application part - amp...
Post on 02-Sep-2018
219 Views
Preview:
TRANSCRIPT
rev 07.02.141/8www.amp-research.com
A S S E M B L Y & I N S T A L L A T I O N G U I D E
1
APPLICATION
Deep Bed Truck (F-150 & Tundra)Large Truck, Universal (Full-size trucks, wide beds)Small Truck, Universal (Mid-size and small trucks, small beds)
Remove contents from box and check for damage. Verify all parts against parts list. Read and understand instructions completely before attempting assembly and installation.
INSTALLATION TIME
SKILL LEVEL
1= Easy2 3 4
PART #
74813-00A (Silver) 74813-01A(Black) 74814-00A (Silver) 74814-01A(Black) 74811-00A (Silver) 74811-01A(Black)
TOOLS REQUIRED
Phillips screw driverTorx T-25 driverPower drill9/64” drill bitCenter punchSupplied templates Soapy Water
BEDXTENDER HD™ shown assembled and installed on truck.
1 Hour
Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents: 5,700,047; 6,113,173; 6,402,215; 6,805,392; 7,063,366; 7,393,035; 7,654,598; 7,681,935; 7,841,638
3-Year Limited WarrantyWARRANTY
rev 07.02.142/8www.amp-research.com
A M P R E S E A R C H B E D X T E N D E R H D ™
10 x2Strap latch insert Kit number 74603-01A
11 x2 Socket cap screw
(Only provided on Deep Bed/Small kits)
(Only provided on Deep Bed/Small kits)
PARTS LIST AND HARDWARE IDENTIFICATION
74608-01A Quick Mount Bracket Set
1 x220-01998-90 Phillips headscrew (included in 74608-01A)
2 x6 x4420-03654-90 Bumper
12-03791-24S (Small Silver) 12-03791-24SP (Small Silver with LOGO)12-03791-24B (Small Black) 12-03791-24BP (Small Black with LOGO)12-03791-28B (Large/Deep Black) 12-03791-28BP (Large/Deep Black with LOGO) 12-03791-28S (Large/Deep Silver) 12-03791-28SP (Large/Deep Silver with LOGO)
Center Tube
311-03639-90 PT-Screw
x12 x2520-01662-94Strap Buckle Assembly
6 x2Silver: 20-74811-00A (Small) Black: 20-74811-01A (Small) Silver: 20-74813-00A (Deep)Black: 20-74813-01A (Deep)Silver: 20-74814-00A (Large)Black: 20-74814-01A (Large)Pivot Upright Assembly
7 x220-3664B-90 (Small/Narrow) 20-3640B-90 (Large/Deep)
Bumper Upright Outer
8 x220-3664A-90 (Small/Narrow) 20-3640A-90 (Large/Deep)
Bumper Upright Inner
9 x3
rev 07.02.143/8www.amp-research.com
A M P R E S E A R C H B E D X T E N D E R H D ™
DESCRIPTION APPLICATION PART #
ADDITIONAL MOUNTING KITS No-Drill Mounting Bracket Kit – Ford F-Series
OPTIONAL
L-Bracket Mounting Kit
REQUIRED ON SOME APPLICATIONS TO COMPLETE INSTALLATION
10-74602-01A
10-74601-01A
2004+ F-150 2008+ F-250 2008+ F-350
GM S-Series Mazda B-Series Nissan Pickup Toyota Pickup (Pre 2005 models)
rev 07.02.144/8www.amp-research.com
A M P R E S E A R C H B E D X T E N D E R H D ™
UNIVERSAL MOUNTING BRACKET INSTALLATION
Cut out supplied template and tape to the D-pillar as shown. Using a center punch, mark holes as specified by the template.
Using a power drill and 9/64” drill bit, drill through the sheet metal. If equipped with a bedliner, drill through bedliner.
Fasten mounting brackets using the supplied self-tapping Phillips screws and torque to 30 in. lbs. If equipped with a bedliner, install mounting brackets over bedliner.
NOTE: If bedliner has contours that may prohibit a flat, solid mounting surface, cut out a rectan-gular section to clear the bracket and mount the bracket directly to the metal D-pillar.
