aii28617 rear camera attachment - honda · remove the rear bumper: • remove the license plate...

© 2005 American Honda Motor Co., Inc - All Rights Reserved. AII 28617 (0502) 1 of 17

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

FEB 2005

RIDGELINEREAR CAMERAATTACHMENT

(EX-L WITH NAVI)

AII 28617

08B21-SJC-1000-91

PART LIST

Attachment KitP/N: 08B21-SJC-100

Rear camera trim

Rear camera bracket

Rear camera subbracket

Harness clamp bracket A

Harness clamp bracket B

Rear camera subharness

Template

19 Wire ties

9 Small wire ties

6 Wire ties with clip

6-Pin connector

Grommet

2 Pieces of clear adhesive tape

3 Blind nuts

dcs

HandA-Accessories.com

2 of 17 AII 28617 (0502) © 2005 American Honda Motor Co., Inc - All Rights Reserved.

Rear Camera Kit P/N: 08A57-SJC-100

2 EPT sealers

4 Cushion tapes

2 Socket bolts, 4 x 10 mm

3 Washer screws, 4 x 12 mm

2 Washer screws, 4 x 6 mm

Rear camera

Owner’s Manual

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Flat-tip screwdriver

10 mm Combination wrench

Ratchet

10, 12 mm and 14 mm Socket

Torque wrench

File

Isopropyl alcohol

Shop towel

Tape measure

Drill

3 mm, 8 mm, and 10 mm Drill bits

Utility knife

T40, and T50 Torx bit

KTC trim tool

Scissors

Tape

Electrical tape

Wire

3 mm Hex wrench

Illustration of the Rear Camera Installed on theVehicle

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for theradio, then write down the radio station presets.

2. Disconnect the negative cable from the battery.

4712100K

CONTROL UNIT

REAR CAMERASUBHARNESS

6-PIN CONNECTOR

REARCAMERA

GROMMET

7 Clips

Round grommet

6 Oval grommets


3. Remove the fuel fill door release handle. Removethe left front door sill trim (three clips and threeretaining tabs).

4. Remove the left rear door sill trim (three clips andfour retaining tabs).

5. Pull away the weatherstrip from the B-pillar lowertrim panel. Remove the left seat belt lower anchorbolt cover and remove the lower anchor bolt.Remove the left B-pillar lower trim panel bypulling it out toward you as shown.

• Seat belt anchor bolt torque: 30 to 35 N·m(22 to 25 lbs)

3916041T

RETAININGTAB

RETAININGTAB

LEFT FRONTDOOR SILL TRIMCLIPS (3)

FRONT

FUEL FILL DOORRELEASE HANDLE

4212450T

RETAININGTAB

RETAININGTAB

LEFT REARDOOR SILL TRIM

CLIPS (3)

FRONT

4212330T

FRONT

LEFTB-PILLARLOWERTRIMPANEL

LEFT SEAT BELTLOWER ANCHOR BOLT

WEATHERSTRIP(Pull away.)

LOWER ANCHORBOLT COVER

6. Remove the driver’s seat frame rear cover (twoclips and two hooks).

4713010K

DRIVER’S SEAT

HOOKS (2)

DRIVER’S SEATFRAME REAR COVER

CLIPS (2)


9. Remove the rear seat belt anchor bolt and eightseat anchor bolts.


8. Remove the rear seat bracket covers:

• Remove the left and right rear seat bracketcovers (two clips for each cover).

• Remove the center seat bracket cover (twoclips and nine retaining tabs).

7. Lift up the rear seats, and remove the rear under-seat trim panel:

• Remove the right rear under-seat trim panel(four clips).

• Remove the left rear under-seat trim panel(seven clips).

