ddm install guide h13 hid hi/low kit (35w or...
Post on 02-Jan-2021
3 Views
Preview:
TRANSCRIPT
ddmT u n i n g
ddm
ddmT u n i n g
DDDDMM INSTALL GUIDE HH1133 HHIIDD HHii//LLooww KKiitt ((3355WW oorr 5555WW))
TTOOOOLLSS NNEEEEDDEEDD:: Standard or metric socket set. Depending on the vehicle.
Once your OEM H13 is removed from the
headlight assembly, you can install the H13
high/low HID bulb.
To do so, simply align the locking tabs on the
base of the bulb with the cutouts in the
headlight housing and twist into place.
NOTE: Always install the ground wire (-) first.
DDIIFFFFIICCUULLTTYY:: Easy Professional Install
PH 885588 556655 11774422 II DDDDMMTUNING.COM PAGE 11/5
RREEAADD FFIIRRSSTT:: Most H13 Hi/Low kits are relatively easy to install. Remove yourheadlight before you begin This will allow the HID kit to be installed much eas-ier. If removal of the headlight assembly is necessary please refer to your vehi-cle’s owners manual for instructions. Note: We are using a 2004 Ford F150 for ourinstall. ALWAYS START THIS INSTALL FROM THE SIDE OF THE CAR CLOSER TO THE VEHICLE’SBATTERY OR IF THERE IS NO BATTERY IN THE ENGINE BAY USE THE BATTERY CHARGINGPOINT IN ENGINE BAY, SEE OWNERS MANUAL.
11
22
Next we will begin to wire up the H/L wiring
harness. Its best to start with the battery ter-
minals. On the wiring harness there will be
one (+) and one (-) terminal ring. Install the
(+) terminal (red head shrink) to the (+) termi-
nal on the engine bay. Use a deep socket to
remove any nuts to allow terminal ring to
properly be installed. 55
Tighten down the nut on the positive termi-
nal, ensuring a solid connection.
Tighten down nut on (-) terminal, ensuring a
solid connection.
DDDDMM INSTALL GUIDE - HH1133 HHIIDD HHii//LLooww KKiitt ((3355WW oorr 5555WW))
PH 885588 556655 11774422 II DDDDMMTUNING.COM PAGE 22/5
Reinstall the nut with terminal ring in place. 66
77
44
Install the (-) terminal ring to the- terminal on
your battery.33
Next plug the 9006 connector from the wiring
harness into your ballast.
DDDDMM INSTALL GUIDE - HH1133 HHIIDD HHii//LLooww KKiitt ((3355WW oorr 5555WW))
PH 885588 556655 11774422 II DDDDMMTUNING.COM PAGE 33/5
We will now continue working with the
remaining plugs on your wiring harness. Plug
the H13 female plug from the wiring harness
into the male H13 plug from your OEM power
supply.
Pictured is (+) and (-) Terminals correctly
installed on to your battery.
Once you have completed that, plug corre-
sponding AMP connectors from HID bulb to
your ballast.
88
99
11 00
11 11
Then plug corresponding AMP connectors
from HID bulb to your ballast.
DDDDMM INSTALL GUIDE - HH1133 HHIIDD HHii//LLooww KKiitt ((3355WW oorr 5555WW))
PH 885588 556655 11774422 II DDDDMMTUNING.COM PAGE 44/5
Now that side is complete we can direct the
remaining wire from the wiring harness to the
opposite side of the car.
One again plug the 9006 connector from the
wiring harness into your ballast.
The last step on this side of the car is plugging
in your high/low function. To do so simply plug
in the 2 prong male/female connectors
together. The female plug will come from your
HID bulb, the male plug will come from your
wiring harness. 11 22
11 33
11 44
11 55
DDDDMM INSTALL GUIDE - HH1133 HHIIDD HHii//LLooww KKiitt ((3355WW oorr 5555WW))
PH 885588 556655 11774422 II DDDDMMTUNING.COM PAGE 55/5
The last step on the wiring harness is plugging
in your high/low function. To do so simply plug
in the 2 prong male/female connectors
together. Then using the tie wraps in the kit
secure the wiring harness.
At this point you may notice that the OEM H13
power supply on one side of the car is hang-
ing freely , and is not connected to the wiring
harness. Do not panic, the design of the
wiring harness bypasses the H13 connector
on one side of the car. Your bulbs will function
properly without this plug connected to the
wiring harness. Then test to see if the kit works
as designed, start with the lows, then flick on
the high beams. If everything looks good,
reinstall your headlight and enjoy.
11 66
top related