© 2006 bei technologies 1-800-encoder, installing the ln linear encoder note: the following...
Post on 14-Dec-2015
232 Views
Preview:
TRANSCRIPT
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Installing the LN Linear Encoder
Note: The following installation example is for demonstration purposes only and may not reflect your exact installation requirements.
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Correct Read head alignment
• Read head must be parallel to the axis of travel to within ± 0.002”
Readhead(Front)
Top
Axis of travel
Axis of travel
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Incorrect Read head alignment
• Damage to scale and / or read head imminent!
Readhead(Front)
Top
Axis of travel
Axis of travel
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Traverse system to extreme limit opposite cable exit
Front view
Top view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Gently run scale through read head
Front view
Top view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Slide scale support clamp onto scale end
Front view
Top view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Transfer punch through link
Front view
End view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Install support pillar, then loosely attach scale bracket
Front view
End view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Gently slide scale through read head and left support
Front view
End view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
While sliding scale back and forth, tighten support in place on pillar
Front view
End view
Tighten clamp screw
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Remove scale, traverse system to extreme limit toward cable exit
Front view
Top view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Front view
Top view
Gently run scale through read head
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Front view
Top view
Slide scale support clamp onto scale end
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Transfer punch through link
Front view
End view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Drill and tap at punch mark
Front view
End view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Install support pillar, then loosely attach scale bracket
Front view
End view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Slide scale through read head and support
Front view
End view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
While sliding scale back and forth, tighten support in place on pillar
Front view
End view
Tighten clamp screw
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Gently run scale through support, read head and opposite support
Front view
Top view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Tighten scale clamp at left end
Front view
Top view
© 2006 BEI Technologies
1-800-ENCODER, www.beiied.com
Snug up scale clamp at right end
Front view
Top view
top related