4212460T

CLIPRIGHT REARSEAT BRACKETCOVER

CENTER SEATBRACKETCOVER

CLIPS (2)

RETAININGTABS (9)

LEFT REARSEAT BRACKETCOVER

CLIP

10. Remove the caps from the rear trim panel cover(four retaining tabs for each cover), and removethe rear seat.

4212371T

RETAININGTABS (4)

CAP

RETAININGTABS (4)

CAP

REAR SEAT

4212362T

SEATANCHORBOLTS (8) REAR SEAT

BELT ANCHORBOLT

4212341T

CLIPS (7)

CLIPS (4)

LEFT REARUNDER-SEAT TRIMCOVER

RIGHT REARUNDER-SEATTRIM PANEL

CLIPS


11. Remove the rear trim panel cover (eight clips andtwo retaining tabs).

14. Remove the left rear lower anchor bolt cover, andremove the left rear seat belt lower anchor bolt:


4715601K

CLIP

LEFT REARSEAT BELTANCHOR BOLTCOVER CLIP

RETAININGTABS (4)

LEFT REAR PILLARUPPER TRIM

LEFT REAR SEATBELT UPPERANCHOR BOLT

TABS (2)

4212381T

CLIPS (6)

REAR TRIMPANEL COVER

CLIP

RETAININGTABS (2)

12. Remove the left rear seat belt upper anchor boltcover (four retaining tabs), and remove the leftrear seat belt upper anchor bolt:


13. Remove the left rear pillar upper trim:

• With side airbag; pull the clip, and remove theleft rear pillar trim by releasing the one clip.

• Without side airbag; remove the left rear pillartrim by releasing the two clips.

15. Remove the upper clip, then pull the left rear pillarlower trim out toward you to release two clips.

16. Remove the left rear taillight (two bolts, two clipsand vehicle connector). Remove the right taillightthe same way.

3924012H

LEFT SIDE RIGHT SIDE

VEHICLECONNECTOR

VEHICLECONNECTOR

CLIPS (2)

BOLT

VEHICLECONNECTORLEFT

TAILLIGHT

4715611K

CLIP

CLIPS (2)

LEFT REARLOWERANCHORBOLT COVER

LEFT REARSEAT BELTLOWERANCHORBOLT

LEFT REARPILLARLOWER TRIM


17. Remove the rear bumper:

• Remove the license plate (two bolts).

• Remove two bolts, eight self-tapping screwsand six clips from the rear bumper.

• Pull the rear bumper toward you. Unplug thetwo vehicle connectors, and remove the rearbumper.

• Set the rear bumper on the blanket.

18. Remove the rear roof trim:

• Remove the roof trim nut covers (two retainingtabs for each cover).

• Remove the two nuts.

• Using a KTC trim tool, carefully pry up thefront of the trim to release the three front clips.Start with the left clip and work towards theright clip.

• Gently lift the front of the trim to release thefour rear clips.

• Remove the antenna grommet from the roof,unplug the vehicle connector, and remove therear roof trim.

BOLTS (2)

SELF-TAPPINGSCREWS (8)

CLIPS (6)

REARBUMPER

BOLTLICENSE PLATE

VEHICLECONNECTORS(2)

4D19051H

ROOF TRIMNUT COVER RETAINING

TABS (2)

NUTS (2)

REAR ROOF TRIM

4D19062H

LEFT CLIP(Start here.)

CENTER CLIP(Second.)

RIGHT CLIP(Finish here.)

CLIPS (7)

KTC TRIM TOOL

CLIPS (4)

4804024H

REARROOF TRIM

ANTENNAGROMMET

HOOKS (2)

VEHICLECONNECTORS (2)

HIGH-MOUNTBRAKE LIGHTGROMMET


19. Remove and discard the grommets from the roofpanel, and install the six oval grommets and oneround grommet into the roof panel.

20. On the rear roof trim backside, remove anddiscard the clips from the rear roof trim, andinstall the seven clips to the rear roof trim.

4D20510K

GROMMET(Discard.)

ROUNDGROMMET

ROOF PANEL

OVALGROMMETS (6)

GROMMETS (6)(Discard.)

4D20501K

REAR ROOF TRIM

CLIPS (7)

CLIPS (7)(Discard.)

22. Remove the left C-pillar outer trim light (onescrew) and unplug the connector.

21. Remove the left bed rail trim:

• Remove the screw cover (four retaining tabs).

• Remove the self-tapping screw.

• Pull the left bed rail trim back to release thesix clips, and remove the left bed rail trim.

3926071H

SCREWCOVER

RETAININGTABS (4)

LEFT BEDRAIL TRIM

CLIPS (6)

SELF-TAPPINGSCREW

LEFT BEDRAIL TRIM

CLIPS (3)(Remove.)

CLIPS (3)(Install.)

