2010 edition - brenlo · 2019-06-04 · also have an inventory of over 10,000 custom knives. knives...
Post on 30-Mar-2020
2 Views
Preview:
TRANSCRIPT
Architectural Profiles2010 EDITION
Residential Builder Sales Phone: 416 749-6857 Fax: 416 749-8969 Toll Free: 1-877-816-6607
Commercial Sales Division Phone: 905 677-9204 Fax: 905 677-7859 Toll Free: 1-866-256-8210
Showroom & Customer Pick Up 41 Racine Road, Toronto, Ontario Canada M9W 2Z4
www.brenlo.ca
TM
1
The Brenlo Story
In the late 1980s, a major change was taking place in the
construction of fine homes. Architects and designers were
looking for unique products that would make their project
stand out from the masses. Windows and doors were now
becoming the focal point of these designer showcase
houses. Curves and arches were appearing more common
place and elaborate library walls were being created.
Quality was being taken to a new and higher level and
mediocrity was no longer acceptable. Subsequently, there
became an increased demand for quality and design in
custom fine hardwood moulding profiles and trims,
products that would not only complete the architectural
design of each of these uniquely customized homes but
enhance it. Brenlo Custom Wood Mouldings would be the
company that would meet this need.
With roots tied closely to the specific and demanding
requirements of the architects, designers and builders of
fine homes, Brenlo set out to deliver uncompromising
quality and service to this market. And as a result, today,
Brenlo is recognized by this discerning group as their pre-
emanate millwork manufacturer supplier.
In April of 2005, Brenlo merged with its sister company
Britannia Inc. to create a commercial/industrial and
Lumber Yard division. With the increase of six moulders
in our new facility, this amalgamation has made Brenlo
the largest custom moulding manufacturer in Ontario.
The current 73,000 sq. ft. facility in Toronto has become
our distribution centre. The 80,000 sq. ft. Mississauga
state-of-the-art facility has become our manufacturing
location. Brenlo provides a broad range of architectural
wood mouldings and related products, curved mouldings
and arches, as well as doors and exterior millwork
components. Over 300 in-stock profiles are available for
next day delivery.
It has been Brenlo’s continued commitment to quality that
has ensured every foot of our product is useable, thereby
giving our customer the very best in yield with minimal
waste. Each one of Brenlo’s moulding operators operates
one specific moulding machine. Their intimate
knowledge of exacting machine and knife tolerances
allows them to produce consistent, high quality profiles
each and every time.
The Brenlo tool room specializes in developing cost
effective solutions to produce even the most complex
custom designs. With over 10,000 in-stock profile knives,
Brenlo can save the expense of cutting new knives for
custom run needs. And as a repeat customer, your past
projects are indexed and inventoried for future use.
With an experienced team of professionals from sales to
production, Brenlo remains the leader in the moulding
industry. Simply look at the sharpness of the edges of any
Brenlo produced profile, or the smoothness of the surface
of our finish, or the quality of the wood and you will know
that you’re getting the very best in wood mouldings from
Brenlo.
Brenlo’s quality speaks for itself on projects such as: #1
Post Road, Toronto, #9 Jackes Avenue, Toronto, Casino
Rama, Orillia, Cheddington Place, Toronto, Deer Creek
Golf & Country Club, Ajax, Niagara Falls Casino &
Resort, Niagara, Prince Arthur Condominium & Hotel,
Toronto, Royal Casino, St. Kitts and Windsor Arms Hotel
& Condominium, Toronto.
Our designs have been much imitated, but our quality
and service has never been equaled.
Introduction
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
2
General Termsand Conditions
CREDITTo establish credit, a credit application must be completedin full and sent to our credit department. All first timeorders will be on a C.O.D. basis, unless credit terms havebeen established. Custom orders are C.O.D. unless pre-approved by the Credit Dept.
RETURNS AND CLAIMSReturns must be authorized in advance, and may besubject to a 20% restocking charge made through thewarehouse. 30% restocking charge for returns picked upat job-site. $65.00 pick up fee for our trucks.
All returns (except warranty work) must be shipped to ourplant freight prepaid.
Please notify our office within 24 hours of receiving anydefective product, or short shipment of product.
Copyright and TrademarkBrenlo, Brenlo Custom Wood Moulding, and productprofile design and code, are the trademarks of BrenloLtd. registered in Canada. You shall not display,disparage, dilute or taint our trademarks and servicemarks or use any confusingly similar marks, or use ourmarks or designs in such a way that would misrepresentthe designer or identity of the owner. Any permitted useof our trademark designs and service marks inures to thebenefit of Brenlo Ltd.
All other trademarks, service marks or registeredtrademarks appearing on these or any Brenlo Ltdpublications or website are the trademarks or servicemarks of their respective owners.
LENGTHSWe buy our wood in random lengths and produce theoptimum length of moulding according to each particularuse. Unless specified, mouldings are produced in randomlengths varying from three (3) to sixteen (16) feet.(Produced to the nearest foot)
For random length and custom millwork orders, pleaseallow for a 10-15% waste factor when ordering.
Orders that require specified lengths will be subject to a15% surcharge.
MINIMUMS• There will be a processing charge of $5.00 for all pick-
up orders under $30.00.• A delivery charge is applicable to orders under
$250.00.
SAMPLESSamples are available upon request.
***SPECIAL NOTE: All mouldings may have natural colour variation due to characteristics of wood types.Please inquire if you have a special requirement.
We reserve the right to change prices and product specifications without notice
www.brenlo.ca
TM
3
PLEASE NOTE: The moulding profiles shown may not be exactly as illustrated. Samples are available.
General MouldingProduct Catalogue
Casings and BasesBrenlo Ltd. utilizes many combinations of various centerand edge profiles to produce a multitude of standardstocked bases and casings. All profiles on these pagesare drawn to actual size. There may be slight variationsbetween the drawings and actual profiles. Werecommend you obtain a sample for situations requiringvery accurate material dimensions. Delivery is usually 1to 2 days on most stock items.
Custom MouldingsIf you cannot find the mouldings that suit your needs inour stocked moulding selection, we will be glad toproduce any custom moulding you desire. Center andedge profiles on our standard bases and casings can bemixed and matched in various combinations to create thecustom profile that suits your requirements. Stock isavailable up to 9-1/4 inches wide, in 4/4, 5/4, 6/4and 8/4 thicknesses. These profiles are all available inour knife collection, therefore knife grinding is notnecessary. Contact our order desk for pricing.
Set-up Charges on CustomMouldingsSet-up charges may be applied to custom mouldingorders. Contact our order desk for pricing.
Custom Knife GrindingWe specialize in milling mouldings to match existingmillwork. Knives can be ground to match any pattern orprofile that cannot be found in this catalogue. We canproduce knives from a sample of an existing moulding,architectural drawing, tracing or paper pattern. Customorders can generally be delivered within 2 weeks. Wealso have an inventory of over 10,000 custom knives.Knives remain the property of Brenlo Ltd.
Raw MouldingSince we do the actual manufacturing, our rawmouldings come in a wide variety of shapes and designsas well as types of wood. Additional wood types notlisted can be obtained by special request.*Special Note: All raw moulding may have natural
colour variations due to characteristics of the wood type.
Embossed MouldingsBrenlo is pleased to introduce our new line of embossedmouldings. At our state of the art facility, Brenlo’sembossing process is skillfully applied to any species andstock profile available in our catalogue. Our selection ofstock embossing wheels is listed below, howevernumerous other wheel designs and sizes are available.Please inquire for more information.
