abudhabi conference jepl ppt

JAY ELSTOMER PVT. LTD.

How important is Role of a Roll In Colour Coating Industry A Presentation by

JAY ELASTOMERS PVT. LTD,INDIA

JAY ELASTOMERS PVT. LTD.

We divide this presentation in to 5 categories 1. Roll making consisting of -:

◊ Roll specifications◊ Roll drawings

◊ Roll fabrication ◊ Roll machining, finishing

◊ Roll balancing ◊ Roll inspection

JAY ELASTOMERS PVT. LTD. 2. Roll to be used for ‘TYPE’ of colour coating. ◊ Polyester Paints ◊ Varnishes ◊ Silicone Modified Polyester(SMP) ◊ Plastisols ◊ Epoxies ◊ Polyurethane ◊ PVDF ◊ Solvent free UV Curable

JAY ELASTOMERS PVT. LTD.

3. Roll may be covered with-: ◊Rubber-Natural ◊Rubber-Synthetic ◊ EPDM ◊ HYPOLON/CSM ◊ Polyurethane ◊ Chrome ◊ Plasma Coatings

JAY ELASTOMERS PVT. LTD.

4. Roll may be used to coat on-: ◊ Steel coil ◊ Sheet Metal ◊ Aluminium coil, foil ◊ Paper

JAY ELASTOMER PVT. LTD. 5. Rolls are used for Applications such as,-: ◊ Corrosion Protection ◊ Release Paper ◊ FDA Approved varnishing ◊ Can Coating, P P Cap making sheets ◊ Roofing Sheets ◊ Appliance Grade Coatings ◊ Car Body Coatings ◊ U V Curable Spreads

JAY ELASTOMER PVT. LTD. Section I The Roll performs best, if taken care while

making such as, -: 1. Roll drawing is with all revisions and up to date.

2. Roll fabricated in accordance with all specifications.

3. Roll is dynamically balanced at specified speed. 4. Roll is with appropriate sized drilled centres .

JAY ELASTOMER PVT. LTD.

5. Roll is having proper air escape passage.

6. Roll is with properly ground at bearing seat.

7. Roll is required to be fabricated with double flange design or with shrink fit method.

8. Roll is designed to take what Torque !

9. Roll can be used at what minimum shell thickness !

JAY ELASTOMER PVT. LTD.

Fitment of the shaft either shrink fit or double flangeWelded joints create imbalances.

• Flanges if not machined from both sides.

• Shrink fit shaft does not accommodate air escape

•Roll shaft centre and bearing seat finish not in alignment.

JAY ELASTOMER PVT. LTD.

JAY ELASTOMER PVT. LTD. Section Ii-:Various kinds of coatings are in use for Plastic films, Paper, Metal Foils and so on….. ►Adhesives ► Barrier Coats ► Anti Fungus/Anti Curl Coatings ► Sealable coatings ► Release Coatings ► Varnishes and Lacquers

JAY ELASTOMER PVT. LTD. Various Kind of Coating Methods are available-: 1. Gravure Coating 2. Comma Coating 3. Reverse Roll Coating 4. Hot Melt Coating 5. Metering Rod/Myer Bar Coating 6. Knife Over Roll Coating 7. Slot Orifice Coating 8. Immersion/Dip Coating 9. Curtain Coating

JAY ELASTOMERS PVT. LTD.

TYPICAL TWO-COAT PAINT SYSTEM

JAY ELASTOMER PVT. LTD.

Section Iii-: Roll covering material selection Hardness more than 60 Shore A

• Bridle Roller Polyurethane, Plasma Coated

• Pinch Roller polyurethane • Snubber Roller Polyurethane,CSM• Squeeze Roller CSM,Rubber,Polyurethane• Contact Roller Polyurethane, Rubber• Conveyor Roller Metal, Polyurethane

• Cradle Roller polyurethane, Rubber• Deflector Roller CSM, Polyurethane

JAY ELASTOMER PVT. LTD.

Coating roller covering material selection

Hardness less than 60 Shore A -:

• Applicator Roller – Rubber, Polyurethane• Squeeze Roller - Rubber, CSM,Polyurethane• Pickling line Roller – Rubber, Neoprene,• Metering Roller - Polyurethane• Pick up Roller - Rubber, Polyurethane

JAY ELASTOMER PVT. LTD.●CCL ‘s FAQ ‘S

1. Problems of roller covering getting sliced off

2. Roller covering swollen or with undulation over the surface.

3. Roller covering unsatisfactory to transfer uniform paint 4.Roller life is erratic with change of color coating system.

