d633/d634 direct drive servovalves€¦ · d633/d634 direct drive servovalves proven to run faster,...
Post on 08-Apr-2020
20 Views
Preview:
TRANSCRIPT
D633/D634 DIRECT DRIVE SERVOVALVES
PROVEN TO RUN FASTER,POSITION BETTER ANDDRIVE THROUGH DIRT FORWOOD PROCESSING.
The D633 and D634 Series are DirectDrive Valves (DDV) with electric closedloop spool position control. Thesevalves are throttle valves for 3-, 4-, and2x2 way applications. They are suitablefor electrohydraulic position, velocity,pressure and force control systems,including those with high dynamicresponse requirements.
The valve model numbers listed in thechart on the back were specificallydesigned to withstand the harshenvironment, vibration, and shock loadsfound in wood/lumber processingplants.
The spool drive device is a permanentmagnet linear force motor that canactively stroke the spool from its springcentered position in both directions.This is an advantage when compared toproportional solenoids with one forcedirection only. The closed loop spoolposition electronics and pulse widthmodulated (PWM) drive electronics areintegrated into the valve and require a24VDC power supply.
Benefits for the Wood ProcessingIndustry
n Moog’s Direct Drive Valves (DDV)have spool driving forces that aretwice those of a servo solenoid valve
n Increased operation at limits (at highpressure drops)
n Directly driven by a permanentmagnet linear force motor with highforce level
n No pilot oil flow requiredn Pressure independent dynamic
performancen Low hysteresis and low thresholdn Low current consumption at and
near hydraulic nulln Standardized spool position
monitoring signal with low residualripple
n Electric null adjust n Can be configured with an offset
fail-safe mode; with loss of supplyvoltage, broken cable or emergencystop, the spool shifts to apredetermined offset flow condition
WHAT MOVES YOUR WORLD
Proportional solenoid systems requiretwo solenoids with more cabling for thesame function. Another solution uses asingle solenoid, working against a spring.In case of current loss in the solenoid, thespring drives the spool to the end positionby passing through a fully open position.This can lead to uncontrolled loadmovements.
Operation of the Direct Drive ValvesThe position control loop for the spool with position transducer and linear force motor isclosed by the integrated electronics. An electric signal corresponding to the desiredspool position is applied to the integrated electronics and produces a pulse widthmodulated (PWM) current to drive the linear force motor. An oscillator excites the spoolposition transducer (LVDT) producing an electric signal proportional to spool position.
The demodulated spool position signal is compared with the command signal and theresulting spool position error causes current in the force motor coil until the spool hasmoved to its commanded position, and the spool position error is reduced to zero. Theresulting spool position is thus proportional to the command signal.
Technical Data Direct Drive Valves
Direct Drive Valve Hydraulic Symbol
Valve pressure drop ∆p [bar]
Flow
rate
Q [l
/min
]
∆pm
ax=
350
bar (
5000
psi
)
Flow Signal Characteristic Curve
Contact MoogAmericas +1-716-652-2000Europe +49-7031-622-0Pacific +81-463-553615
Model Number
Type Code
Notes
Flow (gpm @1000 psitotal drop)
Flow (gpm @ 150 psitotal drop)
Max Supply Pressure(on main stage)
Null Cut
Fail-Safe
Seal Type
Elec Conn
Input Command
Power Supply
D633-303B
R02KO1M0NSM2
1
0.5
5000
Servo
0 to 1.5% overlap
Spool in
Mid-Position
Buna
7-Pin
+/-10VDC
+24VDC
For your nearest Moog location visit our websitewww.moog.com/industrial/globallocator
©2007 Moog IndustrialAll rights reserved. For legal notices, seemoog.com/disclaimersFlyerDDV_TJW/0407
D633-317B
R04KO1M0NSM2
2
1
5000
Servo
0 to 1.5% overlap
Spool in
Mid-Position
Buna
7-Pin
+/-10VDC
+24VDC
D633-308B
R08KO1M0NSM2
5
2
5000
Servo
0 to 1.5% overlap
Spool in
Mid-Position
Buna
7-Pin
+/-10VDC
+24VDC
D633Z570B
R16KO1M0NSM2
Vibration resistantinternal connector
10
4
5000
Servo
0 to 1.5% overlap
Spool in
Mid-Position
Buna
7-Pin
+/-10VDC
+24VDC
D634Z395C
R24KO2M0NSM2
Vibration resistantinternal connector
16
6
5000
Servo
0 to 1.5% overlap
Spool in
Mid-Position
Buna
7-Pin
+/-10VDC
+24VDC
D634Z549A
R40KO2M0NSM2
Vibration resistantinternal connector
26
10
5000
Servo
0 to 1.5% overlap
Spool in
Mid-Position
Buna
7-Pin
+/-10VDC
+24VDC
D634-1019
P24KA6MOVSM2
16
6
5000
Proportional
0 to 3% overlap
Spool in
Mid-Position
Fluorocarbon
7-Pin
+/-10VDC
+24VDC
D634-1003
P40KA6MOVSM2
26
10
5000
Proportional
0 to 3% overlap
Spool in
Mid-Position
Fluorocarbon
7-Pin
+/-10VDC
+24VDC
D634Z1044
P60KA6MOVSM2
Vibration resistantinternal connector
42
16
5000
Proportional
0 to 3% overlap
Spool in
Mid-Position
Fluorocarbon
7-Pin
+/-10VDC
+24VDC
top related