Brenlo Stock Embossed ProfilesCase 3/4" x 3-1/2" - #810E PoplarBase 3/4" x 7-1/4" - #820E Poplar
Brenlo Embossing Patterns Available:
Rope (shown)
Bead & Reel
Egg & Dart
Running Coin
Please inquire at the order desk for a current list ofembossing designs available.
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
4
Interior Wood Mouldings:Choose from our extensive selection of stock architectural mouldings, available in:
Items ready to be shipped include base mouldings, casings and embossed mouldings.
Special Order Mouldings: Virtually any profile can be run in any species. In addition to those listed above, Brenlo has available on request:African Mahogany, Ash, Beech, Birch, Fir, Hickory, Quartered / Rift Red and White Oak to name a few. Pleaseinquire about pricing and lead times.
Exterior Architectural Components:Our exclusive Duraboard PW product line is available for any type of exterior finishing or can be custom machined toyour specifications. We also distribute a wide variety of exterior columns, brackets and EZ Bend PVC products.
Interior Doors:We stock a full line of quality residential and commercial interior doors in 80", 84", 90" and 96" heights. Customdoors are available by special order. Manufacturers include: Masonite, Cascades and Harring Doors.
Hardware:We stock a line of residential hardware including: Door handles, hinges, bullet catches, closet rods, pocket door tracksand air nails, etc.
Sheet Products:Order from our stock of high quality sheet products:
Custom Grinding and Manufacturing:In-house custom grinding is available to match any wood profile. Profiles can be created from existing samples, orfrom new designs. Plus, we have over 10,000 custom knife profiles in stock, ready for machining custom runs ofmouldings.
Other Products
• MDF• MDF Bead Board / T & G• MDO (Crezon) • Birch Plywoods
• Oak Plywoods• Maple Plywoods• Cherry Plywoods• Walnut Plywoods
• Flex Ply• Duraboard PW• Arreis• Extira
• Khaya Mahogany• EZ Bend PVC Exterior
• American Yellow Poplar• Eastern White Pine• Appalachian Red Oak
• Hard White Maple• American Black Cherry• Knotty Pine
• Genuine Mahogany• Walnut
www.brenlo.ca
TM
55
LEADERS IN DESIGN FOR ARCHITECTURAL MOULDINGS
Species ChartSection 1: CasingsSection 2: Casing / Back BandSection 3: Back BandsSection 4: Plinth BlocksSection 5: Plinth Blocks and Corner BlocksSection 6: BaseboardsSection 7: Crown MouldsSection 8: Bolections / ApronsSection 9: Cove MouldsSection 10: Cap MouldsSection 11: Door StopsSection 12: Panel Moulds Section 13: Bed Moulds / Quarter RoundsSection 14: T-Astragals / Battens / Fascias / Window MullionsSection 15: Brick Mould / Shingle MouldSection 16: Pilasters / Column ComponentsSection 17: Chair RailsSection 18: Glass Beads / Shelf Edges / Corner Guards / Corner BeadsSection 19: Half Rounds / Base Shoe / Flat AstragalsSection 20: Window StoolSection 21: Bar RailSection 22: Tongue & Groove PanelingSection 23: MiscellaneousSection 24: Designer SeriesSection 25: Signature SeriesSection 26: MDF ProfilesSection 27: CombinationsSection 28: Custom Shop, Arches and CurvesSection 29: Notes
Index 2010 Edition
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
66
CASING Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend MBA MBB1 3/4 ” x 2-3/4” • • • • • • • • 42/42B 351A 3/4” x 3-1/2” • • • 42B/42C 354 7/8” x 3” • 349 467 3/4” x 3-1/2” • • • 349/349B 357A 3/4” x 2-3/4” • • • 349/349A 3515 3/4” x 2-3/4” • 312 3615B 3/4” x 3-1/4” • 312 3619 3/4” x 4-1/4” • • • 353B/354 n/a19A 3/4” x 2-3/4” • • 353B n/a20 3/4” x 2-3/4” • • • • • 354 30/3920B 3/4” x 3-1/2” • 349B/900 30/3922 3/4” x 3-1/2” • 53 3423 3/4” x 3-1/16” • 358 3425a 3/4” x 3-1/2” • • • 25B 3425S 3/4” x 2-1/2” • 25B 34101 3/4” x 3-1/2” • 306/307 38102 3/4” x 3-1/2” • 53/302C 34/39103 3/4” x 3-1/2” • 1x8/306 n/a106 3/4” x 3-1/2” • • • • 306/307C 37106A 3/4” x 2-3/4” • 307 37500 1-1/8” x 3” • 42B n/a600 1-1/8” x 3” • 25B n/a700 7/8” x 3-1/2” • • • • • • • 900C 701700B 7/8” x 3” • 900 701800 7/8” x 3-1/2” • • • • • 352A/356A 35X810 3/4” x 3-1/2” • 820 35810E 3/4” x 3-1/2” • 820E 35888 3/4” x 2-3/4” • • • • 42B/349 n/a2000 11/16” x 3-1/8” • 2051D 20012005 5/8” x 2-5/8” • 2051C 20062010 1” x 4-1/2” • 2053D 20112015 3/4” x 3-1/2” • 2053D 20162100 1-5/16” x 4-1/2” • 2140 N/A2108 1-5/16” x 1-1/2” • 2148 N/A
BACK BAND Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend30 1-5/8” x 1-5/8” • • •32A 1-1/4” x 2-1/32” • 34 3/4” x 1-3/8” • • • • 34ext 3/4” x 1-1/2” • 35 7/8” x 1-5/8” • • • • • • •35ext 7/8” x 1-3/4” • • • • • • • •36 1-3/32” x 1-5/8” • 37 3/4” x 1-5/16” • • • • 38 13/16” x 1-3/8” • 39 7/8” x 1-1/2” • 46 1-5/16” x 1-9/16” • 701 1-1/8” x 1-1/2” • 2001 1-13/16” x 2-3/4” • 2006 1-5/16” x 2-1/4” • 2011 1-5/16” x 2-1/8” • 2016 1-3/4” x 1-1/2” •
Species Chart
TM
77
Species Chart
PLINTH BLOCK Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend337-4.5 1-3/8” x 20” x 4-1/2” • • • 337-3.75 1-3/8” x 20” x 3-3/4” • • 337-3 1-5/16” x 16” x 3” • • • • 338 1-3/4” x 4-3/8” • 339 7/8” x 4-1/2” • 735 1-15/16” x 4-7/16” • • •2002 2-1/4” x 5-1/2” •2007 1-11/16” x 4-5/8” •2012 2pc •2017 2pc •2030 1-3/4” x 4-3/8” •2030B 1-3/4” x 5-1/8” •2130 1-1/2” x 4-7/8” • M
