albany technical data sheets

2

5 ALBANY ACRYLIC EGGSHELL

9 ALBANY ACRYLIC GLOSS

13 ALBANY ACRYLIC PRIMER UNDERCOAT

15 ALBANY ALL PURPOSE PRIMER

19 ALBANY ALUMINIUM WOOD PRIMER

21 ALBANY DURABLE MATT EMULSION

23 ALBANY FUNGICIDAL WASH

25 ALBANY GLOSS

29 ALBANY HIGH OPACITY SUPERCOVER

31 ALBANY METAL PRIMER

33 ALBANY NON DRIP GLOSS

37 ALBANY POLYURETHANE EGGSHELL VARNISH

39 ALBANY POLYURETHANE GLOSS VARNISH

Contents

3

41 ALBANY POLYURETHANE MATT VARNISH

43 ALBANY PRIMER SEALER

45 ALBANY RED OXIDE PRIMER

47 ALBANY SMOOTH DURABLE EGGSHELL

49 ALBANY SMOOTH MASONRY PAINT

51 ALBANY SOFT SHEEN EMULSION

53 ALBANY STABILISING SOLUTION

55 ALBANY UNDERCOAT

59 ALBANY VINYL MATT EMULSION

61 ALBANY VINYL SILK EMULSION

63 ALBANY WOOD PRIMER

65 ALBANY YACHT VARNISH

Contents

5

ALBANY ACRYLIC EGGSHELLAn attractive mid sheen waterborne formulation for interior use. Durable and washable.

AVAILABILITY

Colour Range See Albany Literature.

Packaging 1, 2.5 and 5 litre.

PROPERTIES

Drying Time Under normal drying conditions touch dry 1-2 hours and recoatable after 6 hours. Allow for adequate ventilation during the drying period.

Finish Mid sheen.

Composition Pigment: Titanium Dioxide, coloured pigments and extenders Binder: Acrylic polymer Solvent: Water

Spreading Rate Up to 15m² per litre on smooth surfaces.

Wet Film Thickness 66 micrometres at 15m² per litre.

Dry Film Thickness 24.42 micrometres at 15m² per litre.

Volume Solids 36% White. Other colours will vary.

Flash Point Not applicable.

VOC Content EU limit value for this product (cat.A/b): 150 g/l (2007) / 130 g/l (2010) This product contains max. 46 g/l VOC.

Limitations For interior use only. Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION

New Surfaces

Walls All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster or dense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Acrylic Primer Undercoat thinned with up to 10% clean water.

Timber All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper. Remove all dust. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Prime with one coat of Albany Acrylic Primer Undercoat.

Technical Data Sheet

6

All Metals IncludingGalvanised Surfaces must be clean and free from anything that will interfere with the materials to

be applied. Wash with hot water and liquid detergent solution to remove oil, grease orany other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. Galvanised surfaces should be pre-treated with a suitable mordant solution. Overall blackening of the surface will confirm satisfactory surface preparation.

Additional SurfacePreparation - All Metals

Non-ferrous Metals Lightly abrade to a bright (not polished) surface - excluding galvanised surfaces. Rinse thoroughly with clean water to remove all resides. Allow to dry. Prime with one coat of Albany All Purpose Primer.

Ferrous Metals Remove all millscale and rust back to clean metal. Remove all residues. Prime within theworking day with one coat of Albany All Purpose Primer.

PreviouslyDecorated Surfaces

Walls All surfaces must be sound, clean, suitably dry and free from anything that willinterfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with a Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitableproprietary filler. Patch prime bare and filled areas with Albany Acrylic PrimerUndercoat. If after cleaning any areas are still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Primer Sealer.

Timber All surfaces must be suitably dry, and free from anything that will interfere with theadhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Remove grey and denatured surfaces by rubbing down with abrasive paper. Feather edges of sound paint.

Remove all dust. Organic growth must be removed and the areas treated with AlbanyFungicidal Wash. Treat knots with two thin coats of fresh knotting. Fill any fixing holes,open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot prime bare and filledareas with one coat of Albany Acrylic Primer Undercoat.

Metals All surfaces must be suitably dry, and free from anything that will interfere with theadhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime ferrous and non-ferrous metals including galvanised metal with one coat of Albany All Purpose Primer.

Walls, Timberand Metals Wash remaining sound paint with hot water and liquid detergent solution to

remove any contaminants, frequently changing the water. Any glossy or eggshellsurfaces must be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward patch primed and or spot primed areas withAlbany Acrylic Eggshell.


7


COATING SYSTEM Apply one or two coats as required.

APPLICATION Stir well before use. For walls apply using a good quality fine filament synthetic brush or medium pile woven roller. For airless spray (dilution may be required). For further information contact the Akzo Nobel Customer Advice Centre. For joinery apply using a good quality fine filament synthetic brush.

CLEANING Wash with clean water immediately after use

HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960’s painted surfaces as they may contain harmful lead. For further information contact Brewers. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septic tanks.

GENERALINFORMATION Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened.

Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers are unable to guarantee results as it has no control over the conditions under which its products are applied.

Before using this product please ensure you have the latest information. For help or more information contact:

Brewers Tel 01323 411080 E-mail [email protected] Website www.brewers.co.uk

This information is correct at date of issue November 2009.

Albany House Ashford Road Eastbourne BN21 3TR Tel 01323 411080 Fax 01323 721435 E-mail: [email protected] Website: www.brewers.co.uk

9

ALBANY ACRYLIC GLOSSAn attractive mid sheen waterborne formulation for interior and extrerior use. Durable and washable.

AVAILABILITY


Packaging 1 & 2.5 litres.

PROPERTIES

Drying Time Under normal drying conditions touch dry 1-2 hours and recoatable after 6 hours. Allow for adequate ventilation during the drying period.

