air motor radial piston type - taiyo america · 2019. 1. 23. · air motor - radial piston type...

Air Motor Radial Piston TypeUTAM4 SeriesCatalog HY08-T1914-B1/NA

Air Motor - Radial Piston TypeSeries UTAM4

Catalog HY08-T1914-B1/NA

Taiyo AmericaSt. Marys, OhioUSAwww.taiyoamericacylinders.com

Series U100S Series U140 H-8

Grease Suction Unit

Series U160S Series U250

Taiyo America offers products that are designed to meet and exceed the most demanding application requirements. Our extensive hydraulic cylinder product line offers OEM’s and End Users cylinder solutions that provide value through reduced maintenance, increased productivity, and long service life. Taiyo America’s wide breadth of product encompasses NFPA, ISO, and Custom designed products in a multitude of configurations and sizes.

Operating Principles 1

How To Order 2

Model Numbers, Product Specifications 3

Inside Product Structure 4

Product Dimensions 5-8

Basic Circuits 9

Offer of Sale 10

Table of Contents

In line with our policy of continuing product improvement, specifications and information contained in this catalog are subject to change.# Copyright ©2019 by Taiyo America. All rights reserved.PRINTED IN THE U.S.A.

WARNINGFAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from the Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having expertise. It is important that you analyze all aspects of your application, including consequences of any failure and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met.

The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Taiyo America and its subsidiaries at any time without notice.

Offer of SaleThe items described in this document are hereby offered for sale by Taiyo America, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by provisions stated on a separate page of the document entitled ‘Offer of Sale’.



1 Taiyo AmericaSt. Marys, OhioUSAwww.taiyoamericacylinders.com

Operating Principles

Operational Principle of Radial Piston Type Air Motor

Drive shaft with key

Robust painted aluminum housing

Connecting rodCrankshaft

Piston

Ports. The direction of rotation depends on which port is supplied with air/vented.

Valve function that alternately supplies and vents air to/from the cylinders as the motor rotates.

Mechanism

In radial piston type air motor, each piston connected with crankshaft by connecting rod, interlocking with rotary valve which provides compressed air to each cylinder through A port, accordingly corresponding pis-ton thrusts crank then obtains turning force. While B port on the opposite side functions exhaust port.

Handling Instructions & CautionsMounting

- When installing motors, be sure all couplings, sprockets, attachments, etc. are properly guarded. Failure to comply could result in serious bodily harm or property damage.

- When air is admitted to one port on reversible tools, the other port becomes an exhaust port; if it is plugged, it will produce a severe "back pressure" and greatly reduce speed and power of the motor. Do not plug exhaust ports of motor. Use mufflers.

- In corrosive or dusty atmospheres, it is recommended that air lines be equipped with micro (coalescing) filters, air filters and exhaust mufflers.

Advantages- Radial piston type air motors have more positive start-

ing, better speed control at low speeds, and slightly better stopping characteristics than vane motors.

- In addition, they have slightly lower air consumption at the lower speeds.

- Output torque is developed by pressure acting on pistons; there are 3 or 5 pistons per motor.

- Most motors have 3 or 5 pistons, but there is some disagreement as to which number is preferable since both designs give excellent performance.

- Power developed by piston motors increases with inlet pressure, number of pistons, piston area, stroke and speed.

- Primary factor limiting speed in a piston motor is the inertia of the moving parts.

- Radial piston type air motors are basically low-speed devices capable of reaching free speeds up to 1500 rpm.

- They can lug heavy loads at all speeds and are particularly adaptable to applications requiring high starting torque and slow speed.

Piping- Mount the lubricator, regulator, filter and directional

control valve as close to the motor as possible. It is possible to save air consumption.

- Before mounting, flush pipe with compressed air and remove cutting powder, cutting oil and dust.

- When steel tubes are used for piping, be sure they are zincplated pipes.

- Do not plug exhaust ports of directional control valve to keep away from “back pressure”.

