6.75” ss100-b5 bicobrute - bico drilling tools, inc. · disclaimer: the performance curve and...

D

E

A

B

C

A - Bit to Center of Stabilizer Blade

B - Bit to Bend

C - Overall Motor Length

D - Max OD of Motor at Stabilizer Upset

E - Radius at Kickpad

Common Top Connection

Common Bottom Connection

Recommended Bit Sizes

Estimated Weight

22.7 in (577 mm)

53 in (1346 mm)

26.8 ft (8.2 m)

6.9 in (175.3 mm)

3.5 in (89 mm)

4-1/2 IF or XH

4-1/2 REG

7-7/8 in to 8-3/4 in (200 - 222.3 mm)

2900 lbs (1315 kg)

General Dimensional Data

6.75” SS100-B5www.bicodrilling.com

Lobes: 7/8

Motor Loads

*While Not OperatingContinuous Loads - Lay motor down if exceededUltimate Loads - Motor may part if exceeded

Power Section SpecificationsFlow Range

Speed Ratio

No Load Bit Speed

No Load Pressure Drop

200 - 600 gpm (757 - 2,271 lpm)

.28 rev/gal (.074 rev/l)

56 - 168 rpm

450 psi (31.02 bar)

Max Recommended Pressure

Torque Slope

Torque @ Max Recommended Pressure

Power @ Max Recommended Pressure

1,250 psi (86.2 bar)

9.75 ft-lb/psi (191.73 Nm/bar)

12,188 ft-lbs (16,524 Nm)

364 hp (272 kW)

180

135

90

45

0

16,000

12,000

8,000

4,000

012001000800600400200

Disclaimer: The Performance Curve and Performance Data published by BICO Drilling Tools are based on recorded dynamometer data at surface temperature (72 degF) on a standard fit configuration between rotor and stator, with clean water, and are presented as a reference to the potential power of the power section and or motor. Downhole conditions such as highly elevated bottom hole temperatures and different drilling/intervention fluids shall require adjusted loose fits that may produce reduced power during surface (dynamometer) testing and will achieve the expected torque and speed values when reaching planned conditions. Contact BICO for the adjusted performance curves.

Rated

Motor Differential Pressure (psi)

Bit S

peed

(rpm

)

Torq

ue (f

t-lbs

)

1400

600 GPM

400 GPM

200 GPM

Performance Curve

Ultimate LoadingContinuous Operation

WOB - lbs (kg)

Backreaming - lbs (kg)

Bit Overpull* - lbs (kg)

Body Overpull* - lbs (kg)

Slick Motor Hole Size (in)

Bend Angle

1.50

1.83

2.00

2.12

2.38

2.60

7-7/8

7.5

10.0

11.3

12.2

14.1

–

8-1/2

5.3

7.8

9.1

10.0

11.9

13.6

8-3/4

4.4

6.9

8.2

9.1

11.0

12.7

7-7/8

10.7

13.4

–

–

–

–

8-1/2

10.6

13.0

14.4

15.4

–

–

8-3/4

10.8

13.0

14.2

15.2

17.3

–

7-7/8

9.9

12.6

14.0

–

–

–

8-1/2

9.7

12.2

13.6

14.6

16.7

–

8-3/4

9.8

12.1

13.4

14.4

16.5

18.4

Stabilized 1/8” UG Hole Size (in) Stabilized 1/4” UG Hole Size (in)

Predicted Build Rates

*This condensed Build Rate table is the result of a theoretical geometry analysis of the motor and is presented as guideline for job design and planning. Due to the extensive variability in drilling BHA design, formation characteristics and other external factors, BICO cannot guarantee the values stated in the Build Rate table.

Degrees / 100 ft (30 m)

BICOBRUTERUGGED DEMANDS NO LESS

Motor: B5 Transmission: Articulated

–

–

740,000 (335,658)

1,070,000 (485,343)

60,000 (27,215)

29,000 (13,154)

197,000 (89,357)

526,000 (238,589)