BASEBOARD Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend MCA MBB25B 3/4” x 5-1/2” • 25S/25A 3425C 3/4” x 7-1/4” • 25S/25A 34/3742 3/4” x 4-1/2” • • • • • 1/1A 3542B 3/4” x 5-1/2” • • • • • • • 1/1A 3542A 3/4” x 6-1/2” • 1/1A 3542C 3/4” x 7-1/4” • 1/1A 35/3653 3/4” x 5-1/2” • 22 34302C 3/4’ x 7-1/4” • 102 34/39306 3/4” x 7-1/4” • • 101/106 37/38307 3/4” x 5-1/2” • • 106/106A 37307C 3/4” x 7-1/4” • • • 106 37308 3/4” x 8-1/2” • 102 34/39309 3/4” x 8-1/2” • 2000/05 2001/06310 13/16” x 8-1/2” • 106 37312 11/16” x 4-1/4” • 15 36349A 3/4” x 4-7/8” • 7/7A 34349 3/4” x 5-1/2” • • 7/7A 34349B 3/4” x 7-1/4” • • • • • • 7/7A 34352 3/4” x 6-1/2” • • 1A/800 35/36352B 3/4” x 7-1/4” • • • 1A/800 35/36353B 3/4” x 7-1/4” • 19/19A NA354 3/4” x 7-1/4” • 20/20B 30/39356A 3/4” x 6-1/2” • 800 35X358 3/4” x 5-1/2” • 23/23A 34820 3/4” x 7-1/4” • 810 35820e 3/4” x 7-1/4” • 810E 35900 7/8” x 5-1/2” • 700/700B 701900A 7/8” x 6-1/2” • 700/700B 35X/701900C 7/8” x 7-1/4” • • 700/700B 35X/701900D 7/8” x 8-1/2” • • 700/700B 35X/701910 13/16” x 9-1/4” • 700/700B 35X/7012051C 7/8” x 7-1/4” • 2005 20062051D 7/8” x 8-1/2” • • 2000/05 2001/062053D 1” x 8-1/2” • 2010/15 2011/162140 3/4” x 8-1/2” • 2100 N/A2148 13/16” x 9-1/4” • 2108/20 N/A/30
www.brenlo.ca
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
8
Species Chart
CORNER BLOCK W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend65 7/8” x 3” x 3” • • • • 66 1” x 4-1/2” x 4-1/2” • • • 66A 1” x 3-3/4” x 3-3/4” • • 67 1-3/8” x 4-1/2” x 4-1/2” • • • 67A 1-3/8” x 3-3/4” x 3-3/4” • • • 68 1-5/16” x 3” x 3” • • • • •
CROWN Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend70 3/4” x 5-1/4” • • • • • • •70B 3/4” x 7” • • •70C 7/8” x 8-1/2” • •71 3/4” x 4-1/4” • • • • • • •72 3/4” x 3-1/2” • • • • • • •72B 3/4” x 4-1/4” • • • • • • •72C 3/4” x 5-1/4” • • • • •73 3/4” x 6-1/4” •507 7/8” x 5-1/2” • • 509 13/16 ” x 3-11/16” • • 520 3/4” x 4” • •523 3/4” x 2-3/8” • •535 3/4” x 3-1/2” • •549 13/16” x 3-1/4” •552 13/16” x 5-3/16” •573 1-1/4” x 5-1/2” •578 1” x 4-3/4” •2150 1” x 4-3/4” •
BOLECTION Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend82 1 3/4” x 4” •83 1-5/8” x 5-1/2” • •663 1-5/8” x 5-1/2” •
APRON Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend81 1-5/16” x 3-1/4” •88 1-1/4” x 3-1/4” • • • • • • •89 1-5/16” x 3-1/4” •
ARCHITRAVE Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ BendL1 1-3/4” x 4-3/4” • •
COVE Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend90 1/2” x 1/2” • • • •91 3/4” x 3/4” • • • • • •92 1” x 1” • • •93 1-1/4” x 1-1/4” • • • •94 3/4” x 3-1/2” • • • • •95 5/8” x 5/8” •
www.brenlo.ca
TM
9
CAP MOULDS Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend96 3/4” x 1-3/8” •97 9/16” x 1-1/8” •98 13/16” x 1-3/4” •
DOOR STOPS Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend108 7/16” x 1-5/8” • • • •110 3/8” x 1-3/8” • • • • • • • •111 7/16” x 1-3/4” • • •113 7/16” x 1-3/4” • • • • • • • •116 7/16” x 1-3/4” • • • •117 1/2” x 2-1/2” • • •
PANEL MOULDS & BASE CAPS W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend118 7/16” x 3/4” • • • • • • • •119 1/2” x 1-1/16” • • • • • • • •121 11/16” x 1-3/8” • • •122 5/8” x 1-9/16” • • • • • • • •122A 7/16” x 1-1/8” • • • • • • • •122B 3/4” x 2-3/16” •123 9/16” x 1-3/4” • •124 3/4” x 2-1/4” •125 1-1/16” x 1-1/2” • • • • •126 1/2” x 1-5/8” •129 3/8” x 1” • • • •130 1“x 1-1/4” • • • • • 3/4” rabbet130S 7/8“x 1-1/16” • • • • • 1/2” rabbet131 5/8” x 1” • • • • • • • 1/4” rabbet132 1-1/4”x 1-5/8” • • • • • • • 3/4” rabbet133 7/8”x 1-3/8” • • • • • • • • 1/2” rabbet134 3/8” x 11/16” • • • • •327 1/2” x 1-3/4” •328 7/16” x 1-5/16” • • • • •329 3/8” x 1-1/8” • • •608 7/16” x 11/16” •620 1/2” x 1-1/4” •632 3/4” x 1-5/8” • • • • • 1/2” rabbet645 11/16” x 2-1/2” •648 3/4” x 2-1/4” •649 3/4” x 1-3/4” •651 7/8” x 3” •652 7/8” x 3” •666 1/2” x 7/8” • •
BED MOULD Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend135 5/8” x 2-3/4” • • •136 5/8” x 2-1/4” • • • •138 5/8” x 1-5/8” • • • •
Species Chart
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
10
QUARTER ROUND W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend141 1” x 1 •142 3/4” x 3/4” • • • •143 5/8” x 5/8” • • •144 1/2” x 1/2” • • •
TONGUE & GROOVE W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend145 3/8” x 3-1/8” • • • • • •145B 1/2” x 5-1/2” •145S 3/8” x 3-1/8” •146 3/4” x 3-1/2” •146A 3/4” x 4-3/4” •146B 3/4” x 5-1/2” •
THRESHOLDS Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend D147 13/16” x 5-1/2” x 36” •
NOSING Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend149 1” x 3-1/2” •
BATTEN Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend150 9/16” x 2-1/4” •151 3/4” x 1-5/8” •
SHINGLE MOULD Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend152 1-7/32” x 1-11/16” • • • •153 1-5/16” x 2-3/8” • • • • • • •154 1-1/4” x 1-3/4” •157 3/4” x 1-1/4” • • • • • • • •158 3/4” x 1-3/4” • • • • • • • •
MULLION Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend162 3/8” x 1-5/8” •164-1-1/8 3/8” x 1-1/8” • • • • •164-1-3/8 3/8” x 1-3/8” • • • • 164-1-5/8 5/8” x 1-5/8” • •165 1/2” x 1-1/2” • •
PILASTER Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend171 3/4” x 6” • • •
BAR RAIL Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend179 1-3/4” x 5-1/4” • • •179B 1-3/4” x 7-1/4” •
www.brenlo.ca
TM
11
Species Chart
CHAIR RAIL Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend181 1” x 3-5/8” • •186 3/4” x 3” • • •187 5/8” x 2-1/2” • • • • • •189 1” x 2-1/2” • • • • • •189A 1-5/16” x 2-1/2” • 3/8" rabbet2180 7/8” x 3-1/8” •2188 13/16” x 3-1/8” •
GLASS BEAD Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend190 1/2” x 9/16” • • • •191 3/8” x 3/8” • • • • • • •
SHELF EDGE Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend195 3/8” x 3/4” • • • •197 1/4” x 3/4” • • •
CORNER GUARD Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend200 1-5/16” x 1-5/16” • •201 1-1/8” x 1-1/8” • •204 3/4” x 3/4” • •
HALF ROUND Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend205 3/4” x 1-1/2” • • • • • •205A 1” x 2” • • • • •205B 1-1/4” x 2-1/2” •205C 1-1/2” x 3” •205D 1-3/4” x 3-1/2” •206 1/2” x 1” • • • •207 3/8” x 3/4” • • • • •
