20/138 technical specificationsapr 20, 2018 · section - 1 4 20/138sl technical specifications...
Post on 24-Sep-2020
3 Views
Preview:
TRANSCRIPT
IOWA MOLD TOOLING CO., INC.
P.O. Box 189Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com
20/138Technical
Specifications
Manual # 99904616
Revised 04-04-2017
Copyright © 2017 Iowa Mold Tooling Co., Inc.All rights reserved
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc.
Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company
ii
20/138 - Manual # 99904616
iii
20/138 - Manual # 99904616
Table of Contents
Section - 1 1
20/138SL Specifications.................................................................................................................................220/138SL Specifications - Continued .............................................................................................................320/138SL Specifications - Continued .............................................................................................................420/138SL Metric Specifications ......................................................................................................................520/138SL Metric Specifications - Continued ..................................................................................................620/138SL Metric Specifications - Continued ..................................................................................................7
Section - 2 9
20/138SL Lifting Capacity Chart, K2 ............................................................................................................1020/138SL Lifting Capacity Chart, K3 ............................................................................................................ 1120/138SL Lifting Capacity Chart, K4 ............................................................................................................1220/138SL Lifting Capacity Chart, K5 ............................................................................................................1320/138SL Lifting Capacity Chart, K6 ............................................................................................................1420/138SL Lifting Capacity Chart, K7 ............................................................................................................1520/138SL Lifting Capacity Chart, K8 ............................................................................................................1620/138SL Lifting Capacity Chart, K2 - K8 ....................................................................................................17
Section - 3 19
20/138SL - Pressure setting diagram, fixed flow pump & Danfoss RC ........................................................2020/138SL - Pressure setting diagram, variable flow pump & Danfoss RC ...................................................21Hydraulic Diagram - Danfoss, single-circuit fixed 6 fcts. RC (2 EXV: Grab + Rotator) ..............................................................................................................22Hydraulic Diagram - Danfoss, single-circuit variable 6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator) ...............................................................................23Hydraulic Diagram - Stabilizer circuit – 2 fcts. .............................................................................................24Hydraulic Diagram - Stabilizer circuit – 4 fcts. .............................................................................................25Hydraulic Diagram - Stabilizer circuit – 4 fcts. RC .......................................................................................26Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts..................................................................27Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts. RC ..........................................................28
Section - 4 31
20/138DL Specifications ..............................................................................................................................3220/138DL Specifications - Continued ...........................................................................................................3320/138DL Specifications - Continued ...........................................................................................................3420/138DL Metric Specifications ....................................................................................................................3520/138DL Metric Specifications - Continued ................................................................................................3620/138DL Metric Specifications - Continued ................................................................................................37
Section - 5 39
20/138DL Lifting Capacity Chart, K2 ............................................................................................................4020/138DL Lifting Capacity Chart, K3 ............................................................................................................4120/138DL Lifting Capacity Chart, K4 ............................................................................................................4220/138DL Lifting Capacity Chart, K5 ............................................................................................................4320/138DL Lifting Capacity Chart, K6 ............................................................................................................4420/138DL Lifting Capacity Chart, K7 ............................................................................................................4520/138DL Lifting Capacity Chart, K8 ............................................................................................................4620/138DL Lifting Capacity Chart, K2 - K8 ....................................................................................................47
iv
20/138 - Manual # 99904616
Section - 5 49
20/138DL - Pressure setting diagram, fixed flow pump & Danfoss RC........................................................5020/138DL - Pressure setting diagram, variable flow pump & Danfoss RC...................................................51Hydraulic Diagram - Danfoss, single-circuit fixed 6 fcts. RC (2 EXV: Grab + Rotator) ..............................................................................................................52Hydraulic Diagram - Danfoss, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch) .........................................................................................................53Hydraulic Diagram - Danfoss, single-circuit variable 6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator) ...............................................................................54Hydraulic Diagram - Danfoss, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch) .........................................................................................................55Hydraulic Diagram - Stabilizer circuit – 2 fcts. .............................................................................................56Hydraulic Diagram - Stabilizer circuit – 4 fcts. .............................................................................................57Hydraulic Diagram - Stabilizer circuit – 4 fcts. RC .......................................................................................58Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts..................................................................59Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts. RC ..........................................................60
Section - 6 63
Lifting capacity with winch ............................................................................................................................6420/138SL- Dimension sketch K2 - K6 ..........................................................................................................6520/138DL- Dimension sketch K2 - K6 ..........................................................................................................66Dimension sketch K7 - K8 ............................................................................................................................6720/138SL - Slewing Radius ..........................................................................................................................6820/138DL - Slewing Radius..........................................................................................................................69Dimension sketch for truck-mounted loader ................................................................................................7020/138SL - Lifting Height at Column ............................................................................................................7120/138DL - Lifting Height at Column ............................................................................................................72Dimension sketch, fixed stabilizer legs ........................................................................................................73Dimension sketch, fixed stabilizer legs ........................................................................................................74Dimension sketch, swing-up stabilizer legs 20°- 60° (manual) ....................................................................75Dimension sketch, swing-up