controladores crompton greaves
Post on 18-Nov-2014
198 Views
Preview:
TRANSCRIPT
DIGICONSeries
CONTROLLERS,TIMERS, COUNTERS& HOUR METERS
At the cutt
ing edge o
f
current c
ontrol
INDEX
Sr. Product Page
1 Digital Controllers, Leganza 1
2 Digital Timers, Eliro 4
3 Digital Timer-Cum-Counters, Excello 6
4 Digital Hour Meters and Counters 12
Supply from ISO 9001Certified Unit
ACCESSORIES
8GDDT1 : Leganza Software CD
8GDDT2 : Serial Interface Cable
8GDDT3 : Memory Card
8GDDT4 : Instruction Manual
8GDDT5D : Extension Module for 110-240V AC.
8GDDT5E : Extension Module for 12-24V AC.
1
FRONT DISPLAY
1 2 analogue inputs for 88DDT0 or 88DDT8, otherwise digital.
2 6 digital inputs
3 Power supply terminals, L, N for 87DDT0 and 87DDT8 andSup + and Sup - for 88DDT0 and 88DDT8
4 LC display
5 Digital outputs
6 Keypad
7 Interface for Memory Card or PC cable located on lowerside and not seen in the front view.
8 Terminals for Extension Module.
Note : Colours are used on the above diagram for indicationpurpose only.
FEATURES
• Offers integrated, ready to use, wide rangeprogrammable functions to include 8 Timers,8 Counters, 4 Time Switches, 4 Analogue functionsand real time clock.
• 64 or 250 lines ladder diagram programming withkey pad.
• 8 digital inputs for maintained-contact switches,momentary-contact switches, sensors etc. or 6 digitaland 2 analogue inputs.
• 4 relay type digital outputs for connecting the load.
• Extendable up to 32 inputs and 16 outputs usingExtension Modules.
• Comfortable alpha-numeric LC display for all steps(logic and set points), functions (timers, counters,time switches and annalogue), inputs, outputs andday-time.
• PC Interface for easy programming, managingmultiple programmes and for simulation. The specialsoftware, Leganza-Soft, enables creating ladderdiagrams, simulation, testing, documentation andprinting.
• With in-built EEPROM memory, programmes andparameters are saved despite accidental powerfailure.
• DIN 35 Rail or optional base mounting for Leganzaand Extension Module.
• Optional EEPROM Memory Card, having samememory as in-built, allows transfer of the programmeand parameters, secured back-up and local storage.
• Optional Extension Module, same size, with LEDdisplay instead of LCD, for extending inputs andoutputs exactly as per the basic Unit, without PCinterface and key pad.
• Compact and standardised [72(4 modular spaces)× 90 × 95 mm] dimensions.
• With mark.
Digital Controllers,Leganza
• Widely used in low cost and simple automation, suchas Auto-Packing Machines, Auto-Printing Machines,Domestic and Commercial Building Controls,Auto-Parking Controls, Home Applications etc.
12
3
8
C1 C2 I3 I5I1 ANI1
I2 I4 I6 ANI2
46
5
7
ALTDEL
Z1 Z2 Z3
Z4
OKESC
Q1 Q2 Q3 Q4
Q1 Q2 Q3 Q4
SUP -SUP +
SPECIFICATIONS
88DDT0 88DDT8 87DDT0 87DDT8
Digital Inputs 6 8Analog Inputs 2 –Supply voltage 12-24V DC 110-240V AC, 50/60HzSupply variation -10% to +10% -20% to +10%Digital input voltage range OFF (“0”): 5V AC max. OFF (“0”): 40V AC max.
