automatic transaxle (service) [gf4ax-el]
Post on 17-Aug-2015
401 Views
Preview:
DESCRIPTION
TRANSCRIPT
AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B4105BEARING COVER COMPONENT ASSEMBLY [GF4AX-EL]ezf051719205102Assembly Procedure1. Apply ATF to the new O-ring and install it to the bearing cover.O-ring inner diameter85.1 mm {3.35 in}2. Press the new bearing race into the bearing cover.3. Press the new oil seal into the bearing cover using the SST.End Of Siecontrol valve bodyCONTROL VALVE BODY DISASSEMBLY [GF4AX-EL]ezf051721100142Caution Denting or scratching these components will reduce the ability of the transaxle to shift properly. When handling these components or the valve body that contains them, be careful not to drop or hit them.1. Disassemble in the order indicated in the table.2. Neatly arrange the removed parts to avoid confusing the similar parts.Warning Using compressed air can cause dirt and other particles to fly out, causing injury to the eyes. Wear protective eye wear whenever using compressed air.w6u517adrw6u517ads05-17B42AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]3. Clean the removed parts with cleaning solvent, then use compressed air to dry them. Use compressed air to clean out all holes and passages..ymu517aa91 TFT sensor2 Pressure control solenoid valve3 3-2 timing solenoid valve4 Shift solenoid A5 TCC control solenoid valve6 Front control valve body7 Front/premain front gasket8 Premain separator plate9 Front/premain rear gasket10 Rubber balls11 Premain control valve body12 Jet orifice and nut13 Rubber ball14 Oil strainerAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B4305Disassembly Procedure1. Remove the TFT sensor.2. Remove the pressure control solenoid valve, 3-2 timing solenoid valve, shift solenoid A and TCC control solenoid valves.3. Remove the O-rings from the solenoid valves.4. Remove the bolts indicated by the arrows, then remove the front control valve body and premain separator plate and gaskets.5. Remove the front/premain gaskets and separator plate from the front control valve body.6. Remove the rubber ball from the front control valve body.7. Remove the rubber ball from the premain control valve body.8. Remove the bolts, the premain control valve body and the main separator plate and gaskets.9. Remove the premain/main gaskets and separator from the premain control valve body.10. Remove the jet orifice and nut from the main separator plate.11. Remove the rubber balls and oil strainer from the premain control valve body.12. Remove the rubber balls and oil strainer from the main control valve body.13. Turn the assembly over and remove the oil pipe, baffle plate, shift solenoid B and shift solenoid C.15 Premain/main front gasket16 Main separator plate17 Premain/main rear gasket18 Rubber balls19 Oil strainer20 Oil pipe component21 Oil baffle22 Shift solenoid B23 Shift solenoid C24 Rear control valve body25 Main/rear rear gasket26 Rear separator plate27 Main/rear front gasket28 Rubber balls29 Oil strainers30 Rubber balls31 Oil strainers32 Main control valve bodyymu517aaaw6u517advw6u517adww6u517ady05-17B44AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]14. Remove the bolts shown in the figure and remove the rear separator plate and gaskets.15. Remove the main/rear gaskets and separator from the rear control valve body.16. Remove the rubber balls and oil strainers from the rear control valve body.17. Remove the rubber balls and oil strainers from the main control valve body.End Of SiePREMAIN CONTROL VALVE BODY DISASSEMBLY [GF4AX-EL]ezf051721100143Caution Denting or scratching these precisely machined components will reduce the ability of the transaxle to shift properly. When handling these components or the valve body that contains them, be careful not to drop or hit them. Using a magnet in this procedure could magnetize the valve body inner components, reducing the ability of the transaxle to shift properly. Do not use magnets or magnetized tools when carrying out maintenance on these components.Note If a valve does not slide out under its own weight, place the valve body open-side down and tap on the valve body lightly with a plastic hammer.1. Disassemble in the order indicated in the table.Warning Using compressed air can cause dirt and other particles to fly out, causing injury to the eyes. Wear protective eye wear whenever using compressed air.w6u517adzAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B45052. Clean all parts and holes using compressed air and apply ATF to them immediately before assembly..End Of Siexme5614a0251 Spring retainer2 Pressure modifier accumulator spring3 Pressure modifier accumulator valve4 Stop pin5 Stop plug6 3-2 timing valve7 3-2 timing spring8 Stop pin9 Stop plug10 Cut back valve A11 Cut back valve B12 Cut back spring13 Stop pin14 Stop plug15 Bypass valve16 Bypass spring17 Bolts18 1-2 accumulator plate19 1-2 accumulator gasket20 Small 1-2 accumulator spring21 Large 1-2 accumulator spring22 1-2 accumulator piston23 Bolts24 N-R accumulator plate25 N-R accumulator gasket26 N-D accumulator spring27 N-D accumulator piston28 N-R accumulator piston29 Large N-R accumulator spring30 Small N-R accumulator spring31 Premain control valve body05-17B46AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]PREMAIN CONTROL VALVE BODY INSPECTION [GF4AX-EL]ezf051721100144Spring Inspection1. Measure the spring free length. If not within specifications, replace the spring.SpecificationsEnd Of SiePREMAIN CONTROL VALVE BODY ASSEMBLY [GF4AX-EL]ezf051721100145Assembly Procedure1. Apply ATF to the seal rings.2. Install the piston and N-D accumulator spring.3. Apply ATF to the seal rings.4. Install the N-R accumulator springs and piston.5. Install the N-R accumulator gasket and plate.6. Tighten the plate bolt.Tightening torque6.57.8 Nm {6680 kgfcm, 5869 inlbf}7. Apply ATF to the seal rings.8. Install the piston and 1-2 accumulator springs.9. Install the 1-2 accumulator gasket and plate.10. Tighten the plate bolt.Tightening torque6.57.8 Nm {6680 kgfcm, 5869 inlbf}11. Install the bypass valve spring, bypass valve, stop plug, and stop pin.12. Install the cut back spring, cut back valve B, cut back valve A, stop plug, and stop pin.13. Install the 3-2 timing spring, 3-2 timing valve, stop plug, and stop pin.14. Install the pressure modifier accumulator valve, pressure modifier accumulator spring, and spring retainer.End Of SieSpringOuter diameter (mm {in})Free length (mm {in})No. of coilsWire diameter (mm {in})Pressure modifier accumulator spring 8.2 {0.32} 38.2 {1.50} 16.5 1.2 {0.047}3-2 timing spring 8.25 {0.325} 35.4 {1.394} 12.5 0.85 {0.033}Cut back spring 8.2 {0.32} 29.8 {1.17} 7.4 0.6 {0.02}Bypass spring 6.3 {0.25} 29.5 {1.16} 11.7 0.6 {0.02}Small 1-2 accumulator spring 14.8 {0.583} 81.6 {3.21} 17.7 1.7 {0.067}Large 1-2 accumulator spring 20.2 {0.795} 81.6 {3.21} 12.5 2.3 {0.091}N-D accumulator spring 9.8 {0.39} 52.9 {2.08} 12.0 1.0 {0.039}Small N-R accumulator spring 7.2 {0.28} 60.1 {2.37} 26.2 1.0 {0.039}Large N-R accumulator spring 11.2 {0.441} 56.0 {2.20} 15.2 1.6 {0.063}w6u517ae1w6u517ae2w6u517ae3AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B4705MAIN CONTROL VALVE