stabilizer legs 20°- 60° (manual) ....................................................................76Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic) .......................................................77Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic) .......................................................7820/138SL - Dimension sketch, TS Top Seat (RC) ........................................................................................7920/138DL - Dimension sketch, TS Top Seat (RC) ........................................................................................8020/138SL - Dimension sketch, TS Top Seat (HC linear) ..............................................................................8120/138DL - Dimension sketch, TS Top Seat (HC linear) ..............................................................................8220/138SL - Dimension sketch, TS Top Seat (Danfoss X) ............................................................................8320/138DL - Dimension sketch, TS Top Seat (Danfoss X) ............................................................................8420/138SL - Dimension sketch, TS Top Seat (HC X) ....................................................................................8520/138DL - Dimension sketch, TS Top Seat (HC X) ....................................................................................8620/138SL - Dimension sketch, ladder for TS ...............................................................................................8720/138DL - Dimension sketch, ladder for TS ...............................................................................................88Technical data, winch ...................................................................................................................................89Dimension sketch, winch .............................................................................................................................90Dimension sketch, stand-up platform (std.) .................................................................................................91Dimension sketch, extra valves K7, K8 ........................................................................................................92Stowed in truck body ....................................................................................................................................9320/138SL - Centers of Gravity ......................................................................................................................9420/138DL - Centers of Gravity .....................................................................................................................95
This page left intentionally blank
v
20/138 - Manual # 99904616
This page left intentionally blank
vi
20/138 - Manual # 99904616
Section - 1 1 20/138SL Technical Specifications
20/138 - Manual # 99904616
Section - 120/138SL Technical Specifications
Section - 1 2 20/138SL Technical Specifications
20/138 - Manual # 99904616
20/138SL Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment ft-lb 140748 137145 121391 118766 115485 112861 110892Hydraulic reach ft 27’2’’ 33’8’’ 41’0’’ 48’6’’ 56’1’’ 63’4’’ 70’10’’Hydraulic telescopic movement ft 12’6” 19’1” 26’ 33’2” 40’7” 47’7” 54’10”
Lifting capacity, hydraulic
lb-ft 9920 - 14’4’’
9520 - 14’5’’
9125 - 14’9’’
8750 - 15’1’’
8395 - 15’1’
8045 - 15’5’’
7800 - 15’9’’
6830 - 20’4’’
6480 - 20’8’
6150 - 20’11’’
5820 - 20’11’’
5530 - 21’4’’
5225 - 21’8’’
5025 - 22’0’’
5180 - 26’11’’
4850 - 26’11’’
4495 - 27’3’’
4210 - 27’7’’
3945 - 27’10’’
3660 - 27’10’’
3480- 28’3’’
3880 - 33’6’’
3550 - 33’8’’
3260 - 34’1’’
2975 - 34’5’’
2710 - 34’5’’
2535 - 34’9’’
2910 - 40’8’’
2625 - 41’0’’
2360 - 41’4’’
2095 - 41’4’’
1915 - 41’8’’
2205 - 48’3’’
1940 - 48’7’’
1675 - 48’7’’
1500 - 48’10’’
1655 - 55’9’’
1390 - 56’1’’
1235 - 56’5’’
1210 - 62’11’’
1060 - 63’4’’950 - 70’6’’
Lifting capacity, manual extensions
lb-ft 2290 - 48’2’’
1740 - 56’1’’
1212 - 63’8’’
935 - 70’10’’
705 - 78’5’’
1850 - 56’1’’
1365 - 63’8’’ 990 - 71’2’’ 705 - 78’5’’
1455 - 63’8’’
1100 - 71’2’’ 715 - 79’0’’
Slewing torque, gross lb-ft 17553 17553 17553 17553 17553 17553 17553
Slewing angle ° 400 400 400 400 400 400 400Max. heel at max. load moment ° 5 5 5 5 5 5 5
Slewing speed °/s 24 24 24 24 24 24 24
Section - 1 3 20/138SL Technical Specifications
20/138 - Manual # 99904616
20/138SL Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis in 90 90 90 90 90 90 91Width in 98 98 98 98 98 98 98Length, no extra valves in 34 34 34 34 34 39 39Length, with extra valves (hose guides) in 39 39 39 39 39
Length, with 1 extra valve (hose reels) in 39 39
Length, with 2 extra valves (hose reels) in 40 40
Length, with extra valves (int. hose routing) in 34 34 34 34 34
Stabilizer spread, S1 (standard) ft 18’3” 18’3” 18’3” 18’3” 18’3” 18’3” 18’3”
Stabilizer spread, D ft 21’2” 21’2” 21’2” 21’2” 21’2” 21’2” 21’2”
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers lbs 3902 4244 4586 4894 5170 5401 5589
Stabilizers, S1 fixed lbs 606 606 606 606 606 606 606Stabilizers, S1 swing-up lbs 617 617 617 617 617 617 617Stabilizers, S1 hydr. swing-up lbs 628 628 628 628 628 628 628
Stabilizers, S2 fixed lbs 783 783 783 783 783 783 783Stabilizers, S2 swing-up lbs 783 783 783 783 783 783 783Stabilizers, S2 hydr. swing-up lbs 805 805 805 805 805 805 805
Stabilizers, D fixed lbs 143 143 143 143 143 143 143Stabilizers, D swing-up lbs 132 132 132 132 132 132 132Stabilizers, D hydr. swing-up lbs 99 99 99 99 99 99 99Mounting kit, 4 bolts lbs 176 154 132 99 77Mounting kit, 8 bolts lbs 154 132 99 77Tank, excl. oil (fitted on loader) lbs 132 99 77
Manual extensions lbs 77 88 99 110 121 132 143lbs 165 143 99 88lbs 143 99 88
Oil in loader (stowing position) lbs 66 77 88 99 110 110
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 4 20/138SL Technical Specifications
20/138 - Manual # 99904616
20/138SL Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K8Stand-up controls (HS), std. lbs 132 132 132 132 132 132 132Stand-up controls (HS), direct valve control lbs 154 154 154 154 154 154 154
Top seat (TS) lbs 198 198 198 198 198 198 198Top seat, ladder lbs 44 44 44 44 44 44 441 extra valve, hose guides lbs 121 143 165 187 2091 extra valve, hose reels lbs 209 2091 extra valve, int. hose routing lbs 165 165 176 176 1872 extra valves, hose guides lbs 165 198 231 265 2982 extra valves, hose reels lbs 408 4082 extra valves, int. hose routing lbs 287 287 309 320 331Winch (1.5 t), single snatch block lbs 386 386 386 386 397 397 419
Winch (1.5 t), double snatch block lbs 375 375 375 375 386 386 397
Winch (2.5 t), single snatch block lbs 441 441 441 441 452 452 463
Winch (2.5 t), double snatch block lbs 430 430 430 430 441 441 452
High-pressure filter lbs 15 15 15 15 15 15 15
Oil cooler lbs 55 55 55 55 55 55 55
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S1, fixed Lbf 24 24 24 24 24 24 24S1, swing-up Lbf 24 24 24 24 24 24 24S1, hydr. swing-up Lbf 24 24 24 24 24 24 24D, fixed Lbf 19 19 19 19 19 19 19D, swing-up Lbf 19 19 19 19 19 19 19D, hydr. swing-up Lbf 19 19 19 19 19 19 19
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure PSI 5003 5003 5003 5003 5003 5003 5003
Tank capacity (fitted on loader) Gal 23 23 23 23 23 23 23Max. pump performance, Hydrocontrol, 1-circuit Gpm 14 14 14 14 14 14 14
Max. pump performance, Hydrocontrol, 2-circuit Gpm - - - - - - -
Max. pump performance, Danfoss fixed flow Gpm 18 18 18 18 18 18 18
Max. pump performance, Danfoss variable Gpm 26 26 26 26 26 26 26
Section - 1 5 20/138SL Technical Specifications
20/138 - Manual # 99904616
20/138SL Metric Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment tm 19.5 19 18.5 18.1 17.6 17.2 16.9Hydraulic reach m 8.3 10.3 12.5 14.8 17.1 19.3 21.6Hydraulic telescopic movement mm 3830 5840 7930 10130 12370 14520 16720
Lifting capacity, hydraulic kg-m 4500 - 4.3 4320 - 4.4 4140 - 4.5 3970 - 4.6 3810 - 4.6 3650 - 4.7 3540 - 4.8
3100 - 6.2 2940 - 6.3 2790 - 6.4 2640 - 6.4 2510 - 6.5 2370 - 6.6 2280 - 6.7
2350 - 8.2 2200 - 8.2 2040 - 8.3 1910 - 8.4 1790 - 8.5 1660 - 8.5 1580 - 8.6
1760 - 10.2
1610 - 10.3
1480 - 10.4
1350 - 10.5
1230 - 10.5
1150 - 10.6
1320 - 12.4 1190 - 12.5 1070 -
12.6 950 - 12.6 870 - 12.7
1000 - 14.7 880 - 14.8 760 - 14.8 680 - 14.9
750 - 17.0 630 - 17.1 560 - 17.2
550 - 19.2 480 - 19.3
430 - 21.5
Lifting capacity, manual extensions
kg-m 1040 - 14.7 790 - 17.1 550 - 19.4 425 - 21.6 320 - 23.9
840 - 17.1 620 - 19.4 450 - 21.7 320 - 23.9660 - 19.4 500 - 21.7 325 - 24.1
Slewing torque, gross kNm 23.8 23.8 23.8 23.8 23.8 23.8 23.8
Slewing angle ° 400 400 400 400 400 400 400Max. heel at max. load moment ° 5 5 5 5 5 5 5
Slewing speed °/s 24 24 24 24 24 24 24
Section - 1 6 20/138SL Technical Specifications
20/138 - Manual # 99904616
20/138SL Metric Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis mm 2295 2295 2295 2295 2295 2295 2335Width mm 2500 2500 2500 2500 2500 2500 2500Length, no extra valves mm 885 885 885 885 885 995 995Length, with extra valves (hose guides) mm 1005 1005 1005 1005 1005
Length, with 1 extra valve (hose reels) mm 995 995
Length, with 2 extra valves (hose reels) mm 1030 1030
Length, with extra valves (int. hose routing) mm 885 885 885 885 885
Stabilizer spread, S1 (standard) mm 5575 5575 5575 5575 5575 5575 5575
Stabilizer spread, D mm 6455 6455 6455 6455 6455 6455 6455
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers kg 1770 1925 2080 2220 2345 2450 2535
