1 ns1000 v4.0 - summary - rev1.0r 6 june, 2014. 2 v4 key feature enhancement list #items 1. new ipcs...

Post on 25-Dec-2015

219 Views

Category:

Documents

2 Downloads

Preview:

Click to see full reader

TRANSCRIPT

1

NS1000 V4.0

- Summary -

Rev1.0r 6 June, 2014

2

V4 Key Feature Enhancement List

# Items

1. New IPCS KX-NS0154

1-1 LAN sync

1-2 Easy Installation

1-3 Survey tool

1-4 Other

2. Small Call Center Feature Enhancement

2-1-1 Call Pickup Group Monitor

2-1-2 Queue position anouncement

3. Remote Worker Feature Enhancement

3-1 EXT Busy status

4. Boss Secretary Feature Enhancement

4-1 Remote Call Forward On/Off

3

V4 Key Feature Enhancement List

# Items

5. Web-Maintenance Console Enhancement

5-1 Dsys converter for Slave unit

5-2 Dsys converter for UM

5-3 EXT list order

6. Other Features

6-1 IP address Redundancy for SIP trunk

6-2 Call waiting tone for EHS headset

6-3 SLT pre-ringing

4

1. New IPCS KX-NS0154

5

New IPCS KX-NS0154

General• Site planning condition is almost same as Legacy CS, so NS0154

can be Plug and Play CS with LAN Synchronization..• No synchronization tree concept for LAN synchronization. Direct

synchronization with master CS via LAN. • Mixed installation with NCP0158 or Legacy CS and NS0154 must be

done by AIR synchronization.  • NS0154 supports up to 4 channels talk path by default. It can

possible to expand the channel to 8 by installing activation key.

Items Number

Maximum number of IP-CS per Unit 64

Maximum number of IP-CS on One-look-networking (Total number)

128

Maximum number of IP-CS as member of a LAN synchronization group

64

LAN Sync Group No 16

capacity

6

New IPCS KX-NS0154

1-1. LAN Synchronization

• LAN sync is done by combination of Multicast from master and Unicast reply from slave.

Multicast

Master

Slave Slave

Unicast Unicast

Master

Slave Slave

Master

Slave Slave

• 1 Master in 1 LAN sync group.• 1 LAN sync group in same

network segment• No Handover between

different LAN sync Group.

LAN sync Group1 LAN sync Group2

192.168.1.XXX 192.168.2.XXX

7

New IPCS KX-NS0154

1-1. LAN Synchronization

• L2SW layer should be bellow 7 layers to keep good condition to minimize packet delay .

• Recommended to use Giga SW.• Recommended to use SW tested by

PSN. Refer other PPT describe detail about NS0154.

Master

Slave

Slave

SW 1

SW 7

SW 8

Slave

OK

OK

NG

SW 2SW 3

SW 4

• Use NS0154 at isolated network by using method like VLAN.

8

New IPCS KX-NS0154

1-2. Easy Installation

• Each slave sync with master directly via LAN cable.

• Out of sync at single CS not affect other CS.

• Each CS can locate based on PS coverage. Each CS not necessary to overlap each other.

NS0154 has easy to install philosophy same like Legacy CS based onLAN synchronization. NS0154 can be registered to NS1000 automatically under DHCP environment by default.

Can be allocated same as Legacy CS

9

New IPCS KX-NS0154

1-3. Survey tool

LAN environment survey tool prepared to use as network assessmenttool.

• Survey can be continued also during normal operation period.

• The tool can be accessed through Off-line maintenance console.

10

New IPCS KX-NS0154

1-4. OtherItem Description NS0154 NCP0158

LLDPLLDP can be enabled or disabled by local programming ( through off line Web-MC)

Yes No

Port punching for media relay gateway

Send dummy packet to prevent rooter port closing for media relay gateway.

Yes No

Announce Modefor remote installation

If ANNOUNCE mode is enabled, NS0154 can provide the PBX’s IP Address information to other terminals in the remote location in place of manually programming the PBX’s IP address at each terminal (support same feature NT5xx have)

Yes No

PS firmware update over the Air

Firmware of TCA185/285/385 can be updated through NS0154 Yes No

PS version display in Web-MC

Version of TCA185/285/385 can be shown in Web-MC (PS firmware update is needed to use this feature) Yes No

Redundancy NS0154 can change the connection to secondary PBX in case of primary PBX failure Yes No

DECT Encryption Encryption between PS and IP-CS is available.*When current repeater (KX-A405), encryption cannot be used.(New repeater which supports Encryption is planned)

Yes No

Wide band audio

KX-NS0154 supports wide band audio.As a condition about this feature, wideband audio for all CSs in the synchronization group is unavailable if Legacy CS or NCP0158 exist in each group.

