e3 flasher installation manual

E3 FLAHSER installation

on Slim PS3 First, we need prepare following item:

One PS3 which can downgrade to 3.55

E3 FLASHER Limited version with 8 accessory. (it will include universal screwer)

SLIM disassemble tutorial

1: Remove the four hexagon nut under the cover of PS3 bottom.

2: take out nut on the HD, and get out hardisk .

3: Remove the seal, and take off all nuts.

4: open Top cover

5: Take off the nuts beside power, and unplug power cable besides power, take out

powe Module.

6: Remove the black nut on the right of 220V power cable and the nuts on the top of

BD driver, please note the big and small size, especially the nut on driver is big, don’t

mixed when re-install.

7: Unplug all BD driver data cable

please note there has a data cable under the driver , becareful unplug it.

8: Unplug the front buttom board before take out BD driver. Please note only

disconnect with console, no need take out, because there has cable link to

mainboard.

And then cable take out BD DRIVER.

9: Unplug antenna, and remove from mainboard track, no need disconnect metal of

antenna, and unplug the front board together with cable.

Finally disconnect picture

10: You need take off four white nuts before take out mainboard.(white nut is fixed

for HD)

And then can take out mainboard

11: Remove all nuts from metal shade on the back of mainboard

Take out Metal shade

SLIM console solder tutorial:

following testing point showes the solder range

E3 FLASHER provide soft board special for SLIM console, you can install faster with

the testing point, no need any diagramme, and 100% safe without any problem.

Solder sequence

Solder SBCE point first, and solder SBE to fix soft board. If you can watch all testing

point in front it means correct location. And then solder VCC BVCC GND etc, please

note those point need heat little more time because of mainboard technology. And

then solder other point.

Recommend solder posture :

By the way, to fix soft board, you can use double-side tape as picture showes, and

stick on mainboard.

Completed

SLIM console remout tutorial

Now we need connect mainboard which installed soft board well to console again.

1: We need remout metal shade to mainboard, please note soft board need place

into HD warehouse.

After install metal shade correctly

In addition, for correctly solder , you can test with E3 FLASHER mainboard, check

installation testing tutorial

2: Place mainboard into case, please note soft board need across HD warehouse of

case first, to prevent damage soft board, and then place white and black nuts

correctly, and install anternna correctly.

2: Install buttom board and BD drive.

The buttom board need connect cable first, and don’t install on case because you

need install drive first

you need connect cable first at the bottom of drive , press connector carefully.

And connect external cable

Then install BD drive and another nut

At last install buttom board on mainboard

3: Install power moduel, please install the two nut well and then install power cable

4: After close the top cover, you need install all nuts which at the bottom (not include

nut on HD warehouse)

5: Install E3 flasher mainboard

the mainboard placed in the special metal shade

Put it into HD warehouse , just like install HD

And then ducked the connector on soft board into mainboard socket, you can press

from left to right with finger. You will hear clear sound from connector if you connect

correctly.

Install correctly

Push mainboard into HD warehouse, becareful otherwise it will damage connector of

SATA , or not connect corretly.

Then, install E3 FLASHER cover board into mainboard, don’t mistake the location.

Finally install nut of HD warehouse

If all is correct, you will see LED lighting after connect ps3 power (no need start PS3)

Finally, connect ESATA station, put original PS3 HD into esata station and setting

buttom on COVER BOARD to PS3 MODE, OFW.

the HD switching sequence is :

turn off PS3turn off esata station powerunplug PS3 power cableplace HD to

esata stationplug ESATA cable to ps3 plug PS3 power cablepower on esata

stationturn on ps3. If can turn on ps3 correctly, congratulate you are successful !