allura - lowes holidaypdf.lowes.com/installationguides/671256387643_install.pdfallura® model...
TRANSCRIPT
Non-Removable Removable Stopper Stopper
Quick Install Guide Allura Widespread Lavatory Faucet, SLW-4712
Step 1
Attach control valves to sink
Step 1
Attach center spout to sink
Step 2
Attach pivot rod to drain body
Step 6
Connect lift rod, clevis strap,pivot rod and adjust linkage
Step 7
Install stopper andset eye position
Step 5
Flush water supply lines
Step 9
Attach drain body to drain trap
Step 8
Step 3
SConnect water supply lines
Fasten drain body andtail piece to sink
Step 4
Tools & Materials Need Help?Contact Symmons customer service at(800) 796-6667, (781) 848-2250Email: [email protected] - Friday 7:30 am - 7:00 pm EST
Please check Symmons website for technical help, the latest product information and warranty policy.www.symmons.com/service
Widespread Lavatory Faucet SLW-4712
Installation and Service Instructions
Allura®
Model NumbersSLW-4712 Lavatory faucet with
pop-up drain
Note: Instructions replace document ZV-782 as of June 2012.
Alternate Finish Codeappend to part numbers when applicable
-STN Satin Nickel
-- Chrome (standard)
Compliance
- ASME A112.18.1/CSA B125.1- NSF/ANSI 61.9, NSF/ANSI 372- WaterSense 1.0 & 1.5 gpm
Certi�ed byNSF International
PlumbersPutty
Pipe
Sealant5/64"
Step 3 Connect water supply lines
■ Thread tee onto end of spout.Note: This may require 4 inches of clearance.
■ Apply pipe sealant on both flex hose adapters. Thread into side of tee.
■ Attach flex hoses to flex hose adapters.
■ Plumb hot water supply to left valve body inlet, cold water to right inlet (1/2 inch supply hoses not included).
■ Check for leaks if only replacing faucet and drain is already installed by first turning faucet handles to the OFF position and then turn water supply valves ON.
Step 4 Fasten drain body to sink
■ Remove stopper, unscrew flange and remove flat rubber washer from end of drain body as shipped.
■ Apply plumber’s putty around bottom of flange.
■ Move friction washer, beveled washer and flange nut down away from end of drain body.
■ Place flange into drain opening and from under sink screw drain body into flange at least 2-3 turns until hand tight. Apply putty or teflon tape to tail piece and attach to drain body.
■ Position drain body so pivot cavity is facing rear of sink and then slide beveled washer and friction washer up against sink.
■ Tighten flange nut up against friction washer to evenly compress beveled washer while also ensuring flange is centered in drain opening. Take care not to over tighten flange nut.
Caution: If replacing an older faucet ensure water supply is turned OFF before removing. Then turn both faucet handles to the ON position to relieve water pressure.
Step 1 Attach control valves to sink
■ Thread flange nut down about 2 inches from threaded end of valve body.
■ Insert valve body from underneath sink up through mounting hole.
Ensure valve with red striped hose (hot) is on the left and blue (cold) is on the right.
■ Place gasket over valve body and thread fastener onto valve body until fastener is secured tightly to valve body.
■ Ensure spindle is rotated to the OFF position.Fasten handle to top of spindle located in OFF position as shown in illustration.
■ Press plug button into top of handle.
■ Tighten flange nut and mounting washer under sink and secure with mounting screws if necessary.
Step 2 Attach center spout to sink
■ Unscrew tee and remove washer and nut from threaded end of spout as typically shipped.
■ Insert through mounting hole in sink and then fasten from under sink with washer and nut.
■ Tighten nut while ensuring spout is centered over mounting hole and flat edge of washer is facing rear of sink.
Installation Instructions
fastener
gasket
valve body
mounting washer
�ange nut
mounting screws
hot = cwcold = ccw
spindle OFF
plug button
screw
handle
spout
washer
nut
tee
Pipe
Sealan
t
�ex hose
spout
valveoutlet
& inlet
�ex hoseadapter
tee
valve body
PLUMBERSPUTTY
�ange
beveledwasher
frictionwasher
pivotcavity
�ange nut
drain body
tail piece
Installation Instructions
Page 2
Step 5 Install stopper and set eye positionStopper can be removable or non-removable determined by position of eye hole when inserting pivot rod.
■ Insert stopperthrough flange opening and rotate to position eye hole.
Removable stopper When installed in removable position, move pivot rod to the up position (lift rod is in the down position when later installed). Eye hole will slide over end of pivot rod.