Stabilizers, S1 fixed kg 275 275 275 275 275 275 275Stabilizers, S1 swing-up kg 280 280 280 280 280 280 280Stabilizers, S1 hydr. swing-up kg 285 285 285 285 285 285 285
Stabilizers, D fixed kg 355 355 355 355 355 355 355Stabilizers, D swing-up kg 355 355 355 355 355 355 355Stabilizers, D hydr. swing-up kg 365 365 365 365 365 365 365Mounting kit, 4-bolts kg 65 65 65 65 65 65 65Mounting kit, 8-bolts kg 60 60 60 60 60 60 60Tank, excl. oit (fitted on loader) kg 45 45 45 45 45 45 45
Manual extensions kg 80 70 60 45 35kg 70 60 45 35kg 60 45 35
Oil in loader (stowing position) kg 35 40 45 50 55 60 65
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 7 20/138SL Technical Specifications
20/138 - Manual # 99904616
20/138SL Metric Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K8Stand-up controls (HS), std. kg 60 60 60 60 60 60 60Stand-up controls (HS), direct valve control kg 70 70 70 70 70 70 70
Top seat (TS) kg 90 90 90 90 90 90 90Top seat, ladder kg 20 20 20 20 20 20 201 extra valve, hose guides kg 55 65 75 85 951 extra valve, hose reels kg 95 951 extra valve, int. hose routing kg 75 75 80 80 852 extra valves, hose guides kg 75 90 105 120 1352 extra valves, hose reels kg 185 1852 extra valves, int. hose routing kg 130 130 140 145 150Winch (1.5 t), single snatch block kg 175 175 175 175 180 180 190
Winch (1.5 t), double snatch block kg 170 170 170 170 175 175 180
Winch (2.5 t), single snatch block kg 200 200 200 200 205 205 210
Winch (2.5 t), double snatch block kg 195 195 195 195 200 200 205
High-pressure filter 7 7 7 7 7 7 7
Oil cooler 25 25 25 25 25 25 25
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S1, fixed kN 110 110 110 110 110 110 110S1, swing-up kN 110 110 110 110 110 110 110S1, hydr. swing-up kN 110 110 110 110 110 110 110D, fixed kN 85 85 85 85 85 85 85D, swing-up kN 85 85 85 85 85 85 85D, hydr. swing-up kN 85 85 85 85 85 85 85
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure Bar 345 345 345 345 345 345 345
Tank capacity (fitted on loader) L 90 90 90 90 90 90 90Max. pump performance, Hydrocontrol, 1-circuit L/min 55 55 55 55 55 55 55
Max. pump performance, Hydrocontrol, 2-circuit L/min - - - - - - -
Max. pump performance, Danfoss fixed flow L/min 70 70 70 70 70 70 70
Max. pump performance, Danfoss variable L/min 100 100 100 100 100 100 100
This page left intentionally blank
8
20/138 - Manual # 99904616
Section - 2 9 20/138SL Load Capacity Charts
20/138 - Manual # 99904616
Section - 220/138SL Load Capacity Charts
Section - 2 10 20/138SL Load Capacity Charts
20/138 - Manual # 99904616
20/138SL Lifting Capacity Chart, K2
70399837
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138SL K2
03'
6'9'
12'15'
18'21'
24'CENTERLINE
(0.91m)
(1.83m)
(2.74m)
(3.66m)
(4.57m)
(5.49m)
(6.40m) (8.23m)
(7.32m)27'
0MOUNTINGSURFACE
(0.91m)
6'(1.83m)
9'(2.74m)
12'(3.66m)
15'(4.57m)
18'(5.49m)
21'(6.40m)
24'(7.32m)
27'(8.23m)
30'(9.14m)
33'(10.06m)
3'
KGLB
99204500
68303100
162007350
51802350
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 11 20/138SL Load Capacity Charts
20/138 - Manual # 99904616
20/138SL Lifting Capacity Chart, K3
70399838
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138SL K3
0CENTERLINE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
3'(0.91m)
9'(2.74m)
15'(4.57m)
21'(6.40m)
27'(8.23m)
33'(10.06m)
MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
0
95204320
64802940
153606970
48502200
38801760
KGLB
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 12 20/138SL Load Capacity Charts
20/138 - Manual # 99904616
20/138SL Lifting Capacity Chart, K4
70399839
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138SL K4
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
91254140
61502790
145456600
44952040
35501610
29101320
KGLB
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 13 20/138SL Load Capacity Charts
20/138 - Manual # 99904616
20/138SL Lifting Capacity Chart, K5
70399840
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138SL K5
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)KG
LB
87503970
58202640
137756250
42101910
32601480
26251190
22051000
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 14 20/138SL Load Capacity Charts
20/138 - Manual # 99904616
20/138SL Lifting Capacity Chart, K6
70399841
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138SL K6
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
KGLB
83953810
55302510
135556150
39451790
29751350
23601070
1940880
1655750
91454150
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 15 20/138SL Load Capacity Charts
20/138 - Manual # 99904616
20/138SL Lifting Capacity Chart, K7
70399842
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138SL K7
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)57'
60'(18.29m)
(17.37m)63'
(19.20m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
52252370
36601660
128505830
27101230
2095 950
1675760
1390630
1210550
80453650
KGLB
91454150
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 16 20/138SL Load Capacity Charts
20/138 - Manual # 99904616
20/138SL Lifting Capacity Chart, K8
70399843
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138SL K8
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)57'
60'(18.29m)
(17.37m)63'
(19.20m)
66'
69'(20.03m)
(20.12m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
72'(21.95m)
78'(23.77m)
KGLB
50252280
34801580
123005580
25351150
1915 870
1500680
1060480
950430
78003540
1235560
91454150
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 17 20/138SL Load Capacity Charts
20/138 - Manual # 99904616
20/138SL Lifting Capacity Chart, K2 - K8
Lift ing capa city wi thout manual extension sLift ing capa city wi th manual extension s
K8
lbsft
780015'9"
502522’0”
348028'3"
253534'9"
191541'8"
150048’10”
123556'5"
106063'4"
95070'6"
70578'5"
K7
lbsft
804515'5"
522521'8"
366027’10”
271034'5"
209541'4"
167548'7"
139056'1"
121062’11”
93570’10”
70578'5"
K6
lbsft
839515'1"
553021'4"
394527’10”
297534'5"
236041'4"
194048'7"
165555'9"
121063'8"
99071'2"
71579’
K5
lbsft
875015'1"
582020’11”
421027'7"
326034'1"
262514’
220548'3"
174056'1"
136563'8"
110071'2"
K4
lbsft
912514'9"
615020’11”
449527'3"
355033’8”
291040'8"
229048’2”
185056'1"
145563'8"
K3
lbsft
952014'5"
648020'8"
485026’11”
388033'6"
K2
lbsft
992014'4"
683020'4"
518026’11”
kgm
kgm
kgm
kgm
kgm
kgm
kgm
45004.3
31006.2
23508.2
43204.4
29406.3
22008.2
176010.2
4140 4.5
27906.4
20408.3
161010.3
132012.4
104014.7
84017.1
66019.4
39704.6
26406.4
19108.4
148010.4
119012.5
100014.7
62019.4
50021.7
38104.6
25106.5
17908.5
135010.5
107012.6
88014.8
75017.0
55019.4
45021.7
32524.1
36504.7
23706.6
16608.5
123010.5
95012.6
76014.8
63017.1
55019.2
42521.6
32023.9
35404.8 6.7 19.3 21.5
2280 15808.6
115010.6
87012.7
68014.9
56017.2
480 430 32023.9
79017.1
This page left intentionally blank
18
20/138 - Manual # 99904616
Section - 3 19 20/138SL Hydraulics
20/138 - Manual # 99904616
Section - 320/138SL Hydraulics
Section - 3 20 20/138SL Hydraulics
20/138 - Manual # 99904616
20/138SL - Pressure setting diagram, fixed flow pump & Danfoss RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 345 5004
Slewing systemRight A P 180 P 2611Left B P 180 P 2611
Boom cylinderDown A 125 100 1813 1450Up B 350 380 5076 5511
Jib cylinderUp A 350 380 5076 5511Down B 250 230 3626 3336
Extension cylindersExtend A P - P -Retract B P - P -
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 185 2683Left 185 2683
Boom cylinderUp 365 5294
Down - -
Jib cylinderUp 380 5511
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 330 [bar] 4786 [PSI]HDL 285 [bar] 4134 [PSI]
Max. pump performanceChoice of pump 1 x Fixed 1 x FixedPump performance 70 L/min 18.5 gpm
IMT reserves the right to introduce improvements and modifications
Section - 3 21 20/138SL Hydraulics
20/138 - Manual # 99904616
20/138SL - Pressure setting diagram, variable flow pump & Danfoss RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 345 5004
Slewing systemRight A P 180 P 2611Left B P 180 P 2611
Boom cylinderDown A 125 100 1813 1450Up B 350 380 5076 5511
Jib cylinderUp A 350 380 5076 5511Down B 250 230 3626 3336
Extension cylindersExtend A P 300 P 4351Retract B P 300 P 4351
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 185 2683Left 185 2683
Boom cylinderUp 365 5294
Down - -
Jib cylinderUp 380 5511
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 330 [bar] 4786 [PSI]HDL 285 [bar] 4134 [PSI]
Max. pump performanceChoice of pump 1 x Variable 1 x VariablePump performance 100 L/min 26.4 gpm
IMT reserves the right to introduce improvements and modifications
Section - 3 22 20/138SL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Danfoss, single-circuit fixed 6 fcts. RC (2 EXV: Grab + Rotator)
Option
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
P PVSK
HPCO
63093/63302/63304/63319
X4
X1
X2
X3
Pst
Tst PVP
T
P
LS M
A-PORTA1
B1
A-PORTA2
B2
A-PORTA3
B3
A-PORTA4
B4
A-PORTA5
B5
A-PORTA6
B6
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
4940
1
Section - 3 23 20/138SL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Danfoss, single-circuit variable 6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator)
Option
Recommended
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
PVP
T
P
LS M
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
A-PORTA6
B6
A-PORTA5
B5
A-PORTA4
B4
A3
B3
A-PORT
A-PORTA2
B2
A-PORTA1
B1
63092/63301/63303/63313
P PVSKPst
Tst
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
4940
1
Section - 3 24 20/138SL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 2 fcts.
PstTst
A-PORT
A2 B2
A-PORT
A1 B1
5522
5
PT
5849
6
5849
6
Section - 3 25 20/138SL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 4 fcts.