BODY DISASSEMBLY [GF4AX-EL]ezf051721100146Caution Denting or scratching these precisely machined components will reduce the ability or the transaxle to shift properly. When handling these components or the valve body that contains them, be careful not to drop or hit them. Using a magnet in this procedure could magnetize the valve body inner components, reducing the ability of the transaxle to shift properly. Do not use magnets or magnetized tools when carrying out maintenance on these components.Note If a valve does not slide out under its weight, place the valve body open-side and tap on the valve body lightly with a plastic hammer.1. Disassemble in the order indicated in the table.Warning Using compressed air can cause dirt and other particles to fly out, causing injury to the eyes. Wear protective eye wear whenever using compressed air.2. Clean all parts and holes using compressed air and apply ATF to them immediately before assembly..w6u517ae41 Spring retainer2 Converter relief spring3 Converter relief valve4 Stop pin5 Stop plug6 Solenoid reducing spring7 Solenoid reducing valve8 Spring retainer9 Low reducing spring10 Low reducing valve11 Stop pin12 Stop plug13 1-2 shift valve14 1-2 shift spring15 Stop pin16 Stop plug17 2-3 shift valve18 2-3 shift spring19 Stop pin20 Stop plug21 Coast timing spring22 Coast timing valve23 Stop pin24 Stop plug25 TCC shift valve26 TCC shift spring27 Stop pin28 Stop plug05-17B48AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]End Of SieMAIN CONTROL VALVE BODY INSPECTION [GF4AX-EL]ezf051721100147Spring Inspection1. Measure the spring free length. If not within the specifications, replace the spring.SpecificationsEnd Of SieMAIN CONTROL VALVE BODY ASSEMBLY [GF4AX-EL]ezf051721100148Assembly Procedure1. Install the 3-4 shift spring, 3-4 shift valve, stop plug, and stop pin.2. Install the TCC shift spring, TCC shift valve, stop plug, and stop pin.3. Install the coast timing valve, coast timing spring, stop plug, and stop pin.29 3-4 shift valve30 3-4 shift spring31 Stop pin32 Stop plug33 Pressure modifier spring34 Pressure modifier valve35 Main control valve bodySpringOuter diameter (mm {in})Free length (mm {in})No. of coilsWire diameter (mm {in})Converter relief spring 7.4 {0.29} 32.3 {1.27} 13.5 1.1 {0.043}Solenoid reducing spring 8.0 {0.31} 39.7 {1.56} 12.0 0.9 {0.03}Low reducing spring 8.7 {0.34} 38.3 {1.51} 12.5 0.9 {0.03}1-2 shift spring 7.4 {0.29} 36.6 {1.44} 12.0 0.8 {0.031}2-3 shift spring 7.4 {0.29} 36.6 {1.44} 12.0 0.8 {0.031}Coast timing spring 6.2 {0.24} 28.0 {1.10} 16.0 0.6 {0.02}TCC shift spring 6.0 {0.24} 40.0 {1.57} 13.8 0.5 {0.02}3-4 shift spring 7.4 {0.29} 36.6 {1.44} 12.0 0.8 {0.031}Pressure modifier spring 5.0 {0.2} 19.0 {0.75} 12.7 0.6 {0.024}w6u517ae5w6u517ae6AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B49054. Install the 1-2 shift spring, 1-2 shift valve, stop plug, and stop pin.5. Install the 2-3 shift spring, 2-3 shift valve, stop plug, and stop pin.6. Install the low reducing valve, low reducing spring, and spring retainer.7. Install the solenoid reducing valve, spring, stop plug, and stop pin.8. Install the converter relief valve, converter relief spring, and spring retainer.End Of SieREAR CONTROL VALVE BODY DISASSEMBLY [GF4AX-EL]ezf051721100149Caution Denting or scratching these precisely machined components will reduce the ability or the transaxle to shift properly. When handling these components or the valve body that contains them, be careful not to drop or hit them. Using a magnet in this procedure could magnetize the valve body inner components, reducing the ability of the transaxle to shift properly. Do not use magnets or magnetized tools when carrying out maintenance on these components.Note If a valve does not slide out under its own weight, place the valve body open-side down and tap on the valve body lightly with a plastic hammer.1. Disassemble in the order indicated in the table.Warning Using compressed air can cause dirt and other particles to fly out, causing injury to the eyes. Wear protective eye wear whenever using compressed air.w6u517ae7w6u517ae805-17B50AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]2. Clean all parts and holes using compressed air and apply ATF to them immediately before assembly..End Of SieREAR CONTROL VALVE BODY INSPECTION [GF4AX-EL]ezf051721100150Spring Inspection1. Measure the spring free length. If not within the specifications, replace the spring.SpecificationsEnd Of Siew6u517ae91 Manual valve2 Stop pin3 Pressure regulator plug sleeve4 Pressure regulator plug5 Pressure regulator spring seat6 Pressure regulator spring7 Pressure regulator valve8 Stop pin9 2-3 timing plug10 2-3 timing spring11 2-3 timing valve12 Rear control valve bodySpringOuter diameter (mm {in})Free length (mm {in})No. of coilsWire diameter (mm {in})Pressure regulator spring 12.0 {0.472} 33.9 {1.34} 7.0 1.1 {0.043}2-3 timing spring 4.7 {0.19} 22.3 {0.878} 14.0 0.65 {0.026}AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B5105REAR CONTROL VALVE BODY ASSEMBLY [GF4AX-EL]ezf051721100151Assembly Procedure1. Install the 2-3 timing valve, 2-3 timing spring, 2-3 timing plug, and stop pin.2. Install the pressure regulator valve, pressure regulator spring, pressure regulator spring seat, pressure regulator plug, pressure regulator plug sleeve, and stop pin.3. Install the manual valve.End Of Siew6u517aeaw6u517aebw6u517aec05-17B52AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]CONTROL VALVE BODY ASSEMBLY [GF4AX-EL]ezf051721100152.ymu517aab1 Main control valve body2 Oil strainers3 Rubber balls4 Oil strainers5 Rubber balls6 Main/rear front gasketAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B5305Assembly Procedure1. Install the oil strainer and rubber balls into the main control valve body.2. Install the oil strainer and rubber ball into the rear control valve body.3. Set the new main/rear front gasket, rear separator plate, and new main/rear rear gasket on the rear control valve body. Refer to the figure to distinguish the two gaskets.4. Set the rear control valve body onto the main control valve body.7 Rear separator plate8 Main/rear rear gasket9 Rear control valve body10 Shift solenoid C11 Shift solenoid B12 Oil baffle13 Oil pipe component14 Oil strainer15 Rubber ball16 Premain/main rear gasket17 Main separator plate18 Premain/main front gasket19 Oil strainer20 Rubber ball21 Jet orifice and nut22 Premain control valve body23 Rubber ball24 Front/premain rear gasket25 Premain separator plate26 Front/premain front gasket27 Front control valve body28 TCC control solenoid valve29 Shift solenoid A30 3-2 timing solenoid valve31 Pressure control solenoid valve32 TFT sensorw6u517aeew6u517aefw6u517aeg05-17B54AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]5. Install and hand-tighten the bolts shown in the figure. Each type of bolt has a different letter on its head. Match the bolt letter with the letter stamped next to its installation hole on the valve body.6. Install the oil strainers and rubber balls into the main control valve body.7. Install the oil strainer and rubber balls into the premain control valve body.8. Install the jet orifice and nuts to the main