© boardworks ltd 20051 of 25 these icons indicate that teacher’s notes or useful web addresses...
Post on 11-Jan-2016
213 Views
Preview:
TRANSCRIPT
© Boardworks Ltd 20051 of 25
These icons indicate that teacher’s notes or useful web addresses are available in the Notes Page.
This icon indicates that the slide contains activities created in Flash. These activities are not editable.
For more detailed instructions, see the Getting Started presentation.
© Boardworks Ltd 20051 of 25
Graphic ProductsDrawing
© Boardworks Ltd 20052 of 25
Learning objectivesL
earn
ing
ob
ject
ives
© Boardworks Ltd 20052 of 25
To learn how to present designs using the following drawing techniques:
sketching
crating
perspective drawings
isometric drawings
working drawings (orthographic projections).
To learn how to enhance drawings using the following techniques:
3-tone rendering
thick and thin lines
hatching and textured effects.
© Boardworks Ltd 20053 of 25
Freehand sketching allows you to convey ideas very quickly. You should use sketching when drawing initial ideas or developing chosen designs.
Sketching is carried out without the use of drawing equipment such as rulers or rubbers.
The basic shape is drawn very lightly with
a pencil to allow for repeated corrections.
The shape is developed further
and begins to become more visible.
A bolder outline is drawn by applying greater
pressure. This draws the eye to the image.
Sketching
© Boardworks Ltd 20054 of 25
Crating
© Boardworks Ltd 20055 of 25
Drawing in 3D can be difficult to begin with.
There is a range of grid papers available to help you. The grid paper can be put under your working sheet to guide you.
The different styles of grid are designed to help you draw different types of drawing:
Squared grid Isometric grid
Grids and underlays
© Boardworks Ltd 20056 of 25
Perspective drawings give a sense of depth. There are two types: one point perspective
two point perspective.
A vanishing point This is positioned on the horizon line. The drawing is ‘pulled into’ the vanishing point.
A horizon line This is at eye level. It is the line at which the ground meets the sky.
Both types have similar characteristics and involve the following:
Perspective drawings
© Boardworks Ltd 20057 of 25
One point perspective drawings
© Boardworks Ltd 20058 of 25
One point perspective drawings
© Boardworks Ltd 20059 of 25
Two point perspective drawings
© Boardworks Ltd 200510 of 25
There are two different styles of three dimensional drawing – oblique and isometric.
At GCSE you must become competent in isometric drawing.
This is how you draw an oblique projection:
You begin with a 2D
shape.
Then draw the same shape
again, offset from the original shape.
Connect the images together.
Oblique drawings are not the best way to present your ideas. They only show one side of the shape in any real detail.
Rub out the lines that cross
the image.
Isometric drawing
© Boardworks Ltd 200511 of 25
Then work away from the line,
drawing lines up at 30 degrees.
Connect the top two edges by working at 30
degrees again. They should meet exactly.
This drawing shows the shape in more detail
than the oblique projection.
This is how you draw an isometric projection:
Put the two side lines in, making sure
they are vertical.
Isometric drawing
Begin by drawing the centre edge of your
shape. Draw it vertically up the page.
© Boardworks Ltd 200512 of 25
Any shape can be drawn as an isometric projection. For complicated shapes, remember to use crating (mentioned earlier in this presentation) to ensure that your shapes have the correct proportions.
The ‘crate’ is drawn isometrically.
Isometric drawing
© Boardworks Ltd 200513 of 25
Working drawings are informational drawings – they give full details of an object’s size in 3D, and how its various parts are arranged.
All working drawings are done to scale so that they give an accurate representation.
Working drawings
Continuous thick line – outside edges
Dashed line – hidden detail
Chain line – centre lines
Continuous thin line – inside lines and dimension lines
Different lines are used for different parts of the drawing:
© Boardworks Ltd 200514 of 25
Orthographic projections give three views in one drawing. The views they show you are:
The views must be drawn perfectly in line with each other.
plan view
front view
side view.
Orthographic drawings
They have to follow British Standards in a number of ways.
Most working drawings are third angle orthographic projections.
They bear this symbol.
© Boardworks Ltd 200515 of 25
Orthographic projections must be drawn to British Standard requirements, as shown above.
Orthographic drawings
© Boardworks Ltd 200516 of 25
Orthographic projections can be done by hand or on the computer.
Here is an example of a third angle orthographic projection done using ProDesktop.
Orthographic drawings
© Boardworks Ltd 200517 of 25
3-tone rendering is a shading technique using three varying tones of colour. The tone depends on the amount of light hitting each part of the object.
The lightest tone is used where the light strikes the object most directly.
A medium tone is used for areas that get some light.
The darkest tone is used for areas that get very little light.
The position of the light source dictates which surface carries each tone.
3-tone rendering
© Boardworks Ltd 200518 of 25
3-tone rendering
© Boardworks Ltd 200519 of 25
You can enhance the images you draw to give them a more impressive and realistic finish.
The final outcome can vary greatly depending on the media used to render it. These are some possibilities.
Enhancement
© Boardworks Ltd 200520 of 25
You can create a more realistic 3D image by applying thick and thin lines to it.
A thick line is applied where you can only see one of the two connecting surfaces that make up the line.
A thin line is applied where both connecting surfaces that make up the line are visible.
Enhancement – thick and thin lines
© Boardworks Ltd 200521 of 25
Hatching is another way of rendering. It has three main uses:
Hatching is added with a pencil – a softer pencil is better if you want to vary the tone. You can also vary the density of the hatching.
to highlight key areas or hidden areas
to add a more three dimensional feel
to represent wastage.
Wastage (material to be removed)
Hidden area
Enhancement – hatching
© Boardworks Ltd 200522 of 25
Texture can be applied to objects to give the illusion of a surface finish. This can be used in presentation work to represent the materials the object will be manufactured from.
Texture can be added with a variety of mediums and using different styles and techniques.
Study the following textures and see if you can recreate them.
One of the easiest textures to apply using different shades of brown, orange and yellow. The grain effect is very easy to draw once the object has been shaded.
Wood
Enhancement – texture
© Boardworks Ltd 200523 of 25
MetalWhen applying a metal texture, remember your three tone shading. Build up the colour using grey and pale blue, then add reflective streaks as if the light is bouncing off the surface. You can do this using a white pencil or by rubbing out streaks of the base colour.
Plastic
Plastic is one of the more difficult textures to apply as it can be a very reflective surface. Use a technique similar to that of metal. Make sure the reflection lines follow the shape of the object.
Enhancement – texture
© Boardworks Ltd 200524 of 25
Concrete
The easiest way to apply this texture is with a series of dots. Place the dots closer together to create dark areas and further apart to produce lighter areas. Try to make the surface look uneven.
Fabric
You need to create a soft effect, so avoid using straight lines drawn with a ruler. Soften the edges and apply bold colours using strokes in different directions to give a woven texture. You can also use lots of short pencil streaks to produce a furry effect.
Enhancement – texture
© Boardworks Ltd 200525 of 25
Key pointsK
ey p
oin
ts
© Boardworks Ltd 200525 of 25
Rough images can be created quickly using sketching and crating.
3D objects can be drawn as one or two point perspective drawings, or as isometric drawings.
Designs can be presented formally as working drawings (orthographic projections).
Drawings can be enhanced using 3-tone rendering, thick and thin lines and textured effects.
top related