PstTst
D
C
5522
8
5849
6
5849
6
D
C
5522
8
A14 B14 A13 B13 A12 B12 A11 B11
5522
6 / 5
5281
PT
A-PORT A-PORT A-PORTA-PORT
Section - 3 26 20/138SL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 4 fcts. RC
D
C
5522
8
5849
6
5849
6
D
C
5522
8
PstTst
A13 B13 A12 B12
5527
6
T
B-PORT
A-PORT
A11 B11
PA-PORT
B-PORT
NEM-MODULPT
T
ø1 mmø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
49187
49187
Only when HR stabilizer
Section - 3 27 20/138SL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts.
D
C
5522
8
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
A15 B15 A14 B14 A13 B13 A12 B12
5527
7
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
PA-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Section - 3 28 20/138SL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts. RC
D
C55
228
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
P
P
A15 B15 A14 B14 A13 B13 A12 B12
5527
5
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
A-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
NEM-MODULT
T
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Only when HR stabilizer
49187
49187
This page left intentionally blank
29
20/138 - Manual # 99904616
This page left intentionally blank
30
20/138 - Manual # 99904616
Section - 4 31 20/138DL Technical Specifications
20/138 - Manual # 99904616
Section - 420/138DL Technical Specifications
Section - 4 32 20/138DL Technical Specifications
20/138 - Manual # 99904616
20/138DL Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment ft-lb 140748 137867 134258 130649 127762 124153 122709Hydraulic reach ft 27’2’’ 33’8’’ 41’0’’ 48’6’’ 56’1’’ 63’4’’ 70’10’’Hydraulic telescopic movement ft 12’6” 19’2” 26’1” 33’2” 40’7” 47’7” 54’10”
Lifting capacity, hydraulic lb-ft 9940 -
14’1’’9545 - 14’5’’
9145 - 14’8’’
8770 - 15’0’’
8420 - 15’0’’
8065 - 15’5’’
7825 - 15’9’’
6855 - 20’4’’
6500 - 20’’8’
6150 - 20’11’’
5840 - 20’11’’
5530 - 21’4’’
5245 - 21’8’’
5045 - 21’11’’
5200 - 26’11’’
4850 - 26’11’’
4520 - 27’2’’
4230 - 27’6’’
3945 - 27’10’’
3680 - 27’10’’
3505 - 28’3’’
3880 - 33’5’’
3550 - 33’8’’
3260 - 34’1’’
2995 - 34’5’’
2710 - 34’5’’
2555 - 34’8’’
2930 - 40’7’’
2625 - 41’0’’
2360 - 41’4’’
2095 - 41’4’’
1940 - 41’8’’
2205 - 48’2’’
1940 - 48’6’’
1675 - 48’6’’
1520 - 48’10’’
1655 - 55’8’’
1390 - 56’1’’
1235 - 56’5’’
1210 - 62’11’’
1060 - 63’4’’950 - 70’6’’
Lifting capacity, manual extensions lb-ft 2290 -
48’2’’1740 - 56’1’’
1210 - 63’7’’
936 - 70’10’’
705 - 78’5’’
1850 - 56’1’’
1365 - 63’7’’ 990 - 71’1’’ 705 - 78’5’’
1455 - 63’7’’
1100 - 71’1’’ 715 - 79’0’’
Slewing torque, gross lb-ft 17553 17553 17553 17553 17553 17553 17553
Slewing angle ° 400 400 400 400 400 400 400Max. heel at max. load moment ° 5 5 5 5 5 5 5
Slewing speed °/s 24 24 24 24 24 24 24
Section - 4 33 20/138DL Technical Specifications
20/138 - Manual # 99904616
20/138DL Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis in 90 90 90 90 90 90 91Width in 98 98 98 98 98 98 98Length, no extra valves in 34 34 34 34 34 39 39Length, with extra valves (hose guides) in 39 39 39 39 39
Length, with 1 extra valve (hose reels) in 39 39
Length, with 2 extra valves (hose reels) in 40 40
Length, with extra valves (int. hose routing) in 34 34 34 34 34
Stabilizer spread, S1 (standard) ft 18’3” 18’3” 18’3” 18’3” 18’3” 18’3” 18’3”
Stabilizer spread, D ft 21’2” 21’2” 21’2” 21’2” 21’2” 21’2” 21’2”
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers lbs 4057 4398 4806 5115 5390 5622 5809
Stabilizers, S1 fixed lbs 606 606 606 606 606 606 606
Stabilizers, S1 swing-up lbs 617 617 617 617 617 617 617Stabilizers, S1 hydr. swing-up lbs 628 628 628 628 628 628 628
Stabilizers, D fixed lbs 783 783 783 783 783 783 783Stabilizers, D swing-up lbs 783 783 783 783 783 783 783Stabilizers, D hydr. swing-up lbs 805 805 805 805 805 805 805
Mounting kit, 4 bolts lbs 143 143 143 143 143 143 143Mounting kit, 8 bolts lbs 132 132 132 132 132 132 132Tank, excl. oil (fitted on loader) lbs 99 99 99 99 99 99 99
Manual extensions lbs 176 154 132 77 77lbs 154 132 99 77lbs 132 99 77
Oil in loader (stowing position) lbs 88 99 110 121 132 143 143
lbs 165 143 99 88lbs 143 99 88
Oil in loader (stowing position) lbs 66 77 88 99 110 110
Section - 4 34 20/138DL Technical Specifications
20/138 - Manual # 99904616
20/138DL Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K8Stand-up controls (HS), std. lbs 132 132 132 132 132 132 132Stand-up controls (HS), direct valve control lbs 154 154 154 154 154 154 154
Top seat (TS) lbs 198 198 198 198 198 198 198Top seat, ladder lbs 44 44 44 44 44 44 441 extra valve, hose guides lbs 121 143 165 187 2091 extra valve, hose reels lbs 209 2091 extra valve, int. hose routing lbs 165 165 176 176 1872 extra valves, hose guides lbs 165 198 231 265 2982 extra valves, hose reels lbs 408 4082 extra valves, int. hose routing lbs 287 287 309 320 331Winch (1.5 t), single snatch block lbs 386 386 386 386 397 397 419
Winch (1.5 t), double snatch block lbs 375 375 375 375 386 386 397
Winch (2.5 t), single snatch block lbs 441 441 441 441 452 452 463
Winch (2.5 t), double snatch block lbs 430 430 430 430 441 441 452
High-pressure filter lbs 15 15 15 15 15 15 15
Oil cooler lbs 55 55 55 55 55 55 55
1) Weights ± 5% because of tolerances for plate thickness
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S1, fixed Lbf 24 24 24 24 24 24 24S1, swing-up Lbf 24 24 24 24 24 24 24S1, hydr. swing-up Lbf 24 24 24 24 24 24 24D, fixed Lbf 19 19 19 19 19 19 19D, swing-up Lbf 19 19 19 19 19 19 19D, hydr. swing-up Lbf 19 19 19 19 19 19 19
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure PSI 5003 5003 5003 5003 5003 5003 5003
Tank capacity (fitted on loader) Gal 23 23 23 23 23 23 23Max. pump performance, Hydrocontrol, 1-circuit Gpm 14 14 14 14 14 14 14
Max. pump performance, Hydrocontrol, 2-circuit Gpm - - - - - - -
Max. pump performance, Danfoss fixed flow Gpm 18 18 18 18 18 18 18
Max. pump performance, Danfoss variable Gpm 26 26 26 26 26 26 26
Section - 4 35 20/138DL Technical Specifications
20/138 - Manual # 99904616
20/138DL Metric Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment tm 19.5 19.1 18.6 18.1 17.7 17.2 17Hydraulic reach m 8.3 10.3 12.5 14.8 17.1 19.3 21.6Hydraulic telescopic movement mm 3830 5840 7930 10130 12370 14520 16720
Lifting capacity, hydraulic kg-m 4510 - 4.3 4330 - 4.4 4150 - 4.5 3980 - 4.6 3820 - 4.6 3660 - 4.7 3550 - 4.8
3110 - 6.2 2950 - 6.3 2790 - 6.4 2650 - 6.4 2510 - 6.5 2380 - 6.6 2290 - 6.7
2360 - 8.2 2200 - 8.2 2050 - 8.3 1920 - 8.4 1790 - 8.5 1670 - 8.5 1590 - 8.6
1760 - 10.2
1610 - 10.3
1480 - 10.4
1360 - 10.5
1230 - 10.5
1160 - 10.6
1330 - 12.4 1190 - 12.5 1070 -
12.6 950 - 12.6 880 - 12.7
1000 - 14.7 880 - 14.8 760 - 14.8 690 - 14.9
750 - 17.0 630 - 17.1 560 - 17.2
550 - 19.2 480 - 19.3
430 - 21.5
Lifting capacity, manual extensions
kg-m 1040 - 14.9 790 - 17.1 550 - 19.4 425 - 21.6 320 - 23.9
840 - 17.1 620 - 19.4 450 - 21.7 320 - 23.9660 - 19.4 500 - 21.7 325 - 24.1
Slewing torque, gross kNm 23.8 23.8 23.8 23.8 23.8 23.8 23.8
Slewing angle ° 400 400 400 400 400 400 400Max. heel at max. load moment ° 5 5 5 5 5 5 5
Slewing speed °/s 24 24 24 24 24 24 24
Section - 4 36 20/138DL Technical Specifications
20/138 - Manual # 99904616
20/138DL Metric Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis mm 2295 2295 2295 2295 2295 2295 2335Width mm 2500 2500 2500 2500 2500 2500 2500Length, no extra valves mm 885 885 885 885 885 995 995Length, with extra valves (hose guides) mm 1005 1005 1005 1005 1005