Lubrication- Air lines should be equipped with lubricators.Recommended supply of lubricant is 5 drop/min. at 70 psig (Setting pressure). Mount the lubricator as close to the motor as possible.Environmental conditions Keep away from:- Dust- Moisture- Corrosive gases and chemicals or their solutions- More than 158OF temperature and direct sunlight.




Product Design

How To OrderOrder motors, mountings (except geared type) and accessories as separate line items.

Direct DriveMounting Kit for Direct Drive Motor

Modular F.R.L. Combination Set Muffler

UTAM4-

UTAM4-

S

G

Geared Drive

Accessories

010

015 005F

1 Horse Power010 0.10 hp015 0.17 hp030 0.31 hp

1 Horse Power010 0.09 hp015 0.15 hp030 0.27 hp

2 Mounting StyleF Flange Mtg.L Foot Mtg.

3 Gear Ratio005 1/5010 1/10020 1/20

Port Size (PT) Model No.1/4 SA-83/8 SA-10

Series

Series

Standard

Geared

(*including Muffler as standard)

(*including Muffler as standard)

For UTAM4-010 UTAM4-015 UTAM4-030

Kit No. FM-010 FM-015 FM-030

Flange Mounting

Kit

IncludingFlange Mtg. (1)Screw (3)



Kit No. LM-010 LM-015 LM-030Foot

Mounting Kit

IncludingFoot Mtg. (1)Screw (3)



Port Size (NPT) TRIO TWIN Micro (Coalescing) Filter1/4 UCFRL-08 UCKL-08 UCFF-083/8 UCFRL-10 UCKL-10 UCFF-101/2 UMFRL-15 UMKL-15 UMFF-153/4 UMFRL-20 UMKL-20 UMFF-20




Product Design

• Taiyo air motors are designed for use in industrial applications such as powering air driven machinery, raising foundry copes and drags, rotating a turnable, mixing paint, powering cranes, valve actuation and power source for mechanical hands.

• Speed could be easily controlled by flow adjustment from 100 r.p.m. up to Max. speed.

• Compact size, light in weight and simple in structure are features of all models.

• Taiyo air motors can be mounted any way you like -Flange mounting and foot mounting are available.

• Air lines should be equipped with lubricators. Mount the lubricator as close to the motor as possible.

Media Filtered (Under 40µm) and lubricated air

*Max. Operating Pressure 90 psig (7kgf/cm2)

Ambient and media

temperature32-158°F (0-70°C) at no freezing condition.

**Lubrication for line lubricators Should be necessary/Recommended oil; misting-type oils rated 150-200 SSU at 100°F (38°C)/ISO VG 32

**Recommended gear oil Same as Shell Oil Co.Alvania # EP RIO 71039 Grade “00” or Sun Petroleum Products Prestige 740 AEP Grade “00”

* These Motors must be operated with sufficient load to prevent speed from exceeding maximum allowable speed shown on performance curve. Do not operate motors at more than 80% of or near Max. power speed.

** The oil used must be compatible with materials of construction. Contact your lubricant supplier and the builder of equipment to be lubricated to obtain lubricant recommendations.

The proper grades of grease and oil are essential to the economical operation of any air motor.

Note: All the eight part numbers above are available in stock at St Marys location.

Stocked at our

St. Marys location

Model Number TypeMount-

ing Style

Gear Ratio

*Max. PowerStarting Torque

ft-lb

Stall Torque

ft-lb

Max Allowable Shaft

LoadWeight

Horse Power Torque Speed

RPM

Air Con-sumption

SCFM Radial Load lb

Thrust Load lb

Direct Drive

Flange Mount

Foot Mount

X UTAM4 010 S Direct Drive 0.10 0.47 1100 7 0.51 0.87 22 13 3.2 3.3 4.6

UTAM4 010 F G005 Gear Drive Flange 1/5 0.09 2.09 220 7 2.16 3.61 55 33 - 6.6 6.4

X UTAM4 010 L G005 Gear Drive Foot 1/5 0.09 2.09 220 7 2.16 3.61 55 33 - 6.6 6.4


UTAM4 010 L G010 Gear Drive Foot 1/10 0.09 4.19 110 7 4.33 7.22 121 55 - 6.6 6.4


X UTAM4 010 L G020 Gear Drive Foot 1/20 0.09 8.44 55 7 8.66 15.55 242 99 - 6.6 6.4

