7 j electrical circuits (boardworks)
Post on 06-May-2015
2.197 Views
Preview:
TRANSCRIPT
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 20052 of 41
7J Electrical Circuits
Contents
Introducing circuits
Series circuits
Parallel circuits
Energy in circuits
Summary activities
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 20053 of 41
boilerand
pump
radiator
highpressure
lowpressure
flow ofwater
An electrical circuit is like a central heating system in a house.
There is a pump that pushes water around the system.
radiator
What is an electrical circuit?
The water everywhere starts to move at the same time.
There are pipes that carry the water.
In the pipes the water is flowing.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 20054 of 41
What is an electrical circuit?
Instead of a flow of water, electricity flows in an electrical circuit.
The electrical current is pushed by the cell (or battery), which has the same function as the pump and boiler. The strength of push provided by the battery is called its voltage.
The bulb in the circuit is like a radiator. An electrical device uses electrical energy supplied by the circuit.
The wires are like pipes; they carry the flow of electricity (called current) around the circuit.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 20056 of 41
7J Electrical Circuits
Contents
Introducing circuits
Series circuits
Parallel circuits
Energy in circuits
Summary activities
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 20057 of 41
This is a simple series circuit.
What is a series circuit?
In a simple series circuit, everything is connected in one loop across the terminals of the battery. So there aren’t any points where the current can split or join (these are called junctions).
This circuit has two lamps connected in series. Circuits are always drawn using straight lines.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 20058 of 41
Here are some other simple series circuits:
2. A rheostat (or variable resistor) and a bulb connected in series:
R1 R2
Examples of series circuits
1. Two resistances (resistors) connected in series:
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 20059 of 41
The unit of measure for current is the amp, which has the symbol A.
A
Measuring current
AA
Current is measured using a device called an ammeter. In a circuit diagram, an ammeter is shown by the symbol .
When measuring the current through a component, the ammeter is always connected in series (in the same loop) with that component.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200510 of 41
1
2
1. Set up the circuit as shown above.
R1
A
A
Experiment 1: Current in series circuit
Circuit 1
2. Measure the current using the ammeter at positions 1 and 2.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200511 of 41
3
1. Add another resistor into the circuit (R2) and another ammeter after it.
R1
A
A
A
R2
Experiment 1: Current in a series circuit
Circuit 2
1
2
2. Now measure the current using the ammeter at positions 1, 2 and 3.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200512 of 41
Circuit 2 results:
Current at position 1 =
Current at position 2 =
Current at position 3 =
Circuit 1 results:
Current at position 1 =
Current at position 2 =
Experiment 1: Current in a series circuit – results
R1A
A
Circuit 1 Circuit 2
R1 R2A
AA1
2
1
2
3
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200513 of 41
Experiment 1: Current in a series circuit – summary
Circuit 1The current at different positions in the circuit, before and after the resistor, was the _______.
Current is _____ used up by the components in the circuit.
Circuit 2Increasing the number of components in the circuit ________ the current.
The current at all points in a series circuit is the _______.
same / same / decreased / not
Circuit 1 Circuit 2
R1A
A R1 R2A
AA
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200514 of 41
When measuring the voltage across a component, the voltmeter is always connected in parallel with (or across) the component.
Voltage is measured using a device called a voltmeter. In a circuit diagram, a voltmeter is given the symbol . V
This is still a series circuit.
Measuring voltage
The voltage supplied by the battery is shared between allthe components in a series circuit.
V3
V2
V1
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200515 of 41
A
V
componenthere
Voltage is measured by connecting the voltmeter across (or in parallel with) the component.
V
Measuring voltage across a resistance or a bulb
R
Components
Voltage is measured in volts and the symbol for this is V.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200516 of 41
1. Set up the circuit as shown above.
R1
V
V
Circuit 1
Experiment 2: Voltage in a series circuit
2. Connect the voltmeter across the power supply (battery) and measure the supply voltage.
3. Then connect the voltmeter across the resistance (R) and measure this voltage.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200517 of 41
1. Add another resistor (R2) to the circuit as shown.
V2
Experiment 2: Voltage in a series circuit
Circuit 2
R1 R2
V
V1
2. Connect the voltmeter across the power supply (battery) and measure the supply voltage.
3. Then measure the voltage across each of the resistor.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200518 of 41
Circuit 1 results:
Voltage (supply) = V
Voltage (R1) = V
R1 R2
V
V1 V2
R1
V
V
Circuit 1 Circuit 2
Experiment 2: Voltage in a series circuit – results
Circuit 2 results:
Voltage (supply) = V
Voltage (R1) = V
Voltage (R2) = V
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200519 of 41
Experiment 2: Voltage in a series circuit – summary
The current is the _______ of electricity around the circuit. The _________ is the amount of push.