5. How to maintain a roller removed for grinding.

JAY ELASTOMER PVT. LTD.

6. When to grind the roller removed after coating activity

7. What rubber thickness is perfect to good color pick up

8. Standard acceptance norms for color coating line roller.

9. Specifications set for roller manufacturing

10.Unintentionally happened operational oversights

JAY ELASTOMER PVT. LTD.

Some typical problem leads misunderstanding

Coil thickness is in variation or Change in line speed or Change in angle of sheet passing over ,individually or together… ………can create additional torque, leading to compression of roller covering

Roller covering gets compressed leads to undulation of surface

Compressed surface gets crushed and smaller cracks develop with in surface

All remains unnoticed leads to fracture of surface and a small lump gets dislodged from surface

JAY ELASTOMER PVT. LTD.

Closer view

PARTICULAR PLACE TO RFLECT UNEVEN PRESSURE RESULTED DURING OPERATION.

JAY ELASTOMER PVT. LTD.

JAY ELASTOMER PVT. LTD.

A small section of roll covering gets extra load due to unequal tightening of pressure screws to adjust gap between Metal roll & coater roll,

Result…, polymer gets crushed…

ROLLER DAMAGE SEQUENCE

JAY ELASTOMER PVT. LTD.

Yellow patch showing undulation of surface

JAY ELASTOMER PVT. LTD.

Some More Observations-:

Roller covering soaks some amount of thinner or dilutant in the paint system employed and surface due to adsorption phenomenon goes soft.

Next if polymer has foreign particles, air pockets, flow marks, which may lead to tearing of soft polymer.

During coil change interface sheet is not fitted properly or Metal roller adjustment with coater roller not handled

properly and extra pressure gets exerted then at times only one side of coater roller shows damage.

.

Strips fitted imperfectly at interface

Jay Elastomers Pvt. Ltd. Section I V-:Substrate for colour coating is in accordance with application or end use.

Prepainted Steel Coil is widely used for, 1. Roofing sheets 2. Domestic or Industrial Appliances 3. Car body The level of asthetics,abrasion resistance, and flexibility is the essence of the requirement.

JAY ELASTOMERS PVT. LTD.

Prepainted Aluminium coil/foil is widely used for 1. Packaging. 2.Roffing Applications. 3.Smaller Appliances. 4.Composite Panels.

Aluminium being lighter and more ductile material requires special surface treatments before coating.

JAY ELASTOMERS PVT. LTD.

Varnishing is a typical application and usage 1. Sheets for can coating activity 2. Coating on Electrical grade steel 3. FDA approved coatings.•This process requires a typical oven curing system also coating are thinnest possible ranging from 15 micron to 80 micron.

•solvent based as well as water based coating are available.

JAY ELASTOMERS PVT.LTD. Section V-:• Recommendations for surface finishes, Rubber Roll Surface Finish to be define with Ra value and may be Application oriented.• To maintain required finish, Thinners and solvents used for cleaning must be certified.• Polar solvents may be avoided.• Surface finish also monitored for required kind of coating thickness• Type of coating with Solvents, solvent free or water based can also influence surface finish.

JAY ELASTOMERS PVT LTD. Recommendations for easy operations. 50+ hour formula1.Applicator roll is recommended to be used for max. 50+ hours to avoid swelling and softening of polymer surface.

2.Once used roll may be allowed to evaporate soaked Thinner/Solvents FOR 50+ hours, before taken for grinding.

3.Wet roller grinding is hazardous from fire and safety regulations point of view.

JAY ELASTOMERS PVT.LTD. Summery-:• Metal Roll making has become more subjective and precise. • Paint systems have grown from Polyester paints to PVDF and soon to enter aqueous coatings.

•Substrates changing from Steel coil to Aluminium foil, Release paper to can coating and currency note coatings •Oven curing to air drying, hot air blowing to UV Curing every stage change is observed.

JAY ELASTOMER PVT. LTD.• But, natural and synthetic rubbers are struggling to achieve

good-better-best .

• With changes in systems and conditions only conclusion can be drawn with present polymer coverings shall perform best if studied properly with respect to solvents, thinners, acidic solutions and line speeds.

• Here we conclude for best of coating technique to be explored further to make this presentation perfect .

THANK YOU !

JAY ELASTOMER PVT. LTD.