X UTAM4 015 S Direct Drive 0.17 1.01 900 9.2 1.44 2.16 31 22 5.5 5.7 7.5

UTAM4 015 F G005 Gear Drive Flange 1/5 0.15 4.33 180 9.2 6.49 9.38 86 55 - 11.2 11.0

UTAM4 015 L G005 Gear Drive Foot 1/5 0.15 4.33 180 9.2 6.49 9.38 86 55 - 11.2 11.0

X UTAM4 015 F G010 Gear Drive Flange 1/10 0.15 8.66 90 9.2 12.99 19.48 176 77 - 11.2 11.0




X UTAM4 030 S Direct Drive 0.31 2.16 750 14.1 3.46 4.33 44 31 10.1 10.6 14.1


X UTAM4 030 L G005 Gear Drive Foot 1/5 0.27 9.38 150 14.1 15.15 19.48 110 66 - 19.6 19.4


X UTAM4 030 L G010 Gear Drive Foot 1/10 0.27 19.48 75 14.1 30.31 38.97 220 99 - 19.6 19.4






Parts List

Inside Structure/Direct Drive

UTAM4-010-015

UTAM4-010-030

No. Name Material Quantity

Casing Aluminum alloy 1

Cylinder cover Aluminum alloy 3 (5)

End cover Synthetic resin 1

Connecting rod Aluminum alloy 3 (5)

Piston Brass casting 3 (5)

Sleeve Cast iron 3 (5)

Piston pin Carbon steel 3 (5)

Ring Carbon steel 2

Thrust washer Carbon steel 2

Crank pin Carbon steel 1

Valve bushing Cast iron 1

Balance weight Carbon steel 1

Shaft Chrome molybdenum steel 1

Liner Synthetic resin 3 (5)

No. Name Material Quantity

Bearing — 1

Bearing — 1

Needle bearing — 1

Snap ring — 1

Snap ring — 1

2 Grease nipple — 1

2 Copper rivet — 1

2 Oil seal N.B.R. 1

2 Gasket N.B.R. 3 (5)

2 Gasket N.B.R. 3 (5)

2 Gasket N.B.R. 1

2 Key — 1

2 Muffler — 1

Parts List

(*) Quantity is for UTAM4-30.




Dimensions

MMCC

HT

HH

DD

LM

4-KM

FL

BB1.69(43)

0.12(3)

EE

(AA)

EA

FH

AB

Dimensions/Direct Drive/UTAM4-010-015

Standard

*Tolerance-.00098" (.025)

**Tolerance-.0004" (.011)

Symbol \Model No.

AA BB CC DD DF EA EE *FF **FH FL GG GH GL HH HT KK KL KM

UTAM4-010 7.56 (192)

4.45 (113)

5.12 (130)

4.53 (115)

5 (127)

1.14 (29)

1.42 (36)

ø1.6535(ø42)

ø2.6772(ø68)

0.20 (5)

0.67 (17)

0.39 (10)

0.79 (20)

1.89 (48)

2.64 (67)

(M5x0.8) 0.31 (8)

ø0.24(ø6)

UTAM4-015 8.86 (225)

5.39 (137)

6.46 (164)

5.59 (142)

5.98 (152)

1.42 (36)

1.77 (45)

ø1.8898 (ø48)

ø3.0709(ø78)

0.28 (7)

0.75 (19)

0.47 (12)

1.10 (28)

2.36 (60)

3.23 (82)

(M6x1) 0.47 (12)

ø0.28(ø7)

Symbol \Model No.

