('#e&g')e&&g a&-
'e('&g
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page152
-
8/9/2019 Experimental Work CHP 7
44/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
#ale , 7.12: Compressive strength of concrete after 3 days
$r no Casting +ate #esting +ate iaeter
;)
Area
;2)
FH'
;M(a)
1 0=7>1748 >07>=748 41> 43==0$1 00$1
2 0=7>1748 >07>=748 41> 43==0$1 00$3
fXcavg G00$= Mpa)=8$34R of strength 21Mpa
#ale , 7.13: Compressive strength of concrete after 48 days
$r no Casting +ate #esting +ate iaeter
;)
Area
;2)
FH'
;M(a)
1 0=7>1748 >O7>=748 41> 43==0$1 20$4
2 0=7>1748 >O7>=748 41> 43==0$1 22$2
fXcavg G20$3Mpa )O2$80R of strength 21Mpa
#ale , 7.14: Compressive strength of concrete after 09 days
$r no Casting +ate #esting +ate iaeter
;)
Area
;2)
FH'
;M(a)
1 0=7>1748 027>=748 41> 43==0$1 2=$4
2 0=7>1748 027>=748 41> 43==0$1 29$=
fXcavg G23$21 Mpa )greater than the re&uired strength of 21Mpa
7.! (trenthenin o& RC eam)+
S'#e&g')e&&g !" RC ea%( ( -!&e ') "!,,!&g ('e(
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page153
-
8/9/2019 Experimental Work CHP 7
45/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
7.!.1 ("r&ace preparation o& *eam)+
T)e e)a>!# !" $!&$#e'e e,e%e&' ('#e&g')e&e- ') Fe##!$e%e&' ,a%&a'e(
( )g),= -ee&-e&' !& #!e# #ea#a'!& a&- #!@,&g !" $!&$#e'e (+#"a$e
e$a+(e "!# ('#!&g !&- e'ee& $!&$#e'e a&- "e##!$e%e&'A,, (+#"a$e(%+(' e ')!#!+g),= $,ea&e- a&- #ea#e- A,, ,!!(e a#'$,e( ,a'a&$e -+('
C+#&g $!%!+&-( !, g#ea(e %+(' e #e%!>e- " g!!- !&- ('#e&g') ( '!
e a$)e>e- I" !, g#ea(e "a' e'$ a#e #e(e&' ')e= ()!+,- e #e%!>e-
e"!#e ('a#'&g a&= !')e# "!#% !" #ea#a'!&
S! "!# ')( #ea(!& !''!% *'e&(!& (-e/ (+#"a$e !" 4 ea%( e#e g#&-e- a&-
#!+g)e#
6.7.2 %AIN! AN A==%ICA#I@N @F F""@CMN# MA#"IA% @N #@= @F
# AM
trengthening of the specimens by using following option$
• Laying a pair of hexagonal and rectangular mesh ontension side throughout the
length of beam$
• Laying a pair of one rectangular and two hexagonal meshon tension side throughout
the length of beam$
• Laying two pair of rectangular and hexagonalon tension side throughout the length of the
beam$
• Laying a pair of one rectangular and hexagonal mesh on tension side throughout
the length of the beam and also along the both sides of the beam$
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page154
-
8/9/2019 Experimental Work CHP 7
46/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
F!,,!&g 'e('( a#e e#"!#%e-
Bea% &! C!&$#e'e
$=,&-e#
('#e&g')
*?(/
!,+%e
"#a$'!&
Se$@$
(+#"a$e
S,+%
>a,+e
1 73 071 00346 63
B2 140 00565 41
STRENGTHENING OF REINFORCED CONCRETE BEAM USING FERROCEMENT CAST INSITULAMINATES
DANISH AZAD AHTESHAM ALTAF IMRAN ASLAM MUHAMMAD UMER ABDULLAHKHAN Page15
-
8/9/2019 Experimental Work CHP 7
47/47
CHAPTER NO 7EXPERIMENTAL PROGRAM
B3
B4
131
1
0063
00367
67
60
top related