ON (“1”): 12V AC min. ON (“1”): 80V AC min.Digital input current 5mA 5mAAnalogue input voltage range 0 to +10V DC –Analogue input Resolution 1 part in 256 –Real Time Clock Present PresentOutputs 4 Relays (electro mechanical) 4 Relays (electro mechanical)Continuous maximum 10A (Resistive load), 10A (Resistive load)current output 240V AC or 28V DC 240V AC or 28V DCIndications, Alpha-numeric LCD, 12 Characters × 4 Lines LCD, 12 Characters × 4 LinesPower consumption ~ 3 W ~ 3 WOperating temperature 0 to +50°C 0 to +50°CStorage temperature 0°C to + 70°C 0°C to + 70°CProtection IP20 IP20Mounting DIN 35 Rail or base DIN 35 Rail or baseMain/Expansion Unit Dim., mm 72 (4 modular spaces)×90×65 72 (4 modular spaces)×90×65PC Interface RS232 C RS232 CLines available for Ladder Diagram 64 lines 250 lines 64 lines 250 lines
SCHEMATIC CONNECTIONS
2
All dimensions in mm
Digital Controllers,Leganza
INPUTS
UP TO 3
EXTENSION MODULE
ADDITIONALOUTPUTS
EXTENSIONMODULE
O/P1 O/P2 O/P3 O/P4
O/P4O/P3O/P2O/P1
51 32 4 76 8
C1 C2 I/P1 I/P3 I/P5 I/P7
NL I/P2 I/P4 I/P8I/P6
ADDITIONALINPUTS
TOSERIALPORT
PC
LEGANZACD
SerialInterface
Cable8GDDT2
MemoryCard
8GDDT3OUTPUTS
Q1 Q2 Q3 Q4
Q4Q3Q2Q1
ESCZ1
Z2Z4
DEL
OKZ3
ALT
C1 C2
L N
I1 I3 I5 I7
I4 I8I6I2
110 - 240VAC
OR
LEDs
1 32 4O/PI/P
SEL ABC
14.3
100.
0 C
/C
90.0
107.
0
Ø4.236.0
72.0
II
Q5
I
Q7
I109
Q6
1211 I
Q8
14I13 1615 II
45.0
65.0
DIN RAIL(35 mm-SYMMETRICAL)
DIMENSIONS
14.3
100.
0 C
/C
90.0
107.
0
Ø4.236.0
72.0
Z1ESC
Z4Z2
Z3OK
DEL ALT
45.0
65.0
DIN RAIL(35 mm-SYMMETRICAL)
Leganza
Extension Module
Digital Controllers,Leganza
3
All dimensions in mm
T T T T15-18R:
S: B1
FRONT DISPLAY
4
Digital Timers, Eliro
SPECIFICATIONS
Cat No. V0DDT0
Nominal 110-240V AC or 24V AC/DCVoltage (Ur) (selectable)
Operating Range -15% to +10% of Ur
Frequency 50/60 Hz
Modes On delay, Cyclic off/on,Cyclic on/off, Signal on/offSignal off Delay, Interval,Signal off/on, One shot output.
Timing h:m m:s hr min sec9:59 9:59 999 999 999
99.9 99.9 99.9
Repeat Accuracy ± 50 ms
Max. Reset Time 100 msec
Max. Switching Rate,at max./min. load 360/1000 per hour
Output Contacts 1 C/O, AgNi 90/10 (Cadmium free)
Output Contact Rating 5A @ 240 V AC / 28 V DC(resistive)
Electrical Life 1 × 105 operations
Mechanical Life 5 × 106 operations
Power Consumption 15 VA
Dimension (WxDxH) 17.5 × 76 × 89 (mm)
Terminal Capacity 2.5 mm² max.
Mounting Base/DIN rail (Sym.35mm)
Weight 85 gms approx (unpacked)
FEATURES
• 8 mode multifunction facility for complete flexibilityand wide range applications.
• Timing from 0.1 second to 999 hours.
• Selectable up/down counting modes to showelapsed/remaining time.
• 3 digit LC display for preset time and run time.
• Wide operating range for supply voltage.
SET ADJ
RELAY STATUSFORLED INDICATION
FUNCTION
RANGE
PRESET TIME
UP/ DN
RUN TIME
H M S
FUNCTIONS
Power Supply Pulse
(A) 1. On Delay : The Timer Starts when both Power (P) &Signal (S) are applied. The relay is energized at the endof Preset Time (T) & remains On till Power is removed.
(B) 2. Cyclic Off/On (Off Star t [Sym, Asym]) : TONand TOFF can be same or different. The relaykeeps on changing its status till the power is removed
(C) 3.Cyclic On/Off (On Start [Sym, Asym]) :This function is quite similar to the function (b)but initially the relay is on for period TON after thepower is applied.
(D) 4. Signal On/Off : The output relay is turned onfor Preset Time (T) whenever the Signal (S) isapplied or removed.