BASE SHOE Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend208 1/2” x 3/4” • • • • • • • •209 1/2” x 7/8” •210 1/2” x 3/4” • •469 1/2” x 3/4” • •
ASTRAGAL Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend211 3/4” x 1-3/4” • • • • •212 3/4” x 1-3/8” • • • • • • •213 7/16” x 3/4” • • • • • • •
T ASTRAGAL Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine EZ Bend215 1-1/4” x 2-7/16” • • Size W/W
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
12
STOOL Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine White Oak EZ Bend227 1-5/16” x 2-3/4” • • • • • •228 1-1/16” x 2-1/4” • • •229 1-1/16” x 3-1/4” • •230 1-1/16” x 4-1/4” • • • • • •231 1-1/16” x 5-1/4” •232 1-1/16” x 7-3/4” •MK 1-3/4” x 3-1/2” •
MISC Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine White Oak EZ Bend225 11/16” x 1-3/4” • Picture Rail
HANDRAIL Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine White Oak EZ Bend903 1-5/8” x 2-3/4” •904 1-5/8” x 2-3/4” • •930 1/4” x 1-5/16” •
D4S Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine White Oak EZ BendD4S.5-2 1/2” x 1-1/2” • • • • •D4S.5-4 1/2” x 3-1/2” • • • • • • •D4S.5-6 1/2” x 5-1/2” • • • • • • •D4S11 3/4” x 3/4” • • •D4S12 3/4” x 1-1/2” • • • • • • • •D4S13 3/4” x 2-1/2” • • • • •D4S14 3/4” x 3-1/2” • • • • • • • • •D4S15 3/4” x 4-1/2” • •D4S16 3/4” x 5-1/2” • • • • • • • • •D4S18 3/4” x 7-1/4” • • • • • • •D4S110 3/4” x 9-1/4” • • • • •D4S112 3/4” x 11-1/4” • • •D4S1.25-2 1-1/4” x 1-1/4” •D4S1.25-4 1-1/4” x 3-1/2” • •D4S1.25-6 1-1/4” x 5-1/2” • •D4S22 1-1/2” x 1-1/2” • • • • •D4S24 1-1/2” x 3-1/2” • • • • •D4S26 1-1/2” x 5-1/2” • • • • •D4S28 1-1/2” x 7-1/4” • • • •D4S210 1-1/2” x 9-1/4” • • •D4S212 1-1/2” x 11-1/4” • • •
JAMBS Size W/W Oak Pine Maple Cherry Mahog Walnut K. Pine White Oak EZ Bend4.625 3/4” x 4-5/8” • • • • • • • •4.875 3/4” x 4-7/8” • • •6.625 3/4” x 6-5/8” • • • • • • •6.875 3/4” x 6-7/8” • • •
5.5 1-1/2” x 5-1/2” • Rabbeted for 1-3/4” door
www.brenlo.ca
TM
13
Section 1-1
Casings
7A - 3/4" (20 mm) x 2-3/4" Corresponding Baseboards#349, #349A
1A - 3/4" (20 mm) x 3-1/2"Corresponding Baseboards#42B, #42C
1 - 3/4" (20 mm) x 2-3/4" Corresponding Baseboards#42, #42B
7 - 3/4" (20 mm) x 3-1/2" Corresponding Baseboards#349, #349B
4 - 7/8" (22 mm) x 3" Corresponding Baseboards#349, #53
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
14
Section 1-2
Casings
15B - 3/4" (20 mm) x 3-1/4"Corresponding Baseboard#312
15 - 3/4" (20 mm) x 2-3/4" Corresponding Baseboard#312
19A - 3/4" (20 mm) x 2-3/4" Corresponding Baseboard#353A
19 - 3/4" (19 mm) x 4-1/4" Corresponding Baseboards#353B, #354
www.brenlo.ca
TM
15
25S - 3/4" (20 mm) x 2-1/2"Corresponding Baseboard #25B
Section 1-3
Casings
23 - 3/4" (20 mm) x 3-1/16" Corresponding Baseboard #358
22 - 3/4" (20 mm) x 3-1/2" Corresponding Baseboards#53, 1 x 8
25A - 3/4" (20 mm) x 3-1/2"Corresponding Baseboard #25C
20B - 3/4" (20 mm) x 3-1/2"Corresponding Baseboard #354
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
16
Section 1-4
Casings
101 - 3/4" (20 mm) x 3-1/2"Corresponding Baseboards #306, 307, 307C
102 - 3/4" (20 mm) x 3-1/2"Corresponding Baseboard #302C
103- 3/4" (20 mm) x 3-1/2"Corresponding Baseboards #306, 1” x 8”
www.brenlo.ca
TM
17
Section 1-5
Casings
800 - 7/8" (22 mm) x 3-1/2" Corresponding Baseboard#352B
106A - 3/4" (20 mm) x 2-3/4" Corresponding Baseboard#307
600 - 1-1/8" (29 mm) x 3" Corresponding Baseboard#25B
500 - 1-1/8" (29 mm) x 3"Corresponding Baseboard#42B
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
18
Section 1-6
Casings
888 - 3/4” x 2-3/4”Corresponding Baseboards #42B, #349
810 - 3/4” (20 mm) x 3-1/2” Corresponding Baseboard #820
810e - 3/4” (20 mm) x 3-1/2” Corresponding Baseboard #820e
www.brenlo.ca
TM
19
Section 2-1
Casings/Back Band
30 - 1-5/8" x 1-5/8" (20mm Rabbet)
701 - 1-1/8" x 1-1/2" (22mm Rabbet)
37 - 3/4" x 1-5/16" (20mm Rabbet)
106 - 3/4" (20 mm) x 3-1/2" Corresponding Baseboard#306 or #307C
700 - 7/8" (22 mm) x 3-1/2" 700B - 7/8" (22 mm) x 3"Corresponding Baseboard #900, 900C, 900D
20 - 3/4" (20 mm) x 2-3/4" Corresponding Baseboard #354
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
20
Section 2-2
In StockDesigner Series Casing/Back band
2006 - 1-5/16" x 2-1/4"BACK BAND
2005 - 5/8" (16 mm) x 2-5/8" CASING
2001 - 1-13/16" x 2-3/4" BACK BAND
2000 - 11/16" (18 mm) x 3-1/8" CASING
3/4" (19mm)
11/16" (18mm)
9/16" (14mm)
5/8" (16mm)
www.brenlo.ca
TM
21
Section 2-3
In StockDesigner Series Casing/Back band
2011 - 1-5/16" x 2-1/8" BACK BAND
2010 - 1" (25 mm) x 4-1/2" CASING
2016 - 1-3/4" x 1-1/2" BACK BAND
2015 - 3/4" (19 mm) x 3-1/2" CASING
1/2" (13mm)
3/4" (19mm)
5/8" (16mm)
1" (25mm)
www.brenlo.ca
TM
23
36 - 1-3/32" x 1-5/8" (20mm Rabbet)
1/4"
3/4" (20mm)
Section 3-1
Back Bands
30 - 1-5/8" x 1-5/8" (20mm Rabbet)
34 - 13/16" x 1-3/8" (3/4" (20mm) Rabbet)34 Ext. - 13/16" x 1-1/2" (7/8" (22mm) Rabbet)
35 - 7/8" x 1-5/8" (3/4" (20mm) Rabbet)35 Ext. - 7/8" x 1-3/4" (7/8" (22mm) Rabbet)
37 - 3/4" x 1-5/16" (20mm Rabbet)
32A - 1-1/4" x 2-1/32" (20mm Rabbet)
1/4"
3/4" (20mm)7/8" (22mm)
1/4"
3/4" (20mm)7/8" (22mm)
1/4"
3/4" (20mm)
1/4"
3/4" (20mm)
1/4"
3/4" (20mm)
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
24
Section 3-2
Back Bands
46 - 1-5/16" x 1-9/16" (22mm Rabbet)
1/4"
7/8" (22mm)
701 - 1-1/8" x 1-1/2" (22mm Rabbet)
5/8"
7/8" (22mm)
39 - 7/8" x 1-1/2" (22mm Rabbet)38 - 13/16" x 1-3/8" (22mm Rabbet)
1/4"
3/4" (20mm)
1/4"
3/4" (20mm)
www.brenlo.ca
TM
25
Section 4-1
Plinth Blocks
* Plinth Blocks in this section, run in lineal foot lengths andare designed to be cut to length at job site.