2
1Phillips headscrew
2 x6
2
1
2
3
Quick Mount Bracket
1 x2
rev 07.02.145/8www.amp-research.com
A M P R E S E A R C H B E D X T E N D E R H D ™
BED X-TENDER ASSEMBLY
Adjust the width of the BEDXTENDER by placing the pivots into the mounting brackets. To keep overlap consant, adjust each tube so that the gap between the edge and the tape is the same.
1 2
3 4
Slide 3 center tubes into the open ends of the bent tubes as shown. Insert center tube with logo into the center tube.
Connect the two halves. Make sure there is at least 3” overlap with the bent tubes on each side.
Measure 7” from each end of the three center tubes and mark with tape. Tape is to be used as a refer-ence point
9
6
9
9 6
6
Note: Template located on inside of box.
rev 07.02.146/8www.amp-research.com
A M P R E S E A R C H B E D X T E N D E R H D ™
BED X-TENDER ASSEMBLY – CONTINUED
Adjust Strap Buckles to lock into the tailgate when BEDXTENDER is deployed. Your assembly is now complete.
7
9
8
Tighten PT-Screws using a T-25 torx driver, starting in the middle of each upright, then the outer screws and lastly the remaining two to evenly tighten.
3
8
7
NOTE: Do not over tighten as this may strip out. Fastener will reach a noticable stopping point.8
Attach plastic upright around the tube juncture, plac-ing rubber bumpers into the two ends of the upright.
NOTE: The inside of the upright is stepped to fit correctly around the small and large diameter tubes.
4
8
7 Upright is not positioned in center of tube joint.
rev 07.02.147/8www.amp-research.com
A M P R E S E A R C H B E D X - T E N D E R ™
Remove the PT-Screw with a T20 Torx driver.
1
A M P R E S E A R C H B E D X T E N D E R H D ™
Install Strap Buckle Insert with the provided 10/32 x 7mm socket head cap screw with a 4mm hex key. Repeat for other strap.
1110
For Toyota applications the supplied Strap Buckle Insert must be used.
10
11
12
When the BEDXTENDER is at the furthest rear position, push down on the buckle to insert into tailgate latch. Tighten straps. To release, pull tailgate handle.
NOTE: Ensure that buckles are properly inserted into latches by pulling on the straps after both buckles have been inserted.
rev 01.03.128/8www.amp-research.com
Congratulations on your purchase of the AMP Research BEDXTENDER HD.Here’s what you need know...
BEDXTENDER HD™ OPERATION
With the tailgate open, place BEDXTENDER pivot pins into the left and right mounting brackets. Rotate to 45 until it drops into place, then lower onto the open tailgate.
Flip BEDXTENDER out to contain cargo in the truck bed when the tailgate is open.CAUTION! 200lb maximum load on open tailgate. Always distribute cargo evenly and properly secure inside bed. Do not secure cargo to the BEDXTENDER or the tailgate.
Before driving, secure BEDXTENDER by locking the provided strap buckles into the truck’s tailgate latches. To release, pull tailgate handle. NOTE: Ensure that both buck-les are properly locked into the latches by pulling up on each strap.
Flip BEDXTENDER forward and close the tailgate to keep smaller cargo safe and organized.
LIMITED WARRANTY
1.28”
1.81”
1.3”
1.56”
6.7”
TRUCK BEDTRUCK BED
1.28”
1.81”
1.3”
1.56”
8”
Drill template for BEDXTENDER HD™ mounting brackets
NOTE: FOR TRUCKS WITH BEDLINERS, USE THIS TEMPLATEON TOP OF BEDLINER. DO NOT CUT BEDLINER!
Cut o
r fol
d al
ong
solid
line
s.
(Das
hed
lines
for t
ruck
s w
ith b
edlin
ers.
)
FACING REAR SIDE FOR LEFT BRACKET INSTALLATION FACI
NG R
EAR
SIDE
FOR
RIG
HT B
RACK
ET IN
STAL
LATI
ONUse dashed line for trucks with bedliners.
FACING REAR SIDE FOR LEFT BRACKET INSTALLATIONUse dashed line for trucks with bedliners.
FACI
NG R
EAR
SIDE
FOR
RIG
HT B
RACK
ET IN
STAL
LATI
ONUs
e da
shed
line
for t
ruck
s with
bed
liner
s.
Use
dash
ed lin
e fo
r tru
cks w
ith b
edlin
ers.
Drill
tem
plate
for B
EDXT
ENDE
R HD
™
mou
nting
bra
cket
s
top related