(E) 5. Signal Off Delay : Output relay becomes onwhen Signal (S) is applied. Timer duration (T) startswhen Signal (S) is removed. At the end of Timerduration (T) the output relay goes off. Signal (S), ifapplied during the Timer duration (T) will re-triggerthe Timer and the total duration will be extended.
(F) 6. Interval : When Signal (S) is applied, the Timerstarts and the output relay is energized. The outputrelay becomes off at the end of Timer Duration (T).
(G) 7. Signal Off/On : When Signal (S) is applied orremoved, the relay changes its state after Timerduration (T).
(H) 8. One shot Output : When Signal (S) is applied,the Timer Duration (T) star ts. At the end of TimerDuration (T), the relay gets energized forapproximately 1 Sec.
Notes : P = POWER, S = SIGNAL, R = RELAY.
T TT T15-18R:
S: B1
15-18R:
S:T
B1OFFTON T ON TOFF
P: A1-A2
S:
R:
B1
15-18T
S:
R:
B1
15-18T TT ONOFF OFF T ON
T15-18R:
S: B1
15-18R:
S: B1
T
SEC.T 115-18R:
S: B1
• Easy front settings.
• Tamper-proof with key lock function.
• Confirms to IEC standards for EMI / EMC, with
mark.
• Compact and standard size of 1 module space.
• Optional base or DIN 35 Rail mounting.
100.
0 C
/C
17.5 BASE MOUNTING
67.0
45.0
76.0
89.0
(35
mm
-SY
MM
ET
RIC
AL)
DIN
RA
IL
DIMENSIONS
5
STANDARDS AND CERTIFICATION
Certification
Environmental CE
Temperature Limits Operating -10° to +50°CStorage -20° to +65°C
Humidity 93% Rh
Installation Category II IEC1010 - 1 1990 + 2nd Amendment 1995
Pollution Degree II IEC1010 - 1 1990 + 2nd Amendment 1995
Degree of Protection IP 30 IEC Pub 947 - 1(1998) / IS 13947 Part I 1993
Electromagnetic Compatibility (EMC)
• Vibration F = 10 to 55 Hz, A = 0.35mm or 5gm IS 9000 (Part VIII -1981); IS 9001 (Part XIII -1981)
• Electrostatic Discharge Level III (Air 8KV / Contact 6KV) IEC 1000 - 4 - 2, First Edition 1995 - 01
• Fast Transients Level III 2KV (Peak) Tr / Th = 5 / 50 Rep. Freq. = 5KHz IEC 1000 - 4 - 4, First Edition 1995 - 01
• Surges Level IV Tr / Th = 8/20µs Common Mode : 4KV IEC 1000 - 4 - 5, First Edition 1995 - 02Differential Mode : 2KV
• Voltage Dips 30% reduction / 10 ms, 60% reduction / 100 ms IEC 1000 - 4 - 11, First Edition 1994 - 06• Voltage Interruption >95% reduction / 5000 ms IEC 1000 - 4 - 11, First Edition 1994 - 06
Immunity (EMC)
Port - Enclosure 80 - 1000 MHz 10V / m (unmodulated rms) EN 50082 - 2 : 199580%AM (1KHz)
Port - AC Mains 0.15MHz - 80MHz 10 V/m (unmodulated ms) EN 50082 - 2 : 199580%AM (1KHz)
Radiated (EMC)
Port - Enclosure 30MHz - 230 MHz 30 dBµ V/m Quasi Peak EN 50081 - 2 : 1994Measured at 30 m distance
230MHz - 1000 MHz 37 dBµ V/m Quasi PeakMeasured at 30 m distance
Conducted Emission
Port - AC Mains 0.15MHz - 0.5MHz 79 dBµ V Quasi Peak, 66 dBµ V Average EN 50081 - 2 : 19940.50MHz - 30MHz 73 dBµ V Quasi Peak, 60 dBµ V Average
All dimensions in mm
Overall Dimensions (D×H×W) : 76.0 × 89.0 × 17.5 mm
Digital Timers, Eliro
6
Digital Timer Cum Counter,Excello
TIMER COUNTER
1 Elapsed time Current count
2 Set time Preset value
3 Output status Output status
4 Up/Down counting --
5 Change set time Change Preset value
6 Operating mode 1 or 2 Settingdisplay indication
7 LOCK indication LOCK indication
8 Range indication --
9 LOCK/SET Key LOCK/SET Key
10 RESET Key RESET Key
TIMER SPECIFICATIONS
Modes of A (On Delay), B (Cyclic Off/On),operation C (Cyclic On/Off), D (Signal On/Off),
E (Signal Off Delay), F (Signal Off/On), G (Interval), H (One ShotOutput) [Selectable by DIP switch]
Time range DIP Switch Selectable
H : M : S H : M Hr Min Sec95:59:59 9999:59 99999:9 99999.9 99999.9
Output 1 Instantaneous + 1 Delayed / 2 DelayedRelay [Selectable by DIP switch]
Time count-ing Direction
UP/DOWN Selectable
Indication 7 segment LCD, Elapsed Time 7mm Height Set Time 4.45mm Height
Lock Permanent “KEY LOCK” with DIP Switchor LOCK/UNLOCK with Front panel key
FRONT DISPLAY
LOCK
H: 1SM: 2
9
10
LOCK/SET
RESET
TIMER / COUNTER
8
6
4
5
3
2
1
7
FEATURES
• 48×48 mm format front.