Finish Satin Gloss.


Spreading Rate up to 13m² per litre on smooth surfaces.



Volume Solids 39% White. Other colours will vary.


VOC Content EU limit value for this product (cat.A/d): 150 g/l (2007) / 130 g/l (2010) This product contains max. 49 g/l VOC.

Limitations Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period. Do not use over paints containing aluminium or zinc pigments.

PREPARATION

New Surfaces

Walls All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster or dense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Acrylic Primer Undercoat thinned with up to 10% clean water.

Timber All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper. Remove all dust. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Prime with one coat of Albany Acrylic Primer Undercoat.


10

All Metals IncludingGalvanised Surfaces must be clean and free from anything that will interfere with the materials to

be applied. Wash with hot water and liquid detergent solution to remove oil, grease or any other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. Galvanised surfaces should be pre-treated with a suitable mordant solution. Overall blackening of the surface will confirm satisfactory surface preparation.

Additional SurfacePreparation - All Metals

Non-ferrous Metals Lightly abrade to a bright (not polished) surface - excluding galvanised surfaces. Rinse thoroughly with clean water to remove all resides. Allow to dry. Prime with one coat of Albany All Purpose Primer.

Ferrous Metals Remove all millscale and rust back to clean metal. Remove all residues. Prime within theworking day with one coat of Albany All Purpose Primer.

PreviouslyDecorated Surfaces

Walls All surfaces must be sound, clean, suitably dry and free from anything that willinterfere with the adhesion of the materials to be applied e.g. dirt, grease etc.Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitableproprietary filler. Patch prime bare and filled areas with Albany Acrylic PrimerUndercoat. If after cleaning any areas are still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Primer Sealer.

Timber All surfaces must be suitably dry, and free from anything that will interfere with theadhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Remove grey and denatured surfaces by rubbing down with abrasive paper. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Treat knots with two thin coats of fresh knotting.Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot prime bare and filled areas with one coat of Albany Acrylic Primer Undercoat.

Metals All surfaces must be suitably dry, and free from anything that will interfere with theadhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime ferrous and non-ferrous metals including galvanised metal with one coat of Albany All Purpose Primer.

Walls, Timber and Metals Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces must be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward patch primed and or spot primed areas with Albany Acrylic Gloss.


11



APPLICATION Stir well before use. For walls apply using a good quality fine filament synthetic brush or medium pile woven roller. For airless spray application dilution may be required. For joinery apply using a good quality fine filament synthetic brush.

CLEANING Wash with clean water immediately after use.


GENERALINFORMATION Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened. Every care is taken to ensure that all in formation provided on this Technical Data Sheet is accurate. Brewers are unable to guarantee results as it has no control over the conditions under which its products are applied.



This information is correct at date of issue December 2009.


13

ALBANY ACRYLIC PRIMER UNDERCOATVersatile formulation for priming / undercoating timber and dry plaster.

AVAILABILITY

Colour Range White.

Packaging 1, 2.5 and 5 litres.

PROPERTIES

Drying Time Under normal drying conditions touch dry in 30 minutes and recoatable after 4 hours. Allow for adequate ventilation during the drying period.

Finish Matt.

Composition Pigment: Titanium Dioxide and extenders Binder: Acrylic polymer Solvent: Water



Dry Film Thickness 22 micrometres at 16m² per litre.

Volume Solids 35%.



Limitations For interior and exterior use. Do not apply when there is a risk of rain, air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION

New Surfaces All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper. Remove all dust. Timber with oils/extractives must be swabbed with clean dearo matised white spirit, frequently changing the face of the cloths. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

PreviouslyDecorated Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will

interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with a Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler. Patch prime bare and filled areas with Albany Acrylic PrimerUndercoat. If after cleaning any areas are still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Primer Sealer.


14



APPLICATION Stir well before use. Apply using a good quality fine filament synthetic brush to an even thickness. Lay off in the direction of the grain. Can also be applied by roller, airless or conventional spray.

CLEANING Return surplus material to container. Wash with clean water immediately after use.

MAINTENANCEINFORMATION FORCDM FILE Between maintenance redecoration surfaces may be washed with a warm water and liquid detergent solution to remove surface dirt.








15

ALBANY ALL PURPOSE PRIMERA versatile primer for many surfaces.

AVAILABILITY

Colour Range Beige.

Packaging 500ml, 1, 2.5 and 5 litres.

PROPERTIES

Drying Time Under normal drying conditions surface dry 6-8 hours and recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish Not applicable.

Composition Pigment: Titanium Dioxide, anti-corrosive pigments and extenders Binder: Long Oil Alkyd Solvent: Dearomatised White Spirit

Spreading Rate Up to10m² per litre on smooth surfaces.



Volume Solids 56%.

Flash Point 40ºC. (closed cup).


Limitations Do not apply when air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the drying period.

PREPARATION

New Surfaces

Timber All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

All MetalsIncluding Galvanised Surfaces must be clean and free from anything that will interfere with the materials to be applied. Wash with hot water and liquid detergent solution to remove oil, grease or any other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. Galvanised surfaces should be pre-treated with a suitable mordant solution. Overall blackening of the surface will confirm satisfactory surface preparation.AdditionalSurface Preparation -All metals

Non-ferrous Metals Lightly abrade to a bright (not polished) surface - excluding galvanised surfaces. Rinse thoroughly with clean water to remove all resides. Allow to dry.

Ferrous Metals Remove all millscale and rust back to clean metal. Remove all residues. Prime within the working day.


16

Previously Decorated Surfaces

Timber All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler or a two pack proprietary wood filler. Rub down witha suitable grade of abrasive paper. Remove all dust. Spot prime bare and filled areas with one coat of Albany Primer.

Metals All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime non-ferrous and ferrous metals with Albany All Purpose Primer.