Length, with 1 extra valve (hose reels) mm 995 995
Length, with 2 extra valves (hose reels) mm 1030 1030
Length, with extra valves (int. hose routing) mm 885 885 885 885 885
Stabilizer spread, S1 (standard) mm 5575 5575 5575 5575 5575 5575 5575
Stabilizer spread, D mm 6455 6455 6455 6455 6455 6455 6455
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers kg 1840 1995 2180 2320 2445 2550 2635
Stabilizers, S1 fixed kg 275 275 275 275 275 275 275
Stabilizers, S1 swing-up kg 280 280 280 280 280 280 280Stabilizers, S1 hydr. swing-up kg 285 285 285 285 285 285 285
Stabilizers, D fixed kg 355 355 355 355 355 355 355Stabilizers, D swing-up kg 355 355 355 355 355 355 355Stabilizers, D hydr. swing-up kg 365 365 365 365 365 365 365
Mounting kit, 4 bolts kg 65 65 65 65 65 65 65Mounting kit, 8 bolts kg 60 60 60 60 60 60 60Tank, excl. oil (fitted on loader) kg 45 45 45 45 45 45 45
Manual extensions kg 80 70 60 35 35kg 70 60 45 35kg 60 45 35
Oil in loader (stowing position) kg 40 45 50 55 60 65 65
kg 75 65 45 40kg 65 45 40
Oil in loader (stowing position) kg 30 35 40 45 50 50
Section - 4 37 20/138DL Technical Specifications
20/138 - Manual # 99904616
20/138DL Metric Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K8Stand-up controls (HS), std. kg 60 60 60 60 60 60 60Stand-up controls (HS), direct valve control kg 70 70 70 70 70 70 70
Top seat (TS) kg 90 90 90 90 90 90 90Top seat, ladder kg 20 20 20 20 20 20 201 extra valve, hose guides kg 55 65 75 85 951 extra valve, hose reels kg 95 951 extra valve, int. hose routing kg 75 75 80 80 852 extra valves, hose guides kg 75 90 105 120 1352 extra valves, hose reels kg 185 1852 extra valves, int. hose routing kg 130 130 140 145 150Winch (1.5 t), single snatch block kg 175 175 175 175 180 180 190
Winch (1.5 t), double snatch block kg 170 170 170 170 175 175 180
Winch (2.5 t), single snatch block kg 200 200 200 200 205 205 210
Winch (2.5 t), double snatch block kg 195 195 195 195 200 200 205
High-pressure filter kg 7 7 7 7 7 7 7
Oil cooler kg 25 25 25 25 25 25 25
1) Weights ± 5% because of tolerances for plate thickness
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S1, fixed kN 110 110 110 110 110 110 110S1, swing-up kN 110 110 110 110 110 110 110S1, hydr. swing-up kN 110 110 110 110 110 110 110D, fixed kN 85 85 85 85 85 85 85D, swing-up kN 85 85 85 85 85 85 85D, hydr. swing-up kN 85 85 85 85 85 85 85
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure Bar 345 345 345 345 345 345 345
Tank capacity (fitted on loader) L 90 90 90 90 90 90 90Max. pump performance, Hydrocontrol, 1-circuit L/min 55 55 55 55 55 55 55
Max. pump performance, Hydrocontrol, 2-circuit L/min - - - - - - -
Max. pump performance, Danfoss fixed flow L/min 70 70 70 70 70 70 70
Max. pump performance, Danfoss variable L/min 100 100 100 100 100 100 100
This page left intentionally blank
38
20/138 - Manual # 99904616
Section - 5 39 20/138DL Load Capacity Charts
20/138 - Manual # 99904616
Section - 520/138DL Load Capacity Charts
Section - 5 40 20/138DL Load Capacity Charts
20/138 - Manual # 99904616
20/138DL Lifting Capacity Chart, K2
70399830
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138DL K2
03'
6'9'
12'15'
18'21'
24'CENTERLINE
(0.91m)
(1.83m)
(2.74m)
(3.66m)
(4.57m)
(5.49m)
(6.40m) (8.23m)
(7.32m)27'
0MOUNTINGSURFACE
(0.91m)
6'(1.83m)
9'(2.74m)
12'(3.66m)
15'(4.57m)
18'(5.49m)
21'(6.40m)
24'(7.32m)
27'(8.23m)
30'(9.14m)
33'(10.06m)
3'
KGLB
99404510
68553110
162657380
52002360
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 5 41 20/138DL Load Capacity Charts
20/138 - Manual # 99904616
20/138DL Lifting Capacity Chart, K3
70399831
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138DL K3
0CENTERLINE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
3'(0.91m)
9'(2.74m)
15'(4.57m)
21'(6.40m)
27'(8.23m)
33'(10.06m)
MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
0
95454330
65002950
155807070
48502200
38801760
KGLB
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 5 42 20/138DL Load Capacity Charts
20/138 - Manual # 99904616
20/138DL Lifting Capacity Chart, K4
70399832
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138DL K4
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
91454150
61502790
149206770
45202050
35501610
29301330
KGLB
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 5 43 20/138DL Load Capacity Charts
20/138 - Manual # 99904616
20/138DL Lifting Capacity Chart, K5
70399833
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138DL K5
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
KGLB
87703980
58402650
143256500
42301920
32601480
26251190
22051000
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 5 44 20/138DL Load Capacity Charts
20/138 - Manual # 99904616
20/138DL Lifting Capacity Chart, K6
70399834
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138DL K6
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
KGLB
84203820
55302510
137556240
39451790
29951360
23601070
1940880
1655750
136856210
91454150
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 5 45 20/138DL Load Capacity Charts
20/138 - Manual # 99904616
20/138DL Lifting Capacity Chart, K7
70399835
REVISIONS
REV ECO DESCRIPTION DATE BYNOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70399835
CAPACITY CHART20/138DL K7
5-15-15IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
OJR
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138DL K7
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)57'
60'(18.29m)
(17.37m)63'
(19.20m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
52452380
36801670
132005990
27101230
2095 950
1675760
1390630
1210550
80653660
KGLB
136856210
91454150
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 5 46 20/138DL Load Capacity Charts
20/138 - Manual # 99904616
20/138DL Lifting Capacity Chart, K8
70399836
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model20/138DL K8
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)57'
60'(18.29m)
(17.37m)63'
(19.20m)
66'
69'(20.03m)
(20.12m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
72'(21.95m)
78'(23.77m)
KGLB
50452290
35051590
127405780
25551160
1940 880
1520690
1060480
950430
78253550
136856210
1235560
91454150
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Lifting capacity without manual extensionsLifting capacity with manual extensions
K8
lbsft
782515'9"
504521’11”
350528'3"
255534'9"
194041'8"
152048’10”
123556'5"
106063'4"
95070'6"
70578'5"
K7
lbsft
806515'5"
524521'8"
368027’10”
271034'5"
209541'4"
167548'6"
139056'1"
121062’11”
93570’10”
70578'5"
K6
lbsft
842015'0"
553021'4"
394527’10”
299534'5"
236041'4"
194048'6"
165555'8"
121063'7"
99071'1"
71579’0”
K5
lbsft
877015'0"
584020’11”
423027'6"
326034'1"
262514’0”
220548'2"
174056'1"
136563'7"
110071'1"
K4
lbsft
914514'8"
615020’11”
452027'2"
355033’8”
293040'7"
229048’2”
185056'1"
145563'7"
K3
lbsft
954514'5"
650020'8"
485026’11”
388033'5"
K2
lbsft
994014'1"
685520'4"
520026’11”
kgm
45104.3
31106.2
23608.2
kgm
43304.4
29506.3
22008.2
176010.2
66019.4
62019.4
50021.7
kgm
41504.5
27906.4
20508.3
kgm
39804.6
26506.4
19208.4
kgm
38204.6
25106.5
17908.5
kgm
36604.7
23806.6
16708.5
kgm
35504.8
22906.7
15908.6
116010.6
88012.7
69014.9
56017.2
48019.3
43021.5
32023.9
123010.5
95012.6
76014.8
63017.1
55019.2
42521.6
32023.9
136010.5
107012.6
88014.8
75017.0
55019.4
45021.7
32524.1
148010.4
119012.5
100014.7
79017.1
161010.3
133012.4
104014.9
84017.1