• Option of configurating as either Timer or Counter.
• Easy to read LC display.
• Simple operation.
• Option of screw terminals for wires/lugs or 11 Pinsocket mouting termination.
• Panel mounting
Cat No. Supply Voltage Termination42DFT0 240V AC 50/60 Hz Screw Terminals42DFS0 240V AC 50/60 Hz 11 PIN Socket41DFT0 110V AC 50/60 Hz Screw Terminals41DFS0 110V AC 50/60 Hz 11 PIN Socket45DFT0 24V AC / DC Screw Terminals45DFS0 24V AC / DC 11 PIN Socket
COMMON SPECIFICATIONS
1. Supply Voltage 240V AC, 110V AC, 24V AC/DC2. Supply Variation -15% to +10% of Supply Voltage3. Power Consumption 15 VA4. Indications 7 segment LC display5. Operating temperature -10°C to +50°C6. Storage temperature -20°C to +65°C7. Case material Lexan 143, gray8. Weight 150 gms. nett9. Overall dimensions 105×48×48 mm for socket mtg.
89×48×48 mm for screw term.10. Panel cutout 45×45 mm ± 0.1 mm
COUNTER SPECIFICATIONS
Mode of Addition (UP), Subtraction (DOWN),operation Direction (DIR), Independent (IND), Phase
(PHASE) [Selectable by DIP Switch]Power failurememory method
Battery
Output OUT1 or OUT2 as per Set value1 orvalue 2 respectively, [Selectable by DIPSwitch] as per the diagrams.
Digits -99999 to 999999 (0 to 999999 for setting)Countingspeed (Input 30 Hz/4 kHz [Selectable by DIP Switch]max.frequency)
RANGE
COUNTER OPERATION MODES
1. Input mode(1) For the input mode you can choose one of the following five modes.
7
P :Cyclic OFF/ON
S :(b)
R :
P :Cyclic ON/OFF
S :(C)
R :
P :Signal ON/OFF
S :(d)
R :
P :Signal OFF Delay
S :(E)
R :
P :Interval
S :(F)
R :
P :Signal OFF/ON
S :(G)
R :
P :One Shot
S :(H)
R :
T : PRESET TIME t : PERIOD < T P : POWER S : SIGNAL R : RELAY
P :On Delay
S :(A)
R :T
A1- A2
B1
15-18
T t T
OFFONTOFFT T ONT
T tT TT tTA1- A2
1815
B1
OFFTONT T ON OFFT
T tT TT tT
15-18
A1- A2
B1
B1
15-18
A1- A2
TT T T
T TT tT t
A1- A2
15-18
B1T
T t Tt t
A1- A2
B1
15-18T
T ttT T
15-18
B1
A1- A2
TTT T
T t TT tT tT
SEC.
B1
15-18
A1- A2
1
t t
T
T T T
Digital Timer Cum Counter,Excello
TIMER OPERATION MODES
* Directive DIR
* Independent IND
* Phase PHASE* Addition UP
* Subtraction DOWN
Digital Timer Cum Counter,Excello
8
(2) After the counter has been reset. Setting 2 is displayed in the count-down mode. “Ø” appears instead in allother modes.
