allbe1 user manual - storage.googleapis.com...by pressing the lock feature icon, the app will ask...

www.allbe1.com of 25

AllBe1 User manual

Table of Contents

1. Introduction ........................................................................................................................ 3

2. CAUTIONS ........................................................................................................................... 3

3. Using the AllBe1 Application .............................................................................................. 4

4. General Settings: ................................................................................................................ 7

5. Movement detection .......................................................................................................... 8

6. Human detection ................................................................................................................ 9

7. UV ..................................................................................................................................... 12

8. Temperature ..................................................................................................................... 13

9. Multi button ..................................................................................................................... 14

10. Out of range ..................................................................................................................... 16

11. Tracker .............................................................................................................................. 17

12. Kid in the car ..................................................................................................................... 18

13. Lock screen feature .......................................................................................................... 19

14. Events logging ................................................................................................................... 20


15. Troubleshooting ............................................................................................................... 21

15.1 CONNECTION PROBLEMS ................................................................................................................... 21 15.2 SHUTTING DOWN THE ALLBE1 DEVICE ............................................................................................. 21 15.3 THE ALLBE1 NOT TURNING ON ........................................................................................................ 21 16. Package Contents ............................................................................................................. 21

17. Specification ..................................................................................................................... 22

18. Compliances: .................................................................................................................... 23

19. Warning and Disclaimer ................................................................................................... 24


1. Introduction The AllBe 1 is a multi-sensor device with Bluetooth Low Energy (BLE) extended range where the

user can select multiple features via the smartphone App.

The AllBe1 has the following features:

Human detection by passive infra-red detector

Movement detection by 3D accelerometer

Over & under UV exposer monitor by UV sensor

Temperature sensing and monitoring

Out of range detection & alarm

Tracker to help you find your assets

Help message, "Selfie" picture, audio recording and more with multi-function button

2. CAUTIONS

Use only certified USB charger with Micro USB connector.

Device should be charged only when away from human body.

Device should not come in contact with water and other liquids.

If the AllBe1 Lock function is used, please make sure to keep a written

backup password in case you forget the PW. The smartphone will lock

without an unlock option (no PW restore).


3. Using the AllBe1 Application

Before using the app, please charge the AllBe1 for 2 hours. Please use power supply with

current limit of maximum 200ma.

Step 1 – Install the AllBe1 App. – go to "Google Play" or to "Apple Store", search for Allbe1 and

download the App. (please agree to the "Using terms and warning")

Step 2 –Open the App., you get a WELCOME! screen with Black button and the Bluetooth icon.

The app will ask your permission to turn ON the BT. Please permit.

Step 3 – Turn on the AllBe1 by short pressing the AllBe1 button. The Blue LED should flash – this

is the signal that the AllBe1 is trying to pair with your smartphone.

Step 4 – Click on the Black BT icon on the screen and you will see the AllBe1 name and

"Connect" button.

Click on "Connect" and the App. will connect to the AllBe1 and the Blue LED will begin flashing

slower, with less intensity.

Note: On some Android versions the BT (BLE) is connected to the GPS, so in case you can't see

Allbe1 name on the WELCOME screen, try to turn ON the phone's GPS.

Now you should see the following screen:


You can repeat steps 3 and 4 with additional AllBe1 devices and all of them will appear on the

screen.

After clicking on the AllBe1 device that you want to connect to, you will see the following screen:


Features selecting grid screen

Choose the feature you would like to open. A long click will operate it immediately, a short one

will open it and then you have to move the ON switch on the top right side.

Note: Pressing the AllBe1 operating button for 8 seconds will shut it down.

Note: After the AllBe1 device is disconnected from the phone it will still work in waiting mode.


4. General Settings: 4.1 By pressing the setting icon (tooth wheel) on the top right of the screen, you can set some

general options like choosing the alarm ringtone (only in Android OS), choose to secureing the

AllBe1 connection with a password, automatically connect after disconnect, giving the AllBe1 a

specific name, choosing the temperature units, and review some general information about the

AllBe1.