Timbers And Metals Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas as required with paint system to be used.


17


COATING SYSTEM Apply one coat.

APPLICATION Stir well before use. Apply by brush or roller. On timber lay off in the direction of the grain. Prior to application, the moisture content of timber substrates should not exceed 18%.

CLEANING Return surplus material to container. Clean with a proprietary cleaner immediately after use.

MAINTENANCE INFORMATION FORCDM FILE Between maintenance redecoration surfaces may be washed with a warm water and liquid detergent solution to remove surface dirt.


GENERAL INFORMATION Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened.

Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers is unable to guarantee results as it has no control over the conditions under which its products are applied.





19

ALBANY ALUMINIUM WOOD PRIMERFor hardwood and resinous softwood.

AVAILABILITY

Colour Metallic Grey.

Packaging 500ml & 2.5 litres.

PROPERTIES

Drying Time Under normal drying conditions surface dry 4 hours and recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish N/A.

Composition Pigment: Aluminium paste and extenders Resin: Long Oil Alkyd Solvent: Dearomatised White Spirit

Spreading Rate Up to 13m² per litre depending on surface texture.



Volume Solids 52%.


VOC Content EU limit value for this product (cat.A/g): 450 g/l (2007) / 350 g/l (2010). This product contains max. 349 g/l VOC.


PREPARATION

New Surfaces All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive

paper and round sharp edges 1-3mm. Remove all dust. Timber with oils/extractives mustbe swabbed with clean white spirit, frequently changing the face of the cloths. Treatknots with two thin coats of fresh knotting. Fill any fixing holes, open joints andshallow surface defects with a suitable proprietary filler. Rub down with a suitablegrade of abrasive paper. Remove all dust.

Previously All surfaces must be suitably dry, and free from anything that will interfere with theDecorated Surfaces adhesion of the materials to be applied. Remove all loose, and failing or suspect paint.

Remove grey and denatured surfaces by rubbing down with abrasive paper or bymechanical means and round sharp edges 1-3mm. Feather edges of sound paint.Remove all dust. Organic growth must be removed and the areas treated with AlbanyFungicidal Wash. Remove any defective putty glazing, clean and prime rebates,replacement putties must be allowed to form a hard skin. Treat knots with two thincoats of fresh knotting. Fill any fixing holes, open joints and shallow surface defectswith a suitable proprietary filler. or a two pack proprietary wood filler. Rub down witha suitable grade of abrasive paper. Remove all dust. Wash remaining sound paint withhot water and liquid detergent solution to remove any contaminants, frequentlychanging the water. Wet abraded to provide a key. Rinse with clean water to removeall residues. Allow to dry. Spot prime bare and filled areas with one coat of AlbanyAluminium Wood Primer.


20



APPLICATION Stir well before use. Apply by brush or roller in the direction of the grain. Prior to application, the moisture content of the substrate should not exceed 18%.


MAINTENANCE INFORMATION FOR CDM FILE Between maintenance redecoration surfaces may be washed with a warm water and liquid detergent solution to remove surface dirt.

HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960s painted surfaces as they may contain harmful lead. For further information contact Brewers. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septic tanks.







21

ALBANY DURABLE MATT EMULSIONAlbany Durable Matt is formulated for use on new or previously painted interior wall surfaces. 500% stronger than standard vinyl matt, it provides a tough, long lasting matt finish that withstandsrepetitive cleaning.

AVAILABILITY


Packaging 2.5 and 5 litres.

PROPERTIES

Drying Time Under normal drying conditions touch dry in 2 hours, recoatable after 4 hours. Allow for adequate ventilation during the drying period.

Finish Matt.


Spreading Rate 14m² per litre on smooth surfaces.



Volume Solids 34.6% Brilliant White. Other colours will vary.


VOC Content EU limit value for this product (cat. A/a): 75g/l (2007) / 30g/l (2010) This product contains max 30 g/l VOC


PREPARATION

New Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Durable Matt Emulsion, thinned with up to 40% clean water.

Previously Decorated Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with an appropriate Filler. Patch prime bare and filled areas of masonry with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward patch primed areas with one coat of Albany Durable Matt Emulsion.


22


COATING SYSTEM Apply two coats as required.

APPLICATION Stir well before use. Apply by brush or medium pile roller. For airless spray (dilution may be required). For further information contact Brewers.



GENERAL INFORMATION Apply all products in accordance with BS 6150: 2006 Code of practice for painting of buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings and painting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened.

Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers is unable to guarantee results as it has no control over the conditions under which its products are applied.



This information is correct at date of issue September 2008.


23

ALBANY FUNGICIDAL WASHFor treating surfaces infected with organic growth contamination.

AVAILABILITY

Colour Colourless.

Packaging 1 and 5 litres.

PROPERTIES

Drying Time Under normal conditions touch dry in 2 hours. Leave for 24 hours then rinse with clean water and allow to dry.

Spreading Rate Up to 20m² per litre when diluted depending on surface suction. On textured surfaces the spreading rate will be reduced.

Wet Film Thickness Not applicable. Ensure that affected areas are well saturated during application.

Dry Film Thickness Not applicable.

Volume Solids Not applicable.


VOC Content Not applicable.

Limitations Do not apply if there is a risk of rain or frost, use as a paint additive, mix with other chemicals, or apply by power spray machines. Albany Fungicidal Wash is a surface treatment and does not provide preservation properties to any substrate.

PREPARATION

Undecorated Surfaces All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Remove all organic growth by scraping or brushing with a stiff bristle brush (not wire). Heavy long established growth is best removed by pressure washing between 1500-2000 psi (102-136 bar), wet or dry grit blasting. Care must be taken not to damage the underlying surface. The spores must then be killed with an application of Albany Fungicidal Wash diluted one volume of Fungicidal Wash with up to four volumes clean water. Leave for 24 hours and rinse with clean water. Allow to dry.

