ece 3130 – digital electronics and design

Allan Guan

ECE 3130 – Digital Electronics and Design

Lab 4VTC and Power Consumption

Fall 2012

Allan Guan

Today’s Lab

• Plot VTC for an inverter• Check if VTC is symmetric• If VTC is not symmetric we will find Wp/Wn

such that the VTC for an inverter is symmetric

Allan Guan

What is VTC?• Voltage Transfer Curve• Plots output voltage vs. input voltage• Symmetry – when a line plotted through the origin and Vdd/2 intersects the VTC

at Vdd/2

Allan Guan

Plotting the VTC• Open your inverter test bench from the 1st lab• Replace the pulse input with a DC source• Use the net label to label “in” and “out” of the inverter

Allan Guan

Simulation Settings• Select DC sweep analysis• Set the source name to the name of your inverter’s input source

(IMPORTANT: add a ‘v’ in front of the name!)• Click OK, do NOT simulate

Allan Guan

T-Spice• Click the “Open in T-Spice” button (T-icon to the right of the green play button)• Add the following lines of code• Hit the green play button

That vertical line is just the cursor, ignore that

Allan Guan

The VTC is not symmetric

Allan Guan

Obtaining a Symmetric VTC

• Keeping the length and width of the NMOS fixed we can vary the width of the PMOS to obtain a symmetric curve

• To do so, we will perform a DC sweep like before but with the addition of the parametric sweep

Allan Guan

Setting up the Parametric Sweep

Allan Guan

Defining the pMOS width as a parameter

• In the T-Spice code, write .param width=3u• In the pMOS properties, change W=3u to

W=‘width’• Now, the pMOS width is defined by parameter

‘width’

Allan Guan

Your T-Spice code should look like this

Allan Guan

Parametric Sweep Waveform

Allan Guan

Designing with Symmetric VTC

• Click the trace to determine the width required for the symmetric VTC

• Record the width of the pMOS corresponding to the symmetric operating point (you should get 3.2u)

• Replace the inverter input with the original Pulse source

• Go back to simulation settings and uncheck the DC and parameter sweep and select Transient Analysis

• Open up the T-Spice command window and substitute this width for the pMOS and simulate

Allan Guan

Rise/Fall Times @ Symmetric Operation

• In the W-Edit window, go to the waveform calculator

• Click “Measures…” and select “rise time”• Type in a trace name and press “Measure”• With the same trace, measure the “fall time”• Since we changed the pMOS width to obtain a

symmetric VTC, the rise and fall times should be the same

Allan Guan

Power Consumption

• Now, we will use Tanner Tools to estimate the power consumption of a design

• We will also identify the sources of that consumption

Allan Guan

Power Consumption

• Simulate the circuit over 2 periods with fine resolution (2ns)

• Show the waveforms for:– The input and output voltages– The power provided by the power supply– The currents drawn from the power supply and

the capacitor

Allan Guan

Plotting Power and Current from the Transient Analysis

Get this capacitor from the Devices library

Allan Guan

Power Consumption @10 pF load and 10ns rise time

Allan Guan

Power Consumption @1 pF load and 10ns rise time

Allan Guan

Power Consumption @1 pF load and 1ns rise time

Allan Guan

Analysis

• Report numerical values of your results in tabular form.

• Can we vary the width of NMOS instead of PMOS in order to obtain symmetric VTC? If yes, should we increase or decrease it’s value keeping PMOS width fixed?

• On the VTC of the inverter, show the triode, saturation, and cut-off region. Which region is used for digital design and which one is used for analog design?

Allan Guan

Analysis (Continued)

• Do you obtain different values of power consumed on varying the load and rise/fall time of the pulse? Compare and analyze your results.