combustion analyzer xdi-cax 2-12ch, can-output - xtreme-di info@xtreme-di.com 2-12ch, can-output...

Combustion Analyzer XDI-CAx

www.Xtreme-DI.com info@xtreme-di.com

2-12ch, CAN-output

This combustion analyzer has specifically been

designed for engine control and dyno monitoring

applications. The design incorporates a data

acquisition board with 8 high resolution inputs for

pressure transducers or other inputs and 3 inputs

for trigger signals (crankshaft hall, crankshaft VR,

camshaft or encoder), all in a robust machined

aluminum enclosure with mil-spec Deutsch ASU

connectors. This robust design makes it resistant

to vibration and high-temperatures. It features real-

time dynamic pressure measurement of

combustion or port pressure in spark-ignition or

compression ignition engines.

The analysis SW runs on every MS-Windows

based PC or Tablet. For mobile use a pre-

configured 10” Tablet is available on request.

The cycle based pre-processed characteristics

can be sent on CAN-bus in real time to be post-

processed in another ECU or recorded on a

datalogger together with your engine and dyno

data. Additional CAN-HW is necessary.

Application

Speed Sensor Inputs: 3 Inputs, shared Ground for hall type VR sensors optional with integrated conditioner board 3600ppm encoder recommended

Transducer Inputs: up to 12 Inputs, ±10V, pre-configured for XDI-CPS

Acquisition Rate: 100kHz per channel 1000kHz in single channel operation

Sensor Type: Optimized for Fibre-Optic sensor type

Mechanical Data

Housing Material: 3mm billet Aluminum 3D printed ABS-plastic

Housing Temperature Range: 0°C to 60°C

ADC Resolution: 16bit

Timing resolution: 10ns

Weight: 730g

CAN-Output: Kvaser

Some of the signals that can be analyzed:

Peak Pressure and Angle of Peak Pressure

Knock Peak Pressure, Knock Index (based on Cyl. Pressure or based on Knock Sensor, or both)

IMEP, indicated Torque & Power per cylinder

CA50, Heat Release Rate, COV etc.

Actual Start of Injection (e.g. Current Probe on Injector)

Actual Ignition Timing (e.g. Current Probe on Coil Supply)

Intake / Exhaust Port Press. (e.g. Reversion, Scavenging)

Actual Fuel Pressure during Injection (Pulsations)

Combustion Analyzer XDI-CAx

www.Xtreme-DI.com info@xtreme-di.com

Electrical Data

Pressure Input Signal: -10 to +10 V

Optimized for Optrand Sensors, 0-5V

Trigger Input Signal: -10 to +10 V

VR optional with integrated conditioner board

Power Supply Voltage: 11 to 30 VDC, 30 W

regular wall-outlet power supply with ASU connector is part of the kit

Current Draw: 2.7A Max

Connectors and Wires

CRK-Connector VR ASU03SD

CAM / CRK-Connector ASU03SA

Sensor Connectors ASU03SN

integrated +5V supply, 1A total for all channels 12 sensor supply on request

USB Connectivity: ASU05SB

Power Supply: ASU03SC

Application Hint

For correct setup of sensors and software please refer to manual and HowTo videos.

For transducer data please refer to the calibration sheet. XDI sensors can also be custom calibrated following the calibration manual.

Please find further application hints at http://www.xtreme-di.com/index_files/XDI_CA8.htm

Pricing

XDI-CA2 rp / billet $4,500 / $4,900

XDI-CA4 rp / billet $5,500 / $5,900

XDI-CA8 rp / billet $8,800 / $9,500

XDI-CA10 rp / billet $9,900 / $10,600

XDI-CA12 rp / billet $10,900 / $11,700