Previously All surfaces must be sound, suitably dry and free from anything that will interfere withDecorated Surfaces the adhesion of the material to be applied. Remove all loose, and failing or suspect

material by scraping or brushing with a stiff bristle brush (not wire) to a sound edge.Remove all organic growth by scraping or brushing with a stiff bristle brush (not wire).Heavy long established growth is best removed by pressure washing between 1500-2000 psi (102-136 bar), wet or dry grit blasting. Care must be taken not to damagethe underlying surface. The spores must the be killed with a application of AlbanyFungicidal Wash diluted one volume of Fungicidal Wash with up to four volumes cleanwater. Leave for 24 hours and rinse with clean water. Allow to dry.


24


COATING SYSTEM One application. When growth has been severe a second application may be necessary.

APPLICATION Apply liberally using a synthetic bristle brush and scrub well into the surface.

CLEANING Wash with clean water immediately after use.









25

ALBANY GLOSSA tough durable high gloss finish for interior and exterior use.

AVAILABILITY

Colour Refer to current Albany Literature.


PROPERTIES


Finish Gloss.

Composition Pigment: Titanium Dioxide and coloured pigments Resin: Alkyd Solvent: Dearomatised White Spirit

Spreading Rate Up to16m² per litre depending on surface texture.



Volume Solids 46% Brilliant White. Other colours will vary.




PREPARATION

New Surfaces

Timber All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with Sandtex Trade Ready Mixed Filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Prior to priming the moisture content of the substrate should not exceed 18%. Prime with one coat of Albany Wood Primer (or Albany All Purpose Primer or Albany Aluminium Wood Primer) as required. Apply one coat of Albany Undercoat.

All metals Surfaces must be clean and free from anything that will interfere with the materials toincluding galvanised be applied. Wash with hot water and liquid detergent solution to remove oil, grease or any other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. galvanised surfaces should be pre-treated with a suitable mordant solution. Overall blackening of the surface will confirm satisfactory surface preparation.


26


Additional surface preparation - all metals

Non-ferrous metals Lightly abrade to a bright (not polished) surface-excluding galvanised surfaces. Rinse thoroughly with clean water to remove all resides. Allow to dry. Prime, including galvanised surfaces, with one coat of Albany All Purpose Primer.

Ferrous metals Remove all millscale and rust back to clean metal. Remove all residues. Prime within the working day with one coat of Albany Metal Primer.

Previouslydecorated surfaces

Timber All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Prior to painting the moisture should not exceed 18%. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

Metals All surfaces must be suitably dry, and free from anything that will interfere with theadhesion of the materials to be applied. Remove all loose, and failing or suspect paint.Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime ferrousmetals with one coat of Albany Metal Primer. Spot prime non-ferrous metals includinggalvanised metal with one coat of Albany All Purpose Primer.

Timber and metals Wash remaining sound paint with hot water and liquid detergent solution to removeany contaminants, frequently changing the water. Wet abraded to provide a key. Rinsewith clean water to remove all residues. Allow to dry. Bring forward and apply overallone coat of Albany Undercoat.

27


COATING SYSTEM Apply one or two coats as required. Maintain a wet edge.

APPLICATION Stir well before use. Apply by brush to an even thickness (a fine, soft long filament bristle brush gives best results). Maintain a wet edge. On timber lay off in the direction of the grain.










29

ALBANY HIGH OPACITY SUPERCOVERA high opacity matt finish suitable for new plaster.

AVAILABILITY

Colour Range Refer to current Albany Literature.

Packaging 5 litres, (10 litres White & Magnolia).

PROPERTIES

Drying Time Under normal drying conditions touch dry 2 hours, recoatable after 4 hours. Allow for adequate ventilation during the drying period.

Finish Matt.

Composition Pigment: Titanium Dioxide, coloured pigments and extendersBinder: Vinyl acetate copolymerSolvent: Water




Volume Solids 25% White other colours will vary.


VOC Content EU limit value for this product (cat.A/a): 75 g/l (2007) / 30 g/l (2010)This product contains max. 19 g/l VOC.

Limitations For interior use only. Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the dryingperiod.

PREPARATION

New Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster ordense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany High Opacity Supercover thinned with up to 10% clean water.


interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler.Patch prime bare and filled areas with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. If after cleaning any areas still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Prime Sealer. Bring forward patch primed areas with one coat of Albany High Opacity Supercover.


30


APPLICATION Stir well before use. Apply by brush, roller or spray. For spray application dilution may be required.


MAINTENANCEINFORMATION FORCDM FILE Between maintenance redecoration surfaces may be washed with a warm water and

liquid detergent solution to remove surface dirt.

HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960’s painted surfaces as they may contain harmful lead. For further information contact Brewers. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septictanks.

GENERALINFORMATION Apply all products in accordance with BS 6150: 2006 Code of practice for painting of

buildings and BS 8000: Part 12: 1989 Code of practice for decorative wallcoverings andpainting. Under normal and frost free conditions this product will remain usable for up to two years if stored correctly and unopened.

Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers are unable to guarantee results as it has no control over theconditions under which its products are applied.

Before using this product please ensure you have the latest information.For help or more information contact:

BrewersTel 01323 411080E-mail [email protected] www.brewers.co.uk




31

ALBANY METAL PRIMERA high performance metal primer: anti corrosive and rust inhibiting.

AVAILABILITY

Colour Green.

Packaging 2.5 litres.

PROPERTIES


Finish Matt.

Composition Pigment: Titainium dioxide Zinc phosphate, Zinc Oxide and extendersResin: Long Oil AlkydSolvent: Dearomatised White Spirit




Volume Solids 43%.

Flash Point 40ºC (closed cup).

