cache memory

Cache Memory

3. System Bus

3.1. Computer Components :

MAR

MBR

I/O AR

I/O BR

CPU Memory

I/O Module

Buffers

0

1

2

n

InstructionInstruction

Instruction

...

...DataData

Data

IR

PC

Weaknesses of Main Memory technology

• The access time is relatively (very) slow compared to CPU access time

• CPU has to wait for so many cycles before the information from memory (READ) could arrive in CPU (CPU generally 40 to 50 times faster than main memory)

Why Cache?

• Small “chunk” of memory with “very fast” cycle time (possibly 8-10 times faster than main memory cycle time)

• Holds “the most needed” information (by the CPU)• It is expected that, more than 80% of CPU access

will go to cache, instead of main memory• Overall access time from memory will be faster

Processor-Memory connection: The Cache Memory

ALU1 ALU2

ALU3

ADDER

BUS

R1

R2

R3

ControlUnit

PC

MBR

MAR

IR

CacheMemory

(256-2048 KB)

MainMemory

(0.5-4GB)

40-60 nanosecondcycle time

5-10 nanosecondcycle time

Faster access to/fromcache memory, reduces CPU wait time.Smaller Cache size, lead to problems

Cache Memory: What are going to talk about ?

• We are not discussing the technology• But we are going the discuss about the reason behind

cache implementation :minimizing the CPU idle time

• Also, we are going to discuss about cache :mapping algorithmsreplacement algorithms

Memory Hierarchy - Diagram

Hierarchy ListFrom fastest to slowest access time :

• Registers• L1 Cache• L2 Cache• Main memory• Disk cache• Disk• Optical• Tape

Locality of Reference principlesProgram execution behavior :• During the course of the execution of a program, memory

references tend to cluster• What is a program :

“a set instructions to command the computer to work, to perform something”

loop MOV R1,AADD R2,R1…..

ADD A,R5DEC R3BNZ loop……

Cache• Small amount of fast memory• Sits between normal main memory and CPU• May be located on CPU chip or module• To store temporarily, the most wanted

program/instruction to be executed (by the CPU)

Loop MOV R1,AADD R2,R1……….DEC R3MPY A,R3BNZ loop……

So you want fast?• It is possible to build a computer which

uses only static RAM (see later)• This would be very fast• This would need no cache• This would cost a very large amount

Cache operation - overview

• CPU requests contents of a memory location

• Check cache memory for this data• If present, get from cache (fast)• If not present, read required block

from main memory to cache• Then deliver from cache to CPU• Cache includes tags to identify which

block of main memory is in each cache slot

Cache Design parameters• Size, how big is the size

(cost and effectiveness)• Mapping Function

(how do we place data in cache)• Replacement Algorithm

(how do we replace data in cache by new data)• Write Policy

(how do we update data in cache)• Block Size

(reflects the access unit of data in cache)• Number of Caches

(how many level oc caches we need : L2 or L3?)

Size does matter• Cost

—More cache is expensive(since cache memory is made of static RAM)

• Speed—More cache is faster (up to a point)—Checking cache for data takes time

(correlated to mapping function)

Typical Cache Organization - continued

Cache Mapping

• Direct• Associative• Set Associative

0

m

2m

3m

4m

5m

6m

Main Memory

CacheLine Number Tag 0 1 2

(C-1)

Block (K words)

Block Length( K words)

Cache Mapping : Direct

Direct Mapping Cache Line Table

• Cache line Main Memory blocks held

• 0 0, m, 2m, 3m…2s-m• 1 1,m+1, 2m+1…2s-m+1

• m-1 m-1, 2m-1, 3m-1…2s-1

Direct Mapping Pros & Cons

• Simple• Inexpensive• Fixed location for given block

—If a program accesses 2 blocks that map to the same line repeatedly, cache misses are very high

Associative Mapping

• A main memory block can load into any line of cache

• Cache searching gets expensive

Cache Mapping :Fully Associative

Set Associative Mapping

• Cache is divided into a number of sets• Each set contains a number of lines• A given block maps to any line in a given

set—e.g. Block B can be in any line of set i

• e.g. 2 lines per set—2 way associative mapping—A given block can be in one of 2 lines in only

one set

Cache Mapping :Set Associative (2 way)

Replacement Algorithms (2)Associative & Set Associative

• Hardware implemented algorithm (speed)• Least Recently used (LRU)• e.g. in 2 way set associative

—Which of the 2 block is lru?• First in first out (FIFO)

—replace block that has been in cache longest• Least frequently used

—replace block which has had fewest hits• Random

Write Policy

• Write through• Write back

Write through

• All writes go to main memory as well as cache

• Multiple CPUs can monitor main memory traffic to keep local (to CPU) cache up to date

• Lots of traffic• Slows down writes• Remember bogus write through caches!

Write back

• Updates initially made in cache only• Update bit for cache slot is set when

update occurs• If block is to be replaced, write to main

memory only if update bit is set• N.B. 15% of memory references are writes

Replacement Algorithms1. FIFO : First In First Out2. LIFO : Last In First Out3. LRU : Least Recently Used

Comparison of Cache Sizes