Section - 5 47 20/138DL Load Capacity Charts
20/138 - Manual # 99904616
20/138DL Lifting Capacity Chart, K2 - K8
Lifting capacity without manual extensionsLifting capacity with manual extensions
K8
lbsft
782515'9"
504521’11”
350528'3"
255534'9"
194041'8"
152048’10”
123556'5"
106063'4"
95070'6"
70578'5"
K7
lbsft
806515'5"
524521'8"
368027’10”
271034'5"
209541'4"
167548'6"
139056'1"
121062’11”
93570’10”
70578'5"
K6
lbsft
842015'0"
553021'4"
394527’10”
299534'5"
236041'4"
194048'6"
165555'8"
121063'7"
99071'1"
71579’0”
K5
lbsft
877015'0"
584020’11”
423027'6"
326034'1"
262514’0”
220548'2"
174056'1"
136563'7"
110071'1"
K4
lbsft
914514'8"
615020’11”
452027'2"
355033’8”
293040'7"
229048’2”
185056'1"
145563'7"
K3
lbsft
954514'5"
650020'8"
485026’11”
388033'5"
K2
lbsft
994014'1"
685520'4"
520026’11”
kgm
45104.3
31106.2
23608.2
kgm
43304.4
29506.3
22008.2
176010.2
66019.4
62019.4
50021.7
kgm
41504.5
27906.4
20508.3
kgm
39804.6
26506.4
19208.4
kgm
38204.6
25106.5
17908.5
kgm
36604.7
23806.6
16708.5
kgm
35504.8
22906.7
15908.6
116010.6
88012.7
69014.9
56017.2
48019.3
43021.5
32023.9
123010.5
95012.6
76014.8
63017.1
55019.2
42521.6
32023.9
136010.5
107012.6
88014.8
75017.0
55019.4
45021.7
32524.1
148010.4
119012.5
100014.7
79017.1
161010.3
133012.4
104014.9
84017.1
This page left intentionally blank
48
20/138 - Manual # 99904616
Section - 5 49 20/138DL Hydraulics
20/138 - Manual # 99904616
Section - 520/138DL Hydraulics
Section - 5 50 20/138DL Hydraulics
20/138 - Manual # 99904616
20/138DL - Pressure setting diagram, fixed flow pump & Danfoss RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 345 5004
Slewing systemRight A P 180 P 2611Left B P 180 P 2611
Boom cylinderDown A 125 100 1813 1450Up B 350 380 5076 5511
Jib cylinderUp A 350 380 5076 5511Down B 250 230 3626 3336
Extension cylindersExtend A P - P -Retract B P - P -
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 185 2683Left 185 2683
Boom cylinderUp 365 5294
Down - -
Jib cylinderUp 380 5511
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 330 [bar] 4786 [PSI]HDL 285 [bar] 4134 [PSI]
Max. pump performanceChoice of pump 1 x Fixed 1 x FixedPump performance 70 L/min 18.5 gpm
IMT reserves the right to introduce improvements and modifications
Section - 5 51 20/138DL Hydraulics
20/138 - Manual # 99904616
20/138DL - Pressure setting diagram, variable flow pump & Danfoss RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 345 5004
Slewing systemRight A P 180 P 2611Left B P 180 P 2611
Boom cylinderDown A 125 100 1813 1450Up B 350 380 5076 5511
Jib cylinderUp A 350 380 5076 5511Down B 250 230 3626 3336
Extension cylindersExtend A P 300 P 4351Retract B P 300 P 4351
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 185 2683Left 185 2683
Boom cylinderUp 365 5294
Down - -
Jib cylinderUp 380 5511
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 330 [bar] 4786 [PSI]HDL 285 [bar] 4134 [PSI]
Max. pump performanceChoice of pump 1 x Variable 1 x VariablePump performance 100 L/min 26.4 gpm
IMT reserves the right to introduce improvements and modifications
Section - 5 52 20/138DL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Danfoss, single-circuit fixed 6 fcts. RC (2 EXV: Grab + Rotator)
Option
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
P PVSK
HPCO
63093/63302/63304/63319
X4
X1
X2
X3
Pst
Tst PVP
T
P
LS M
A-PORTA1
B1
A-PORTA2
B2
A-PORTA3
B3
A-PORTA4
B4
A-PORTA5
B5
A-PORTA6
B6
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
4940
1
Section - 5 53 20/138DL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Danfoss, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch)
Option
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
C2 C1
V2 V1
5902
2
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
5902
7MM2M1 C1C2
V1V2
63310 / 63312
Pst
P PVSK
P1 P2
C1
C2
C3
C4
X2 X1 X3 X4
P2
C1
C2
C3
C4
P15906
2
5906
2
PVPTst
A-PORTA1
B1
A-PORT
A6
B6
A-PORT
A-PORT
A5
B5
A-PORT
A-PORTA4
B4
A-PORTA3
B3
A-PORTA2
B2
T
P
LS M
A-PORTA7
B7
58478
58478
58478
58478
58478
58478
58478
58478
58479
58478
58479
58479
V1 V2
5828
4/58
285
4940
1
D
58478
X3 X4
X1 X2
Fly-jib EXV:
Section - 5 54 20/138DL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Danfoss, single-circuit variable 6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator)
Option
Recommended
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
PVP
T
P
LS M
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
A-PORTA6
B6
A-PORTA5
B5
A-PORTA4
B4
A3
B3
A-PORT
A-PORTA2
B2
A-PORTA1
B1
63092/63301/63303/63313
P PVSKPst
Tst
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
4940
1
Section - 5 55 20/138DL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Danfoss, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch)
Option
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
PVP
C2 C1
V2 V1
5902
2
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
5902
7MM2M1 C1C2
V1V2
63309 / 63311
Pst
P PVSKP1 P2
C1
C2
C3
C4
X2 X1 X3 X4
P2
C1
C2
C3
C4
P15906
2
5906
2
Recommended
Tst
A-PORTA1
B1
A-PORT
A6
B6
A-PORT
A-PORT
A5
B5
A-PORT
A-PORTA4
B4
A-PORTA3
B3
A-PORTA2
B2
T
P
LS M
A-PORTA7
B7
58478
58478
58478
58478
58478
58478
58478
58478
58479
58478
58479
58479
4940
1
V1 V2
5828
4/58
285
D
58478
X3 X4
X1 X2
Fly-jib EXV:
Section - 5 56 20/138DL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 2 fcts.
PstTst
A-PORT
A2 B2
A-PORT
A1 B1
5522
5
PT
5849
6
5849
6
Section - 5 57 20/138DL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 4 fcts.
PstTst
D
C
5522
8
5849
6
5849
6
D
C
5522
8
A14 B14 A13 B13 A12 B12 A11 B11
5522
6 / 5
5281
PT
A-PORT A-PORT A-PORTA-PORT
Section - 5 58 20/138DL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 4 fcts. RC
D
C
5522
8
5849
6
5849
6
D
C
5522
8
PstTst
A13 B13 A12 B12
5527
6
T
B-PORT
A-PORT
A11 B11
PA-PORT
B-PORT
NEM-MODULPT
T
ø1 mmø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
49187
49187
Only when HR stabilizer
Section - 5 59 20/138DL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts.
D
C
5522
8
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
A15 B15 A14 B14 A13 B13 A12 B12
5527
7
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
PA-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Section - 5 60 20/138DL Hydraulics
20/138 - Manual # 99904616
Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts. RC
D
C
5522
8
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
P
P
A15 B15 A14 B14 A13 B13 A12 B12
5527
5
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
A-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
NEM-MODULT
T
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Only when HR stabilizer
49187
49187
This page left intentionally blank
61
20/138 - Manual # 99904616
This page left intentionally blank
62
20/138 - Manual # 99904616
Section - 6 63 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Section - 620/138SL - 20/138DL Dimension Drawings
Section - 6 64 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Lifting capacity with winch
Hydraulic hoist type MAXW MAXWD1500 kg 3000 kg3305 lb
2500 kg 5000 kg5510 lb
Dinamic S 25Brevini 2500
Dinamic P9E
Dinamic P15E
3200 kg 6400 kg7050 lb
11020 lb
6610 lb
14100 lb
90°
0°
65°
Not recommended working angle.
Section - 6 65 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138SL- Dimension sketch K2 - K6(2
250)
88.5
8”
49.21”
98.43”(1250)
(2500)
11.42”(290)
CL CHASSIS
TOP CHASSIS
15”
2.44
”(6
2)
37.20”
32.28”(381)
(945)
(820)
TOP CHASSIS
2.87”(73)
1.12
”(2
8.5)
85.1
2”106.
