Sealing Solutions High Performance

1095 Evergreen Circle, Suite 200 The Woodlands, Texas 77380

800 644-9770 or 713-389-5049 info@Advanced-EMC.com

Low Friction Chemical Compatibility Vacuum to High Pressure Extreme Temperatures Engineered for High Performance

Rotary Reciprocating Static APPLICATIONS

Introducing the widest selection of high performance spring-energized seals available today... Advanced EMC Technologies specializes in the design and manufacture of spring-energized seals made from a wide range of high-performance polymers. Advanced EMC Technologies seals offer very low friction, wide temperature range, full chemical compatibility, and long service life. Advanced EMC Technologies seals routinely handle applications where conventional seals fail.

Spring Materials. Advanced EMC Technologies seals is are energized by one of three different spring style made from 300-series stainless steel. For unusually corrosive service we make the spring from Hastelloy.

Designs. There are three styles of seals, based on which of three different types of spring is used in the seal. This design has a cantilever beam spring, and is used for general purpose applications. The maximum pressure rating for rod and piston seal designs ranges from 3,000 to 30,000 psi. Cryogenic designs are rated to -320 F .

Design Concept. PTFE and other polymer blends make excellent sealing materials, especially when their resilience is enhanced by incorporating a spring energizer into a U-shaped groove in the seal itself. The spring provides permanent elasticity and immunity from compression set. The shape of the seal makes it pressure-actuated, becoming tighter as media pressure rises. By combining our high performance Fluorolon PTFE blends with corrosion resistant metal springs, Advanced EMC Technologies seals eliminate the disadvantages associated with conventional elastomeric seals - degradation, heat aging, embrittlement, chemical attack, swelling, compression set, and high friction. Seal materials. Advanced EMC Technologies seals are made from PTFE blends and other high performance polymers .

Hardware recommendations

Surface finish. Improving the finish on static and dynamic mating surfaces is a primary method for obtaining longer seal life, lower friction, and greater sealing integrity, in general we recommend finishes as shown below:

Mating Surface Hardness. Harder surfaces extend seal and hardware life by preventing abrasion to the metal and holding a smooth finish. In moderate speed and pressure conditions, the minimum recommended hardness is 44 RC. Higher speed/pressure or poor lubrication may require values from 65 to 72 RC, using special coatings Hardenable materials include: Shaft Coatings. In high-spees rotary or severe-service reciprocating, use chromium oxide or similar coatings with high hardness and smooth finish. Avoid chrome plating or use in light duty service only. Consult factory for further data on coatings and recommended substrates for your specific application.

contact us @ 1-800-644-9770 info@advanced-emc.com

SEAL DESIGN

SEALTYPE& REF.

PRESS.RATING

(psi)

TEMP.RANGE

F

VACUUM orLOW

PRESS.SEALINGABILITY

APPLICATIONS & SERVICE DATA

STATIC SERVICETemperature

LevelSealing Ability In Maximum

Pressure

Lignt Gases

Solvent Oil

RECIPROCATING SERVICETemperature

LevelMaximum Pressure (psi) Friction

Rating

at 30sfpm

at 100 sfpm

at 250 sfpm

ROTARY SERVICETemperature

LevelMaximum Pressure (psi) Friction

Rating

at 50sfpm

at 100 sfpm

1000 sftpm

2500 sfpm

5000sfpm

Standard Lip 3000 -320 to 575 E Gneral purpose static, reciprocating and slow rotary service as rod, piston or shaft seal.

Applications include hydraulic and pneumatic cylin-ders, actuators, connects, valve components.