separator plate.Tightening torque1.72.2 Nm {1723 kgfcm, 1519 inlbf}9. Set a new premain/main rear gasket, main separator plate, and new premain/main front gasket on the premain control valve body. Refer to the figure to distinguish the two gaskets.10. Set the premain control valve body onto the main control valve body.w6u517aehw6u517aejw6u517aekw6u517aelw6u517aemAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B550511. Install and hand-tighten the bolts indicated by the arrows. Each type of bolt has a different letter on its head. Match the bolt letter with the letter stamped next to its installation hole on the valve body.12. Install the rubber ball into the premain control valve body.13. Install the rubber ball into the front control valve body.14. Set a new front/premain rear gasket, premain separator plate, and new front/premain front gasket on the front control valve body. Refer to the figure to distinguish the two gaskets.15. Set the front control valve body onto the premain control valve body.16. Install and hand-tighten the bolts indicated by the arrows. Each type of bolt has a different letter on its head. Match the bolt letter with the letter stamped next to its installation hole on the valve body.w6u517aenw6u517aepw6u517aeqw6u517aerw6u517aes05-17B56AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]17. Install four control valve body bolts as shown for alignment.18. Tighten the mounting bolts.(1) Tighten the front control valve body.Tightening torque6.57.8 Nm {6680 kgfcm, 5869 inlbf}(2) Tighten the rear control valve body.Tightening torque6.57.8 Nm {6680 kgfcm, 5869 inlbf}19. Apply ATF to new O-rings and install them onto the solenoid valve.20. Install the solenoid valve.Tightening torque6.57.8 Nm {6680 kgfcm, 5869 inlbf}21. Apply ATF to new O-ring and install them onto the oil pipe component.22. Install the oil pipe component.Tightening torque6.57.8 Nm {6680 kgfcm, 5869 inlbf}23. Install the baffle plate.Tightening torque6.57.8 Nm {6680 kgfcm, 5869 inlbf}24. Install the TFT sensor.Tightening torque6.57.8 Nm {6680 kgfcm, 5869 inlbf}End Of SiedifferentialFRONT DIFFERENTIAL PREINSPECTION [GF4AX-EL]ezf051727100102Backlash Inspection1. Measure the backlash of the side gear. If not as specified, replace parts as necessary. BacklashStandard: 0.0250.10 mm {0.00100.0039 in}Maximum: 0.10 mm {0.0039 in}End Of Siew6u517aetymu517aacAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B5705FRONT DIFFERENTIAL DISASSEMBLY [GF4AX-EL]ezf0517271001031. Disassemble in the older indicated in the table..Sun Gear Disassembly Note1. Install the SST to the front differential as shown.2. Remove the sun gear using the press.98754310151614131112SSTR61261091213SSTRbue517zaa0021 Bolts2 Ring gear3 Sun gear(See 05-17B-57 Sun Gear Disassembly Note.)4 Screw5 Differential cover6 Bearing (See 05-17B-58 Bearing Disassembly Note)7 Thrust washer8 Side gear9 Roll pin10 Pinion shaft11 Pinion carrier12 Pinion gear13 Thrust washer14 Side gear15 Thrust washer16 Gear casebuj0517a29705-17B58AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]Bearing Disassembly Note1. Remove the bearing (sun gear side) from the gear case using the SSTs.2. Remove the bearing (ring gear side) from the gear case using the SST.End Of SieFRONT DIFFERENTIAL ASSEMBLY [GF4AX-EL]ezf051727100104Assembly Procedure1. Apply ATF to each part immediately before assembly.2. Set the sun gear onto the gear case.3. Install the bearing using the SST.4. Install the thrust washer to the gear case.5. Install the side gear.ymu517aaexme5614a033buj0517a401AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B59056. Install the pinion gears and thrust washers into the gear case.7. Install the pinion carrier.8. Install the pinion shafts.Caution Assemble the roll pin so that the roll pin opening is perpendicular to the pinion shaft.9. Install the roll pin, and crimp it to prevent it from coming out of the gear case.10. Install the side gear and thrust washer.11. Install the differential cover.Tightening torque7.910.7 Nm {80110 kgfcm, 7095 inlbf}ymu517aahymu517aajymu517aakymu517aalymu517aam05-17B60AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]12. Measure the backlash of the side gear as follows: (1) Install the left and right drive shafts in the differential.(2) Support the drive shaft on V-blocks.(3) Measure the backlash of both side gears. If the backlash is not within the specification, adjust the thrust washer.BacklashStandard: 0.0250.10 mm {0.00100.0039 in}Maximum: 0.10 mm {0.0039 in}13. Select the thrust washer so that the backlash is as specified.Thickness of thrust washermm {in}14. Install the SST to locate gear case and sun gear.15. Install the sun gear using the press.16. Install the ring gear.Tightening torque152176.5 Nm {15.517.9 kgfm, 112130 ftlbf}End Of Sieoutput gearOUTPUT GEAR BEARING PRELOAD [GF4AX-EL]ezf0517192041031. Align the bearing cover with guide bolts as shown.2. Press the bearing cover in using the SST.3. Remove the guide bolts and install the bearing cover installation bolts.Tightening torque10.813.7 Nm {110140 kgfcm, 96121 inlbf}4. Mount the converter housing onto the SST (transaxle hanger).5. Remove the bearing race and adjustment shims from the bearing housing using a pin punch and a hammer.6. Set the output gear into the converter housing.7. Install the bearing race removed in Step 5 to the selector, and install the selector and bearing race to the output gear.2.00 {0.078} 2.05 {0.080} 2.10 {0.083}2.15 {0.085} 2.20 {0.087} ymu517aapbuj0517a408w6u517af2w6u517af3AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B61058. Turn the selector to eliminate the gap between its two halves.9. Set the SST (collars) in the position shown.10. Set the bearing housing on the SST (selector) and install the SST (bolts). Tighten the bolts to the specified torque.Tightening torque27.434.3 Nm {2.793.5 kgfm, 20.225.3 ftlbf}11. Turn the SST (selector) to increase the clearance (arrow) with the SST (bars) until it no longer turns.12. Turn the selector in the opposite direction until the preload is eliminated (gap is reduced).ymu517aaqw6u517af5w6u517af6w6u517af705-17B62AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]13. Mount the SSTs and a pull scale or a torque wrench on the output gear.14. Adjust the clearance of the SST (selector) to obtain the specified preload/pull scale reading.Preload0.91.6 Nm {917 kgfcm, 7.914.7 inlbf}Reading on pull scale916 Nm {0.91.7 kgf, 2.03.7 lbf}Note Measure the clearance around the entire circumference, and select shims equivalent to the maximum clearance. The maximum allowable number of adjustment shims is seven.15. Measure the gap between A and B around the circumference of the SST (selector) using a feeler gauge.16. Take the maximum reading and determine the shims to be used. Use no more than one shim.Thickness of shimmm {in}17. Remove the bearing housing and the SST.18. Install the required shims and press the bearing race into the bearing housing using the SST.19. Install the output gear and idler gear.20. Install the bearing housing.Tightening torque27.434.3 Nm {2.793.5 kgfm, 20.225.3 ftlbf}0.375 {0.015} 0.425 {0.017} 0.475 {0.019} 0.50 {0.020}0.525 {0.021} 