When two components were put into Circuit 2, the voltage of the supply was the _______ as Circuit 1. However, the voltage across R1 __________ .
The voltage across both components in Circuit 2 added to be equal to the ________ voltage.
R1 R2
V
V1 V2
R
V
V
Circuit 1 Circuit 2
supply / decreased / voltage / flow / same
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200520 of 41
1. Set up the circuit as shown above.
V
V
R A
Experiment 3: Cells in a series circuit
Circuit 1
2. Connect the voltmeter across the power supply (battery) and measure the supply voltage. Then measure the voltage across the resistance. Also measure the current.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200521 of 41
1. Add an additional battery to the circuit.
V
V
R A
Experiment 3: Cells in a series circuit
Circuit 2
2. Connect the voltmeter across the power supply and measure the supply voltage. Then measure the voltage across the resistance. Also measure the current.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200522 of 41
Circuit 1 results:
Supply voltage =
Voltage R =
Current =
Circuit 2 results:
Supply voltage =
Voltage R =
Current =
Experiment 3: Cells in a series circuit – results
R
V
V
A R
V
V
A
Circuit 1 Circuit 2
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200523 of 41
Experiment 3: Cells in a series circuit – summary
Delete the wrong answer:
Increasing the number of cells increases/decreases the current that flows in the circuit.
The current/voltage depends on the current/voltage.
Circuit 1 Circuit 2
R
V
V
A R
V
V
A
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200524 of 41
1. In a series circuit the current is the same in all parts of the circuit.
Series circuits – key ideas
2. The supply voltage is shared between the components in a series circuit. (The sum of the voltage across each component is the same as the total supply voltage.)
3. The current depends on the voltage in any circuit.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200526 of 41
7J Electrical Circuits
Contents
Introducing circuits
Series circuits
Parallel circuits
Energy in circuits
Summary activities
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200527 of 41
What is a parallel circuit?
A B
This means that there is more than one path around the circuit.
A parallel circuit is one which contains a point (a junction) where the current can split (point A) or join (point B).
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200528 of 41
A1
A2
A3
A4
1. Place the ammeter, in turn, at positions 1, 2, 3 and 4.
Measuring current in a parallel circuit
Ammeter Current (A)
A1
A2
A3
A4
2. Record the ammeter readings in the table.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200529 of 41
For a parallel circuit, the current that leaves the cell is the same as the current that returns to the cell.
Current in a parallel circuit
The current does not get used up by the circuit, just the energy that the electrons are carrying.
A1
A2
A3
A4
A1 = A4
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200530 of 41
The current splits up at the first junction and then joins together at the second junction.
Current in a parallel circuit
If the bulbs are identical then the current will split evenly.
The following is always true for this type of parallel circuit:A1
A2
A3
A4
A1 = (A2 + A3) = A4
If the bulbs are not identical, then the current will not split evenly.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200531 of 41
V2
Connect up this circuit and measure, in turn, the voltage at V1, V2 and V3. Record your results in the table.
Measuring voltage in a parallel circuit
What do you notice about the results?
How can you explain this?
Voltmeter Voltage(V)
V1
V2
V3
V1
V3
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200533 of 41
7J Electrical Circuits
Contents
Introducing circuits
Series circuits
Parallel circuits
Energy in circuits
Summary activities
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200534 of 41
Energy transfer in circuits
Energy cannot be created or destroyed.
In all devices and machines, including electric circuits, energy is transferred from one type to another.
When this circuit is connected, chemical energy stored in the battery is transferred via electrical energy to heat and light energy in the bulbs.
The total amount of heat and light energy is the same as the amount of chemical energy lost from the battery.
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200535 of 41
Most of the energy from the battery does not produce light – most of it is wasted as heat!
chemical energy from battery (e.g. 100J)
heat energy of bulb
95 J transferred to
5 J transferred to bulb as light energy
Energy transfer in electrical circuits
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200536 of 41
Batteries can power many electrical devices.
What sort of energy is electrical energy transferred into in these electrical devices?
What’s the energy transfer?
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200537 of 41
7J Electrical Circuits
Contents
Introducing circuits
Series circuits
Parallel circuits
Energy in circuits
Summary activities
© Boardworks Ltd 20041 of 20 © Boardworks Ltd 200538 of 41
Glossary
ammeter – A device that measures electric current.
circuit – A complete loop of conducting components that electricity flows around.
current – The flow of electricity, measured in amps (A).
parallel – A branched circuit – it has components connected on separate branches.
resistor – A component that makes it difficult for electricity to flow and so reduces the current.
series – A circuit without any branches – it has components connected in a row.
voltage – The amount of ‘push’ that a cell gives a circuit, measured in volts (V).
voltage – A device that measures voltage.
top related