LL LM MM NA NB NC NN PA PB PP KEY

a **b d e f g

UTAM4-010 ø2.17 (ø55)

ø3.15(ø80)

2.83 (72)

1.02 (26)

1.77 (45)

2.20 (56)

2.36 ± .004 (60 ± 0.1)

1.97(50)

3.15 (80)

3.70 (94)

0.91 (23)

ø0.3937 (ø10)

0.118 (3)

0.118 (3)

0.071 (1.8)

0.787 (20)

UTAM4-015 ø2.44 (ø62)

ø3.62(ø92)

o 3.39 (o 86)

1.30 (33)

1.97 (50)

2.48 (63)

2.76 ± .004 (70 ± 0.1)

2.76 (70)

3.94 (100)

4.33 (110)

1.18 (30)

ø0.4724 (ø12)

0.157 (4)

0.157 (4)

0.098 (2.5)

1.063 (27)

Shaft end

f

e

d

b

ag (Key length)

GH GG GL

BB (43)1.69

0.12

EE

(AA)

(3)

FF

Silencer for exhaust

PT1/8 (Exhaust port)

Exhaust port PT1/8(Plugged)

2×2-NPT1/4

AB

2.36 (60)

CC

8HT

HH

DDLL3-KK

Depth KL

Port B: CounterclockwisePort A: Clockwise

With Foot Mounting

With Flange Mounting

inch (mm)

HT

0.35(9)

(AA)

2-0.35 (9) Holes

DF

Spot facing Ø0.67 (Ø17)depth 0.02 (0.5)

PP

PAPBCC

NA NBNC

EE BB1.69(43)

NN

AB




Dimensions

Dimensions/Direct Drive/UTAM4-030

Standard Shaft end1.57(40)1.38(35) (Key length)

(5) 0.1969

0.1969 (5)

0.118(3)

Ø0.6299 (Ø16)

2.99(76)

7.40(188)

0.39(10)

(93.5)3.68

3.46(88)

7.15(181.5)

Ø3.07Ø78

Ø2.4409(Ø62)

0.59(15)

0.85(21.5)

1.34(34)

10.67(271)

209(53)

2.32(59)0.15(4)

6.26(159)

5-M6×1Depth 0.47 (12)


PT3/8(Exhaust port)2×2-NPT3/8

AB

Port B: Counterclockwise

Port A: Clockwise


With Flange Mounting

With Foot Mounting

(□106)□4.17

Ø0.354-(Ø9)

Ø3.7008(Ø94)

AB7.15(181.5)

10.67(271)

2.09(53)

1.85(47)

6.26(159)

2.32(59)

3.46(88)

0.35(9)

0.12(3)

7.40 (188)

3.68(93.5)

Ø3.07(Ø114)

3.94 (100)5.12 (130)7.40 (188)

3.68(93.5)

(188.5)7.42

2.09(53)

6.26(159)

2.32(59)

1.73(44)

2.76(70)

3.39(86)

2-0.43 (11) HolesSpot facing Ø0.87

(Ø22) depth 0.02 (0.5)

5.67(144)

0.39(10)

10.67(271)

3.74±.004(95±0.1)

AB




7

Dimensions

With Flange MountingTAM4-010FGTAM4-015FG

With Foot MountingTAM4-010LGTAM4-015LG

Dimension/Geared Drive/UTAM4-015 GFL

**Tolerance-.0005" (.013)

*Tolerance-.0016" (.04)

Symbol \Model No.

AB BC BD CD CE *DE DG EG EL FA FB GA GB GL GT HA

UTAM4-010 G 10.45 (265.5)

7.38 (187.5)

7.57 (192.5)

6.10(155)

5.28 (134)

ø 5.7087 (Ø145)

2.17 (55)

1.38(35)

2.52(64)

0.12(3)

1.57 (40)

0.39(10)

2.80(71)

0.79(20)

3.60(91.5)

3.05(77.5)

UTAM4-015 G 12.32 (313)

8.78 (223)

9.06 (230)

6.50 (165)

6.06 (154)

ø 5.8268 (ø148)

2.56(65)

1.85(47)

3.54(90)

0.16(4)

2.56(65)

0.47(12)

2.83(72)

1.10(28)

4.13(105)

3.25(82.5)

Symbol \Model No.