9”
76.8
9”
2.99 (TYP.)(76) (TYP.)
99.2
9”
(216
2)(271
5)
(195
3)(252
2)
186.1”(4726)
A
A
A-ATOP CHASSIS
Section - 6 66 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138DL- Dimension sketch K2 - K6
1.12
”(2
8.5)
2.87”(73)
78.0
3”
86.7
3”
C
15.87”(403)
39.57”(1005)
E
2.36
”
(198
2)
(220
3)
(60)
11.42”(290)
CL CHASSIS
B
D
98.43”
49.21”
(2500)
(1250)
A
A
TOP CHASSIS
A-A
TOP CHASSIS
TOP CHASSIS
[mm] B C D EK2 4427 2690 2295 885K3 4503 2760 2295 885K4 4579 2800 2295 885K5 4655 2800 2295 885K6 4731 2800 2295 885K7 4807 2800 2295 995K8 4883 2800 2335 995
[in] B C D EK2 174.29 105.91 90.35 34.84K3 177.28 108.66 90.35 34.84K4 180.28 110.24 90.35 34.84K5 183.27 110.24 90.35 34.84K6 186.26 110.24 90.35 34.84K7 189.25 110.24 90.35 39.17K8 192.24 110.24 91.93 39.17
Section - 6 67 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch K7 - K8
1.12
”28
.5
2.87”(73)
K7: 189.25”K8: 192.24”(K7: 4807)(K8: 4883)
78.0
3”
86.7
3”110.
24”
(198
2)
(220
3)(280
0)
98.43”
49.21”
11.42” CL CHASSIS
2.36
”(6
0)
15.87”
39.17”(2500)
(1250)
(290)
(403)
(995)
(K7:
229
5)(K
8: 2
335)
K7:
90.
35”
K8:
91.
93”
A
A
A-A
TOP CHASSIS TOP CHASSIS
TOP CHASSIS
Section - 6 68 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138SL - Slewing Radius
R 18.70”
R 15.75”
R 25”
(R 475)
(R 400)
(R 635)
95.6
7”
84.2
5”
82.0
9”
83.4
6”
R 15.94”(R 405)
11°
74.6
1”
(243
0)
(214
0)
(208
5)
(212
0)
(189
5)
TOP CHASSIS
Section - 6 69 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138DL - Slewing Radius
12°
TOP CHASSIS
R 20.28”
R 16.34”
R 25”
(R 515)
(R 415)
(R 635)
95.6
7”
84.2
5”
79.5
3”
81.1
0”
R 15.94”(R 405)
66.7
3”
(243
0)
(214
0)
(202
0)
(206
0)
(169
5)
Section - 6 70 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch for truck-mounted loader
Max. 1.26”(Max. 32)
Max. 1.26”(Max. 32)
Max. 6.29”
1.02”(26)
3.15
”(8
0)
7.28”
(Max. 160)
(185)
1.57
”(4
0)
29.5
3”(7
50)
14.8
8”(3
78)
Min. 22.91”
Max. 41.73”(Min. 582)
(Max. 1060)
14.8
8”(7
50)
(378
)
Min. 35.43” / Max. 40.94”(Min.900 / Max.1040)
1.65”(42)
5.51”(140)
1)
Mounting kit 3 x M33x2 bolts + 1 x M30x2 bolts
Mounting kit 8 x M24x2 bolts
Notes:
1) Values dictated by strength considerations.
2) Drill hole when assembling
3) As regards installation - please see IMT Installation Manual
4) Mounting kits or spare parts - please see the Spare Parts Catalogue of the individual loader
See note 2)
1)1)
M30x2
CL CHASSIS
1.65”(42)
Section - 6 71 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138SL - Lifting Height at Column
H1
86.6
1”( 2
.2m
)
R=39.37” (R=1m)
TOP CHASSIS
H1 H1K2 2.74 m 107.9 inK3 2.65 m 104.3 inK4 2.56 m 100.8 inK5 2.47 m 97.24 inK6 2.38 m 93.70 inK7 2.29 m 90.16 inK8 2.21 m 87.01 in
Section - 6 72 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138DL - Lifting Height at Column
H1 H1K2 2.74 m 107.9 inK3 2.65 m 104.3 inK4 2.56 m 100.8 inK5 2.47 m 97.24 inK6 2.38 m 93.70 inK7 2.29 m 90.16 inK8 2.21 m 87.01 in
H1
86.7
5” 2
203.
5mm
TOP CHASSIS
R=39.37” (R=1m)
Section - 6 73 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch, fixed stabilizer legs
A 777mm 877mm 977mm
A 30.59” 34.53” 38.46”
11.42”(290)
CL CHASSIS
A20
.28”
(515
)
A
63.98” 91.54”
81.30”(2065)
81.30”(2065)
CL CHASSIS
254.1”(6455)
A
219.5”
(1625) (2325)
(5575)
A
219.5” / 254.1”(5575 / 6455)
26.5
7”17
.13”
(675
)(4
35)
TOP CHASSIS
Cylinder Stands, short
TOP CHASSIS
TOP CHASSIS
11.42”(290)
20.2
8”(5
15)
20.2
8”(5
15)
20.2
8”(5
15)
63.98”(1625)
91.54”(2325)
Section - 6 74 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch, fixed stabilizer legs
8.19
”
12.1
3”
12.8
7”14
.88” (208
)
(308
)
(372
)(3
78)
Section - 6 75 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch, swing-up stabilizer legs 20°- 60° (manual)
AA20
.39”
(518
)
219”
63.94”
81.34”
253.8”
(5562)
(1624)
(2066)
(6446)
A A
CL CHASSIS
CL CHASSIS
TOP CHASSIS
TOP CHASSIS
11.42”(290)
11.42”(290)
20.3
9”(5
18)
20.3
9”(5
18)
20.3
9”(5
18)
63.94”(1624)
91.10”(2314)
81.34”(2066)
Type R-20° (Obsolete)
Type R-60°
A
38.19”
37.87”
34.25”
33.94”
30.31”
30.00”
A
Type R-20° (Obsolete)
Type R-60°
A
970mm
962mm
870mm
862mm
770mm
762mm
A
Section - 6 76 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch, swing-up stabilizer legs 20°- 60° (manual)
C
B60°30° B
C
100
3.94”(100)
21°D
8.19”
12.13”
14.88” 14.65”
(208)
(308)
(378) (372)
Type R-20° (Obsolete)
Type R-60°
C
B
923mm
574mm
836mm
524mm
750mm
474mm
438mm402mm366mm
D
C
B
36.34”
22.60”
32.91”
20.63”
29.53”
18.66”
17.24”15.83”14.41”
D
Section - 6 77 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic)
A
B
CL CHASSIS
A16
.22”
(412
)
63.98” 91.34” 63.98”
219.3”
CL CHASSIS
91.34”81.30” 81.30”
135.8”
(1625) (2320) (1625)
(5570)
(2320)(2065) (2065)
(6450)
2.48
”(6
3)
AA
A
TOP CHASSIS
TOP CHASSIS
TOP CHASSIS
1.73
”2.