*338 - 1-3/4" x 4-3/8" Accommodates 3-1/2" Casing& #34 Back band
*339 - 7/8" x 4-1/2" Accommodates #19 Casing
*735 - 1-15/16" x 4-7/16"Accommodates 3-1/2"Casing & #35 Back band
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
26
2012 - 2-3/8" x 5-5/8" PLINTHFor 2011 Back Band and 2010 Casing
2017 - 2" x 4-7/8" PLINTHFor 2016 Back Band and 2015 Casing
Section 4-2
In StockDesigner Series Plinth Block
www.brenlo.ca
TM
27
Section 4-3
In StockDesigner Series Plinth Blocks
2002 - 2-1/4" x 5-1/2" PLINTHFor 2001 Back Band and 2000 Casing
2007 - 1-11/16" x 4-5/8" PLINTHFor 2006 Back Band and 2005 Casing
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
28
*2030B - 1-3/4” x 5-1/8”Accommodates #20B & Back band #30
*2030 - 1-3/4” x 4-3/8”Accommodates Casing #20 & Back band #30
Section 4-4
In Stock
Designer Series 2000 Plinth Blocks
www.brenlo.ca
TM
29
Section 5-1
Plinth Blocks andCorner Blocks
65 - 7/8" x 3" x 3" 66 - 1" x 4-1/2" x 4-1/2"66A - 1" x 3-3/4" x 3-3/4"
67 - 1-3/8" x 4-1/2" x 4-1/2" 67A - 1-3/8" x 3-3/4" x 3-3/4"68 - 1-5/16" x 3" x 3"
337 - 1-3/8" x 20" x 4-1/2" 337 - 1-3/8" x 20" x 3-3/4"337 - 1-5/16" x 16" x 3"
www.brenlo.ca
TM
31
Section 6-1
Baseboards
25B - 3/4" (19 mm) x 5-1/2" 25C - 3/4" (19 mm) x 7-1/4" Corresponding Casing#25S or #25A
53 - 3/4" (19 mm) x 5-1/2”Corresponding Casing#4, #22 or #23
42 - 3/4" (19 mm) x 4-1/2" 42B - 3/4" (19 mm) x 5-1/2" 42A - 3/4" (19 mm) x 6-1/2" 42C - 3/4" (19 mm) x 7-1/4"Corresponding Casing#1 or #1A
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
32
307 - 3/4" (19 mm) x 5-1/2"307C - 3/4" (19 mm) x 7-1/4"Corresponding Casing #106
306 - 3/4" (19 mm) x 7-1/4"Corresponding Casing #106
Section 6-2
Baseboards
302C - 3/4" (19 mm) x 7-1/4"Corresponding Casing #102
www.brenlo.ca
TM
Section 6-3
Baseboards
3093/4" (19 mm) x 8-1/2"Corresponding Casing # 2005 & 2006
NEW
31013/16" x 8-1/2"Corresponding Casing # 106
33
3083/4" (19 mm) x 8-1/2”Corresponding Casing #102
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
34
Section 6-4
Baseboards
312 - 11/16" x 4-1/4"Corresponding Casing #15
356A - 3/4" (19 mm) x 6-1/2"Corresponding Casing #800
www.brenlo.ca
TM
35
Section 6-5
Baseboards
349A - 3/4” (19 mm) x 4 -7/8" 349 - 3/4" (19 mm) x 5-1/2"349B - 3/4" (19 mm) x 7-1/4"Corresponding Casing #7A or #7
352 - 3/4” (19 mm) x 6 -1/2"352B - 3/4" (19 mm) x 7-1/4" Corresponding Casing #1A or #800
353B - 3/4" (19 mm) x 7-1/4" Corresponding Casing#19 or #19A
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
36
Section 6-6
Baseboards
354 - 3/4” (19 mm) x 7-1/4"Corresponding Casing #20
358 - 3/4” (19 mm) x 5-1/2" Corresponding Casing #23
www.brenlo.ca
TM
37
Section 6-7
Baseboards
820 - 3/4” (19 mm) x 7-1/4” Corresponding Casing#810
820E - 3/4” (19 mm) x 7-1/4”Corresponding Casing#810E
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
38
910 - 13/16" x 9-1/4" Corresponding Casing #700 or #700B
Section 6-8
900 - 7/8” (22 mm) x 5-1/2"900A - 7/8” (22 mm) x 6 -1/2"900C - 7/8" (22 mm) x 7-1/4"900D - 7/8" (22 mm) x 8-1/2"Corresponding Casing #700 or #700B
157 - 3/4” x 1-1/4"
NEW
Baseboards
www.brenlo.ca
TM
39
In StockDesigner Series
Baseboards
2053D - 1" (25.4 mm) x 8-1/2"Corresponding Casing #2010 or #2015
2051C - 7/8" (22 mm) x 7-1/4" 2051D - 7/8" (22 mm) x 8-1/2" Corresponding Casing #2000, #2005
Section 6-9
TM
41
Section 7-1
70B - 3/4” x 7"
A = PROJECTIONB = HEIGHT
70 (A = 3-11/16")(B = 3-11/16")
70C (A = 6")(B = 6")
70B (A = 4-15/16")(B = 4-15/16")
B
A
70C - 7/8" x 8-1/2"
Crown Moulds
70 - 3/4” x 5-1/4"
www.brenlo.ca
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
42
Section 7-2
Crown Moulds
72 - 3/4” x 3-1/2" 72B - 3/4” x 4-1/4"
A = PROJECTIONB = HEIGHT
71 (A = 2-15/16")(B = 2-15/16")
72 (A = 2-1/2")(B = 2-1/2")
72B (A = 3")(B = 3")
72C (A = 3-11/16")(B = 3-11/16")
B
A
71 - 3/4” x 4-1/4"
72C - 3/4" x 5-1/4"
www.brenlo.ca
TM
43
Section 7-3
Crown Moulds
A = PROJECTIONB = HEIGHT
73 (A = 4-5/8")(B = 4-1/4")
507 (A = 3-5/16")(B = 4-3/8")
509 (A = 2-9/16")(B = 2-11/16")
B
A
507 - 7/8” x 5-1/2"
73 - 3/4” x 6-1/4"
509 - 13/16” x 3-11/16"