(Future  Study)

No

11

2. Small Call Center

12

Small Call Center Feature Enhancement

2-1. Call Pickup Group Monitor

While incoming a call onto members of the pickup group, it is possible to notify the call for other members by display of the extension number/name and sending short ring tone on the phones.

13

Small Call Center Feature Enhancement

2-1. Call Pickup Group Monitor

Conditions• All EXT is scanned periodically

• The call ring at other EXT can be presented at LCD every 15Sec.

• The call information display period can be choose from 5/10/15Sec.

• Short tone can be set together with call display.

• Maximum 256 EXT can have this ring at other EXT monitor feature.

• Only DPT and IP-PT which has 3 line or 6 line display support this feature. (UT series not supported)

• During auto redial standby, LCD control by CTI “SetDisplay” command and during paged, monitor information can’t be displayed.

14

Small Call Center Feature Enhancement

2-1-2. Queue position announcement enhancement

• The prompt for 1st person in the queue has been changed as bellow.  “ One other person is waiting to connect.”/ OLD-V3   →  “ You are 1st in the queue.”/ NEW-V4 onward

There is System option bit to change the prompt to old one.

Ext 200

Deliver Call

Ext 201

Ext 202

ICD-Group #601

Incoming Calls

1st caller in queue

Queuing announcementYou are 1st in the queue.

Necessary to install new prompt file.

15

3. Remote Worker

16

Remote Worker Feature Enhancement

3-1. EXT Busy Status

• In addition of busy status indication at DSS with this feature, the status of forwarding extension itself can be changed as busy. • When other extension calls to the forwarding extension with talking

at forward destination then the caller gets busy tone.

This can be programmed by System basis program.

17

4. Boss Secretary

18

Boss Secretary Feature Enhancement

4-1. Remote Call Forward On/Off• User can control forward setting on a specified extension by Group FWD

button. Group FWD button now accept EXT Number. • This Group FWD button show FWD status of the specific extension as well.• In this example, a secretary can set FWD on/off at boss’s phone.

• Ability of control FWD setting at Boss’s EXT by Secretary must be assigned for Boss extension by extension basis programming and Secretary extension must assign the COS setting Enabled this operation.

• FWD destination must be set by boss, system administrator or installer.

19

5. Web-MC

20

Web MC Enhancement

5-1. Dsys Converter for Slave Unit

Key items in original TDE/NCP database can be converted and marge into Dcsys of master as a part of system data for slave unit in One-look networking.

TDA/TDE/NCPTDA/TDE/NCP

NS1000 NS1000

Legacy GW1

Master SlaveOne Look Networking

Legacy GW1

TDA/TDE/NCP TDA/TDE/NCP

QSIG Networking

Data Base conversion to SlaveKey items only

Data Base conversion to MasterAll PBX related data

21

Web MC Enhancement

5-1. Dsys Converter for Slave Unit

  Before Ver.4.1 Ver.4.1 or later

Supported units(Convert to)

Master unit Master unit and Slave units

• Card assignment, extension settings and trunk setting can be converted and merged into DCSYS for Master unit.

• System-wise setting such as numbering plan, COS and so on, are not able to be converted.

• Group setting that includes ICD group paging group is not available to generate.

• Numbering plan, must be manually pre-programmed(adjust) at Master unit if they need to be modified.

22

Web MC Enhancement

5-1. Dsys Converter for Slave Unit

<General operation flow>1)Numbering Plan and other system based settings should be programmed at Master unit before adding TDE/NCP database file as slave data.

2)Add and set up slaves at Master.

3)Take DCSYS file out from Master unit and save it on PC which has Off-line programming tool.

4)Activate “Database Converter” from the launcher of off-line programming tool.

5)Select the DCSYS file from Master and system data file from TDE/NCP(slave site).

5)Execute database converting, then the tool will create new DCSYS file include the converted data for slave site.

23

Web MC Enhancement

5-2. Dsys Converter for UM

• Following TVM setting data can be converted into UM data of NS1000 by converter on NS1000 Off-Line tool.

Mailbox setting Custom service  • Only setting with the mailbox number which are matched with

assigned mailboxes of NS1000 can be converted as UM data. • TVM database of version 3 can be converted.

DxSYS file

Back up Import

Transfer

24

Web MC Enhancement

5-2. Dsys Converter for UM

<Operation flow>1)Backup system data from TVM

2)Create mailboxes, which have same mailbox numbers in the TVM, in NS1000 and transfer DCSYS file from NS1000 to PC

3)Initiate convert tool from launcher in off-line of programming.

4)Specify the both data file on the tool

5)Start converting on the tool

6)Restore DCSYS file into NS1000 after converting

25

Web MC Enhancement

5-3. EXT list order

V3 or BeforeVer.4

Improve Extension list at Add-userIn Ver.3 or before, it is hard to find desired extension number from extension list on Add-user menu since the numbers are listed without order. From ver.4, the list shows the numbers with young number order for ease of finding.