HB HL JA JB KA KB L MA MB NF P KEY

a **b d e f g

UTAM1-010 G 3.35 (85)

6.10 (155)

3.05(77.5))

5.48(138)

ø 0.43 (ø 11)

ø 0.35 (ø 9)

0.55(14)

ø 6.69 (ø 170)

1.77(45)

0.39(10)

ø 4.41 (ø 112)

1.18 (30)

0.7087 (ø18)

0.2362 (6)

0.2362 (6)

0.14 (3.5)

1.06 (27)

UTAM015 G 3.54(90)

6.50(165)

3.25(82.5)

6.06(154)

Ø 0.43 (ø 11)

ø 0.43 (ø 11)

0.71(18)

ø 7.28 (ø 185)

2.17(55)

0.47(12)

ø 4.92 (ø 125)

1.57(40)

0.8661 (ø22)

0.2362(6)

0.2362(6)

0.14 (3.5)

1.38(35)

inch (mm)

Port A: ClockwisePort B: Counterclockwise

Deceleration ratio 1/5 to 1/30 Shaft end

f

e

d

b

ag (Key length)

Port B: ClockwisePort A: Counterclockwise

f

e

d

b

AB

BCEG

(AB)1.69(43)

FA GA

DE L


PT1/4(Exhaust port)


2×2-NPT1/4

GT GL

MA

CD

JA

HA

HL

4-KA

Deceleration ratio 1/40 to 1/200

P

DGDG

GB

JB

4-KBCE

NF

AB

BD

(AB)

1.69(43)

HB

L

MB FBEL





Dimensions

**Tolerance-.0005" (.013)

*Tolerance-.0016" (.04)

Symbol \Model No.

AB BC BD CD CE *DE DG EG EL FA FB GA GB GT

UTAM4-030 G 14.33 (364)

10.28 (261)

10.47 (266)

7.36(187)

6.69 (170)

ø 6.6929 (ø170)

2.76 (70)

1.97(50)

4.72(120)

0.16(4)

3.54 (90)

0.59(15)

3.46(88)

4.86(123.5)

Symbol \Model No.

HA HB HL JA JB KA KB L MA MB NF P KEY

a **b d e f g

UTAM1-030 G 3.94(100)

4.33 (110)

7.64 (194)

3.70(94)

7.15(181.5)

ø 0.43 (ø 11)

ø 0.43(ø 11)

0.87(22)

ø 8.46 (ø 215)

2.56(65)

0.59(15)

ø 5.98 (ø 152)

1.77 (45)

1.1024 (ø28)

0.2756 (7)

0.3150 (8)

0.16 (4)

1.57 (40)

inch (mm)

MA

CD

JA

HA

HL

4-KA

Shaft end

f

e

d

b

ag (Key length)

f

e

d

b

AB

BC

(AB)

1.34(34)

2.09(53)EG

FA GA

DE L

2×2-NPT3/8

PT3/8

GT

Port A: ClockwisePort B: Counterclockwise


Port B: ClockwisePort A: Counterclockwise



(Exhaust port)


With Flange MountingTAM4-030FG

With Foot MountingTAM4-030LG

P

DGDG

GB

JB

4-KBCE

NF

AB

BD

(AC)

2.09(53)

HB

L

MB FBEL





Basic Circuit

For continuous run either clockwise or counter clockwise. Performance curve shown on the diagram is based on this circuit because of no back pressure.

Turns motor clockwise or counter-clockwise via solenoid valve. In this case speed is controlled by throttle but exhaust is also throttled. Air throttling consumes less air. In this circuit, however, when back pressure comes big owing to valve capacity and piping, there causes output drops. Upon selecting solenoid valve and piping, it is advisable to afford much possible room.

Attaching quick throttle valve to the aforegoing No. 2 circuit, specially designed so as not to cause back pressure, you can expect both output and rotational frequency as close as shown on the performance curve.

Attaching reducing speed circuit to the said No. 2 circuit, two directional solenoid valves open on high speed operations and also they close on slow speed operation, thus two different speeds are obtainable. Back pressure raises as same as No. 2 circuit and output drops than performance curve.