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
44
Section 7-4
Crown Moulds
520 - 3/4" x 4"
A = PROJECTIONB = HEIGHT
520 (A = 2-11/16")(B = 3")
523 (A = 1-5/8")(B = 1-5/8")
B
A
523 - 3/4” x 2-3/8”
www.brenlo.ca
TM
45
Section 7-5
Crown Moulds
535 - 3/4” x 3-1/2”
A = PROJECTIONB = HEIGHT
535 (A = 2-1/2")(B = 2-1/2")
549 (A = 2-15/16")(B = 2-15/16")
B
A
549 - 13/16" x 3-1/4"
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
46
Section 7-6
552 - 13/16" x 5-3/16"
573 - 1-1/4" x 5-1/2"
578 - 1" x 4-3/4"
A = PROJECTIONB = HEIGHT
552 (A = 3-1/2")(B = 3-13/16")
573 (A = 3-3/4")(B = 3-3/4")
578 (A = 3-1/4")(B = 3-3/8")
B
A
Crown Moulds
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
48
Section 8-2
Bolections & Aprons
88 - 1-1/4" x 3-1/4" 89 - 1-5/16" x 3-1/4"
81 - 1-5/16" x 3-1/4" 82 - 1-3/4" x 4"
www.brenlo.ca
TM
49
Section 9-1
Cove Moulds
90 - 1/2” x 1/2" 91 - 3/4” x 3/4"
92 - 1” x 1"
94 - 3/4" x 3-1/2"
93 - 1-1/4” x 1-1/4"
A = PROJECTIONB = HEIGHT
94 (A = 2-1/2")(B = 2-1/2")
B
A
95 - 5/8" x 5/8"
www.brenlo.ca
TM
51
Section 10-1
Cap Moulds
96 - 3/4” x 1-3/8"
3/4"
1/4"
97 - 9/16" x 1-1/8"
3/4"
1/4"
98 - 3/4” x 1-3/4"
1/2"
3/8"
www.brenlo.ca
TM
53
Section 11-1
Door Stops
108 - 1-5/8” x 7/16”
110 - 1-3/8” x 3/8"
111 - 1-3/4” x 7/16"
116 - 1-3/4" x 7/16"113 - 1-3/4” x 7/16"
117 - 2-1/2” x 1/2"
www.brenlo.ca
TM
55
Section 12-1
Panel Moulds & Base Caps
118 - 7/16" x 3/4" 119 - 1/2" x 1-1/16"
121 - 11/16" x 1-3/8"
124 - 3/4" x 2-1/4"
122A - 7/16" x 1-1/8"
122B - 3/4" x 2-3/16"
122 - 5/8" x 1-9/16"
123 - 9/16" x 1-3/4"
NEW
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
56
Section 12-2
Panel Moulds & Base Caps
125 - 1-1/16" x 1-1/2"
126 - 1/2" x 1-5/8"
327 - 1/2" x 1-3/4" 328 - 7/16" x 1-5/16"
129 - 3/8" x 1" 134 - 3/8" x 11/16"
329 - 3/8" x 1-1/8"
www.brenlo.ca
TM
57
Section 12-3
Panel Moulds & Base Caps
620 - 1/2" x 1-1/4"
648 - 3/4" x 2-1/4"645 - 11/16" x 2-1/2"
666 - 1/2" x 7/8"
649 - 3/4" x 1-3/4"
608 - 7/16” x 11/16"
NEW
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
58
1/2"
632 - 7/8" x 1-1/2"
1/2"
133 - 13/16” x 1-3/8”
Section 12-4
131 - 5/8" x 1"
130 - 1" x 1-1/4"
132 - 1-1/4" x 1-5/8"
130s - 7/8" x 1"
3/4"
3/4"
1/2"
1/4"
Panel Moulds
651 - 7/8” x 3”
1/2"1/2"
7/16” 1/2"
652 - 7/8” x 3”
www.brenlo.ca
TM
59
Section 13-1
Bed Moulds &Quarter Rounds
141 - 1" x 1"
143 - 5/8" x 5/8" 144 - 1/2" x 1/2"
142 - 3/4" x 3/4"
138 - 5/8" x 1-5/8"
136 - 5/8" x 2-1/4"135 - 5/8" x 2-3/4"
A = PROJECTIONB = HEIGHT
135 (A = 1-7/8")(B = 2")
136 (A = 1-7/16")(B = 1-3/4")
138 (A = 1-1/8")(B = 1-3/16")
B
A
www.brenlo.ca
TM
61
Section 14-1
T-Astragals, Battens, Fascias,Window Mullions
150 - 9/16" x 2-1/4"
162 - 3/8" x 1-5/8" 164 - (3/8" thick) 165 - 1/2" x 1-1/2"widths of:1-1/8"1-3/8"
151 - 3/4" x 1-5/8"
215 - 1-1/4" x 2-7/16"
1-13/16"
3/8"
www.brenlo.ca
TM
63
Section 15-1
Brick Mould andShingle Moulds
152 - 1-7/32" x 1-11/16"
157 - 3/4" x 1-1/4"
158 - 3/4" x 1-3/4"
153 - 1-5/16" x 2-3/8"
154 - 1-1/4" x 1-3/4"
www.brenlo.ca
TM
67
Section 17-1
Chair Rail
187 - 5/8" x 2-1/2" 189 - 1" x 2-1/2" 189A - 1-5/16" x 2-1/2"
181 - 1" x 3-5/8"
1/2"
(13mm)
3/8"(10mm)
186 - 3/4" x 3"
www.brenlo.ca
TM
69
Section 18-1
Glass Beads, Shelf Edges,Corner Guards
190 - 1/2" x 9/16"
195 - 3/8" x 3/4"
201 - 1-1/8" x 1-1/8"
204 - 3/4" x 3/4"
197 - 1/4" x 3/4"
200 - 1-5/16" x 1-5/16"
191 - 3/8" x 3/8"
13/16"
13/16"
15/16"
15/16"
www.brenlo.ca
TM
71
Section 19-1
Half RoundsBase Shoe and Flat Astragals
208 - 1/2" x 3/4"
211 - 3/4" x 1-3/4"212 - 3/4" x 1-3/8"
209 - 1/2" x 7/8" 210 - 1/2" x 3/4"
206 - 1/2" x 1" 207 - 3/8" x 3/4"
213 - 7/16" x 3/4"
469 - 1/2" x 3/4"
205 - 3/4" x 1-1/2" 205A - 1" x 2”205B - 1-1/4" x 2-1/2"205C - 1-1/2" x 3"205D - 1-3/4" x 3-1/2"
www.brenlo.ca
TM
73
Section 20-1
Window Stool
MK - Stool - 1-3/4" x 3-1/2"3/4" (19mm)
3/4" (19mm)
#227 1-5/16" x 2-3/4"
228 - Window Stool 1-1/16" x 2-1/4"229 - Window Stool 1-1/16" x 3-1/4"230 - Window Stool 1-1/16" x 4-1/4"231 - Window Stool 1-1/16" x 5-1/4"232 - Window Stool 1-1/16" x 7-3/4"*Note: All profiles stocked without rabbet.
Please inquire for rabbet.
