ece alignment status for 2w siam jama meeting 31-october 2014
Post on 24-Dec-2015
221 Views
Preview:
TRANSCRIPT
ECE Alignment status for 2w
SIAM JAMA MEETING31-OCTOBER 2014
Principles of alignment• SIAM has following preference for aligning the Indian
regulation with:1. GTR2. ECE Regulation3. EU directive (if GTR or ECE R do not exist for that subject)4. Any other foreign national regulation if none of the above
exist.• While aligning with GTR:– Where options are permitted in GTR. The option best
suited for India is adopted:• E.g. In GTR 3 for brakes. PBC measurement as per
ASTM.• Approval and marking schemes as per Indian practice.
Principles of alignment with ECE R• The basic characteristics and performance values are taken
with out change. E.g.– Photometric values for light and light signalling devices– Stopping distances for brakes.
• But every feature is studied w.r.to1. Is the feature essential for Indian conditions:
– If yes, included as mandatory.2. Are the benefits of feature doubtful in Indian conditions?
– If yes, included as optional. E.g. AHO (at the time when AIS 009 was revised)
Principles of alignment with ECE R3. Will the ECE feature pose a safety hazard in Indian
condition?• If yes, exclude them. E.g– Headlamps with passing beam pattern for both
kinds of traffic with necessary adjustment to be done by the driver depending on which traffic pattern he is in.
– Allowing headlamps with main beam and passing beam to be approved only for passing beam.
4. Is the non ECE features in current regulation really needed?• If no, exclude them from the standard E.g. many of
the environmental and durability tests for light and light signalling devices.
Transitional Provisions• Transitional provision principles (AIS 00)
permit:– Use of the revised standard, after it is approved by CMVR
TSC, in lieu of the old version.– Changes in ECE issued as supplements (i.e. as per ECE old
type approvals continue to be valid) are allowed to be used with permission of Chairman AISC.
– However, changes in ECE issued as “series of amendments” (i.e. as per ECE re-type approval is needed) are not permitted.
Benefits • These principles and transitional provisions
permit• Use of parts complying with ECE regulations to
be used, subject to:– ECE Regulation Series of amendments up to the
AIS/BIS level.– Additional Indian Approval process remains.– Not Applicable when an “ISI” marking has become
mandatory.
Current status• The ECE regulations and current status are
tabulated in subsequent slides.• Some of the standards are approved by CMVR TSC,
but not yet notified.– But are permitted to be used because of transitional
provisions.• There have been changes in ECE R, in many of such
cases, but• SIAM prefers not to propose any changes to these
AIS/BIS till these standards are notified.
AIS/BIS implemented/notified (1/4)
• No need felt by SIAM to take up these standards for any Revision
ECE R Subject AIS/BIS10-02 EMC AIS 004 PART 339-00 Speedometer IS-11827-200875 Rev 1 Tyres IS 15627 : 200578-02 Braking IS: 14664: 1999
ECE R Subject AIS/BIS03-02 Retro Reflector AIS 057 REV 119-03 Front Fog lamp (optional) AIS 012 PART 1 REV 1R28 Horn Installation (Optional) IS 15796:200837-03 Filament lamps AIS 034 PART 138-0 Rear fog lamp AIS 012 PART 2
46-02 Rear view mirror (2W with body)
Device AIS 001 Pt.2Installation AIS 002 Pt 2
50-00 Signalling lamps AIS 010 Part 3, Rev 153-01 Installation of lights AIS 009 Rev 1GTR 12(R60)
Tell tale symbols and controls(Aligned with GTR 12)
AIS 126
GTR 3(78-03)
Braking(Aligned with GTR 3)
IS: 14664: 2010
AIS/BIS implemented/notified (2/4)
• Changes to amend for further alignment will be proposed by SIAM only after these standards are notified.
• SIAM has no idea when these will be notified
ECE R Subject AIS/BIS81-00 Rear view mirror (2W w/o body) Device AIS 001 Pt.2
Installation AIS 002 Pt 287-00 DRL AIS 012 Part 1098-00 Headlamps with gas discharge light
sourcesAIS 010 PART 4 REV 1
99-00 Gas-discharge light sources AIS O34 PART 2 REV 1112-00 Asymmetric headlamps AIS 010 PART 1 REV 1113-00 Symmetric headlamps AIS 010 PART1 REV 1GTR 12 Tell tale symbols and controls AIS 126
AIS/BIS implemented/notified (3/4)
• Even though the lead times were agreed in the CMVR TSC, may get changed at the time of notification.
• In the case of IS14664, availability of test track is also a constraint.• SIAM expects to firm up the proper definition for new model shortly.
Lead time starting from 1st April or 1st October, which ever occurs from date of notification
AIS New model Existing model009010 Pt 1010 pt 2010 pt 3
24 months 48 months
IS: 14664: 2010 18 months 42 months
AIS 126 24 months 36 monthsALL OTHERS 18 months 24 months
AIS/BIS implemented/notified (4/4)
AIS/BIS taken up for revision for further alignment
ECE R Subject AIS/BIS Status41-04 Noise New IS in
place ofIS 3028
BIS committee Finalized.
75 Rev 1 Tyres IS 15627 BIS has agreed to take up28 Horn IS I884 BIS committee working on
this.128-00 LED NEW AISC working on this
NO ROAD MAP AVAILABLE FOR COMPLETION OF ACTIVITIES
DISCUSSIONS
top related