VOC Content EU limit value for this product (cat.A/i): 600 g/l (2007) / 500 g/l (2010)This product contains max. 445 g/l VOC.


PREPARATION

New Surfaces Surfaces must be clean and free from anything that will interfere with the materials to be applied. Wash with hot water and liquid detergent solution to remove oil, grease orany other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. Remove all millscale and rust back to clean metal. Remove all residues.

Previously Decorated Surfaces All surfaces must be suitably dry, and free from anything that will interfere with the

adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime bare areas with one coat of Albany Metal Primer. Wash remaining sound paint with hot water andliquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas as required by paint system to be used.


32



APPLICATION Stir well before use. Apply by brush or roller.




HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960’s painted surfaces as they may contain harmful lead. For further information contact Brewer. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septictanks.








33

ALBANY NON DRIP GLOSSHigh gloss for wood or metal.

AVAILABILITY

Colour Range Refer to current Albany literature.

Packaging 750ml & 2.5 litre.

PROPERTIES


Finish Gloss.

Composition Pigment: Titanium Dioxide and coloured pigments.Resin: Thixotropic AlkydSolvent: Dearomatised White Spirit.




Volume Solids 54% Brilliant White other colours will vary.


VOC Content EU limit value for this product (cat.A/d): 400 g/l (2007) / 300 g/l (2010)This product contains max. 289 g/l VOC.


PREPARATION

New SurfacesTimber All surfaces must be suitably dry, and free from anything that will interfere with the

adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Prior to priming the moisture content of the substrate should not exceed 18%. Prime with one coat of Albany Wood Primer.

All Metals includingGalvanised Surfaces must be clean and free from anything that will interfere with the materials to

be applied. Wash with hot water and liquid detergent solution to remove oil, grease orany other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. galvanised surfaces should be pre-treated with a suitable mordant solution. Overall blackening of the surface will confirm satisfactory surface preparation.

Additional SurfacePreparation - All MetalsNon-Ferrous Metals Lightly abrade to a bright (not polished) surface-excluding galvanised surfaces.

Rinse thoroughly with clean water to remove all resides. Allow to dry. Prime, including galvanised surfaces, with one coat of Albany All Purpose Primer.

Ferrous Metals Remove all millscale and rust back to clean metal. Remove all residues. Prime within theworking day with one coat of Albany Metal Primer.


34

Previously DecoratedSurfaces - Timber All surfaces must be suitably dry, and free from anything that will interfere with the

adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Prior to painting the moisture should not exceed 18%. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler or a twopack proprietary wood filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

Metals All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime ferrous metals with one coat of Albany Metal Primer. Spot prime non-ferrous metals including galvanised metal with one coat of Albany All Purpose Primer.

Timber and Metals Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward all spot primed areas with an additional coat of primer and allow to dry.

COATING SYSTEM Apply one or two coats as required. Maintain a wet edge.

APPLICATION Apply by brush to an even thickness (a fine, soft long filament bristle brush gives bestresults). Maintain a wet edge. On timber lay off in the direction of the grain.




HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960’s painted surfaces as they may contain harmful lead. For further information contact Brewers. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dryconditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septic tanks.


35









37

ALBANY POLYURETHANE EGGSHELL VARNISHAlbany Polyurethane Varnish produces a clear, highly durable finish on interior woodwork. It is easy toapply, washable and resists knocks, scratches and hot drinks.

AVAILABILITY

Colour Clear.

Packaging 1 and 2.5 litres.

PROPERTIES

Drying Time Under normal drying conditions touch dry in 4-6 hours, recoatable after 16-24 hours. Allow for adequate ventilation during the drying period.

Finish Eggshell.

Composition Resin: Urethane and Alkyd Resins Solvent: Dearomatised White Spirit






VOC Content EU limit value for this product (cat.A/e): 500 g/l (2007) / 400 g/l (2010) This product contains max. 399 g/l VOC.


PREPARATION

New Surfaces

Timber All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Timber with oils/extractives must be swabbed with clean methylated spirits, frequently changing the face of the cloths. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust.

Previously All surfaces must be suitably dry, and free from anything that will interfere with the vanished surfaces adhesion of the materials to be applied. Remove all loose, and failing or suspect varnish and any grey denatured timber. Prior to coating, the moisture should not exceed 18%. Feather edges of sound varnish. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot varnish bare and filled areas with Albany Eggshell Varnish. Wash remaining sound varnish with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of the Albany Eggshell Varnish.


38


COATING SYSTEM Apply two or three full coats as required. Maintain a wet edge.











39

ALBANY POLYURETHANE GLOSS VARNISHAlbany Polyurethane Varnish produces a clear, highly durable finish on interior woodwork. It easy to apply, washable and resists knocks, scratches and hot drinks.

AVAILABILITY

Colour Clear.


PROPERTIES


Finish Gloss.









PREPARATION

New Surfaces


Previously All surfaces must be suitably dry, and free from anything that will interfere with the varnished surfaces adhesion of the materials to be applied. Remove all loose, and failing or suspect vanish and any grey denatured timber. Prior to coating, the moisture should not exceed 18%. Feather edges of sound varnish. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot varnish bare and filled areas with Albany Gloss Varnish. Wash remaining sound varnish with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of the Albany Gloss Varnish.


40


COATING SYSTEM Apply two or three coats as required. Maintain a wet edge.











41

ALBANY POLYURETHANE MATT VARNISHAlbany Polyurethane Varnish produces a clear, highly durable finish on interior woodwork. It easy to apply, washable and resists knocks, scratches and hot drinks.

AVAILABILITY

Colour Clear.


PROPERTIES


Finish Matt.









