aee po o 177542 af kaldewei puro duo …...australian standard 2023/1995 section 1.5 specifies, “a...
TRANSCRIPT
Kaldewei Puro Duo 1700x750x420 with Exafill
Page 1 of 8
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
page 2 of 11
Installation Instructions
Kaldewei Puro Duo 1700x750x420 with ExaFillAUSTRALIAN BATH & SHOWER FLOOR INSTALLATION Australian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be itted during the inal installation and that the bath be covered until all the building work has been completed.
This clip on material should be cut to the required lengths, mitered at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD OR MASONRY
WALL
PVC TILE TRIM
TILES
SUPPORT BATTEN
REFERENCESAustralian Standards AS. 3470-2010Fig 3.2 Typical Bath JunctionsSection 3. Installations 3.6 Pre Formed Shower Bases
3.7 Baths with showers over them 3.8 Baths and Spas
This bath has been supplied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
Kaldewei Puro Duo 1700x750x420 with Exafill
Page 2 of 8
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
page 3 of 11
Page 5 of 1
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only.Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Published 12/06/18
Specification Sheet
Dimensions are nominal measurements only.
To see the complete Kaldewei range go to www.reece.com.au/bathrooms
Kaldewei Puro Duo 1700x750x420 with ExaFill
SPECIFICATIONS
Recommended Use Domestic, Hotel & Commercial
Material 3.5 Enamel Steel
Colour White
Weight 48 kg
Options Available Grip Handle Including Drill ChargeBath Surround
Plug and Waste 40mm Pop-up Waste, Overflow included
Capacity 122 Litres
Fixing Hob Mounted, Built in, Undermount or Flush Mounted.Sound-deadening pads are a standard inclusion
Installation Option Leg System #2006759 available for easy installation
WARRANTY
Warranty - Domestic Use 30 Years
Spare Parts & LabourExafill
12 Months 15 Years
Please refer to Warranty Page for full Terms and Conditions
HANSGROHE EXAFILL INSTALLATION INSTRUCTIONS
DE Montageanleitung 2EN Assemblyinstructions 3
Exa-Bathtub Filler58112000
Push-Open50107000
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with ExaFillAUSTRALIAN BATH & SHOWER FLOOR INSTALLATIONAustralian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be itted during the inal installation and that the bath be covered until all the building work has been completed.
This clip on material should be cut to the required lengths, mitered at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD ORMASONRY
WALL
PVC TILE TRIM
TILES
SUPPORTBATTEN
REFERENCESAustralian Standards AS. 3470-2010Fig 3.2 Typical Bath JunctionsSection 3. Installations 3.6 Pre Formed Shower Bases
3.7 Baths with showers over them 3.8 Baths and Spas
This bath has been usppl;ied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
Kaldewei Puro Duo 1700x750x420 with Exafill
Page 3 of 8
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
page 4 of 11
Page 5 of 1
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only.Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Published 12/06/18
Specification Sheet
Dimensions are nominal measurements only.
To see the complete Kaldewei range go to www.reece.com.au/bathrooms
Kaldewei Puro Duo 1700x750x420 with ExaFill
SPECIFICATIONS
Recommended Use Domestic, Hotel & Commercial
Material 3.5 Enamel Steel
Colour White
Weight 48 kg
Options Available Grip Handle Including Drill ChargeBath Surround
Plug and Waste 40mm Pop-up Waste, Overflow included
Capacity 122 Litres
Fixing Hob Mounted, Built in, Undermount or Flush Mounted.Sound-deadening pads are a standard inclusion
Installation Option Leg System #2006759 available for easy installation
WARRANTY
Warranty - Domestic Use 30 Years
Spare Parts & LabourExafill
12 Months 15 Years
Please refer to Warranty Page for full Terms and Conditions
HANSGROHE EXAFILL INSTALLATION INSTRUCTIONS
3
Installation to DIN 1988
Whileinstallationofthebathmixerismadewatchthattheairgapfitting(DB)ismin.150mmabovetheupperedgeofthebathtub.