Input mode Operation Minimum Input signal width 30 Hz
IN1 or IN2 works as an input * Example where IN1 is the count input an IN2 is the input block (gate).block (gate) for the other input.
Addition
UP
IN1 or IN2 works as an input * Example where IN2 is the count input an IN1 is the input block (gate).block (gate) for the other input.
Subtraction
DOWN
* “A” must be more than the minimum input signal width
IN1 is the count input and IN2 isthe addition or subtraction directiveinput. IN2 adds at L level and
Directive subtracts at H level
DIR
* “A” must be more than the minimum input signal width
IN1 is addition input and IN2 issubstraction input.
Independent
IND
* IN1 and IN2 are completely independent, so there is no restrictionon signal timing
Addition when the IN1 phaseadvances beyond IN2, andsubtraction when the IN2 phase
Phase advances beyond IN1.
PHASE
* “B” must be more than the minimum input signal width
2. Output mode
For the set value 1, you can choose one of the For the set value 2, you can choose one of thefollowing four modes. following eight modes.
* Maintain output/over count I HOLD-B * Maintain output/hold count HOLD-A
* Maintain output/over count II HOLD-C * Maintain output/over count I HOLD-B
* Maintain output/over count III HOLD-D * Maintain output/over count II HOLD-C
Reset
HIN2
Counting (subtraction)
Counting (addition)
L
n
0
IN1 LH
Count Up
n-2
2
n-1
1
n-3
3
AA AA
n-2
3
n-3
0
n
12
n-1
Blocked
-----
-----
Reset
Blocked
Counting (addition)
Counting (subtraction)
IN2
IN1
L
L
H
H
Count Up
n-2
1
n-1
0
n
32
n-3 n-4
4 nn-1
01
A
Blocked
AA A
-----
-----
Reset
IN1
IN2
Counting (addition)
H
H
10
L
L
Subtraction
3
Addition
2
A
24 3
A
10
A
1
A
432
Addition
Reset
IN2
Counting
HL
0 2 31 3 24 21 321
IN1 LH
Phase advance
Reset
0
LIN2
Counting
IN1HL
H
3
B
1
B
2 2
Phase retard
01
Digital Timer Cum Counter,Excello
* One shot/over count SHOT-A * Maintain output/over count III HOLD-D
* Phase PHASE * One shot/over count SHOT-A
* One shot/recount I SHOT-B
* One shot/recount II SHOT-C
* One shot/hold count SHOT-D
* Output mode for set value 1
Output mode Operation * (Example when input mode is either addition or subtraction)
Output control is maintained aftercount-up completion and until
Maintain output resetting However, counting isOver count I possible despite completion of
HOLD-Bcount-up
* n : Set value 1
Output control is maintained aftercount-up completion and until the
Maintain output next signal enters. However,Over count II counting is possible despite
HOLD-Ccompletion of count-up
* n : Set value 1
If the count value is greater than orequal to the preset value when
Maintain output counting up, the control is held. TheOver count III count operation is possible anyway.
HOLD-C
* n : Set value 1
Output control is maintained aftercount-up completion for a fixed time
One shot (approx. 1 sec.) Counting is possibleOver count despite completion of count-up.
SHOT-A
* n : Set value 1
* Output mode for set value 2
Output mode Operation * (Example when input mode is either addition or subtraction)
Output control is maintained aftercount-up completion and until
Maintain output resetting During that time, the countOver count display does not change from that
HOLD-Aat count-up completion.