4.2 On the WELCOME screen on the top right side you can chose the working language and see

the App. version.

4.3 On top left side in each App. you can go back clicking on the small ‘back’ arrow

4.4 Some functions contain a re-notify option allowing you to select a repetitive period for the

alarm as long as the AllBe1 detects a "valid case" to cause the alarm.

General settings screen.


5. Movement detection You can use the Allbe1 to alert you, when someone is moving your belongings

You can put it in your car, on your bike, in your bag, a drawer or any other place you like in order

detect once someone moved your asses.

You can also adjust the movement sensitivity:


6. Human detection The Passive Infra-Red (PIR) sensor senses the Infra-Red radiation that is emitted by human

presence.

The PIR sensor is covered by "Fresnel lens" in order to collect the IR radiation and improve the

detection performance.

PIR sensor Fresnel lens detection pattern

In order to achieve the best performance with the PIR sensor, the AllBe1 should be mounted

with the PIR sensor special bracket, see picture bellow:


AllBe1 PIR sensor special bracket for human detection usage

The user can select the sensitivity level or use a custom threshold for alarm:


Custom value setting:


PIR sensor threshold setting

Place the AllBe1 to "look" at the area you want to detect when no person is present.

Operate the function to ON. You will see "Initializing" massage for about 20 seconds.

Once initialized, you see a display showing the Infra-Red signal level detected. This is the

"background radiation" level.

Select one of the Low, Medium or High sensor sensitivity settings. Walk in front of the AllBe1 at

a distance of 6 feet (2 meters) and verify that you are detected without fallse alarms. After you

are detected, you see the Human detection alert! Signal.

If you don't succeed with one of the above sensitive levels, you can set a customize threshold.

Set a customize threshold:

To select a custom threshold, set the sensor sensitivity to "Custom" and then set the PIR

threshold level to at least 5 degrees above the "background radiation" signal level.

We recommend repeat this test 2 or more times to set the right level.

Notes:

The default PIR level is 25 which is enough to cover about 6-10 feet (2-3 meters) in

front of the AllBe1.

Special notes for using the PIR sensor:

The "Fresnel lens" should be pointed to the desired detection area.,

The AllBe1 with the bracket should be placed on a shelf or similar object 4-6 feet (1.2-

1.8 meters) high.

Do not place the Allbe1 near air conditioner vents, open windows or near any heat source,

as these can cause false alarms

The PIR sensor is for indoor use only.

7. Ultra Violet Sensor Operating this feature of the AllB1 will show the current Ultra Violet (UV) index.

You can set a range for the desired UV threshold; anything beyond this level you will get an

alarm.

Note: the UV sensor on the AllBe1 is located under the LED's transparency window.


UV sensor setting screens

8. Temperature Sensor By operatinge this feature, the AllB1 will show the current temperature.

(0.5C deg. accuracy, measuring the temperature on board, note that during charging it may

become hot and the measurement will not be accurate)

You can set a range of a desired temperature (low and high threshold) by moving the Red

points. Once the temperature passes either threshold, you will get an alarm.

Note – when the AllBe1 is disconnected from the phone this feature, will not continue to work

in the background.


Temperature sensor setting screens

9. Multi-Function Button The AllBe1 has a multi-functional button, a small grey button on the end of the sensor.

When you engage this feature you should also select "Action to perform" when the button is

pushed.


Notes:

The audio recording files will be saved in a folder named AllBe1. You can find the

recordings your phone's Downloads folder.

In IOS phones (iPhone) the recorded file list will be shown on the bottom of this screen.

SMS feature is not avaiable with iPhones.


10. Out of Range

When you choose this feature the AllBe1 will alert you once the AllBe1 device is away from the

phone. You can select long or short range alarm.