LEFT C-PILLAROUTER TRIM

C-PILLAROUTER TRIM

VEHICLE PANEL

VEHICLECONNECTOR

SELF-TAPPINGSCREW

23. Remove the left C-pillar outer trim (slide rearward,and unplug the vehicle connector). Remove theclips from the body, and reinstall the clips to theleft C-pillar outer trim.


3926021HT40 TORXBOLTS (6)

LEFT SIDEBED PANEL

26. Remove the left lower bed light (one self-tappingscrew, pull the light out towards you, and unplugthe vehicle connector).

3926062H

SELF-TAPPINGSCREW

LEFT LOWERBED LIGHT

CLIP

VEHICLECONNECTOR

T50 TORXBOLT

LEFT REARANCHOR

25. Remove the front bed panel (six torx bolts).28. Remove the left side bed panel (six torx bolts).

27. Remove the left rear anchor (two torx bolts).

24. Remove the left front anchor (two torx bolts).

4610041H

T50 TORXBOLT

LEFT FRONTANCHOR

3929032H

FRONT BEDPANEL

T40 TORXBOLTS (6)


29. Remove the tailgate trim:

• Remove the four screws and release the oneend clip on each side.

• Sharply push the tailgate trim to the right torelease the 16 clips from the trim.

• Remove the 16 clips from the tailgate, andreinstall the 16 clips to the tailgate trim in thedirection shown.

4605080T

SELF-TAPPINGSCREWS (4)

CLIPS (2)

TAILGATE TRIM

CLIPS (16)TAILGATETRIM

32. Center punch the tailgate at the marks on thetemplate. Remove the template.

31. Get the template. Using scissors, cut out themarked area from the template. Align the edge ofthe template with the edge of the tailgate asshown, and attach it to the tailgate with tape.

30. Remove the tailgate panel (seven torx screws).

4605090T

T40 TORXSCREWS (7)

TAILGATEPANEL

4707041K

OUTERTAILGATE

CUTTEMPLATE

TAPES (9)

TEMPLATE

CUTAREA

TAILGATEUPPERHANDLE

4708010KCENTERPUNCH

CUTTEMPLATE

TAILGATE

MARKS (4)

TAILGATEUPPERHANDLE


34. Install one blind nut into each 8 mm hole.

4708030K

TAILGATE

8 mmHOLES (3)BLIND NUT

35. Remove the four screws from the rear camera.Route the rear camera harness through the rearcamera subbracket, and install the rear camerasubbracket to the rear camera with the fourscrews.

36. Attach a piece of wire to the terminals on the rearcamera harness, and tape the wire to theterminals.

4708050K

REARCAMERA

REAR CAMERASUBBRACKET

REAR CAMERAHARNESS

SCREWS (4)

4913020K

TERMINALS

TAPE WIRE

REAR CAMERAHARNESS

33. Drill three 8 mm holes and one 10 mm hole in thetailgate.

• Wrap tape around a 3 mm drill bit, an 8 mmdrill bit and a 10 mm drill bit 10 mm from theend or use a drill stop.

• While wearing eye protection, drill a 3 mmhole, then an 8 mm hole in all four locations.Drill a 10 mm hole only in the upper centerhole.

• Remove any burrs, and apply touch-up paint toall of the holes.

4708021K

DRILL DRILL BIT(3 mm 8 mm)

DRILL BIT(3 mm 8 mm 10 mm)

TAILGATE

MARKS (4)

TAPE(Wrap tape aroundthe drill bit.)

DRILL BIT10 mm

UPPERCENTERHOLE(10 mm)


37. Route the rear camera harness through the 10 mmhole in the tailgate, and seat the grommet into the10 mm hole.

4708071K

REAR CAMERAHARNESS

10 mmHOLE

GROMMET

GROMMET

WIRE

VEHICLE PANEL

39. Align the two locating tabs on the rear camerasubbracket with the slots in the rear camerabracket, and install two 4 x 6 mm washer-screws.

NOTE: Make sure the flat surface of the rearcamera subbracket is facing up; otherwise, thecamera view will be upside down.

38. Install the rear camera bracket to the three blindnuts with three 4 x 12 mm washer-screws.

4708041K

BLINDNUT

4 x 12 mmWASHERSCREW

TAILGATE PANEL

REAR CAMERABRACKET

4708081K

4 x 6 mmWASHERSCREW

REAR CAMERASUBBRACKETFlat surfacefacing up.