* n : Set value 2
Output control is maintained aftercount-up completion and until
Maintain output resetting However, counting isOver count I possible despite completion of
HOLD-Bcount-up
* n : Set value 2
9
Output Control 2
Counting (addition)
Counting (subtraction)
Counting able/unable
OFF
Able
n-3
3
n-2
2 1
n-1
ON
Unable
n
0
Counting (subtraction)
Output Control 2
Counting able/unable
Counting (addition)
OFF
2 1 0Able
ON
-2-1
n-2 n-1 n n+2n+1
Counting (subtraction)
Counting able/unable
Output Control 1
Counting (addition)
n+2
OFF
n-2
n-2n-1nn+1Able
ON
n+1nn-1 n+2
Counting (subtraction)
Counting able/unable
Output Control 1
Counting (addition)
n+2
OFF
n-2
n-2n-1nn+1
Able
ON
n+1nn-1 n+2
OFF
Counting (subtraction)
Counting able/unable
Output Control 1(addition)
Counting (addition)
n+2
OFF
n-2
n-2n-1nn+1
ON
n+1nn-1 n+2
OFFOutput Control 2(subtraction)
ON
Able
Counting (subtraction)
Counting able/unable
Output Control 1
Counting (addition)
n+2
OFF
n-2
n-2n-1nn+1
ON
n+1nn-1 n+2
OFF
Approx 1s
Able
Output mode Operation * (Example when input mode is either addition or subtraction)
Output control is maintained aftercount-up completion and until the
Maintain output next signal enters. However,Over count II counting is possible despite
HOLD-Ccompletion of count-up
* n : Set value 2
If the count value is greater than orequal to the present value when
Maintain output counting up the counter startsOver count III counting up again. the count
HOLD-Doperation is possible anyway.
* n : Set value 2
Output control is maintained aftercount-up completion for a fixed time
One shot (approx. 1 sec.) Counting isOver count possible despite completion of
SHOT-Acount-up.
* n : Set value 2
Output control is maintained aftercount-up completion for a fixed
One shot time (approx. 1 sec.) Counting isRecount I possible despite completion of
SHOT-Bcount-up. However, reset occurssimultaneous with completion ofcount-up While output is beingmaintained, restarting of thecount is not possible. * n : Set value 2
Output control is maintained aftercount-up completion for a fixed time
One shot (approx. 1 sec.) Counting is possibleRecount II despite completion of count-up.
SHOT-CHowever, reset occurs simultaneouswith output OFF.
* n : Set value 2
Output control is maintained aftercount-up completion for a fixed time
One shot (approx. 1 sec.) During that time,Hold count the count display does not change
SHOT-Dfrom that at count-up completion,Reset occurs simultaneous withoutput OFF.
* n : Set value 2
OFF
Counting (subtraction)
Output Control 2
Counting able/unable
Counting (addition)
OFF
2 1 0Able
ON
-2-1
n-2 n-1 n n+2n+1
Output Control 2(subtraction)
OFFON
Counting (subtraction)
Output Control 2(addition)
Counting able/unable
Counting (addition)
OFF
2 1 0Able
ON
-2-1
n-2 n-1 n n+2n+1
OFF
Approx 1s
Counting (subtraction)
Output Control 2
Counting able/unable
Counting (addition)
OFF
2 1 0Able
ON
-2-1
n-2 n-1 n n+2n+1
OFF
Reset'(automatic)
Approx 1s
Counting (subtraction)
Output Control 2
Counting able/unable
Counting (addition)
OFF
2 1 0
Able
ON
-2-1
n-2 n-1 n n+2n+1
OFF
Reset(automatic)
Approx 1s
Counting (subtraction)
Output Control 2
Counting able/unable
Counting (addition)
OFF
1 0 -1
Able
ON
n-1n
n-1 n n+1 10
OFF
Reset(automatic)
Approx 1s
Counting (subtraction)
Output Control 2
Counting able/unable
Counting (addition)
OFF
1 0
UnableON
n-1n
n-1 n 10
AbleAble
Digital Timer Cum Counter,Excello
10
Output mode for set value 1
HOLD-C HOLD-D HOLD-B SHOT-A
SHOT-AAs usual As usual
(this combination unchanged) (this combination unchanged)
Output mode SHOT-B
for set value 2
SHOT-C
SHOT-D
Note : When control output 1 is on, the output mode of setting 2 (SHOT - A, B, C, D) is also on and output 1 changes as shown in the above table.
DIMENSIONS
11 PIN, SOCKET MOUNTING TERMINATION
SCREW TERMINATION
Output 2
Output 1
Approx.1s Output 2
Output 1
Approx.1s
Approx.1s
Output 2
Output 1
48.0
SQ
5.5GRID RING
Transparent Cover
105.0 max.