PREPARATION

New Surfaces


Previously All surfaces must be suitably dry, and free from anything that will interfere with the varnished surfaces adhesion of the materials to be applied. Remove all loose, and failing or suspect varnish and any grey denatured timber. Prior to coating, the moisture should not exceed 18%. Feather edges of sound varnish. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot varnish bare and filled areas with Albany Matt Varnish. Wash remaining sound varnish with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of the Albany Matt Varnish.


42













43

ALBANY PRIMER SEALERA dual purpose, alkali resisting primer, ideal for dry, aged plaster.

AVAILABILITY

Colour Range Pale Cream.

Packaging 1, 2.5 & 5 litres.

PROPERTIES

Drying Time Under normal drying conditions surface dry 4 hours recoatable after 16 hours. Allow for adequate ventilation during the drying period.

Finish Pale Cream.

Composition Pigment: Titanium Dioxide and extendersResin: Epoxy esterSolvent: Dearomatised White Spirit

Spreading Rate Up to 15m² per litre smooth surfaces.



Volume Solids 38%.


VOC Content EU limit value for this product (cat.A/g): 750 g/l (2007) / 750 g/l (2010)This product contains max. 499 g/l VOC.


PREPARATION

New Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Prime surfaces as required including powdery, polished plaster or dense surfaces with Albany Primer Sealer.

Previously DecoratedSurfaces All surfaces must be sound, clean, suitably dry and free from anything that will

interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler.Patch prime bare and filled areas with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. If after cleaning any areas still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Primer Sealer.


44














45

ALBANY RED OXIDE PRIMERProvides initial protection for iron and steel surfaces.

AVAILABILITY

Colour Range Red Oxide.

Packaging 2.5 & 5 litres.

PROPERTIES



Composition Pigment: Iron oxide and extendersResin: Long Oil AlkydSolvent: Dearomatised White Spirit

Spreading Rate 15m² per litre on smooth surfaces.



Volume Solids 50%.

Flash Point 40ºC.

VOC Content EU limit value for this product (cat.A/i): 600 g/l (2007) / 500 g/l (2010)This product contains max. 499 g/l VOC.


PREPARATION

New Surfaces Surfaces must be clean and free from anything that will interfere with the materials to be applied. Wash with hot water and liquid detergent solution to remove oil, grease orany other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. Remove all millscale and rust back to clean metal. Remove all residues. Prime within the working day with one coat of Albany Red Oxide Primer.

Previously DecoratedSurfaces All surfaces must be suitably dry, and free from anything that will interfere with the

adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime bare areas with one coat of Albany Red Oxide Primer. Wash remaining sound paint with hot waterand liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of Albany Red Oxide Primer.


46





HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960’s painted surfaces as they may contain harmful lead. For further information contact the Brewers. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septictanks.









47

ALBANY SMOOTH DURABLE EGGSHELLA durable sheen finish with a smooth even film.

AVAILABILITY

Colour Refer to current Albany Literature.


PROPERTIES


Finish Eggshell.

Composition Pigment: Titanium Dioxide, coloured pigments and extenders Resin: Long Oil Alkyd Solvent: Dearomatised White Spirit






VOC Content EU limit value for this product (cat.A/d): 400 g/l (2007) / 300 g/l (2010). This product contains max. 299 g/l VOC.


PREPARATION

New Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Prime all surfaces including powdery, polished plaster or dense surfaces with Albany Primer Sealer.

Previously All surfaces must be sound, clean, suitably dry and free from anything that willDecorated Surfaces interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove

all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust.Organic growth must be removed and the areas treated with Albany Fungicidal Wash.Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler.Patch prime bare and filled areas with Albany Primer Sealer. Wash remaining soundpaint with hot water and liquid detergent solution to remove any contaminants,frequently changing the water. Any glossy or eggshell surfaces should be wet abradedto provide a key. Rinse with clean water to remove all residues. Allow to dry. If aftercleaning any areas still contaminated with substances likely to cause staining and/orbleeding, patch prime with one coat of Albany Primer Sealer. Bring forward patchprimed areas with one coat of Albany Smooth Durable Eggshell.


48






HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960s painted surfaces as they may contain harmful lead. For further information contact the Brewers. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septic tanks.







49

ALBANY SMOOTH MASONRY PAINTA durable, flexible smooth matt finish for exterior masonry.

AVAILABILITY


Packaging 2.5, 5 & 10 litres.

PROPERTIES

Drying Time Under normal drying conditions touch dry 2 hours, recoatable after 6 hours.

Finish Matt.

Composition Pigment: Titanium Dioxide, light fast coloured pigments and extenders Binder: Vinyl acetate copolymer Solvent: Water

Spreading Rate Up to 10m² per litre. On textured / porous surface the spreading rate will be reduced.



Volume Solids 32.6% Brilliant White. Other colours will vary.


VOC Content EU limit value for this product (cat.A/c): 75 g/l (2007) / 40 g/l (2010) This product contains max. 1g/l VOC.

Limitations Do not apply when there is a risk of rain, air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period. Do not use on bitumen coatings. The decoration of Fletton brickwork either facings or commons is not recommended.

PREPARATION

New Surfaces All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Surfaces with suction (porous surfaces) should be treated with an application of Albany Stabilising Solution.

Previously All surfaces must be sound, suitably dry and free from anything that will interfere withDecorated Surfaces the adhesion of the material to be applied. Remove all loose, and failing or suspect

material by scraping or brushing with a stiff bristle brush (not wire) to a sound edge.Organic growth must be removed and the areas treated with Albany Fungicidal Wash.For surfaces in poor condition mechanical means may be necessary e.g. pressure washing between 1500-2000 psi (102-136 bar), proprietary paint removal system, wet ordry grit blasting. Care must be taken not to damage the underlying surface. Fill cracksand small defects in masonry surfaces with a suitable proprietary filler and finish tomatch existing. Stabilise all bare, filled and previously decorated chalking areas with anapplication of Albany Stabilising Solution. Wash any soundly adhering gloss paintedsurfaces with hot water and liquid detergent solution to remove any contaminantsfrequently changing the water. Wet abrade to provide a key. Rinse thoroughly withclean water to remove all residues.