Step 6 Attach pivot rod to drain body
■ Remove retaining nut and outer seat from pivot cavity.
■ Insert pivot rod into pivot cavity so pivot ball is against inner seat and rod passes under end of stopper according to selected eye hole position.
■ Insert outer seat over pivot rod with curved end against pivot ball.
■ Fasten pivot rod to drain body with retaining nut and tighten using your fingers until ball is seated snug and pivot rod can move around freely.
Step 7 Connect lift rod and adjust linkage
■ Insert lift rod through hole on top of water spout.
■ Fasten end of pivot rod with spring clip through location hole in clevis strap that is best aligned to enable lift rod also fasten to end of clevis strap when in the up position and stopper is in the closed position.
■ Insert lift rod into end of clevis strap and fasten with thumb screw at location where stopper can be easily opened and closed.If necessary, select another location hole in clevis strap and re-adjust lift rod where fastened to clevis strap
Step 8 Flush water supply lines
Thoroughly flush the supply lines to prevent foreign matter, i.e. copper chips, sand, etc. from damaging the sealing surface inside control valves.
■ Remove aerator from end of faucet water outlet by rotating counter clockwise.
■ Turn hot and cold faucet handles to full ON position, open water supply valves and run long enough to flush supply lines thoroughly.
■ Turn faucet OFF, replace aerator, and check for any water leaks.
Care of faucet finishClean finish area by using mild soap and water or non-abrasive cleaner and then rinse immediately. A non-abrasive wax may be used to preserve finish area.
Valve cartridge replacement
Remove faucet handle
■ Pry loose and remove plug button using your finger.
■ Remove Phillips head screw in center of handle.
■ Lift off handle from cartridge spindle.
Remove cartridge
Using a wrench, turn hex nut on cartridge counter clockwise. Note: Ensure valve assembly doesn’t rotate under sink while turning nut.
Insert new cartridge
Insert replacement cartridge into center of valve and tighten hex nut using a wrench.
Attach handle
■ Ensure cartridge spindle is rotated to the OFF position.
■ Attach handle located in the OFF position as shown in illustration.
■ Insert screw into center of handle and replace plug button.
stopper�ange
nonremovable removable
pivot rodretaining nutouter seatpivot ballinner seatpivot cavity
thumbscrew
locationholes
springclip
pivot rod
clevis strap
lift rod
removeaerator
hot = cwcold = ccw
spindle OFF
cartridge
valve
plug button
screw
handle
handles set in the OFF position
Page 3
RL-072*plug buttons
screw
handle
KN-114 (hot)OFF = CW
KN-113 (cold)OFF = CCW
valve cartridge
KN-113identifiedby groove
Handle kit
Part Number ItemReplacement Parts
LN-15*FLR-110-1.5*FLR-110-1.0*
aerator �ow rates2.2 gpm (8.3L/min)1.5 gpm (5.7L/min)1.0 gpm (3.8L/min)
lift rodP-108CL12*
standard aerator2.2 gpm
faucet handlereference table
valve cartridgereference table
stopperP-100N
pop-up drainassembly
RL-154LR*includes lift rod
and stopper
Ordering replacement parts:Call Symmons customer service at (800) 796-6667,(781) 848-2250, M-F 7:30 am - 7:00 pm EST orcheck our website at www.symmons.com for alist of Symmons distributors.
Parts Assembly Allura Widespread Lavatory Faucet, SLW-4712
(red stripe on hot hose)
(blue stripe on cold hose)
aerator
* Note: When ordering replacements parts for faucets with an optional decorative �nish, append appropriate three letter �nish suf�x code to part numbers marked with an asterisk (*).
4-1/2"(114 mm)
6-5/16"(160 mm)
5/8" dia (16 mm)Hole size
1-1/8" (29 mm) min1-1/2" (38 mm) max
5/8" (16 mm)
3-1/4"(83 mm) 1-5/8" (42 mm)
2-1/2"(64 mm)
3-1/8" (79 mm)
1" dia. (25 mm) Hole size
1-1/16" (27 mm) min1-7/16" (37 mm) max
4" (102 mm)
Flexible hose
Deck thickness 1-3/8" (35 mm) max.
Dimensions Allura Widespread Lavatory Faucet, SLW-4712
2-1/4" dia(58 mm)
2-5/16" dia(59 mm)
1/2"-14 NPSM
8" (203 mm)
Note: Dimensions subject to change without notice.
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621 Copyright © 2018 Symmons Industries, Inc. ■ symmons.com ■ [email protected] ■ ZV-1084 REV F ■ 071318
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.