Notes:

1. The phone measures the AllBe1's signal strength and notes the distance to the AllBe1.

2. When you select the long rang alarm, it will alarm once the AllBe1 is

disconnected from the phone.


11. Tracker This feature will allow the user to locate belongings, which are connected to the AllBe1, like a

key chain for example.

Once you touch the small RADAR icon near the Allbe1 device name, the tracker screen will show

the signal strength numbers 0-100 and a vocal beeps according to the signal strength.

As you come closer to the AllBe1, the signal strength figure increases and the beeps become

more frequently.

Note: The Allbe1 is always in tracker mode.

Tracker screen Radar icon for Tracker


12. Kid in the car

Using this feature will help you not to forget your kid in the car.

Important: When you carry a kid in the car, put the AllBe1 in the car and operate this feature.

About 15 seconds after you get more than 15-20 feet (3-4 meters) away from the car, you will

receive an alarm notification.

Note – you will get this alarm notification too, if the BT link is disconnected.


13. Lock screen feature

By pressing the LOCK feature Icon, the app will ask you to type password and confirm it again.

This feature will lock the phone screen when the AllBe1 is disconnected from the phone,

Caution: Be careful! With this feature enabled, if you lose or misplace the AllBe1

device and forget the password, you will not be able to open your phone!!!

Note: this feature is not available for IPhone users


14. Events logging

If the Human detection or Movement detection features are operating, the Allbe1 will "stay

awake" all the time (even the BT link is disconnected) and log the events. Once you will connect

again to the AllBe1, the Events icon will be lit. By pressing on the Events icon, you will see the

event and time stamp:

Event logging screen


15. Troubleshooting

15.1 Connection problems

Connection problems may occur due to BT and API issues on the smart phone / iPad. If this

happens, try switching OFF the BT and turning it ON again. If it still doesn't connect, try

shutting down the phone and AllBe1 devices and then turn them ON again.

Try turning ON the phone's GPS (some Android versions require a working GPS in order operate

the BT).

15.2 Shutting down the AllBe1 device

Press the AllBe1 operating button for 8 seconds and it will shut it down.

15.3 The AllBe1 not turning ON

Charge the AllBe1 for more than 5 minutes and try again. After it turns on, continue charging it

for 2 hours.

For any other problems please contact us via our website: www.allbe1.com

16. Package Contents

Basic cover and for use

with Key chain or wire

For belt clip For human detection

stand

AllBe1

http://www.allbe1.com/


17. Specification Sensors

Accelerometer: 3 axis, low G, MEMS accelerometer, Digital sensor.

Passive Infrared Sensor: 4 elements Pyro sensor.

Temperature sensor: +/- 0.4 C deg. accuracy digital sensor.

Ambient light + UV sensor, 1-11 UV index + 6500 lux maximum, digital sensor.

RF Section

RF section base on BLE (Bluetooth Low Energy), 2.4GHz ISM band and supports the 802.15.4

Data rate: 260 kbps maximum

Modulation: GFSK.

Sensitivity: -98dbm.

BLE transmit power: 12.5dbm maximum

Power system

Lithium Polymer battery, UL, IEC62133 certifications, capacity of 100mAh, powered the AllBe1

up to 60 days, changed according using profile.

Charging by a standard Micro USB connector. Include internal charger with 100mA charge

limitation. Safety system: Built-in Multiple Safety Timers protection and current sensing,

temperature, overcurrent and voltage monitor safety system.

Maximum consumption current (in TX mode) 35mA

Operation temperature: Operating range of -4 to 140F (-20 to +60C deg.), charging range of 32

to 113F (0 to 45C deg.).

Environmental operating conditions

Storage temperature: -4 to 140F (-20 to +60C deg.)

Durability: IP52 - Water (rain, washing hand) and dust resistance.

Dimension: 32x42x10 mm

Wight: 15 grams


18. Compliances:

FCC ID: 2AJWE-ALLBE

Canada: IC: 22019-ALLBE, HVIN: AB001

FCC Compliance Statement

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential

installations. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio and television reception.