50



APPLICATION Stir well before use. Apply by brush, medium or long pile roller depending on surface texture, or by airless spray. For airless spray use a minimum fluid pressure of 2000psi (136 bar) and a minimum tip size of 0.018 thou. Mask as necessary with a wet strength grade masking paper.



HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960s painted surfaces as they may contain harmful lead. For further information contact Brewer. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septic tanks.







51

ALBANY SOFT SHEEN EMULSIONA subtle soft sheen for interior walls and ceilings.

AVAILABILITY

Colour Range Refer to current Albany Literature.


PROPERTIES


Finish Mid Sheen.





Volume Solids 33.6% Brilliant White other colours will vary.


VOC Content EU limit value for this product (cat.A/a): 75 g/l (2007) / 30 g/l (2010)This product contains max. 1g/l VOC.


PREPARATION

New Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster ordense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Soft Sheen Emulsion thinned with up to 10% clean water.

Previously DecoratedSurfaces All surfaces must be sound, clean, suitably dry and free from anything that will

interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler.Patch prime bare and filled areas with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. If after cleaning any areas still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Primer Sealer. Bring forward patch primed areas with one coat of Albany Soft Sheen Emulsion.


52















53

ALBANY STABILISING SOLUTIONA penetrating sealer for masonry surfaces.

AVAILABILITY

Colour Clear.


PROPERTIES

Drying Time Under normal drying conditions touch dry after 2 hours, recoatable after 16 hours.


Composition Resin: Epoxy EsterSolvent: Dearomatised White Spirit

Spreading Rate Up to 6m² per litre. On textured and surfaces with suction the spreading rate will be reduced.



Volume Solids 24%.


VOC Content EU limit value for this product (cat.A/h): 750 g/l (2007) / 750 g/l (2010)This product contains max. 565 g/l VOC.

Limitations Do not apply when there is a risk of rain, air or substrate temperatures are likely to fall below 5ºC or when the relative humidity is above 80% during application or the dryingperiod. Do not apply to bitumen coatings. The decoration of Fletton brickwork either facings or commons is not recommended.

PREPARATION

New Surfaces All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the material to be applied. Surfaces with suction (porous surfaces) should be treated with an application of Albany Stabilising Solution.

Undecorated Surfaces All surfaces must be sound, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Remove all organic growth by scraping or brushing with a stiff bristle brush (not wire). Heavy long established growth is best removed by pressure washing between 1500-2000 psi (102-136 bar), wet or dry grit blasting. Care must be taken not to damage the underlying surface. The spores must bekilled with an application of Albany Fungicidal Wash diluted one volume of Fungicidal Solution with up to four volumes clean water. Leave for 24 hours and rinse with clean water. Allow to dry. Fill cracks and small defects in masonry surfaces with a suitable proprietary filler and finish to match existing. Stabilise all bare, filled and decorated chalking areas with an application of Albany Stabilising Solution.


54

Previously Decorated Surfaces All surfaces must be sound, suitably dry and free from anything that will interfere with

the adhesion of the material to be applied. Remove all loose, and failing or suspect material by scraping or brushing with a stiff bristle brush (not wire) to a sound edge. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. For surfaces in poor condition mechanical means may be necessary e.g. pressure washing between 1500-2000 psi (102-136 bar), proprietary paint removal system, wet ordry grit blasting. Care must be taken not to damage the underlying surface. Fill cracks and surface defects in masonry surfaces with a suitable proprietary filler and finish to match existing. Stabilise all bare, filled and previously decorated chalking areas with an application of Albany Stabilising Solution.

COATING SYSTEM Apply in one liberal coat until suction, porous, friable or chalking surfaces are stabilised. Do not over stabilise.

APPLICATION Apply by brush.




HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960’s painted surfaces as they may contain harmful lead. For further information contact Brewers. When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septic

tanks.





BrewersTel 01323 411080 E-mail [email protected] Website www.brewers.co.uk




55

ALBANY UNDERCOAT An excellent foundation for Albany Gloss. For new work and redecoration.

AVAILABILITY



PROPERTIES


Finish Matt.

Composition Pigment: Titanium Dioxide, coloured pigments and extendersResin: Long Oil AlkydSolvent: Dearomatised White Spirit




Volume Solids 62.47% White . Other colours will vary.




PREPARATION

New SurfacesTimber All surfaces must be suitably dry, and free from anything that will interfere with the

adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with Sandtex Trade Ready Mixed Filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Prior to priming the moisture content of the substrate should not exceed 18%. Prime with one coat of Albany Wood Primer.

All Metals including Galvanised Surfaces must be clean and free from anything that will interfere with the materials to

be applied. Wash with hot water and liquid detergent solution to remove oil, grease or any other contaminants, frequently changing the water. Rinse thoroughly with clean water. Allow to dry. Galvanised surfaces should be pre-treated with a suitable mordant solution. Overall blackening of the surface will confirm satisfactory surface preparation.

Additional Surface Preparation - All MetalsNon-Ferrous Metals Lightly abrade to a bright (not polished) surface - excluding galvanised surfaces. Rinse

thoroughly with clean water to remove all resides. Allow to dry. Prime, including galvanised surfaces, with one coat of Albany All Purpose Primer.


56

Ferrous Metals Remove all millscale and rust back to clean metal. Remove all residues. Prime within theworking day with one coat of Albany Metal Primer.

Previously Decorated Surfaces - Timber All surfaces must be suitably dry, and free from anything that will interfere with the

adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Prior to painting the moisture should not exceed 18%. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Crown Trade Fungicidal Solution. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler or a two pack proprietary wood filler. Rub down with a suitable grade of abrasive paper. Remove all dust.