TM
75
Section 21-1
Bar Rail
179 - 1-3/4" x 5-1/4"
2-11/16"
15/16"
2-5/8"
179B - 1-3/4" x 7-1/4"
2-11/16"
7/8"
3-9/16"
www.brenlo .ca
www.brenlo.ca
TM
77
Section 22-1
Tongue & Groove Paneling
146 - 3/4" (19mm) x 3-1/2" 3.69 LF = 1 sq. ft. coverage
145B - 1/2" (13 mm) x 5-1/2" 2.29 LF = 1 sq. ft. coverage
146A - 3/4" (19mm) x 4-3/4" - Poplar only 2.67 LF = 1 sq. ft. coverage
146B - 3/4" (19mm) x 5-1/2" 2.28 LF = 1 sq. ft. coverage
145S - 3/8" (9 mm) x 3-1/8" REVERSIBLE- 4.17 LF = 1 sq. ft. coverage
145 - 3/8" (9mm) x 3-1/8" REVERSIBLE 4.17 LF = 1 sq. ft. coverage
www.brenlo.ca
TM
79
Section 23-1
Miscellaneous
L1 - Architrave 1-3/4" x 4-3/4"
225 - Picture 11/16" x 1-3/4"
903 - 1-5/8" x 2-3/4"
904 - 1-5/8" x 2-34"
930 - 1/4" x 1-5/16"
149 - Nosing 1" x 3-1/2"1/4" (6mm)
2-5/16"
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
80
Section 23-2
Miscellaneous
147 - 13/16" x 5-1/2" THRESHOLD (3' OAK IN STOCK)
3/8" (10mm)
7/16" (11mm)
1-13/16" (46mm)
DRESSED FOUR SIDES SQUARE STOCK:1/2 x 2 1/2 x 4 1/2 x 6(1/2" x 1-1/2") (1/2" x 3-1/2") (1/2" x 5-1/2")
1 x 2 1 x 3 1 x 4 1 x 5 1 x 6 1 x 8(3/4" x 1-1/2") (3/4" x 2-1/2") (3/4" x 3-1/2") (3/4” x 4-1/2”) (3/4" x 5-1/2") (3/4" x 7-1/4")
1 x 10 1 x 12(3/4" x 9-1/4") (3/4" x 11-1/4")
6/4 x 2 6/4 x 4 6/4 x 6(1-1/4" x 1-1/4") (1-1/4" x 3-1/2") (1-1/4" x 5-1/2")
2 x 2 2 x 4 2 x 6 2 x 8(1-1/2" x 1-1/2") ( 1-1/2" x 3-1/2") (1-1/2" x 5-1/2") (1-1/2" x 7-1/4")
2 x 10 2 x 12(1-1/2" x 9-1/4") (1-1/2" x 11-1/4")
BEVELED JAMB STOCK:3/4" x 4-5/8" 3/4" x 4-7/8" 3/4"x 6-5/8" 3/4" x 6-7/8"
SINGLE RABBETED JAMBS:1-1/2" x 5-1/2" (Rabbet size 1/2" x 1-13/16")
AVAILABLE IN AMERICAN POPLAR, OAK, SELECT PINE, MAPLE, CHERRY, MAHOGANY, WALNUT & KNOTTY PINE
Custom sizes of D4S available by special request.
www.brenlo.ca
TM
81
Section 24-1
Designer Series CasingsNon-stock items, available upon request
2 - 3/4" (20 mm) x 2-3/4"
6 - 3/4" (20 mm) x 3-1/2"
8 - 1-1/16" (27 mm) x 4"
5- 7/8" (20 mm) x 4"
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
82
37 - 3/4" x1-5/16" (20mm Rabbet) 107 - 3/4" (20 mm) x 3-1/2"
Section 24-2
Designer Series CasingsNon-stock items, available upon request
9 - 1-1/16" (27 mm) x 4"
321 - 3/4" (20 mm) x 2-3/4"
31 - 1-3/4" x 1-7/8"(20mm Rabbet)
21 - 3/4" (20 mm) x 4-1/4"
www.brenlo.ca
TM
83
41 - 3/4" (19 mm) x 4-1/2"
44 - 3/4" (19 mm) x 5-1/2"
49 -3/4" (19 mm) x 7-1/4"
Section 24-3
Designer Series BaseboardsNon-stock items, available upon request
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
84
54 - 3/4" (19 mm) x 7-1/4" 59A - 3/4" (19 mm) x 7-1/4" 2050 - 1-1/16" (27 mm) x 8-3/4"Corresponding Casing #2000
Section 24-4
Designer Series BaseboardsNon-stock items, available upon request
www.brenlo.ca
TM
85
Section 24-5
Designer Series BaseboardNon-stock items, available upon request
2052 - 1-1/4" (32 mm) x 9-1/4"Corresponding Casing #2010
2053C - 1" (25.4 mm) x 7-1/4"Corresponding Casing #2015
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
86
Section 24-6
Designer Series Crown MouldsNon-stock items, available upon request
73A - CROWN MOULD 3/4” x 5-1/4"
577 - CROWN MOULD 1-5/16” x 6-7/8"
A = PROJECTIONB = HEIGHT
73A (A = 3-7/8")(B = 3-1/2")
577 (A = 3-11/16")
(B = 5-3/4")
B
A
www.brenlo.ca
TM
87
Section 24-7
Designer Series MiscellaneousNon-stock items, available upon request
115 - DOOR STOP 1/2" x 1-3/4"
182 - CHAIR RAIL 1-1/16" x 3-1/8" 183 - CHAIR RAIL 1" x 3"
128 - PANEL MOULD 9/16" x 1-1/8"
127 - PANEL MOULD 3/4" x 1-5/8"
155 - TEAR DROP 1" x 1"
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
88
Section 24-8
Designer Series MiscellaneousNon-stock items, available upon request
87 - BOLECTION 1-5/16" x 4-7/8" 185 - CHAIR RAIL 1-1/16" x 5-7/8"184 - CHAIR RAIL 1-1/16" x 3-7/8"
www.brenlo.ca
TM
89
Section 24-9
Designer Series MiscellaneousNon-stock items, available upon request
2080 - 1-5/16" x 3-1/4" 2081 - 1-5/16" x 3-1/4"
www.brenlo.ca
TM
91
Section 25-1
Signature Series
2100 - CASING 1-5/16" x 4-1/2"
2108 - CASING 1-5/16" x 1-1/2"
2130 - PLINTH 1-1/2" x 4-7/8"
STOCK ITEM
STOCK ITEM
STOCK ITEM
NEW PROFILES
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
92
Section 25-2
2140 - BASEBOARD 3/4" x 8-1/2"Corresponding Casing #2100 - 1-5/16” x 4-1/2”
2148 - BASEBOARD 13/16" x 9-1/4"Corresponding Casing #2108 1-5/16” x 1-1/2”
Signature SeriesNEW PROFILES
www.brenlo.ca
TM
93
Section 25-3
2150 - CROWN 7/8" x 6-1/2"
2158 - CROWN 7/8" x 6-1/2"Non-stock item, available uponrequest
2156 - CROWN 7/8" x 6-1/2"
Non-stock item, available upon request
STOCK ITEM
NEW PROFILES
Signature Series
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
94
Section 25-4
2180 - CHAIR RAIL 7/8" x 3-1/8" 2188 - CHAIR RAIL 13/16" x 3-1/8"
Signature Series
NEW PROFILES
www.brenlo.ca
TM
95
MDF - Step Casing#8031 - 3/4" x 3-1/2"
MDF - Colonial Base#8095 - 1/2" x 5-1/4"#8915 - 1/2" x 7-1/4"
MDF - Step Base#8235 - 5/8" x 7-1/8"
MDF - Colonial Casing#8954 - 3/4" x 3-1/2"
Section 26-1
MDF Profiles
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
98
Section 27-2
Crown Combinations
BASEBOARD 42
CROWN 70
1x3(3/4"x2-1/2")ACTUAL)
BED MOULD 136
1-1/2"x2-1/2"(ACTUAL)
www.brenlo.ca
TM
99
Section 27-3
Crown Combinations
2"x2"(1-1/2"x1-1/2"ACTUAL)
CROWN 70
1"x6" (3/4"x5-1/2"ACTUAL)
PANEL MOULD 132
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
100
Section 27-4
Crown Combinations
CROWN 72
1"x6" (3/4"x5-1/2"ACTUAL)
PANEL MOULD 132
HALFROUND207
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
102
Section 27-6
Crown Combinations
BASEBOARD 42
BASEBOARD 42
CROWN 70
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
104
Section 27-8
Crown Combinations
BRICKMOULD152
BRICKMOULD153
2"X2"(1-1/2"X1-1/2"ACTUAL)
CROWN 70
DOORSTOP113
BASEBOARD 349
www.brenlo.ca
TM
105
Section 27-9
Crown Combinations
CROWN 72C
BASEBOARD 349
BASEBOARD 349CROWN 71
2”X2”(1-1/2" X 1-1/2"ACTUAL)
PANEL MOULD125
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
106
Section 27-10
Crown Combinations
CROWN 72C
BASEBOARD 349 BEDMOULD
135
1"X4"(3/4"X3-1/2"ACTUAL)
PANEL MOULD121
HALFROUND207
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
108
Section 27-12
Apron & Sill Combinations
STOOL 228
SHINGLE 158
STOOL 229
CASING 7
www.brenlo.ca
TM
109
Section 27-13
Apron & Sill Combinations
STOOL 229
CASING 20
STOOL 229
DOOR STOP 111
BACK BAND 35 EXT.