REAR CAMERABRACKET

4 x 6 mmWASHERSCREW

SLOTS (2)

LOCATINGTABS (2)


41. Route the rear camera harness along the tailgateas shown.

4708092K

REAR

TAILGATE

REAR CAMERAHARNESS

42. Remove the torx bolt from the tailgate hinge, andattach the harness clamp bracket B to thetailgate using the torx bolt you just removed. Donot tighten the torx bolt at this time.

4709013K

T50 TORX BOLT(Do not tighten at this time.)

HARNESS CLAMPBRACKET B

TAILGATE

TAILGATEHINGE

40. Install clear adhesive tape to the tailgate:

• Open the tailgate.

• Get the pieces of clear adhesive tape. Usingscissors, cut 30 mm from the end of eachpiece.

• Using isopropyl alcohol on a shop towel, cleanthe tailgate where the adhesive tape willattach.

4N09043K

TAILGATE

REAR

30 mm

TAILGATELIP

TAILGATE

FIRSTADHESIVETAPE

CLEARADHESIVETAPE

CLEARADHESIVETAPE

30 mm SECONDADHESIVE TAPE


43. Secure the rear camera harness to the harnessclamp bracket with two small wire ties. Attach thewire tie, over the black tape attached to theharness, where the vinyl cover begins.

4709023K

REARCAMERAHARNESS

SMALLWIRE TIE(Attach over theblack tape.)

T50 TORX BOLT(Torque to 29 to 32 N·m)

HARNESSCLAMPBRACKET

BLACKTAPE

SMALLWIRE TIE

4709032K

TAILGATE

T50 TORX BOLT(Do not tightenat this time.)

HARNESS CLAMPBRACKET A

TAILGATEHINGE

46. Pull the rear camera harness out from the insideof the tailgate, and secure the rear cameraharness to the harness clamp bracket A with onesmall wire tie. Attach the wire tie over the blacktape attached to the harness.

4N09050K

CUSHION TAPE REAR CAMERAHARNESS

REARCUSHION TAPE(Cut in half.)

TAILGATE

4709044K

T50 TORXBOLT(Torque to29 to 32 N·m)

REARCAMERAHARNESS

SMALLWIRE TIE(Attach over theblack tape.)

HARNESSCLAMPBRACKET A

TAILGATE

BLACKTAPE

44. Torque the T50 torx bolt to 29 to 32 N·m (21 to23 lbs).

45. Close the tailgate. Remove the lower outboardhinge bolt, and attach harness clamp bracket A tothe tailgate hinge with the torx bolt you justremoved. Do not tighten the torx bolt at this time.

47. Torque the T50 torx bolt to 29 to 32 N·m (21 to23 lbs).

48. Open the tailgate. Using isopropyl alcohol on ashop towel, clean the tailgate where the cushiontapes will attach. Using scissors, cut one cushiontape in half. Secure the rear camera harness tothe tailgate with two half cushion tapes and twofull cushion tapes at the locations shown.


52. Route the rear camera harness out through thebed panel hole, and secure the rear cameraharness to the vehicle harness with one wire tiejust inside the panel hole.

4709050K

WIRETIE

VEHICLEHARNESS

FRONT

BED PANEL HOLE

REARCAMERAHARNESS

LEFT SIDEVEHICLEPANEL

53. Route the rear camera harness along the vehicleharness towards the front of the vehicle, andsecure it to the vehicle harness with six wire tiesin the areas shown.

4709062K

VEHICLEHARNESS

WIRE TIES (6)

REAR CAMERAHARNESS

4N09060K

REAR CAMERAHARNESS

LEFT SIDEVEHICLEPANEL HOLE

WIRE TIE VEHICLEHARNESS

49. Secure the rear camera harness to the tailgatewith five wire ties with clip.

4708103K

WIRE TIESWITH CLIP (5)

TAILGATE

REAR

TAILGATE

REAR CAMERAHARNESS

CUSHION TAPECut in half.

51. Route the rear camera harness through the leftside vehicle panel hole, and secure the rearcamera harness to the vehicle harness with twowire ties.

50. Using isopropyl alcohol on a shop towel, clean thetailgate where the cushion tape will attach. Usingscissors, cut one cushion tape in half. Secure therear camera harness to the tailgate with one halfcushion tape.