Metals All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime ferrous metals with one coat of Albany Metal Primer. Spot prime non-ferrous metals including galvanised metal with one coat of Albany All Purpose Primer.

Timber and Metals Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed area with one coat of Albany Undercoat.







57









59

ALBANY VINYL MATT EMULSIONA durable full bodied matt finish with good obliteration.

AVAILABILITY


Packaging 1, 2.5, 5 litres, (10 litres Brilliant White & Magnolia).

PROPERTIES


Finish Matt.





Volume Solids 30% Brilliant White other colours will vary.


VOC Content EU limit value for this product (cat.A/a): 75 g/l (2007) / 30 g/l (2010)This product contains max. 1 g/l VOC.


PREPARATION

New Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster or dense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Vinyl Matt Emulsion thinned with up to 20% clean water.


interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler. Patch prime bare and filled areas with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. If after cleaning any areas still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Prime Sealer. Bring forward patch primed areas with one coat of Albany Vinyl Matt Emulsion.


60






HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take special precautions during the surface preparation of pre 1960’s painted surfaces as they may contain harmful lead. For further information contact Brewers.When preparing all surfaces avoid the inhalation of dust and/or metal particles. Wear a suitable facemask. Material Safety Data Sheets for this and all other Albany products are freely available from the place of purchase or the address below. Store in secure dry conditions inaccessible to children or animals. Containers should be kept closed during storage. Do not empty into drains, watercourses or access routes to septictanks.



Every care is taken to ensure that all information provided on this Technical Data Sheet is accurate. Brewers Ltd are unable to guarantee results as it has no control over theconditions under which its products are applied.



This information is correct at date of issue July 2010.



61

ALBANY VINYL SILK EMULSIONAn attractive even sheen with excellent colour retention.

AVAILABILITY


Packaging 2.5, 5 litres, (10 litres Brilliant White & Magnolia)

PROPERTIES


Finish Silk.





Volume Solids 25.01% Brilliant White other colours will vary.


VOC Content EU limit value for this product (cat.A/b): 150 g/l (2007) / 100 g/l (2010)This product contains max. 2 g/l VOC.


PREPARATION

New Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied. Powdery, polished plaster ordense surfaces should be primed with Albany Primer Sealer. Porous surfaces should be ‘mist’ coated with Albany Vinyl Silk Emulsion thinned with up to 10% clean water.


interfere with the adhesion of the materials to be applied e.g. dirt, grease etc. Remove all loose, failing or suspect paint. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, cracks and shallow surface defects with a suitable proprietary filler. Patch prime bare and filled areas with Albany Primer Sealer. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Any glossy or eggshell surfaces should be wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. If after cleaning any areas still contaminated with substances likely to cause staining and/or bleeding, patch prime with one coat of Albany Prime Sealer. Bring forward patch primed areas with one coat of Albany Vinyl Silk Emulsion.


62















63

ALBANY WOOD PRIMERFor non resinous softwood joinery.

AVAILABILITY

Colour Range White and Pink.

Packaging 500ml, 1, 2.5 and 5 litre.

PROPERTIES


Finish Eggshell.

Composition Pigment: Titanium Dioxide and extendersResin: Long Oil AlkydSolvent: Dearomatised White Spirit




Volume Solids 57%.




PREPARATION

New Surfaces All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the materials to be applied. Rub down with a suitable grade of abrasive paper and round sharp edges 1-3mm. Remove all dust. Timber with oils/extractives

must be swabbed with clean dearomatised white spirit, frequently changing the face of the cloths. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. Rub down with a suitable grade of abrasive paper.

Previously DecoratedSurfaces All surfaces must be suitably dry, and free from anything that will interfere with the

adhesion of the materials to be applied. Remove all loose, and failing or suspect paint. Remove grey and denatured surfaces by rubbing down with abrasive paper or by mechanical means and round sharp edges 1-3mm. Feather edges of sound paint. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Remove any defective putty glazing, clean and prime rebates, replacement putties must be allowed to form a hard skin. Treat knots with two thin coats of fresh knotting. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary filler. or a two pack proprietary wood filler. Rub down with a suitable grade of abrasive paper. Remove all dust. Wash remaining sound paint with hot water and liquid detergent solution to remove any contaminants, frequentlychanging the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Spot prime all bare and filled areas.


64


APPLICATION Stir well before use. Apply by brush or roller in the direction of the grain. Prior to priming, the moisture content of the substrate should not exceed 18%.













65

ALBANY YACHT VARNISHAlbany Yacht Varnish is specially formulated for use on interior and exterior woodwork to provide aclear high build gloss finish. It is suitable for timber which is exposed to marine environments but notfor timber continuously immersed in salt or fresh water.

AVAILABILITY

Colour Clear.


PROPERTIES


Finish Gloss.









PREPARATION

New Surfaces


Previously All surfaces must be suitably dry, and free from anything that will interfere with the varnished surfaces adhesion of the materials to be applied. Remove all loose, and failing or suspect varnish and any grey denatured timber. Prior to coating, the moisture should not exceed 18%. Feather edges of sound varnish. Remove all dust. Organic growth must be removed and the areas treated with Albany Fungicidal Wash. Fill any fixing holes, open joints and shallow surface defects with a suitable proprietary wood filler to match the colour of the bare timber. Rub down with a suitable grade of abrasive paper. Remove all dust. Spot varnish bare and filled areas with Albany Yacht Varnish. Wash remaining sound varnish with hot water and liquid detergent solution to remove any contaminants, frequently changing the water. Wet abraded to provide a key. Rinse with clean water to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of the Albany Yacht Varnish.


66













albany technical data sheets

Documents