ec centrifugal fans - ebm-papst · 2015. 10. 7. · ec centrifugal fans backward curved, single...
Post on 11-Mar-2021
5 Views
Preview:
TRANSCRIPT
EC centrifugal fans backward curved, single inlet, Ø 560
Highlights: – 7-blade fan, 3-phase fan motor – 10 VDC max. output / 10 mA, 24 V external program input, 0-10 VDC / PWM control input – Integrated PID controller, control interface with SELV potential safely disconnected from the mains, RS485 MODBUS RTU technology – Over-temperature protected electronics / motor – Soft start, PFC passive, line undervoltage / phase failure detectionMaterial: Impeller: Aluminum sheet Rotor: Coated in black Electronic housing: Die-cast aluminum Assembly: Galvanized steel with aluminum postsMounting position: Shaft horizontal or rotor on bottom; rotor on top on request Condensate discharge holes: Rotor-side Direction of rotation: Clockwise, seen on rotor
(1) Nominal data at maximum load.
Measurement: LU-128639
Air performance measured as per: ISO 5801, Installation category A, without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LPA measured at 1m distance to fan axis. The values given are valid under the measuring conditions mentioned and may vary accoring to the actual installation situation. With any deviation to the standard set-up, the specific values have to be checked and reviewed once installed or fitted.
For detailed information on the measuring set-up, please contact ebm-papst.
Curvesn
rpm
Pe
W
I A
(460V)
I A
(230V)
LwAin
dB(A)
Nominal Data Air fl
ow
Nom
inal
vol
tage
rang
e
Freq
uenc
y
Pow
er in
put (
1)
Spee
d (1
)
Curr
ent d
raw
(1)
Tem
pera
ture
rang
e (1
)
Mas
s
Ingr
ess
prot
ectio
n ra
ting
Elec
trica
l wiri
ng d
iagr
am
UL
Type RadiPac Motor CFM VAC Hz Watts RPM A °C lbs
R3G560-AQ11-19F EG1R-240-560-60 M3G150-NA 10,113 200...240 50/60 4,500 1,750 12.2 -25...40 88 IP54 B Yes
R3G560-AQ04-09F EG1R-480-560-60 M3G150-NA 10,113 380...480 50/60 4,700 1,750 6.3 -25...40 88 IP54 B Yes
0 2.000 4.000 6.000 8.000 9.000 cfm
0
0
.4
0.8
1.2
1.6
2
2.
4
2
.8
3
.2
3
.6
4
4.4
4.8
5.
2
5
.6
in. w
g
2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 m3/h
pfs[Pa]
pfs[Pa]
pfs[Pa]
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
1
2
3
4
5
6
7
8
9
10
11
12A
A
A
A
A
A
A
A
A
A
A
A
13
14
15
16A
A
A
A
1
2
3
4
5
6
7
8
9
10
11
12A
A
A
A
A
A
A
A
A
A
A
A
13
14
15
16A
A
A
A
1750 3032 4.1 8.3 97
1750 3929 5.3 11.2 91
1750 4700 6.3 12.2 84
1750 4366 5.8 11.9 86
1450 1675 2.3 4.6 93
1450 2171 2.9 5.9 87
1450 2602 3.5 7.3 80
1450 2432 3.3 7.0 82
1150 836 1.1 2.3 88
1150 1083 1.5 3.0 82
1150 1298 1.7 3.7 75
1150 1213 1.6 3.5 76
EG1R-XXX-560-60
R3G560-AQXX-XXF
19.65(499)
24.8
03 ( 6
30)
29.528 (750)Ø .433 (11)8 PLACES
31.4
96 ( 8
00)
17.874(454)
22.9(582)
Depth of screw max. 20 mm
Cable diameter: min. 9 mm,max. 16 mm;tightening torque: 6±0.9 Nm
Tightening torque 3.5±0.5 Nm
Ø10.75 (273)Ø11.97 (304 ±0.5)
Ø12.76 (324)
Cable diameter: min. 4 mm,max. 10 mm;
tightening torque: 4±0.6 Nm Accessory part: inlet nozzle 64030-2-4013with a pressure tap not included in the standarscope of delivery; other inlet nozzles on request
4.45 (113)
6.3 (160)9.41 (239)
15.43 (392±2)
0.63(16)
0.08 (2)3.23(82)
Ø15.
55 (3
95)
Ø25.
04 (6
36)
Ø15.
16 (3
85)
Ø14.
96 (3
80)
Ø19.
29 (4
90)
Ø20.
28 (5
15)
Ø0.3
5 (9
(6x)
)
( )
Dimensions shown in inches (mm)
Dimensions shown in inches (mm)
top related