54. Remove the vehicle grommet from the left C-pillar.

4709071K

VEHICLEGROMMET

GROMMET

VEHICLEGROMMETOPENING

REARCAMERAHARNESS

BED BULKHEAD

REARCAMERAHARNESS

WIRE

LEFT C-PILLAR

4709080K

TAPE

GROMMET

REARCAMERAHARNESS

VEHICLEGROMMETOPENING

UP

DOWN

C-PILLAR

GROMMET

55. Insert the rear camera harness through thegrommet, and route the rear camera harnessthrough the vehicle grommet opening. Seat thegrommet into the grommet hole.

56. Using electrical tape, secure the grommet to therear camera harness. Pay attention to the angle ofthe grommet.

57. Inside the passenger’s compartments turn downthe rear panel insulator. Pull the rear cameraharness out from the hole in the C-pillar, andremove the tape and wire from the rear cameraharness.

4712012K

FRONT

VEHICLE PANELOPENING

REAR CAMERAHARNESS

TERMINALS (6)

TAPE

LOCK

6-PINCONNECTOR

Harness sideview

6-PINCONNECTOR

Red/Red

6-PINCONNECTOR

Black/Black Brown

Blue/Black

White/White

Yellow/Yellow

WIRE

4712031K

FRONT

VEHICLEHARNESS

VEHICLECONNECTOR

REAR CAMERAHARNESS6-PINCONNECTOR


WIRE TIE

REAR CAMERASUBHARNESS6-PINCONNECTOR

WIRE TIE

WIRETIES (2)

60. Route the rear camera subharness forward alongthe vehicle harness, and secure the subharnessto the vehicle harness with five wire ties.

58. Remove the lock from the 6-pin connector. Plugthe rear camera harness terminals into the 6-pinconnector as shown. Reinstall the lock.

59. Get the rear camera subharness. Plug the rearcamera subharness 6-pin connector into the rearcamera harness 6-pin connector, and secure theconnected 6-pin connectors to the vehicleconnectors with two wire ties.


64. Slide the driver’s seat back and forth to check thatthe rear camera subharness is not pulled too tightor is too loose.

4713040K

DRIVER’SSEATCheck that the rear

camera subharnessis not pulled tootight when the seatis moved back andforth.

63. Plug the rear camera subharness 6-pin connectorinto the Navi control unit.

4713030K

REAR CAMERASUB HARNESS6-PIN CONNECTOR

NAVICONTROLUNIT

62. Route the rear camera subharness along thevehicle harness and under the floor carpet, thenpull the rear camera subharness out from underthe floor carpet opening (under the driver’s seat).Secure the rear camera subharness to thevehicle harness with two wire ties.

4N10010K

DRIVER’SSEAT

VEHICLEHARNESS


FLOOR CARPETOPENING

WIRETIE

4712041K

FRONT

SMALLWIRE TIE

VEHICLEHARNESS


DRIVER’SSEAT

61. Continue routing the rear camera subharnessforward along the vehicle harness, and securethe subharness to the vehicle harness with foursmall wire ties.


65. Reconnect the negative cable to the battery. Turnthe key to the ON position, and enter the Navicode.

66. Move the shift knob to the “R” position.

67. Adjust the angle of the rear camera while watchingthe navigation monitor. When you are satisfied withthe camera angle, install the rear camera trim tothe rear camera bracket with two 4 x 10 mmsocket bolts.

68. Turn the key to the off position.

69. Measure and mark the rear bumper at the locationshown.

4N15011K

REARBUMPER

Cut off.

10 mm

15 mm

3 mm

72. Check that all wire harnesses are routed properlyand all connectors are plugged in.

73. Enter the customer’s radio anti-theft code, andreset the radio station presets.

74. Set the clock.

75. Check the operation of the rear camera accordingto the owner’s manual provided.

76. Put the rear camera Owner’s Manual in the glovebox with the vehicle owner’s manual.

77. Reinstall all removed parts.

70. Using a utility knife, cut and remove the measuredpiece from the rear bumper. Remove any burrsfrom the cut area with a file.

71. Reinstall the rear bumper.

4712090K4 x 10 mmSOCKET BOLT

REAR CAMERATRIM

REARCAMERA

Adjust the angle.

REAR CAMERABRACKET

aii28617 rear camera attachment - honda · remove the rear bumper: • remove the license plate...

Documents