26

6. Other

27

Other

6-1. IP Address Redundancy for SIP Trunk

If SIP carrier has IP address Redundancy service.Secondary IP address can be assigned for the service on SIP trunk setting.

28

Other

6-2. Call Waiting Tone for EHS Headset

Current version New version

Sent from speakerSent through headset

orSent from speaker

The tone is sent from handset receiver from version Ver4.0. It depends on terminal basis program setting.Following models of phone are available for it. (Default: Sent from speaker)

KX-DT546, KX-DT543KX-NT556, KX-NT553

Other models from above phones can send the tone only from speaker on it.

29

6-3. SLT pre-ringing

V4.0 supports pre-ringing function with receiving Caller-ID signal for SLT on legacy gateway.The SLT pre-ringing is selectable for card basis. (Default: Enable)Following cards can support pre-ringing.

- MCSLC24 / MCSLC16- ECSLC24- EMSLC16 Note: The firmware upgrade of the cards is required for this feature. Optional SLC2 cards of NS1000 are not available for this feature.

Other

30

How to Program?

31

Appendix

New IPCS KX-NS0154

NS0154 can be registered to NS1000 automatically by default.NS0154 side DHCP enabled by default so if there is DHCP server, IP address allocate automatically.There is separate “Registration Mode” setting besides IP Terminal.

32

Appendix

New IPCS KX-NS0154

Number of channel at NS0154 can be expandable from 4 ch to 8ch.It can be done by AK(KX-NSE2XX: XX=01, 05, 10, 20/ XX= number of CS)

33

Appendix

New IPCS KX-NS0154

LAN Sync Group need to be defined for each CS.

34

Appendix

New IPCS KX-NS0154

Secondary Setting can be assigned for NS0154.

35

New IPCS KX-NS0154

“CS Repeater Mode” is selectable.

36

Appendix

New IPCS KX-NS0154

Bellow setting can be defined for each LAN sync group:1)Synchronization packet type/IP address2)Long term Diag timer

Not necessary to change level until trouble may present.

37

New IPCS KX-NS0154

Firmware update from NS1000 can be done for NS0154/TCAX85.

38

Small Call Center Feature Enhancement

Call Pickup Group Monitor Information display duration can be set.

39

Small Call Center Feature Enhancement

Call Pickup Group Monitor feature need to be defined by each Group.

40

Small Call Center Feature Enhancement

Call Pickup Group Monitor notification mode can be defined at each EXT.

41

Remote Worker Feature Enhancement

DSS shows busy while talking at Mobile that paired with EXT by FWD NA.

42

Remote Worker Feature Enhancement

V-PS can be set as “Busy on busy” target or not.

43

Boss Secretary Feature Enhancement

Assign at Boss EXT. EXT has which COS can control Boss EXT FWD remotely. Ex. Boss EXT “Remote FWD COS” = COS3 Secretary EXT has COS3 can control Boss EXT forward remotely.

44

Web MC Enhancement

Dsys Converter for Slave Unit

1)

2)

3)

4)

1) Select “Slave Database Converter”2) Select “TDE/NCP” Dsys file(Must be V8)3) Select “NS” Dcsys that need to add

Slave4) Push “Select”

45

Web MC Enhancement

Dsys Converter for Slave Unit

Select target “Slave”

46

Web MC Enhancement

Dsys Converter for Slave Unit

Confirm convert style

47

Web MC Enhancement

Dsys Converter for Slave Unit

You can select whether convert or not for these 3 items.

48

Web MC Enhancement

Dsys Converter for Slave Unit

Set name and time zone for this “Slave”

49

Web MC Enhancement

Dsys Converter for Slave Unit

Set WAN setting for this “Slave”

50

Web MC Enhancement

Dsys Converter for Slave Unit

Set IPPT reg mode for this “Slave”

51

Web MC Enhancement

Dsys Converter for Slave Unit

Set SNTP setting for this “Slave”

52

Web MC Enhancement

Dsys Converter for Slave Unit

Set Maintenance setting for this “Slave”

53

Web MC Enhancement

Dsys Converter for Slave Unit

Start convert and add “Slave”

54

Web MC Enhancement

Dsys Converter for Slave Unit

Show conversion result

55

Web MC Enhancement

Dsys Converter for Slave Unit

You can save new Dcsys that include converted “Slave”

56

Web MC Enhancement

Dsys Converter for Slave Unit

While you open the Dcsys you could see “Slave” that you convert and add.

57

Other

IP Address Redundancy for SIP Trunk

58

SLT pre-ringing

Other

59

Appendix

60

END

61

20140425-00  ★ NS1000 V4.0 PBX Product Summary_Rev0.2_25Apr2014.pptx - draft release

20140606-01  ★ NS1000 V4.0 PBX Product Summary_Rev1.0_6June2014.pptx - 1st release

Modification

top related