Installation to EN 1717
WhenassemblingtheiBoxuniversalwithintegratedsafetycombination(HD)payattentionthatthemiddleofthemixerismin.280mmabovetheupperedgeofthebathtub.
Centerbathtub
IMPORTANT! There must be an access door for maintenance.
There is no guarantee of Hansgrohe for compo-nents and their connections produced by third parties.
Aftercompletionthewholeinstallationmustbeflushed.
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with ExaFillAUSTRALIAN BATH & SHOWER FLOOR INSTALLATIONAustralian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be itted during the inal installation and that the bath be covered until all the building work has been completed.
This clip on material should be cut to the required lengths, mitered at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD ORMASONRY
WALL
PVC TILE TRIM
TILES
SUPPORTBATTEN
REFERENCESAustralian Standards AS. 3470-2010Fig 3.2 Typical Bath JunctionsSection 3. Installations 3.6 Pre Formed Shower Bases
3.7 Baths with showers over them 3.8 Baths and Spas
This bath has been usppl;ied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with ExaFillAUSTRALIAN BATH & SHOWER FLOOR INSTALLATIONAustralian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be itted during the inal installation and that the bath be covered until all the building work has been completed.
This clip on material should be cut to the required lengths, mitered at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD ORMASONRY
WALL
PVC TILE TRIM
TILES
SUPPORTBATTEN
REFERENCESAustralian Standards AS. 3470-2010Fig 3.2 Typical Bath JunctionsSection 3. Installations 3.6 Pre Formed Shower Bases
3.7 Baths with showers over them 3.8 Baths and Spas
This bath has been usppl;ied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
Kaldewei Puro Duo 1700x750x420 with Exafill
Page 4 of 8
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
page 5 of 11
�
(1MPa=10bar=147PSI)
Exa-Bathtub Filler58112000
Push-Open50107000
2
1 with flow limiter
without flow limiter
Page 5 of 1
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only.Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Published 12/06/18
Specification Sheet
Dimensions are nominal measurements only.
To see the complete Kaldewei range go to www.reece.com.au/bathrooms
Kaldewei Puro Duo 1700x750x420 with ExaFill
SPECIFICATIONS
Recommended Use Domestic, Hotel & Commercial
Material 3.5 Enamel Steel
Colour White
Weight 48 kg
Options Available Grip Handle Including Drill ChargeBath Surround
Plug and Waste 40mm Pop-up Waste, Overflow included
Capacity 122 Litres
Fixing Hob Mounted, Built in, Undermount or Flush Mounted.Sound-deadening pads are a standard inclusion
Installation Option Leg System #2006759 available for easy installation
WARRANTY
Warranty - Domestic Use 30 Years
Spare Parts & LabourExafill
12 Months 15 Years
Please refer to Warranty Page for full Terms and Conditions
HANSGROHE EXAFILL INSTALLATION INSTRUCTIONS
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with ExaFillAUSTRALIAN BATH & SHOWER FLOOR INSTALLATIONAustralian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be itted during the inal installation and that the bath be covered until all the building work has been completed.
This clip on material should be cut to the required lengths, mitered at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD ORMASONRY
WALL
PVC TILE TRIM
TILES
SUPPORTBATTEN
REFERENCESAustralian Standards AS. 3470-2010Fig 3.2 Typical Bath JunctionsSection 3. Installations 3.6 Pre Formed Shower Bases
3.7 Baths with showers over them 3.8 Baths and Spas
This bath has been usppl;ied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
Kaldewei Puro Duo 1700x750x420 with Exafill
Page 5 of 8
page 6 of 11
Page 5 of 1
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only.Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Published 12/06/18
Specification Sheet
Dimensions are nominal measurements only.
