conformance test experiments for distributed real-time systems

Conformance Test Experiments for Distributed Real-Time SystemsRachel Cardell-Oliver

Complex Systems GroupDepartment of Computer Science & Software EngineeringThe University of Western Australia

July 2002

Talk OverviewResearch Goal:

to build correct distributed real-time systems

1. Distributed Real-Time Systems2. Correctness: Formal Methods & Testing3. Experiments: A New Test Method

1. Distributed Real-Time Systems

Real Time Reactions

Distributed

System Characteristics React or interact with their environment Must respond to events within fixed time Distributed over two or more processors Fixed network topology Each processor runs a set of tasks Processors embedded in other systems Built with limited HW & SW resources

Testing Issues for these Systems Many sources of non-determinism

2 or more processors with independent clocks Set of tasks scheduled on each processor Independent but concurrent subsystems Inputs from uncontrolled environment e.g. people Limited resources affects test control e.g. speed

Our goal: to develop robust test specification and execution methods

2. Correctness: Formal Methods & Testing

Goal: Building Correct Systems

Design (intended behaviour)

Implementation

behaves like this?

Software Tests

are experiments designed to answer the question “does this implementation behave as intended?”

Defect tests are tests which try to try to force the implementation NOT to behave as intended

Our focus is to specify and execute robust defect tests

Related Work on Test Case Generation

Chow TSE 1978 deterministic Mealy FSM Clarke & Lee 1997 timed requirements

graphs Neilsen TACAS 2000 event recording automata Cardell-Oliver FACJ 2000 Uppaal timed automata

Specific experiments are described by a test case: a timed sequence of inputs and outputs

Non-determinism is not handled well (if at all) Not robust enough for our purposes

3. Experiments:A New Test Method

Our Method for Defect Testing

1. Identify types of behaviour which are likely to uncover implementation defects (e.g. extreme cases)

2. Describe these behaviours using a formal specification language

3. Translate the formal test specification into a test program to run on a test driver

4. Connect the test driver to the system under test and execute the test program

5. Analyse test results (on-the-fly or off-line)

Example System to Test

Step 1 – Identify interesting behavioursUsually extreme behaviours such as

Inputs at the maximum allowable rate Maximum response time to events

Timely scheduling of tasks

Example Property to Test

Whenever the light level changes from low to high

then the valve starts to openwithin 60csassuming the light level alternates between

high and low every 100cs

Step 2 – choose a formal specification language

which is able to model real-time clocks persistent data concurrency and communication

use Uppaal Timed Automata (UTA)

Example UTA for timely response

m:=0

m:=0

Writing Robust Tests with UTA Test cases specify all valid test inputs

no need to test outside these bounds Test cases specify all expected test outputs

if an output doesn’t match then it’s wrong No need to model the implementation

explicitly Test cases may be concurrent programs Test cases are executed multiple times

Step 3. Translate Spec to Exec UTA specs are already program-like Identify test inputs and how they will be

controlled by the driver Identify test outputs and how they will be

observed by the driver then straightforward translation into NQC

(not quite C) programs

Example NQC for timely responsetask dolightinput() {while (i<=MAXRUNS) {

Wait(100);setlighthigh(OUT_C); setlighthigh(OUT_A); record(FastTimer(0),HIGH-LIGHT); i++;Wait(100);setlightlow(OUT_C); setlightlow(OUT_A); record(FastTimer(0),LOW-LIGHT); i++;

}// end while}// end task

task monitormessages() {while (i<=MAXRUNS) {monitor (EVENT_MASK(1)) {

Wait(LONGINTERVAL);}catch (EVENT_MASK(1)) {

record(FastTimer(0), Message());

i++;ClearMessage();

}} // end while} // end task

Step 4 –test driver

Step 4 - connect tester and execute tests

Step 5: Analyse Results

0

10

20

30

40

50

60

70

1 5 9 13 17 21 25 29 33 37 41 45 49 53 57 61 65 69 73 77 81 85 89 93 97 101

105

109

113

117

121

125

129

Test Point Number

Res

pons

e Ti

me

of V

alve

to H

igh

Ligh

t (cs

)

0

1

2

3

4

5

6

7

8

6 8 34 43 61 62 75 84 91 109 122 124 142 155 164 175 181 187 199 203 207 218 240 248

Task Completion Time (cs)

Task

Iden

tifie

r

p1,s1 p1,a p1,s2 p1,d p2,vm p2,cm p2,cc

Scheduling Deadlines Test Results

Concluding Observations Defect testing requires active test drivers

able to control extreme inputs and observe relevant outputs

Test generation methods must take into account the constraints of executing test cases Robust to non-determinism in the SUT Measure what can be measured

Engineers must design for testability

Results 1:Observation Issues

Things you can’t seeProbe effectClock skewTester speed

Things you can’t see

Motor outputs can’t be observed directly because of power drain so we used IR messages to signal motor

changes But we can observe

touch & light sensors via piggybacked wires broadcast IR messages

The probe effect

We can instrument program code to observe program variables

but the time taken to record results disturbs the timing of the system under test

Solutions observe only externally visible outputs design for testability: allow for probe effects

Clock Skew

Clocks may differ for local results from two or more processors

Solutions: user observations timed only by the tester including tester events gives a partial order

Tester speed

Tester must be sufficiently fast to observe and record all interesting events

Beware scheduling and monitoring overheads execution time variability

Solution: use NQC parallel tasks and off-line analysis for speed

Results 2:Input Control Issues

Input value controlInput timing control

Input Values can be Controlled

Touch sensor input (0..1) good by piggybacked wire

Light sensor input (0..100) OK by piggybacked wire

Broadcast IR Messages good from tester

Also use inputs directly from the env. natural light or button pushed by hand

Input Timing Control is hard to control

Can’t control input timing precisely e.g. offered just before SUT task is called

Solution: Run tests multiple times and analyse average and spread of results

Can’t predict all system timings for a fully accurate model c.f. WCET research, but our problem is harder

Conclusions from Experiments Defect testing requires active test drivers

able to control extreme inputs and observe relevant outputs

Test generation methods must take into account the constraints of executing test cases Robust to non-determinism in the SUT Measure what can be measured

Engineers must design for testability