Specially designed to the aforegoing No. 4 circuit so as not to raise back pressure. You can expect to obtain output and rotational frequency almost same as performance curve.

Basic CircuitFor all reversible air motors, 4 way directional control valve (Taiyo USR Series 550-551) is recommended. In uncertain applications, consult Taiyo.

Port Size (NPT) Air Motor

Modular F.R.L. Combination Set 4 Way Directional Air Valve Solenoid/Pilot OperatedTRIO TWIN

1/4UTAM4-010 UCFRL-

(Port Size: 1/4-3/8)UCKL-

(Port Size: 1/4-3/8)USR550 Series

(Cv factor .8)UTAM4-15

3/8 UTAM4-030 UMFRL- (Port Size: 1/2-3/4)

UCKL- (Port Size: 1/2-3/4)

USR551 Series (Cv factor 1.1)

1. One Direction Rotation

Recommended Air Line Equipment

2. Reversible Rotation

3. Reversible Rotation with High Output

4. Reversible Rotation with Reducing Speed Circuit

5. Reversible Rotation with Reducing Speed Circuit and High Output

0810

15 20

15 20

0810

9




Offer of Sale

The items described in this document and other documents and descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized distributors (“Seller”) are hereby offered for sale at prices to be established by Seller. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order for any item described in its document, when communicated to Seller verbally, or in writing, shall constitute acceptance of this offer. All goods, services or work described will be referred to as “Products”.

