chmod unix
Post on 05-Apr-2018
216 Views
Preview:
TRANSCRIPT
-
7/31/2019 Chmod Unix
1/3
In Unix, how do I change the permissions for a file?
You can change file permissions with the chmod command. In Unix, file permissions, which establish who may have
different types of access to a file, are specified by both access classes and access types. Access classes aregroups of users, and each may be assigned specific access types. The access classes are "user", "group", "other",
and "all". These refer, respectively, to the user who owns the file, a specific group of users, the other remaining
users who are not in the group, and all three sets of users. Access types (read, write, and execute) determine what
may be done with the file by each access class.
There are two basic ways of using chmod to change file permissions:
Symbolic method
The first and probably easiest way is the relative (or symbolic) method, which lets you specify access classes and
types with single letter abbreviations. A chmod command with this form of syntax consists of at least three parts
from the following lists:
Access Class Operator Access Type
u (user) + (add access) r (read)
g (group) - (remove access) w (write)
o (other) = (set exact access) x (execute)
a (all: u, g, and o)
For example, to add permission for everyone to read a file in the current directory namedmyfile, at the Unix
prompt, you would enter:
chmod a+r myfile
The a stands for "all", the + for "add", and the r for "read".
Note: This assumes that everyone already has access to the directory where myfile is located and its parent
directories; that is, you must set the directory permissions separately.
If you omit the access class, it's assumed to be all, so you could also enter the previous example as:
chmod +r myfile
You can also specify multiple classes and types with a single command. For example, to remove read and write
permission for group and other users (leaving only yourself with read and write permission) on a file namedmyfile,
you would enter:
chmod go-rw myfile
You can also specify that different permissions be added and removed in the same command. For example, to
remove write permission and add execute for all users onmyfile, you would enter:
chmod a-w+x myfile
In each of these examples, the access types that aren't specified are unchanged. The previous command, for
example, doesn't change any existing settings specifying whether users besides yourself may have read ( r )
access to myfile. You could also use the exact form to explicitly state that group and other users' access is set
only to read with the = operator:
chmod go=r myfile
The chmod command also operates on directories. For example, to remove write permission for other users on a
subdirectory named mydir, you would enter:
chmod o-w mydir
nix, how do I change the permissions for a file? - Knowledge Base http://kb.iu.edu/data/abdb.html
3 01-09-2011 PM 06:48
-
7/31/2019 Chmod Unix
2/3
To do the same for the current directory, you would enter:
chmod o-w
Be careful when setting the permissions of directories, particularly your home directory; you don't want to lock
yourself out by removing your own access. Also, you must have execute permission on a directory to switch ( cd )
to it.
Absolute form
The other way to use the chmod command is the absolute form. In this case, you specify a set of three numbers that
together determine all the access classes and types. Rather than being able to change only particular attributes, you
must specify the entire state of the file's permissions.
The three numbers are specified in the order: user (or owner), group, other. Each number is the sum of values that
specify read (4), write (2), and execute (1) access, with 0 (zero) meaning no access. For example, if you wanted to
give yourself read, write, and execute permissions onmyfile; give users in your group read and execute
permissions; and give others only execute permission, the appropriate number would be calculated as (4+2+1)
(4+0+1)(0+0+1) for the three digits 751. You would then enter the command as:
chmod 751 myfile
As another example, to give only yourself read, write, and execute permission on the current directory, you wouldcalculate the digits as (4+2+1)(0+0+0)(0+0+0) for the sequence 700, and enter the command:
chmod 700
If it seems clearer to you, you can also think of the three digit sequence as the sum of attributes you select from the
following table:
400 Read by owner
200 Write by owner
100 Execute by owner
040 Read by group
020 Write by group
010 Execute by group
004 Read by others
002 Write by others
001 Execute by others
To create an access mode, sum all the accesses you wish to permit. For example, to give read privileges to all, andwrite and execute privileges to the owner only for a file, you would sum: 400+200+100+040+004 = 744. Then, at the
Unix prompt, you would enter:
chmod 744 myfile.ext
Some other frequently used examples are:
777 anyone can do anything (read, write, or execute)
755 you can do anything; others can only read and execute
711 you can do anything; others can only execute
644 you can read and write; others can only read
More information
For more information about chmod, consult the manual page. At the Unix prompt, enter:
nix, how do I change the permissions for a file? - Knowledge Base http://kb.iu.edu/data/abdb.html
3 01-09-2011 PM 06:48
-
7/31/2019 Chmod Unix
3/3
man chmod
At Indiana University, for personal or departmental Linux or Unix systems support , seeAt IU, how do I get support
for Linux or Unix?
This is documentabdb in domain all.
Last modified on June 09, 2011.
Copyright 2005-2010, The Trustees of Indiana University
nix, how do I change the permissions for a file? - Knowledge Base http://kb.iu.edu/data/abdb.html
3 01 09 2011 PM 06:48
top related