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such

interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference

by one or more of the following measures:

– Re-orient or re-locate the receiving antenna.

– Increase the distance between the device and the receiver.

– Connect the device to an outlet on a circuit different from the one that supplies power to the receiver.

– Consult the dealer or an experienced radio/TV technician.

WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

This device complies with FCC Rules Part 15: Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en

compromettre le fonctionnement.

A distance of at least 0.2 cm. between the equipment and all persons should be maintained during the operation of the

equipment.


Label:

19. Warning and Disclaimer Please Read Before Use AllBe Solutions Ltd. (“AllBe”) is pleased that you have chosen to purchase and use an AllBe device. Certain limitations and restrictions apply to your use of the AllBe1 device and or the Everywhere Dongle. You and you alone are responsible for any result of your use of the AllBe device and you fully accept such responsibility. Furthermore, your use of the foregoing devices, as well as any other AllBe product or service is governed by these terms and by using such device or service you consent to all of the following: AllBe products and services (including the AllBe app and website) are provided by AllBe on an “as is” basis and AllBe expressly disclaims any and all warranties, express or implied, including without limitation warranties of merchantability and fitness for a particular purpose, with respect to any product or service offered by AllBe. AllBe also expressly disclaims any and all warranties related to battery life. Actual battery life of your AllBe device will vary depending on usage, operating temperature and many other factors. Your exclusive remedy for breach of any express or implied warranty or of any other obligation arising by operation of law or otherwise shall be limited to repair or replacement of your AllBe device, at our sole discretion. In no event shall AllBe be liable for any direct, indirect, incidental, punitive or consequential damages of any kind with respect to any AllBe product or service. Please also note the following warnings concerning your use and maintenance of your AllBe device: 1. The AllBe device, Everywhere Dongle and your mobile phone are technology devices that by nature are not infallible. Always make sure you have supplemental support for your desired use of the AllBe device, Everywhere Dongle and your mobile phone.

2. The AllBe device contains small parts that may cause choking. Keep small parts away from children and pets.

3. Check frequently to make sure the AllBe app is activated on your phone and connected to your AllBe device.


4. Even when used properly and in accordance to its intended purpose, the AllBe device serves only as a supplemental safety support system. The AllBe device is not intended to replace, circumvent, mitigate or represent proper supervision of children or any legal duty of parental or supervisory care as required by applicable law.

5. The AllBe device is not intended for use as a medical monitor and is not approved as such.

6. Check reception regularly. Test signal, battery and volume on your phone and device before use.

7. Operation of your AllBe device may be affected when battery power is low. Check batteries regularly.

8. The wireless signal transfer range may be shortened if there is an obstacle between the AllBe device and your phone.

9. Signal strength may be affected by a variety of factors, including without limitation your geographic surroundings, the weather, other nearby Bluetooth usage, certain features on your mobile phone and mobile service availability. Such factors may disrupt the flow of information and the quality of the warning transmitted by your AllBe device to your mobile phone.

10. Ambient noise may restrict your ability to hear the alarm on your phone. Always make sure that you are able to hear your phone alarm in your location before use. AllBe shall not be liable for any misuse or failure of your AllBe device arising from any of the above. All AllBe products and services, including the device and/or service you are using, are the product of hard work and significant development efforts by AllBe and are its intellectual property. You are required to respect AllBe’s ownership of this intellectual property and you may not infringe upon it in any way. For this reason, you may not copy, distribute, disseminate, publish or reverse engineer any and all features of the AllBe app or any AllBe device. Any complaint or claim you may have concerning your use of the AllBe device shall be governed exclusively by the laws of the State of Israel, without reference to provisions concerning conflict of laws. Any such complaint or claim shall be brought exclusively before the courts in Tel Aviv, Israel.

allbe1 user manual - storage.googleapis.com...by pressing the lock feature icon, the app will ask...

Documents