1. Terms and Conditions. Seller’s willingness to offer Products, or accept an order for Products, to or from Buyer is subject to these Terms and Conditions or any newer version of the terms and conditions found on-line at www.parker.com/saleterms/. Seller objects to any contrary or additional terms or conditions of Buyer’s order or any other document issued by Buyer.2. Price Adjustments; Payments. Prices stated on Seller’s quote or other documen-tation offered by Seller are valid for 30 days, and do not include any sales, use, or other taxes unless specifically stated. Unless otherwise specified by Seller, all prices are F.C.A. Seller’s facility (INCOTERMS 2010). Payment is subject to credit approval and is due 30 days from the date of invoice or such other term as required by Seller’s Credit Department, after which Buyer shall pay interest on any unpaid invoices at the rate of 1.5% per month or the maximum allowable rate under applicable law.3. Delivery Dates; Title and Risk; Shipment. All delivery dates are approximate and Seller shall not be responsible for any damages resulting from any delay. Regardless of the manner of shipment, title to any products and risk of loss or damage shall pass to Buyer upon placement of the products with the shipment carrier at Seller’s facility. Unless otherwise stated, Seller may exercise its judgment in choosing the carrier and means of delivery. No deferment of shipment at Buyers’ request beyond the respec-tive dates indicated will be made except on terms that will indemnify, defend and hold Seller harmless against all loss and additional expense. Buyer shall be responsible for any additional shipping charges incurred by Seller due to Buyer’s acts or omissions.4. Warranty. Seller warrants that the Products sold hereunder shall be free from defects in material or workmanship for a period of eighteen months from the date of delivery to Buyer. The prices charged for Seller’s products are based upon the exclu-sive limited warranty stated above, and upon the following disclaimer: DISCLAIMER OF WARRANTY: THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO PRODUCTS PROVIDED HEREUNDER. SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS AND IMPLIED, INCLUDING DESIGN, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.5. Claims; Commencement of Actions. Buyer shall promptly inspect all Products upon delivery. No claims for shortages will be allowed unless reported to the Seller within 10 days of delivery. No other claims against Seller will be allowed unless asserted in writing within 30 days after delivery. Buyer shall notify Seller of any alleged breach of warranty within 30 days after the date the defect is or should have been discovered by Buyer. Any action based upon breach of this agreement or upon any other claim arising out of this sale (other than an action by Seller for an amount due on any invoice) must be commenced within 12 months from the date of the breach without regard to the date breach is discovered.6. LIMITATION OF LIABILITY. UPON NOTIFICATION, SELLER WILL, AT ITS OPTION, REPAIR OR REPLACE A DEFECTIVE PRODUCT, OR REFUND THE PURCHASE PRICE. IN NO EVENT SHALL SELLER BE LIABLE TO BUYER FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF, OR AS THE RESULT OF, THE SALE, DELIVERY, NON-DELIVERY, SERVICING, USE OR LOSS OF USE OF THE PRODUCTS OR ANY PART THEREOF, OR FOR ANY CHARGES OR EXPENSES OF ANY NATURE INCURRED WITHOUT SELLER’S WRITTEN CONSENT, EVEN IF SELLER HAS BEEN NEGLIGENT, WHETHER IN CONTRACT, TORT OR OTHER LEGAL THEORY. IN NO EVENT SHALL SELLER’S LIABILITY UNDER ANY CLAIM MADE BY BUYER EXCEED THE PURCHASE PRICE OF THE PRODUCTS.7. User Responsibility. The user, through its own analysis and testing, is solely responsible for making the final selection of the system and Product and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application and follow applicable industry standards and Product information. If Seller provides Product or system options, the user is responsible for determining that such data and specifica-tions are suitable and sufficient for all applications and reasonably foreseeable uses of the Products or systems.8. Loss to Buyer’s Property. Any designs, tools, patterns, materials, drawings, confi-dential information or equipment furnished by Buyer or any other items which become Buyer’s property, will be considered obsolete and may be destroyed by Seller after two consecutive years have elapsed without Buyer ordering the items manufactured using such property. Seller shall not be responsible for any loss or damage to such property while it is in Seller’s possession or control.9. Special Tooling. A tooling charge may be imposed for any special tooling, includ-ing without limitation, dies, fixtures, molds and patterns, acquired to manufacture Products. Such special tooling shall be and remain Seller’s property notwithstanding payment of any charges by Buyer. In no event will Buyer acquire any interest in appa-ratus belonging to Seller which is utilized in the manufacture of the Products, even if such apparatus has been specially converted or adapted for such manufacture and notwithstanding any charges paid by Buyer. Unless otherwise agreed, Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time.10. Buyer’s Obligation; Rights of Seller. To secure payment of all sums due or oth-erwise, Seller shall retain a security interest in the goods delivered and this agreement shall be deemed a Security Agreement under the Uniform Commercial Code. Buyer authorizes Seller as its attorney to execute and file on Buyer’s behalf all documents Seller deems necessary to perfect its security interest. 11. Improper use and Indemnity. Buyer shall indemnify, defend, and hold Seller harmless from any claim, liability, damages, lawsuits, and costs (including attorney fees), whether for personal injury, property damage, patent, trademark or copyright