52”
(44)
(64)
11.42”(290)
16.2
2”(4
12)
16.2
2”(4
12)
16.2
2”(4
12)
11.42”(290)
A 34.61” 38.54” 42.48”
30.59” 34.53” 38.46”B
A 879mm 979mm 1079mm
777mm 877mm 977mmB
Section - 6 78 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic)
8.19
”
12.1
3”
14.6
5”14
.88” (208
)
(308
)
(372
)(3
78)
Section - 6 79 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138SL - Dimension sketch, TS Top Seat (RC)
62.0
1”19
.29”
30.91”
34.25”
19.09”
(785)
(870)
(485)
93.5
0”
(157
5)(4
90)
(237
5)
R42
.91”
(R10
90)
R40
.55”
(R10
30)
Section - 6 80 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138DL - Dimension sketch, TS Top Seat (RC)
R42
.91”
(R10
90)
R40
.55”
(R10
30)
(125
0)49
.21”
62.0
1”19
.29”
30.91”
34.25”19.09”
(785)
(870)(485)
93.5
0”
(157
5)(4
90)
(237
5)
Section - 6 81 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138SL - Dimension sketch, TS Top Seat (HC linear)
2.44
”(6
2)
49.2
1”(1
250)
61.8
1”19
.29”
30.91”
34.25”
19.09”
(785)
(870)
(485)
93.3
1”
(157
0)(4
90)
(237
0)
R42
.91”
(R10
90)
R40
.55”
(R10
30)
Section - 6 82 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138DL - Dimension sketch, TS Top Seat (HC linear)
62.0
1”19
.29”
30.91”
34.25”19.09”
(785)
(870)(485)
93.3
1”
(157
5)(4
90)
(237
0)
R42
.91”
(R10
90)
R40
.55”
(R10
30)
2.44
”(6
2)
Section - 6 83 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138SL - Dimension sketch, TS Top Seat (Danfoss X)
62.0
1”19
.69”
32.87”
36.22”24.61”
(835)
(920)(625)
93.7
0”
(157
5)60
.24”
(153
0)(5
00)
(238
0)
R48
.03”
(R12
20)
R46
.06”
(R11
70)
0.78
”(2
0)
Section - 6 84 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138DL - Dimension sketch, TS Top Seat (Danfoss X)
62.0
1”19
.69”
32.87”
36.22”
24.61”
(835)
(920)
(625)
93.7
0”
(157
5)60
.24”
(153
0)(5
00)
(238
0)
R48
.03”
(R12
20)
R46
.06”
(R11
70)
0.78
”(2
0)
Section - 6 85 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138SL - Dimension sketch, TS Top Seat (HC X)
24.61”(625)
93.7
0”
54.7
2”(1
390)
(238
0)
R48
.03”
(R12
20)
R46
.06”
(R11
70)
0.78
”(2
0)
Section - 6 86 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138DL - Dimension sketch, TS Top Seat (HC X)
62.0
1”19
.69”
32.87”
36.22”24.61”
(835)
(920)(625)
93.7
0”
(157
5)54
.72”
(139
0)(5
00)
(238
0)
R48
.03”
(R12
20)
R46
.06”
(R11
70)
0.78
”(2
0)
Section - 6 87 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138SL - Dimension sketch, ladder for TS
20.4
7”48
.43”
(520
)(1
230)
TOP CHASSIS
Notes: 1) Ladder cannot be used for TS RC
2) There is no access to the top seat when the loader is in stowing position
Section - 6 88 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138DL - Dimension sketch, ladder for TS
TOP CHASSIS
20.4
7”48
.43”
(520
)(1
230)
Notes: 1) Ladder cannot be used for TS RC
2) There is no access to the top seat when the loader is in stowing position
Section - 6 89 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Technical data, winch
Performance (at 150 bar) 2176 psi: 1.5T winch 1.5T winch 2.5T winch 2.5T winch
Max. wire pull – 1st layer 1500 kg 3307 lb 2500 kg 5512 lbMax. wire pull – 2nd layer 1370 kg 3020 lb 2300 kg 5071 lbMax. wire pull – 3rd layer 1260 kg 2778 lb 2100 kg 4630 lbMax. wire pull – 4th layer 1170 kg 2579 lb 1950 kg 4299 lb
Wire speed (at 40 l/min.) 10.57 gpm: 1.5T winch 1.5T winch 2.5T winch 2.5T winch
Max. wire speed – 1st layer 22 m/min 72'2"/min 24 m/min 78'9"/minMax. wire speed – 2nd layer 24 m/min 78'9"/min 26 m/min 85'4"/minMax. wire speed – 3rd layer 26 m/min 85'4"/min 28 m/min 91'/minMax. wire speed – 4th layer 28 m/min 91'10"/min 30 m/min 98'5"/min
Weights: 1.5T winch 1.5T winch 2.5T winch 2.5T winch
Tare weight, winch (CE) 65 kg 143 lb 90 kg 198 lbFixed parts (valve section, brackets, hoses etc) 50 kg 110 lb 50 kg 110 lbWire Ø10 x 50 m 30 kg 66 lb 30 kg 66 lbSpare parts, single snatch block 30 kg 66 lb 30 kg 66 lbSpare parts, double snatch block 40 kg 88 lb 40 kg 88 lb
Section - 6 90 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch, winch
2.5T: 37.80”1.5T: 38.58”
(2.5T: 960)(1.5T: 980)
0.39”(10)
0.39”(10)
Section - 6 91 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch, stand-up platform (std.)
BøD
øD A B A BK1, K2, K3 ø480 200mm 68mm 7.87” 2.68”
K4 ø520 220mm 48mm 8.66” 1.89”K5 ø570 245mm 23mm 9.65” 0.91”K6 ø620 270mm 2mm 10.63” 0.08”
Section - 6 92 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Dimension sketch, extra valves K7, K8
øD
A
2 EXV: 40.55”1 EXV: 39.17”(2 EXV: 1030)(1 EXV: 995)
101.
34”
(257
4)
øD A B A BK7 ø720 285mm 0mm 11.22” 0.00”
K8 ø720 285mm 0mm 11.22” 0.00”
Section - 6 93 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
Stowed in truck body
93.6
6”
15°
98.3
9”
85.6
3”
53.3
9”
(237
9)
(249
9)
(217
5)
(135
6)
TOP CHASSIS
TOP CHASSIS
Section - 6 94 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138SL - Centers of Gravity
H2
V2 H1
f
V1
Z3
V3
H4 H3
G2
G3
G2
V2
G1
CL CHASSIS
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G320/138SL - K2 190 2075 770 135 2380 340 1705 25 290 850 1250 210020/138SL - K3 190 2100 820 135 2925 315 1780 45 290 850 1475 232520/138SL - K4 190 2150 815 135 3840 310 2015 60 290 850 1550 240020/138SL - K5 190 2175 835 135 4585 300 2130 80 290 850 1690 254020/138SL - K6 190 2195 855 135 5315 285 2225 90 290 850 1820 267020/138SL - K7 190 2215 875 135 6090 270 2315 105 290 850 1950 280020/138SL - K8 190 2225 890 135 6595 265 2365 115 290 850 2025 2875
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G320/138SL - K2 7.48 81.69 30.31 5.31 93.70 13.39 67.13 0.98 11.42 1874 2756 463020/138SL - K3 7.48 82.68 32.28 5.31 115.16 12.40 70.08 1.77 11.42 1874 3252 512620/138SL - K4 7.48 84.65 32.09 5.31 151.18 12.20 79.33 2.36 11.42 1874 3417 529120/138SL - K5 7.48 85.63 32.87 5.31 180.51 11.81 83.86 3.15 11.42 1874 3726 560020/138SL - K6 7.48 86.42 33.66 5.31 209.25 11.22 87.60 3.54 11.42 1874 4012 588620/138SL - K7 7.48 87.20 34.45 5.31 239.76 10.63 91.14 4.13 11.42 1874 4299 617320/138SL - K8 7.48 87.60 35.04 5.31 259.65 10.43 93.11 4.53 11.42 1874 4464 6338
[mm] [kg]
[in] [lbs]
Section - 6 95 20/138SL - 20/138DL Dimension Drawings
20/138 - Manual # 99904616
20/138DL - Centers of Gravity
f
H2
V2
H1
H3H4
V1
Z3
V3
G3
G2
CL CHASSIS
G1
G2 V2
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G320/138DL - K2 190 2055 795 135 2250 325 1610 25 290 850 1325 217520/138DL - K3 190 2100 820 135 2925 315 1780 45 290 850 1475 232520/138DL - K4 190 2130 840 135 3665 305 1925 60 290 850 1625 247520/138DL - K5 190 2160 855 135 4390 290 2045 80 290 850 1765 261520/138DL - K6 190 2180 870 135 5105 275 2140 90 290 850 1895 274520/138DL - K7 190 2195 890 135 5865 265 2230 105 290 850 2025 287520/138DL - K8 190 2205 910 135 6360 255 2285 115 290 850 2100 2950
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G320/138DL - K2 7.48 80.91 31.30 5.31 88.58 12.80 63.39 0.98 11.42 1874 2921 479520/138DL - K3 7.48 82.68 32.28 5.31 115.16 12.40 70.08 1.77 11.42 1874 3252 512620/138DL - K4 7.48 83.86 33.07 5.31 144.29 12.01 75.79 2.36 11.42 1874 3583 545620/138DL - K5 7.48 85.04 33.66 5.31 172.83 11.42 80.51 3.15 11.42 1874 3891 576520/138DL - K6 7.48 85.83 34.25 5.31 200.98 10.83 84.25 3.54 11.42 1874 4178 605220/138DL - K7 7.48 86.42 35.04 5.31 230.91 10.43 87.80 4.13 11.42 1874 4464 633820/138DL - K8 7.48 86.81 35.83 5.31 250.39 10.04 89.96 4.53 11.42 1874 4630 6504
[mm] [kg]
[in] [lbs]
IMT reserves the right to make changes in engineering, design, specifications, add improvements or discontinue manufacturing at any time without notice or obligation.
IMT and IMT LOGO are registered trademarks of Iowa Mold Tooling Co., Inc., Garner, IA, USA.© 2017 Iowa Mold Tooling Co., Inc. All Right Reserved.
IOWA MOLD TOOLING CO., INC.
P.O. Box 189 Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com
top related