89.0
H:M:SLOCK
1 255.0
LCD
55.0
LCD
M:H:LOCK
2S 1
48.0
SQ
89.0
GRID RING
Transparent Cover
5.5
Weight : 150 gms (Unpacked)Case Material : Lexan 143 grayRecommendedPanel Cutout : 45.0mm × 45.0mm ±0.1Overall Dimensions : 105.0 × 48.0 × 48.0
Weight : 150 gms (Unpacked)Case Material : Lexan 143 grayRecommendedPanel Cutout : 45.0mm × 45.0mm ±0.1Overall Dimensions : 89.0 × 48.0 × 48.0
All dimensions in mm
Digital Timer Cum Counter,Excello
11
ROUND BEZEL
SPECIFICATIONS
Item Counters Hour Meter
1.Range 999999 99999.9 Hrs
2.Display 6 Digit LCD, 5 mm. height 6 Digit LCD, 5 mm. height
3.Resolution 1 count 0.1 hrs4.Accuracy ± 1 count at 25°C ±0.2% at 25°C
5.Temperature - 10°C to +50°C (Operating), - 10°C to +50°C (Operating),- 20°C to +65°C (Storage) - 20°C to +65°C (Storage)
6.Humidity 95% Rh (Non-condensing) 95% Rh (Non-condensing)
7.ProtectionIP54 (For front side only) IP54 (For front side only)class
8.Terminals 1, 2 : Input Supply 3 : Count Input 1, 2 : Input Supply 3 : Enable Input4 : Reset 4 : Reset
FEATURES
• Easy to read 6-digit LCD.
• Exceptional reliability with in-built nonvolatilememory (EEPROM) retaining data for 100 years.
• Wide range of supply voltage.
• “Electrical Reset” terminal for Counters and HourMeters and “Enable” terminal for Hour Meters.
• Available in 3 different Bezels.
• Low power consumption.
24×48 BEZEL SCREW MOUNT BEZEL
Digital Hour Meters & Counters
Cat.Ref. ZA2FBx* ZB2FBx* ZC2FBx* ZA1FBx* ZB1FBx* ZC1FBx*Input
9-32V AC/DC 75-130V AC 190-270V AC 9-32V AC/DC 75-130V AC 190-270V ACVoltageMax. Supply 4mA@24VAC
4mA@110VAC 4mA@240VAC3mA@24VAC
3mA@110VAC 3mA@240VACCurrent 4mA@24VDC 3mA@24VDCCounting
2Hz (Max) —Frequency
* x = A / B / C, where A : Round Bezel, B : 24 × 48 Bezel, C : Screw Mount Bezel
12
Digital Hour Meters & Counters
DIMENSIONS
ROUND BEZEL
24 × 48 BEZEL
SCREW MOUNT BEZEL
Product improvement is a continuous process.Hence data given in this catalogue is subject to change without intimation.
4
1 2
3
47.3 SQ.±0.2
C/C
Ø4.5(2X)
+0.2 Thumb Nut 4 mm
2.04.0
27.5
42.5
Black Bezel
58.4
LCD
37.0 mm x 24.6 mm
Recommended Panel Cutout :
+0.5 +0.5
'U' Clamp
44.6
1
4
2
3
36.5
20.0
22.1
2.0
Thumb Nut 4 mm
24.0
48.0
Black Bezel LCD
45.5 mm x 23.0 mm
Recommended Panel Cutout :+0.5 +0.5
'U' Clamp
Black Bezel
31.1
35.5
LCD
26.5
37.0 mm x 24.6 mm
Recommended Panel Cutout :+0.5 +0.5
'U' Clamp
(2X)Ø
4.5
3
44.5
53.0
4
36.1
C/C±0.2
+0.2
1 2
23.5
2.0
1.5
Thumb Nut 4 mm 36.5
All dimensions in mm
13
CONNECTIONS
DIGITAL HOUR METER DIGITAL COUNTER
DIGICON
CG InternationalInternational Operations ofCrompton Greaves Limited‘Jagruti’, Kanjurmarg (East),Mumbai (Bombay) - 400 042.(INDIA)Telephones : +91-22-2578 2451Direct : +91-22-2577 6524/6649Fax : +91-22-2577 4066Email : cgi @ cgl.co.inHome Page : http://www.cglonline.com/international/
CG
.ID/55/D
igicon/3/03
top related