infringement or any other claim, brought by or incurred by Buyer, Buyer’s employees, or any other person, arising out of: (a) improper selection, improper application or other misuse of Products purchased by Buyer from Seller; (b) any act or omission, negligent or otherwise, of Buyer; (c) Seller’s use of patterns, plans, drawings, or specifications furnished by Buyer to manufacture Product; or (d) Buyer’s failure to comply with these terms and conditions. Seller shall not indemnify Buyer under any circumstance except as otherwise provided.12. Cancellations and Changes. Orders shall not be subject to cancellation or change by Buyer for any reason, except with Seller’s written consent and upon terms that will indemnify, defend and hold Seller harmless against all direct, incidental and consequential loss or damage. Seller may change product features, specifications, designs and availability with notice to Buyer.13. Limitation on Assignment. Buyer may not assign its rights or obligations under this agreement without the prior written consent of Seller.14. Force Majeure. Seller does not assume the risk and shall not be liable for delay or failure to perform any of Seller’s obligations by reason of circumstances beyond the reasonable control of Seller (hereinafter “Events of Force Majeure”). Events of Force Majeure shall include without limitation: accidents, strikes or labor disputes, acts of any government or government agency, acts of nature, delays or failures in delivery from carriers or suppliers, shortages of materials, or any other cause beyond Seller’s reasonable control. 15. Waiver and Severability. Failure to enforce any provision of this agreement will not waive that provision nor will any such failure prejudice Seller’s right to enforce that provision in the future. Invalidation of any provision of this agreement by legislation or other rule of law shall not invalidate any other provision herein. The remaining provi-sions of this agreement will remain in full force and effect.16. Termination. Seller may terminate this agreement for any reason and at any time by giving Buyer thirty (30) days written notice of termination. Seller may immediately terminate this agreement, in writing, if Buyer: (a) commits a breach of any provision of this agreement (b) appointments a trustee, receiver or custodian for all or any part of Buyer’s property (c) files a petition for relief in bankruptcy on its own behalf, or by a third party (d) makes an assignment for the benefit of creditors, or (e) dissolves or liquidates all or a majority of its assets.17. Governing Law. This agreement and the sale and delivery of all Products here-under shall be deemed to have taken place in and shall be governed and construed in accordance with the laws of the State of Ohio, as applicable to contracts executed and wholly performed therein and without regard to conflicts of laws principles. Buyer irrevocably agrees and consents to the exclusive jurisdiction and venue of the courts of Cuyahoga County, Ohio with respect to any dispute, controversy or claim arising out of or relating to this agreement. 18. Indemnity for Infringement of Intellectual Property Rights. Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this Section. Seller will defend and indemnify Buyer against allegations of infringement of U.S. patents, U.S. trademarks, copyrights, trade dress and trade secrets (“Intellectual Property Rights”). Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an action brought against Buyer based on an allegation that a Product sold pursuant to this Agreement infringes the Intellectual Property Rights of a third party. Seller’s obliga-tion to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten (10) days after Buyer becomes aware of such allegations of infringement, and Seller having sole control over the defense of any allegations or actions including all negotia-tions for settlement or compromise. If a Product is subject to a claim that it infringes the Intellectual Property Rights of a third party, Seller may, at its sole expense and option, procure for Buyer the right to continue using the Product, replace or modify the Product so as to make it noninfringing, or offer to accept return of the Product and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the fore-going, Seller shall have no liability for claims of infringement based on information provided by Buyer, or directed to Products delivered hereunder for which the designs are specified in whole or part by Buyer, or infringements resulting from the modification, combination or use in a system of any Product sold hereunder. The foregoing provi-sions of this Section shall constitute Seller’s sole and exclusive liability and Buyer’s sole and exclusive remedy for infringement of Intellectual Property Rights.19. Entire Agreement. This agreement contains the entire agreement between the Buyer and Seller and constitutes the final, complete and exclusive expression of the terms of sale. All prior or contemporaneous written or oral agreements or negotiations with respect to the subject matter are herein merged.20. Compliance with Law, U. K. Bribery Act and U.S. Foreign Corrupt Practices Act. Buyer agrees to comply with all applicable laws and regulations, including both those of the United Kingdom and the United States of America, and of the country or countries of the Territory in which Buyer may operate, including without limitation the U. K. Bribery Act, the U.S. Foreign Corrupt Practices Act (“FCPA”) and the U.S. Anti-Kickback Act (the “Anti-Kickback Act”), and agrees to indemnify and hold harmless Seller from the consequences of any violation of such provisions by Buyer, its employ-ees or agents. Buyer acknowledges that they are familiar with the provisions of the U. K. Bribery Act, the FCPA and the Anti-Kickback Act, and certifies that Buyer will adhere to the requirements thereof. In particular, Buyer represents and agrees that Buyer shall not make any payment or give anything of value, directly or indirectly to any governmental official, any foreign political party or official thereof, any candidate for foreign political office, or any commercial entity or person, for the purpose of influ-encing such person to purchase products or otherwise benefit the business of Seller.

Offer of Sale




Notes

01/19 / Catalog HY08-T1914-B1/NA

Taiyo America1700 East Spring Street St. Marys, Ohio 45885 USA phone (419) 300-8811fax (419) 300-9765www.taiyoamericacylinders.com

air motor radial piston type - taiyo america · 2019. 1. 23. · air motor - radial piston type...

Documents