0.55 {0.022} 0.575 {0.023} 0.60 {0.024}0.625 {0.025} 0.65 {0.026} 0.675 {0.027} 0.70 {0.028}0.725 {0.029} 0.75 {0.030} 0.775 {0.031} 0.80 {0.031}0.825 {0.032} 0.85 {0.033} 0.875 {0.034} 0.90 {0.035}0.925 {0.036} 0.95 {0.037} 0.975 {0.038} 1.00 {0.039}1.025 {0.040} 1.05 {0.041} 1.075 {0.042} 1.10 {0.043}1.125 {0.044} 1.15 {0.045} 1.175 {0.046} 1.20 {0.047}1.225 {0.048} 1.25 {0.049} 1.275 {0.050} 1.30 {0.051}1.325 {0.052} 1.35 {0.053} 1.375 {0.054} 1.40 {0.055}w6u517af8ymu517aarw6u517afaAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B630521. Verify that the preload/pull scale reading is within the specification. If not, return to Step 5.Preload0.92.0 Nm {921 kgfcm, 7.918.2 inlbf} Reading on pull scale920 Nm {0.92.1 kgf, 2.04.6 lbf}22. Remove the bearing housing and output gear component.End Of SiedifferentialFRONT DIFFERENTIAL BEARING PRELOAD [GF4AX-EL]ezf0517271001051. Remove the bearing race and adjustment shims from the transaxle case.2. Install the bearing race into the converter housing using a suitable pipe.3. Remove the ring gear.4. Remove the sun gear.5. Remove the differential cover.6. Remove the roll pin.7. Remove the short pinion shaft.8. Install the differential cover.Tightening torque7.910.7 Nm {80110 kgfcm, 69.595.4 inlbf}9. Set the differential into the converter housing.10. Turn the selector to eliminate the gap between its two halves.11. Install the bearing race removed in Step 1 into the SST. Set the SST and bearing race onto the differential.w6u517afbw6u517afcw6u517afd05-17B64AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]12. Set the six SST (collars) on the converter housing in the positions shown.13. Set the transaxle case on the converter housing.14. Tighten the SST (bolts) to the specified torque.Tightening torque3851 Nm {3.85.3 kgfm, 2838 ftlbf}Note Bend the bar as shown to turn the SST.15. Turn the SST (selector) to increase the clearance (arrow) using the SST (bars), until it no longer turns. This is to seat the bearing race.16. Turn the selector in the opposite direction until the preload is eliminated (gap is reduced).17. Install the SST through the transaxle case and attach it to the pinion shaft.w6u517afew6u517affw6u517afgAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B650518. Install the SST and a pull scale or torque wrench.Note Read the preload when the differential starts to turn. Measure several times and calculate the average value.19. Adjust the clearance of the SST (selector) to obtain the specified preload/pull scale reading.Preload0.5 Nm {5 kgfcm, 4.3 inlbf}Reading on pull scale5 N {0.5 kgf, 1.1 lbf}Note Measure the clearance around the entire circumference, and select shims based on the maximum clearance. The maximum allowable number of adjustment shims is three.20. Measure the clearance as shown.21. Add 0.3 mm {0.0118 in} to the measured clearance, and select the shims closest in value to that measurement.Thickness of shimmm {in}22. Remove the transaxle case and SST (selector).23. Install the required adjustment shims and tap the bearing race into the transaxle case.24. Install the transaxle case.Tightening torque3851 Nm {3.85.3 kgfm, 2838 ftlbf}25. Install the SST to the pinion shaft through the transaxle case.Note Measure several times and calculate the average value.26. Verify that the preload is within the specification. If not, return to Step 1.Preload3.03.9 Nm {3040 kgfcm, 2734 inlbf}Reading on pull scale3039 N {3.04.0 kgf, 6.68.8 lbf}27. Remove the differential cover.28. Install the short pinion gear.29. Install the new roll pin.0.1 {0.0039} 0.12 {0.0047} 0.14 {0.0055}0.16 {0.0062} 0.18 {0.0071} 0.20 {0.0079}0.50 {0.0197} 0.70 {0.0276} 1.0 {0.0394}w6u517afhw6u517afjw6u517afk05-17B66AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]30. Install the differential cover.Tightening torque.7.910.7 Nm {80110 kgfcm, 7095 inlbf}31. Install the sun gear.32. Install the ring gear.Tightening torque.152176.5 Nm {15.517.9 kgfm, 112130 ftlbf}End Of Sieautomatic transaxleAUTOMATIC TRANSAXLE AND TRANSFER ASSEMBLY [GF4AX-EL]ezf051700000109PrecautionGeneral notes1. Select the adjustment shims, referring to Bearing Preload.2. If the drive plates or 2-4 brake band are replaced with new ones, soak the new part in ATF for at least two hours before installation.3. Before assembly, apply ATF to all seal rings, rotating parts, O-rings, and sliding parts.4. All O-rings, seals, and gaskets must be replaced with the new ones included in the overhaul kit.5. Use petroleum jelly, not grease, when assembling again.6. When it is necessary to replace a bushing, replace the subassembly that includes that bushing.7. Assemble the housing within 10 minutes after applying sealant, and allow it to cure for at least 30 minutes after assembly before filling the transaxle with ATF.Warning Although the stand has a self-locking brake system, there is a possibility that the brake may not hold when the transaxle is held in a lopsided position on the stand. This would cause the transaxle to turn suddenly, causing serious injury. Never keep the transaxle tilted to one side. Always hold the rotating handle firmly when turning the transaxle.AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B6705AssemblyBearing and race locationsNote The bearing and race at locations 2, 3, 4, 6, and 7 are one-piece units.Outer diameter of bearing and racew6u517afl1 2 3 4 5 6 7Bearing (mm {in}) 86.1 {3.39} 56.1 {2.21} 62.15 {2.447} 62.15 {2.45} 72.0 {2.83} 56.1 {2.21} 71.0 {2.80}Race (mm {in}) 88.0 {3.46} 72.0 {2.83} 57.0 {2.24} 72.0 {2.83}05-17B68AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]Components.Nm {kgfcm, inlbf}27.434.3 Nm {2.793.5 kgfm, 20.225.3 ftlbf}7.910.7{80110, 7095}98754310151614131112SSTR6124RRRRRSSTSSTSST4.05.8{4060, 3552}10.813.7 {110140, 96121}66654bue517zaa0011 Converter housing2 Baffle plate3 O-rings4 Oil seals5 Adjustment shim6 Bearing races7 Bearing cover component8 Output gear9 Idler gear10 Bearing housing11 Baffle plate12 Roll pin13 Orifice check valve14 Orifice check spring15 2-3 accumulator16 Front differentialAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B6905.bue517zab0621 Baffle plate2 Parking pawl3 Parking assist lever4 Actuator support5 Manual shaft and manual plate6 Detent spring7 Low and reverse brake8 Output shell9 Transaxle case05-17B70AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL].bue517zab0631 Turbine shaft2 3-4 clutch3 Internal gear4 Low and reverse brake5 Retaining plate6 Snap ring7 Friction plate8 One-way clutch 2 and carrier hub component9 Band servo10 Anchor strut and shaft11 2-4 brake band12 Small sun gear and one-way clutch 113 Clutch component14 Snap ring15 Piston stemAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B7105.bue517zab0641 Oil pump2 Control valve body3 Coupler component4 Control valve body cover5 Oil strainer6 Oil pan7 Oil pipe8 TR switch9 Input/turbine speed sensor10 Transfer11 Oil dipstick and oil filler tube12 Oil pump shaft13 Torque converter05-17B72AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]Assembly procedure1. Align the bearing cover with guide bolts as shown and press it in. Install and tighten the mounting bolts.Tightening torque10.813.7 Nm {110140 kgfcm, 96121 inlbf}2. Press the bearing race into the converter housing.3. Assemble the SST.4. Install the idler gear and output gear by tapping in with a plastic hammer.5. Install the selected shims and bearing race into the bearing housing using the SST.6. Install the bearing housing.