To see the complete Kaldewei range go to www.reece.com.au/bathrooms
Kaldewei Puro Duo 1700x750x420 with ExaFill
SPECIFICATIONS
Recommended Use Domestic, Hotel & Commercial
Material 3.5 Enamel Steel
Colour White
Weight 48 kg
Options Available Grip Handle Including Drill ChargeBath Surround
Plug and Waste 40mm Pop-up Waste, Overflow included
Capacity 122 Litres
Fixing Hob Mounted, Built in, Undermount or Flush Mounted.Sound-deadening pads are a standard inclusion
Installation Option Leg System #2006759 available for easy installation
WARRANTY
Warranty - Domestic Use 30 Years
Spare Parts & LabourExafill
12 Months 15 Years
Please refer to Warranty Page for full Terms and Conditions
HANSGROHE EXAFILL INSTALLATION INSTRUCTIONS
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with ExaFillAUSTRALIAN BATH & SHOWER FLOOR INSTALLATIONAustralian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be itted during the inal installation and that the bath be covered until all the building work has been completed.
This clip on material should be cut to the required lengths, mitered at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD ORMASONRY
WALL
PVC TILE TRIM
TILES
SUPPORTBATTEN
REFERENCESAustralian Standards AS. 3470-2010Fig 3.2 Typical Bath JunctionsSection 3. Installations 3.6 Pre Formed Shower Bases
3.7 Baths with showers over them 3.8 Baths and Spas
This bath has been usppl;ied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
5
SW 2 mm
2.
1.
1
�
2
3
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with Exafill
Page 6 of 8
page 7 of 11
Page 5 of 1
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only.Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Published 12/06/18
Specification Sheet
Dimensions are nominal measurements only.
To see the complete Kaldewei range go to www.reece.com.au/bathrooms
Kaldewei Puro Duo 1700x750x420 with ExaFill
SPECIFICATIONS
Recommended Use Domestic, Hotel & Commercial
Material 3.5 Enamel Steel
Colour White
Weight 48 kg
Options Available Grip Handle Including Drill ChargeBath Surround
Plug and Waste 40mm Pop-up Waste, Overflow included
Capacity 122 Litres
Fixing Hob Mounted, Built in, Undermount or Flush Mounted.Sound-deadening pads are a standard inclusion
Installation Option Leg System #2006759 available for easy installation
WARRANTY
Warranty - Domestic Use 30 Years
Spare Parts & LabourExafill
12 Months 15 Years
Please refer to Warranty Page for full Terms and Conditions
HANSGROHE EXAFILL INSTALLATION INSTRUCTIONS
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with ExaFillAUSTRALIAN BATH & SHOWER FLOOR INSTALLATIONAustralian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be itted during the inal installation and that the bath be covered until all the building work has been completed.
This clip on material should be cut to the required lengths, mitered at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD ORMASONRY
WALL
PVC TILE TRIM
TILES
SUPPORTBATTEN
REFERENCESAustralian Standards AS. 3470-2010Fig 3.2 Typical Bath JunctionsSection 3. Installations 3.6 Pre Formed Shower Bases
3.7 Baths with showers over them 3.8 Baths and Spas
This bath has been usppl;ied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
�
5
DE DasAblaufventildarfnurinWannenmitÜberlaufeingesetztwerden.
EN Thedrainvalvemayonlybeinstalledintubswithanoverflowopening.
DE Optional erhältlich: Hansgrohe Wannensifon #56373000.
EN Ordered seperately: Hansgrohe bath trap #56373000..
�
DE ACHTUNG! Der Verbindungsschlauch (nicht im Lieferumfang enthalten) dart nicht abkni-cken. Es müssen die Angaben des Schlauch-herstellers beachtet werden.
Hansgrohe übernimmt keine Gewährleistung für Fremdbauteile und deren Verbindungsstel-len.
EN IMPORTANT! Don‘t bend the connection hose (not part of delivery). You must follow the manufacturer instructions.
There is no guarantee of Hansgrohe for components and their connections produced by third parties.
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with Exafill
Page 7 of 8
page 8 of 11
Page 5 of 1
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only.Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Published 12/06/18
Specification Sheet
Dimensions are nominal measurements only.