CASING 800
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
110
Section 27-14
Apron & Sill Combinations
STOOL 228
BRICK MOULD 153
MK STOOL
BOLECTION 88
www.brenlo.ca
TM
111
Section 27-15
Beam & Ceiling Combinations
BEAM
BEAM
BEAMS CROWN 71
SHINGLE 157
PICTURERAIL 225
1"X4"BEAMS
1"X4"BEAM 1"X4"
BEAM COVE 94
WALL
CORNER GUARD 201
BRICKMOULD152
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
112
Section 27-16
Beam & Ceiling Combinations
BEAM
BEAM
BEAM
BEAM
COVE 92 / 93
COVE 90
COVE 94
COVE 92 / 93
www.brenlo.ca
TM
113
Section 27-17
Moulding Combinations
BASEBOARD25B
CASING 25S
BASEBOARD307
CASING 106
BASEBOARD25B
CASING 23
CASING 700/700B
BACK BAND 701
BASEBOARD900/900A/900C/900D
SHOE 157Note: Some items arenon-stock, availableupon request.
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
114
Section 27-18
Moulding Combinations
CASING 20 CASING 20
BACK BAND 30
BACK BAND 34
CASING 321 DS
BACK BAND 35
CASING 6 DS
BASEBOARD44 DS
CHAIR RAIL189
CHAIR RAIL186
BASEBOARD356A
BASEBOARD349
BASEBOARD 53
BACK BAND 30
BASESHOE
210
www.brenlo.ca
TM
115
Section 27-19
Moulding Combinations
CHAIR RAIL 187
BASEBOARD 41 DS
BASEBOARD 49 DS
BASESHOE
111
BASEBOARD 54 DS
CHAIR RAIL 183 DSBACK BAND 31 DS
CASING 21 DS
CASING 9 DS
CASING2 DS
CASING8 DS
BASEBOARD 54 DS
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
116
Section 27-20
Moulding Combinations
CHAIR RAIL184 DS
BASEBOARD2053 DS
BACK BAND2016 DS
CASING 2015 DS
BASEBOARD306
BACK BAND37
CASING 106
BASEBOARD2052 DS
BASE SHOE111
BACK BAND2011 DS
CASING 2010 DS
www.brenlo.ca
TM
117
Section 27-21
Moulding Combinations
CORNERBLOCK 67
BASEBOARD353B
BASEBOARD42 / 42A / 42B / 42C
BASEBOARD352
BASEBOARD 25B
PLINTHBLOCK337
CASING19 / 19A
CASING1 / 1A CASING
800
BACK BAND35 EXT.
CASING600
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
118
Section 27-22
Moulding Combinations
BASEBOARD25C
BASEBOARD42C
CHAIRRAIL187
CASING 1/1A
CASING700/700B
BASEBOARD900/900A/900B/9000D
BASESHOE
157
BACK BAND 35
BACK BAND35 EXT.
BASEBOARD42B
BASESHOE
208
BASESHOE
110
BACK BAND37
BACK BAND35
CASING 25A
CASING 1 / 1A
www.brenlo.ca
TM
119
Section 27-23
Moulding Combinations
BASEBOARD349
BASEBOARD900C
PLINTH BLOCK735
BASEBOARD42C
BASEBOARD2140
CHAIRRAIL 82
BASESHOE
110
BACK BAND35
BACK BAND35 EXT.
BACK BAND32A
CASING 7/7A
CASING 700
CASING 1/1A
CHAIR RAIL2180
PLINTH BLOCK2130
CASING 2100
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
120
Section 27-24
Moulding Combinations
PLINTH BLOCK2130
BASEBOARD2148
CHAIRRAIL181
BASEBOARD2050 DS
BASEBOARD2051 DS
CHAIR RAIL2188
BACK BAND2001 DS
BACK BAND2006 DS
CASING 2108
CASING 2000 DS
CASING 2005 DS
www.brenlo.ca
TM
121
Custom Manufacturing
Over the years Brenlo has become much more than just a wood moulding manufacturer. We focus on creatinga unique product for our customers and in turn their clients. Our Custom Shop takes great pride in theseproducts and solutions while in keeping with the vision of the project. We have once again expanded ourmanufacturing capabilities with the latest technology. We remain true to great craftsmanship and attention todetail. We now offer more Joinery and Bench-work type products. Some of the new products available are ourspecialty doors, over-sized porch brackets, courtroom and church pew components, solid wood laminatedtable/counter tops, machined doors and jambs, C.N.C parts and components for the Store Fixture Industry.
Don't forget that curved mouldings and trims are our specialty.
Please call us for your next unique and challenging project; we can help you with it.
If it's made of wood we can do it!
Section 28-1
Custom Shop
This publication, design profile, profile codes and logos are protected by copyright and trademark laws under Canada and International law. All rights reserved. © 2010 Brenlo Ltd.
TM
122
chord(span)
VERTICAL CURVES
HORIZONTAL CURVES
rise(off set)
Top View
Section 28-2
Arches & Curves
Arches and Curves: Brenlo specializes in curved casings, back bands, crowns, baseboards, bar rails, chair rails and panel moulds.
Curves can be made from a template or from accurate measurements. Arches made from measurements for window casings tendto be the most accurate as they give a true consistent radius, ie. length of a radius.
Typical arch types are as follows:
Symmetrical Arch Elliptical Arch Full Circle Arch Half Circle Arch(Segment of a circle)
Please note all horizontal curves must be clearly specified as concave or convex applications.
Concave Curve Convex CurveProfile is on the inside Profile is on the outside
of the curve of the curve
How to measure curvesTo make an arch window casing you need to have only two critical measurements. These measurements are as follows:1) The accurate chord (inside width) of the casing line2) The accurate rise (height) from your horizontal line (chord) to the inside of your casing line.
For a cost effective alternative, we also offer some profiles custom run in EZ Bend.
top related