(1) Install the bearing housing on the converter housing, and tighten the bolts evenly and gradually.Tightening torque27.434.3 Nm {2.793.5 kgfm, 20.225.3 ftlbf}(2) Align the slot of the idler shaft with the mark on the bearing housing.(3) Tap a new roll pin in using a pin punch and a hammer.7. Install the 2-3 accumulator piston.(1) Install the orifice check valve spring and orifice check valve.(2) Apply ATF to new O-rings and install them into the 2-3 accumulator.(3) Install the 2-3 accumulator piston.Tightening torque7.910.7 Nm {80110 kgfcm, 7095 inlbf}8. Install the bearing race into the converter housing.9. Install the baffle plate.Tightening torque4.05.8 Nm {4060 kgfcm, 3552 inlbf}10. Install the front differential.11. Install the selected shims and bearing race into the transaxle case.w6u517afrw6u517afsw6u517aftAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B730512. Install the manual shaft and manual plate.(1) Install the manual plate, spacer, washer, and nut.(2) Tighten the nut to the specified torque.Tightening torque4254 Nm {4.25.6 kgfm, 3140 ftlbf}(3) Install the detent spring.Tightening torque1521 Nm {1.52.2 kgfm, 1115 ftlbf}(4) Move the manual shaft and verify that the parking pawl operates correctly.13. Install the output shell to the output gear, and install the thrust bearing onto the output shell.Thrust bearing outer diameter71.0 mm {2.80 in}14. Apply a light coat of silicone sealant to the contact surfaces of the converter housing and the transaxle case.15. Install new O-rings into the converter housing.16. Install the transaxle case on the converter housing, and tighten the bolts evenly and gradually.Tightening torque3851 Nm {3.85.3 kgfcm, 2838 inlbf}17. Install the SST into the differential side gears.18. Install the turbine shaft and 3-4 clutch component.(1) Assemble the turbine shaft and 3-4 clutch component.(2) Verify that the thrust bearing and race are properly installed.(3) Install the turbine shaft and 3-4 clutch component into the transaxle case.w6u517afubuj0517a332w6u517afv05-17B74AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]19. Adjust the SST position so that it contacts and holds the turbine shaft.20. Install the internal gear.(1) Install the internal gear to the output shell.(2) Install the snap ring.21. Install the carrier hub component.(1) Verify that the thrust bearing and bearing race are installed in the correct position.(2) Hold the turbine shaft with one hand to prevent it from rotating.(3) Install the carrier hub component into the 3-4 clutch drum by rotating it.22. Install the friction plate.23. Install the one-way clutch 2.(1) Hold the one-way clutch 2 horizontally.(2) Install it by turning the carrier hub component counterclockwise.(3) Install the snap ring.24. Install the band servo to the transaxle case.(1) Install the servo return spring and band servo.(2) Compress the servo using the SSTs.(3) Install the snap ring.(4) Remove the SSTs.25. Install the piston stem.26. Loosely tighten the piston stem by hand.27. Install the anchor strut.28. Install the 2-4 brake band in the transaxle case, and interlock it to the anchor as shown.29. Install the small sun gear and one-way clutch 1.(1) Verify that the thrust bearing and bearing race are installed in the correct position.(2) Install the small sun gear and one-way clutch 1 component by rotating it.30. Install the clutch component.(1) Verify that the thrust bearing is installed in the correct position.(2) Install the clutch component by rotating it.31. Measure the height difference between the reverse and forward drum and the transaxle case. If the height is not within specification, assemble again beginning with Step 21.Height difference0.71.9 mm {0.0280.075 in}32. Install the new snap ring into the bottom ring groove of the turbine shaft.w6u517afww6u517afxw6u517afyw6u517afzAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B750533. Use the following procedure to adjust the total end play and select a suitable bearing race.(1) Set the thrust bearing onto the clutch component.(2) Remove the bearing race and the oil pump gasket.(3) Set the thickest bearing race (2.2 mm {0.084 in}) onto the oil pump.(4) Set the oil pump onto the clutch component.(5) Measure clearance A between the transaxle case and the oil pump. Take several measurements and calculate the average value.(6) Select a suitable bearing race from the chart below.(7) Remove the oil pump.(8) Place the selected bearing race and a new gasket onto the oil pump.(9) Install the oil pump onto the clutch component, and tighten the bolts evenly and gradually.Tightening torque1925 Nm {1.92.6 kgfm, 1418 ftlbf}(10)Install the oil pipe.34. Adjust the 2-4 brake band.(1) Loosen the locknut and tighten the piston stem to the specified torque.Tightening torque11.814.7 Nm {120150 kgfcm, 105130 inlbf}(2) Install a dial indicator and magnetic base to the oil pump. Set the dial indicator against the piston stem.Warning Using compressed air can cause dirt and other particles to fly out, causing injury to the eyes. Wear protective eye wear whenever using compressed air.(3) While keeping compressed air applied to the 2-4 brake band engagement passage, set the dial indicator to zero.Air pressure390400 kPa {3.94.1 kgf/cm2, 5658 psi}(4) Stop applying compressed air, and verify the piston stroke by inspecting the dial gauge. Adjust the piston stem and apply compressed air repeatedly until the stroke is within specification.Stroke0.81.2 mm {0.03940.0472 in}Clearance A (mm {in})Select this bearing race (mm {in})0.911.10 {0.036-0.043} 1.2 {0.047}0.710.90 {0.028-0.035} 1.4 {0.055}0.510.70 {0.020-0.027} 1.6 {0.063}0.310.50 {0.012-0.019} 1.8 {0.071}0.110.30 {0.004-0.011} 2.0 {0.078}00.10 {0-0.003} 2.2 {0.087}w6u517ag0w6u517ag1w6u517ag205-17B76AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL](5) Hold the piston stem and tighten the locknut to the specified torque.Tightening torque2539 Nm {2.54.0 kgfm, 1928 ftlbf}35. Install a new O-ring and oil strainer to the transaxle.Tightening torque7.910.7 Nm {80110 kgfcm, 7095 inlbf}36. Install the magnets inside the oil pan in the positions shown in the figure.37. Apply a light coat of silicone sealant to the contact surfaces of the transaxle case and the oil pan.38. Install the oil pan to the transaxle case.Tightening torque8.410.7 Nm {85110 kgfcm, 73.895.4 inlbf}39. Align the manual valve with the pin on the manual plate.40. Install the control valve body into the transaxle case, and tighten the bolts evenly and gradually.Tightening torque10.814.7 Nm {110150 kgfcm, 96130 inlbf}41. Install a new O-ring to the coupler component.42. Install the coupler component.43. Match the harness coupler, and connect the solenoid connectors and TFT sensor connector.44. Apply a light coat of silicone sealant to the contact surfaces of the transaxle case and control valve body cover.45. Install a control valve body cover, and tighten the bolts evenly and gradually.Tightening torque8.410.7 Nm {85110 kgfcm, 73.895.4 inlbf}46. Install the steel ball, spring, packing, and oil pipe.47. Install the bolt.Tightening torque7.910.7 Nm {80110 kgfcm, 7095 inlbf}48. Install the input/turbine speed sensor.Tightening torque7.910.7 Nm {80110 kgfcm, 7095 inlbf}49. Install the TR switch.w6u517ag3w6u517ag4AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B770550. Adjust the TR switch.