To see the complete Kaldewei range go to www.reece.com.au/bathrooms
Kaldewei Puro Duo 1700x750x420 with ExaFill
SPECIFICATIONS
Recommended Use Domestic, Hotel & Commercial
Material 3.5 Enamel Steel
Colour White
Weight 48 kg
Options Available Grip Handle Including Drill ChargeBath Surround
Plug and Waste 40mm Pop-up Waste, Overflow included
Capacity 122 Litres
Fixing Hob Mounted, Built in, Undermount or Flush Mounted.Sound-deadening pads are a standard inclusion
Installation Option Leg System #2006759 available for easy installation
WARRANTY
Warranty - Domestic Use 30 Years
Spare Parts & LabourExafill
12 Months 15 Years
Please refer to Warranty Page for full Terms and Conditions
HANSGROHE EXAFILL INSTALLATION INSTRUCTIONS
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with ExaFillAUSTRALIAN BATH & SHOWER FLOOR INSTALLATIONAustralian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be itted during the inal installation and that the bath be covered until all the building work has been completed.
This clip on material should be cut to the required lengths, mitered at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD ORMASONRY
WALL
PVC TILE TRIM
TILES
SUPPORTBATTEN
REFERENCESAustralian Standards AS. 3470-2010Fig 3.2 Typical Bath JunctionsSection 3. Installations 3.6 Pre Formed Shower Bases
3.7 Baths with showers over them 3.8 Baths and Spas
This bath has been usppl;ied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
7
Reinigung / Cleaning
Bedienung / Operation
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with Exafill
Page 8 of 8
page 9 of 11
Page 5 of 1
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only.Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.
Published 12/06/18
Specification Sheet
Dimensions are nominal measurements only.
To see the complete Kaldewei range go to www.reece.com.au/bathrooms
Kaldewei Puro Duo 1700x750x420 with ExaFill
SPECIFICATIONS
Recommended Use Domestic, Hotel & Commercial
Material 3.5 Enamel Steel
Colour White
Weight 48 kg
Options Available Grip Handle Including Drill ChargeBath Surround
Plug and Waste 40mm Pop-up Waste, Overflow included
Capacity 122 Litres
Fixing Hob Mounted, Built in, Undermount or Flush Mounted.Sound-deadening pads are a standard inclusion
Installation Option Leg System #2006759 available for easy installation
WARRANTY
Warranty - Domestic Use 30 Years
Spare Parts & LabourExafill
12 Months 15 Years
Please refer to Warranty Page for full Terms and Conditions
HANSGROHE EXAFILL INSTALLATION INSTRUCTIONS
Installation Instructions
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference
Kaldewei Puro Duo 1700x750x420 with ExaFillAUSTRALIAN BATH & SHOWER FLOOR INSTALLATIONAustralian Standard 2023/1995 Section 1.5 specifies, “A built-in bath shall be provided with a tiling flange or bead not less than 10mm in height”.
When handling steel enamel baths, care must be taken that they are treated correctly. This applies to their transport, unpacking and installation.
Kaldewei recommends that baths be itted during the inal installation and that the bath be covered until all the building work has been completed.
This clip on material should be cut to the required lengths, mitered at the corners, and the area where the flashing material and the rim of the bath meet, should be filled with a mould-resistant Sanitary Grade sealant.
When the bath is installed, the minimum distance from the outside edge of the flange to the finished edge of the tiles shall be 10mm. The exposed area of the flange shall have continuous fall to the inside of the bath.
BATH OR SHOWER TRAY
FLEXIBLE MASTIC SEALANTTILE ADHESIVE
STUD ORMASONRY
WALL
PVC TILE TRIM
TILES
SUPPORTBATTEN
REFERENCESAustralian Standards AS. 3470-2010Fig 3.2 Typical Bath JunctionsSection 3. Installations 3.6 Pre Formed Shower Bases
3.7 Baths with showers over them 3.8 Baths and Spas
This bath has been usppl;ied with sufficient high impact rigid PVC modified grade material to allow, where necessary, for the bath to be flashed along the full length and ends to conform with the Australian standard.
8
97580000
96655000
96331000
97579000
(65x2)
97573000
9757600097575000
96093000
58085000
95487000
95426000
95427000
95742000
Plumbers, please ensure a copy of the InstallationInstructions are left with the end user for future reference