(1) Connect an ohmmeter between the terminals A and H.(2) Rotate the manual shaft fully counterclockwise, then return it two notches to the N position.(3) Adjust the switch to the point where there is continuity between the terminals.(4) Tighten the switch.Tightening torque7.910.7 Nm {80110 kgfcm, 7095 inlbf}Note When it is necessary to install the manual shaft lever to the manual shaft, use an adjustable wrench to hold the manual shaft lever, then use a wrench other than an impact wrench to tighten the manual shaft nut to the specified torqueCaution Do not use an impact wrench or tighten the manual shaft nut without holding the manual shaft lever, as the transaxle may become damaged.51. Tighten the manual shaft nut.Tightening torque3246 Nm {3.24.7 kgfm, 2433 ftlbf}52. Remove the transaxle from the SST (transaxle hanger).53. Install a new O-ring to the transfer.54. Install the transfer to the converter housing.Tightening torque36.553.9 Nm {3.735.49 kgfm, 27.039.7 ftlbf}55. Install the oil dipstick and oil filler tube along with a new O-ring to the transaxle case.Tightening torque6.99.8 Nm {80110 kgfcm, 69.595.4 inlbf}56. Install the oil pump shaft.57. Install a new O-ring onto the turbine shaft.58. If the torque converter has been drained and washed, hold the torque converter in an upright position and fill it with new ATF.ATF typeM-III or equivalent (e.g.DexronII)59. Carefully install the converter to the torque converter housing. Rotate the torque converter to align the splines.60. To ensure that the torque converter is installed accurately, measure distance A between the end of the torque converter and the face of the converter housing.Distance A16.20 mm {0.6378 in}End Of Sietransferw6u517ag5buj0517a344DISTANCE (A)bue517zab00805-17B78AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]TRANSFER CLEANING [GF4AX-EL]ezf051727500103Cleaning Precautions1. Clean the surface of the transfer using steam and cleaning fluids when disassembly.Warning Always wear safety glasses when using compressed air since the foreign material could be blown by the compression air and damage your eyes.2. Clean removed components with cleaning fluids and use compressed air to blow off the oil. Clean the oil holes and passages with compressed air.End Of SieTRANSFER DISASSEMBLY [GF4AX-EL]ezf051727500104Before Service Precautions To prevent the foreign material from entering the transfer, perform disassembly and servicing in a clean, dust-free environment. Inspect the each part while disassembling. Disassemble with bare hand or using vinyl gloves. To prevent foreign material from entering the transfer, do not use cotton work gloves or rag. When disassembling areas of the transfer that are made of light alloy, tap lightly with a plastic hammer. Do not use a flathead screwdriver. Warning The engine stand is equipped with a self-lock mechanism. However, if the transfer is tilted, the self-lock mechanism could become inoperative. This could cause the transfer to rotate accidentally, resulting in injury. Therefore, make sure that the transfer is not tilted when it is on the engine stand. When turning the transfer, grasp the rotation handle firmly.Disassembly.buj0517a3461 Side cover2 Rear cover3 Locknut (idle gear)4 Locknut (companion flange)5 Washer6 Companion flange7 Oil seal8 Idle gearAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B7905Disassembling Procedure1. Remove the rear cover and drain the transfer oil.2. Assemble the SST.3. Install the transfer to the SST.4. Remove the side cover.5. Remove the O-ring from the side cover.6. Using the SST, secure the companion flange, and remove the idle gear locknut.7. Using the SST, secure the companion flange, and remove the locknut and washer. 9 Spacer10 Bearing cap11 Spacer12 Adjustment shim13 Ring gear component14 Bearing outer race (side)15 Drive pinion gear16 Bearing inner race (rear)17 Collapsible spacer18 Bearing inner race (front)19 Spacer20 Clip21 Bearing22 Oil seal23 Spacer24 Bearing outer race (rear)25 Bearing outer race (front)26 Bearing inner race (side)27 Ring gear28 Ring gear shaft29 Transfer carrierbuj0517a347buj0517a348buj0517a34905-17B80AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]8. Using the SST, remove the companion flange.9. Using a flathead screwdriver, remove the oil seal.10. Using a copper hammer and pin punch, tap the idle gear locknut lightly to remove the idle gear.11. Remove the spacer (locknut side).12. Make alignment marks on the bearing cap and carrier.13. Remove the bearing cap.14. Using the SSTs, remove the ring gear component.15. Remove the spacer (idle gear side).16. Install an appropriate nut to the drive pinion to prevent the thread from being damaged.17. Lightly tap the drive pinion using a copper hammer and remove the drive pinion.18. Remove the bearing inner race (rear) and distance piece.19. Using the SST, remove the bearing inner race (front).20. Remove the spacer.21. Detach the clip.buj0517a350buj0517a351buj0517a352buj0517a353buj0517a354AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B810522. Using the SST, remove the bearing. 23. Using a flathead screwdriver, remove the oil seal.24. Attach the brass stick to the notch, tap the race end lightly and evenly, then remove the outer race. 25. Using the SSTs, remove the bearing inner race (side) (locknut side).26. Using the SSTs, remove the bearing inner race (side), then remove the ring gear.End Of Siebuj0517a355buj0517a35649 H027 00249 0839 425C39.5 mm {1.56 in})(ATTACHMENTbue517zab00149 H027 00249 0839 425C39.5 mm {1.56 in})(ATTACHMENTbue517zab00205-17B82AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]TRANSFER ASSEMBLY [GF4AX-EL]ezf051727500105Before Service Precautions Assemble with bare hand or using vinyl gloves. To prevent the foreign material from entering the transfer, do not use cotton work gloves or rag. Apply sufficient gear oil to the sliding surfaces and O-rings, and be careful not to damage when assembling. Replace the transfer with a new one if the case alignment surface is damaged. Be careful not to damage it since it may cause oil leakage. When installing silicone sealant, clean off the old sealant adhering to the sealing area and clean the sealing area with the cleaning fluids. After installing a seal, leave the parts alone for 2 h or more. Do not add oil or operate the vehicle during this time. Warning The engine stand is equipped with a self-lock mechanism. However, if the transfer is tilted, the self-lock mechanism could become inoperative. This could cause the transfer to rotate accidentally, resulting in injury. Therefore, make sure that the transfer is not tilted when it is on the engine stand. When turning the transfer, grasp the rotation handle firmly.Assembly.buj0517a3591 Transfer carrier2 Ring gear shaft3 Ring gear4 Bearing inner race (side)5 Bearing outer race (front)6 Bearing outer race (rear)7 Spacer8 Oil seal9 Bearing10 Clip11 Spacer12 Bearing inner race (front)13 Distance piece14 Bearing inner race (rear)15 Drive pinion gear16 Bearing outer race (side)17 Ring gear component18 Adjustment shim19 Spacer20 Bearing cap21 Spacer22 Idle gearAUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B8305Assembly Procedure1. Assemble the SST.2. Install the transfer to the SST.3. Using a press, assemble the locknut side bearing inner race (side) to the ring gear shaft.4. Using a press assemble the ring gear to the ring gear shaft.5. Using a press, assemble the ring gear side bearing inner race (side).6. Using the SSTs, assemble the bearing outer race.23 Oil seal24 Companion flange25 Washer26 Locknut (companion flange)27 Locknut (idle gear)28 Rear cover29 Side coverbuj0517a360buj0517a361buj0517a362buj0517a36305-17B84AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]7. Using the SSTs, adjust the drive pinion height as follows: (1) Install the SSTs to the removed spacer and bearing.(2) Assemble the spacer, bearing and SSTs. Using an O-ring, secure the SST.(3) Assemble the bearing, SSTs, companion flange, washer, and nut.(4) Tighten the nut to the companion flange to where it can still be rotated by hand.(5) Place the SSTs on the plate surface and set the dial gauge to 0.(6) Position the SST (49 0727 570) on the driver pinion model.(7) Attach the dial gauge head to where the carrier bearing outer race (side) is installed and measure lowest position. Also, measure the value of where the side bearing outer race (side) is installed on the opposite side. (8) Add the values for the both sides measured in Step 7 and divide by 2. From this value, subtract the value listed on the drive pinion end (if not written, it is 0) divided by 100, and then add 1.47. This is the pinion height adjustment value.buj0517a364buj0517a365buj0517a366buj0517a367AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B8505Note If the value measured in Step 7 and 8 is -1.47 mm {-0.0579 in} and 1.45 mm {0.0571 in}, and the drive pinion end value is 2, the formula would be (-1.47)+ (-1.45)/2-2/100+1.47=-0.01. Therefore, a spacer 0.01 mm {0.0004 in} thinner than the old one would be used. Since spacer thickness varies by 0.015 mm {0.0020 in}, select the spacer nearest the required size and assemble. 8. Assemble the spacer selected for pinion height adjustment with the round off side facing the gears.9. Using the SST, assemble the bearing inner race (front) to the drive pinion gear.10. Assemble a new distance piece to the drive pinion gear.11. Assemble the drive pinion to the transfer carrier.12. Install the bearing inner race (rear), companion flange, washer, and new locknut to the drive pinion and temporarily tighten.13. Rotate the companion flange by hand and to seat the bearing.14. Using the SST, tighten the locknut from the lower limit of the specified tightening torque and set to the preload value. Note the tightening torque when the specified preload value is obtained.Tightening torque127284 Nm {13.029.0 kgfm, 95209 ftlbf}Drive pinion preload value0.881.37 Nm {9.014.0 kgfcm, 7.912.1 inlbf}15. Remove the locknut, washer, and companion flange.16. Apply oil to the lip area of a new oil seal.17. Using the SST, assemble the oil seal.18. Apply the grease to the bearing contact surface of the companion flange.19. Assemble the companion flange.Identification mark Thickness (mm {in}) Identification mark Thickness (mm {in})08 3.08 {0.1213} 09 3.095 {0.1219}11 3.11 {0.1224} 12 3.125 {0.1230}14 3.14 {0.1236} 15 3.155 {0.1242}17 3.17 {0.1248} 18 3.185 {0.1254}20 3.20 {0.1260} 21 3.215 {0.1266}23 3.23 {0.1272} 24 3.245 {0.1278}26 3.26 {0.1283} 27 3.275 {0.1289}29 3.29 {0.1295} 30 3.305 {0.1301}32 3.32 {0.1307} 33 3.335 {0.1313}35 3.35 {0.1319} 36 3.365 {0.1325}38 3.38 {0.1331} 39 3.395 {0.1335}41 3.41 {0.1343} 42 3.425 {0.1348}44 3.44 {0.1354} 45 3.455 {0.1360}47 3.47 {0.1366} 7 INCH SIDE/8 INCH SIDESPACER49 F401 33149 F401 337Abue517zab003buj0517a37005-17B86AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]20. Using the SST, tighten the new locknut to the tightening torque noted when preload was adjusted.21. Reverify the preload.Preload value0.881.37 Nm {9.014.0 kgfcm, 7.912.1 inlbf}22. Install the spacer to the bearing outer race (side) locknut side installation area.23. Place the side bearing race and on top of ring gear on the surface plate as shown in the figure, and measure the height using a vernier caliper and straight edge. This is dimension A.24. Measure the width of the transfer carrier ring gear installation area with the spacer installed. This is dimension B.25. Total thickness C of the adjustment shims on both sides can be expressed by the following formula: C1=B-A+0.096C2=B-A+0.2826. If the total thickness of the installed adjustment shims is between C1C2, use the shims as they are. 27. If the total thickness of the installed adjustment shims is not between C1C2, select two appropriate adjustment shims from the table below and use them.Note When reusing adjustment shims, do not mix up the right one and left. Do not mix up the right and left side bearing race and spacer.28. Install the adjustment shim chose for the transfer carrier ring gear side and spacer on opposite side.29. Assemble the ring gear and bearing race to the transfer carrier.buj0517a371buj0517a372BSPACERbue517zab004Identification mark Thickness (mm {in}) Identification mark Thickness (mm {in})350 3.50 {0.1378} 355 3.55 {0.1398}360 3.60 {0.1417} 365 3.65 {0.1437}370 3.70 {0.1457} 375 3.75 {0.1476}380 3.80 {0.1496} 385 3.85 {0.1516}390 3.90 {0.1535} 395 3.95 {0.1555}400 4.00 {0.1574} 405 4.05 {0.1594}410 4.10 {0.1614} 415 4.15 {0.1634}420 4.20 {0.1654} 425 4.25 {0.1673}430 4.30 {0.1693} 435 4.35 {0.1713}440 4.40 {0.1732} 445 4.45 {0.1752}450 4.50 {0.1772} 455 4.55 {0.1791}460 4.60 {0.1811} AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B870530. Using the SST, assemble the selected adjustment shim in between the spacer and bearing race as shown in the figure.31. Align the alignment mark of the bearing cap, assemble the bearing cap, and tighten the bolt temporarily.32. Set the dial gauge with the measuring probe attached perpendicularly to the end of one of the ring gear teeth.33. Secure the drive pinion and measure the backlash from when the ring gear is moved.StandardBacklash: 0.090.11 mm {0.00350.0043 in}Caution Perform the backlash measurement on the ring gear circumference at four points.34. If the backlash is not within the specified range above, adjust it by sliding the ring gear in the shaft direction.Note Slide the ring gear in the shaft direction by replacing the adjustment shim. If the right side adjustment shim is replaced with one that is 0.05 mm {0.002 in} thicker, the left side shim must be replaced with one that is 0.05 mm {0.002 in} thinner.35. Align the bearing cap alignment mark and assemble the bearing cap.Tightening torque17.626.5 Nm {1.802.70 kgfm, 13.119.5 ftlbf}36. Perform the drive pinion and ring gear tooth contact inspection.(1) Apply tooth marking compound evenly to both surfaces of the ring gear.(2) Rotate the ring gear back and forth several times.(3) Inspect for gear tooth contact at four points on the ring gear circumference and verify that the gear tooth contact indicated by tooth marking compound is as indicated in the figure. If the tooth contact points are normal, wipe off the marking compound. If the tooth contact points are not normal, adjust the pinion height, then adjust the backlash.buj0517a374buj0517a375buj0517a369buj0517a37605-17B88AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL](4) If toe and flank contact is indicated as shown in the figure, replace the drive pinion spacer with a thinner one to maintain the drive pinion further away. (5) If heal and face contact is indicated as shown in the figure, replace the drive pinion spacer with a thicker one to bring the drive pinion closer.37. Assemble the idle gear side spacer.38. Using the SSTs, assemble the oil seal.39. Using the SSTs, assemble the bearing.40. Assemble the clip.41. Align the idle gear and ring gear shaft serrations and tap the idle gear lightly to assemble.42. Assemble the locknut side spacer.43. Assemble a new locknut.TOE CONTACT FLANK CONTACTbue517zab005TOE CONTACT FLANK CONTACTbue517zab006buj0517a379buj0517a380AUTOMATIC TRANSAXLE (SERVICE) [GF4AX-EL]05-17B890544. Using the SST, secure the companion flange and tighten the locknut to the specified tightening torque.Tightening torque127206 Nm {13.021.0 kgfm, 95151 ftlbf}45. Crimp the locknut using a chisel and hammer.Crimp size2.7 mm {0.11 in} or more46. Remove the transfer from the SST.47. Apply oil to a new O-ring and assemble the side cover.48. Assemble the side cover to the transfer.Tightening torque6.99.8 Nm {70100 kgfcm, 6186 inlbf}Note Before applying silicone sealant, completely clean off any old silicone sealant and remove any oil or grease. After applying silicone sealant, install the rear cover within 10 min. After connecting the sealing area, leave it for 30 min or more, then add transfer oil.49. Clean the alignment surface of the rear cover and transfer, and lightly apply silicone sealant.50. Assemble the rear cover.Tightening torque6.99.8 Nm {70100 kgfcm, 6186 inlbf}51. Remove the oil level plug and washer.52. Position the transfer on level ground.53. Add the specified oil through the oil level plug hole until it reaches the oil level plug hole filling port.Specified oilAPI Service GL-5 (SAE 80W-90) Oil capacity (approx. quantity)0.35 L {0.37 US qt, 0.31 lmp qt}End Of Siebuj0517a381LOCKNUT2.7 mm {0.11 in} OR MOREbue517zab007buj0517a383AUTOMATIC TRANSAXLE (SERVICE) [LA4AX-EL (CD4E)]05-17D1030599. Install the transaxle filler tube component.(1) Install the tube.(2) Install the transaxle filler tube bolt. Install the fluid level indicator.100.Install the turbine shaft speed (TSS) sensor.(1) Use petroleum jelly on the O-ring seal and position the TSS sensor. Install a new O-ring seal. (2) Install the TSS sensor bolt.101.Using the SST, install the LH differential seal.102.Using the SST, install the RH differential seal.103.Using the SST, install the torque converter fluid seal.Note Make sure the torque converter seal garter spring does not become dislodged during fitting. If the garter spring does become dislodged, install a new torque converter seal. Coat the torque converter seal garter spring with petroleum jelly.8 Nm {0.8 kgfm, 5.9 ftlbf}bue0517a03813 Nm {1.3 kgfm, 9.6 ftlbf}bue0517a03949 B001 795buj0517w039307-428(49 UN30 7428)buj0517w038v961011605-17D104AUTOMATIC TRANSAXLE (SERVICE) [LA4AX-EL (CD4E)]104.Install the drain plug. 105.Install the output shaft speed (OSS) sensor.106.Install the pump drive shaft.Note Inspect correct rotation of the pump drive shaft.107.Remove the transaxle from the SSTs.End Of Sie27 Nm {2.8 kgfm, 20 ftlbf}bue0517a040v9910123gd1439ayuj30701w02TECHNICAL DATA 05-5010505-50 TECHNICAL DATATRANSMISSION/TRANSAXLE TECHNICAL DATA [GF4AX-EL] . . . . . .05-501TRANSMISSION/TRANSAXLE TECHNICAL DATA [LA4AX-EL (CD4E)] . . . . . . . . . . . . . . . . 05-503End of Tocautomatic transaxleTRANSMISSION/TRANSAXLE TECHNICAL DATA [GF4AX-EL]ezf055000000101Automatic TransaxleItem SpecificationTransaxle type GF4AX-ELTorque converterBushing inner diameter (mm {in})Standard 53.030 {2.088}Maximum 53.076 {2.090}Oil pumpOuter and inner rotor clearance (mm {in})Standard 0.020.04 {0.00080.0015}Maximum 0.05 {0.0019}Spool outer diameter (mm {in})Standard 13.97013.980 {0.55000.5503}Maximum 13.970 {0.5500}Clearance between the oil pump base and the inner rotor (mm {in})Standard 0.0400.115 {0.001570.00453}Maximum 0.125 {0.00492}Forward clutchNumber of drive/driven plates 3/3Drive plate thickness (mm {in})Standard 1.6 {0.063}Minimum 1.5 {0.059}Forward clutch clearance (mm {in}) 0.971.20 {0.0380.047}Snap ring size (mm {in})2.00 {0.079}, 2.15 {0.085}, 2.30 {0.091}, 2.45 {0.096},2.60 {0.102}, 2.75 {0.108}Sun gear drumBushing inner diameter (mm {in})Maximum 33.4 {1.31}Small sun gearBushing inner diameter (mm {in})Maximum 24.0 {0.945}Carrier hubClearance between pinion washer and planet carrier (mm {in})Maximum 0.20.7 {0.0080.028}Coasting clutchNumber of drive/driven plates 2/3Drive plate thickness (mm {in})Standard 1.6 {0.063}Maximum 1.5 {0.059}Coasting clutch clearance (mm {in}) 1.01.2 {0.0390.047}Snap ring size (mm {in})1.50 {0.059}, 1.65 {0.065}, 1.80 {0.071}, 1.95 {0.077},2.10 {0.083}, 2.25 {0.089}Reverse clutchNumber of drive/driven plates 2/2Drive plate thickness (mm {in})Standard 1.6 {0.063}Minimum 1.5 {0.059}Reverse clutch clearance (mm {in}) 1.51.8 {0.0590.070}Snap ring size (mm {in}) 2.0 {0.079}, 2.2 {0.087}, 2.4 {0.094}, 2.6 {0.102}, 2.8 {0.110}3-4 clutchNumber of drive/driven plates 4/4Drive plate thickness (mm {in})Standard 1.6 {0.063}Minimum 1.5 {0.059}3-4 clutch clearance (mm {in}) 1.31.5 {0.0510.059}Snap ring size (mm {in})3.80 {0.150}, 3.91 {0.154}, 4.04 {0.159}, 4.17 {0.164},4.30 {0.169}, 4.43 {0.174}, 4.56 {0.179}, 4.69 {0.185},4.80 {0.189}Low and reverse brakeNumber of drive/driven plates 4/4Drive plate thickness (mm {in})Standard 1.6 {0.063}Minimum 1.5 {0.059}Low and reverse brake clearance (mm {in})1.51.8 {0.0600.070}Snap ring size (mm {in}) 6.8 {0.268}, 7.0 {0.276}, 7.2 {0.283}, 7.4{0.291}, 7.6 {0.299}2-4 brake band Piston stem stroke (mm {in}) 0.81.2 {0.03940.0472}SERVICE TOOLS 05-6010505-60 SERVICE TOOLSTRANSMISSION/TRANSAXLE SST [GF4AX-EL] . . . . . . . . . . . . . . . . . . . . . .05-601TRANSMISSION/TRANSAXLE SST [LA4AX-EL (CD4E)] . . . . . . . . . . . . . . . . 05-603End of Tocautomatic transaxleTRANSMISSION/TRANSAXLE SST [GF4AX-EL]ezf05600000010149 0107 680AEngine stand49 0180 510BPreload measuring attachment49 0727 570Pinion height gauge body49 0839 425CBearing puller set49 8531 565Drive pinion model49 B017 209Attachment J49 F017 1A0Universal wrench49 F027 003Handle49 F027 005Attachment 6249 F207 007Attachment 7249 F401 331Body49 F401 337AAttachment C49 F401 366APlate49 FT01 361Bearing remover49 FT01 439Idler gear shaft holder49 G019 011Bearing installer49 G019 012Leak checker49 G019 013Bearing remover49 G019 017Oil seal installer49 G019 022Attachment K49 G019 0A0Transaxle hanger set
top related