-320 F F NA NA 5000

Ambient G G E 3000

550 F E E E 1500

-320 F F NA NA 5000

Ambient G G E 3000

450 F G E E 1500

-200 F G NA NA 5000

Ambient G G E 3000

550 F G G G 1500

-320 F F NA NA 15000

Ambient G G E 10000

550 F E E E 5000

-320 F F NA NA 30000

Ambient G E E 20000

550 F E E E 15000

-320 F G NA NA 5000

Ambient G G E 3000

550 F E E E 1500

-65 F F NA NA 3000

Ambient G E E 2000

400 F G E E 1000

-200 F F NA NA 5000

Ambient G G E 3000

500 F G E E 1500

-200 F P NA NA 350

Ambient F E G 250

500 F F E G 100

-200 F P NA NA 250

Ambient F G G 150

500 F F G G 50

-200 F F NA NA 750

Ambient G G G 500

500 F G G G 250

Ambient 3000 2000 1500 G

250 F 2500 1500 1000 G

550 F 1500 750 500 G

Ambient 3500 2000 1500 E

250 F 2500 1500 1000 E

450 F 2000 1000 750 E

Ambient 3000 NR NR P

250 F 1500 NR NR P

550 F 500 NR NR P

Ambient 10000 5000 2500 G

250 F 8000 4000 1500 G

550 F 5000 2000 1000 G

Ambient 20000 15000 10000 G

250 F 17500 10000 7500 G

550 F 8000 6000 4000 G

Ambient NA NA NA G

250 F NA NA NA G

550 F NA NA NA G

Ambient 200 1500 750 G

250 F 1500 1000 500 G

400 F 750 500 250 G

Ambient 3000 2000 1500 E

250 F 2500 1500 1000 E

450 F 2000 1000 750 E

Ambient NA NA NA NA

250 F NA NA NA NA

500 F NA NA NA NA

Ambient NA NA NA NA

250 F NA NA NA NA

500 F NA NA NA NA

Ambient NA NA NA NA

250 F NA NA NA NA

500 F NA NA NA NA

Ambient 2000 750 75 10 NR G

250 F 1000 500 50 NR NR G

550 F 250 100 NR NR NR G

Ambient 2000 750 75 10 NR E

250 F 1000 500 50 NR NR E

450 F 500 250 NR NR NR E

Ambient NR NR NR NR NR P

250 F NR NR NR NR NR P

550 F NR NR NR NR NR P

Ambient 3000 1500 150 50 NR G

250 F 2000 1000 100 NR NR G

550 F 500 250 NR NR NR G

Ambient 4500 2000 500 100 NR G

250 F 2500 1500 150 NR NR G

550 F 3000 500 NR NR NR G

Ambient 1500 500 NR NR NR G

250 F 750 250 NR NR NR G

550 F 100 NR NR NR NR G

Ambient 1500 750 100 50 NR G

250 F 750 500 50 10 NR G

400 F 500 100 10 NR NR G

Ambient 200 1000 500 50 NR E

250 F 1000 500 200 10 NR E

450 F 500 250 100 NR NR E

Ambient 250 150 50 25 10 E

250 F 150 100 25 10 5 E

500 F 100 50 10 5 2 E

Ambient 150 100 50 25 10 E

250 F 150 100 25 10 5 E

500 F 100 50 10 5 2 E

Ambient 500 200 100 50 25 G

250 F 200 150 50 75 10 G

500 F 150 100 10 10 5 G

AV1A

Standard Lip 3000 -320 to 450 G Our slant spring design is similar to AV1A but pro-vides closer control of friction or torque, greater toler-

ances and eccentricities. Also for small diameters seals and cross sections.BS1A

Radial Lip 3000 -200 to 575 E For slow dynamic and static applications only. Excellent in light gases, cryogenic, vacuum and tight

sealing available in Slant Spring designs.

AV4A

Standard Lip Extended heel

10000 -320 to 575 E Designed for greater extrusion resistance in applica-tions with high pressure up to 10,000 psi and high

temperature. Applications include pressure accumu-lators, cylinders and valve components. Also avail-

able in Slant Spring designs.AV4A

Standard LipExtreme Pressure

20000 -320 to 575 E For very high pressure cylinders or vessels requir-ing the use of an anti extrusion ring to support the

seal. Back up rings are available in high performance polymers (PEEK).AV5A

Internal &ExternalFace Seals

3000 -320 to 575 E Designed for slow rotary, static or oscillating service which requires sealing beetween two mating surfac-es; chemical tanks, vessels, swivel joints. Available in

V or slant spring designs.FV6A

FluorolipRotary Shaft Seal

2000 -65 to 400 G Shaft seal for use in pumps, motors and rotary equip-ment where a metal cased shaft seal cannot be used. The seals outer O-ring reduces or eliminates rotation

of the seal on the shaft.RS7A

Standard Flanged Seal

3000 -200 to 450 G General purpose rotary applications where the seal outer diameter is clamped axially in the seal housing

preventing rotation on the seal on the shaft.

FB2A

FluorolipSingle Lip

250 -200 to 500 G Designed for moderate to high speed applications. Recommended for combinations of speed, pressure, chemical resistance, high or low temperature and no

lubrication.SL

FluorolipDouble Lip

150 -200 to 500 G Same as SL design but with secondary lip for use as excluder for dust, water or particulates which could

migrate to sensitive areas. Also used to separate two distinct media.DLO

FluorolipDouble Lip

500 -200 to 500 E For use in higher pressure rotary service requiring additional sealing lip support. Applications include

compressors, pumps, hydrostatic clutches and transmissions.DL2S

RO

TAR

Y S

HA

FT S

EA

LSFA

CE

SE

ALS

RO

D/P

ISTO

N S

EA

LS

Spring Design Features

Advanced is the only supplier that designs and manufactures using all three of commonly speci-fied spring types for pressure-actuated PTFE seals. We select the best spring for your applica-tion from this complete range of options. Spring load is often customized to suit exact friction or torque requirements.

Typical Spring Curves

Each spring has unique load and deflection prop-erties affect seal performance. Spring load affects friction, wear rate, and ability to seal fluids tightly. Deflection range affects seals ability to handle gland tolerances and take up seal wear.

M Cantilever Beam Spring

Moderate load and deflection range. This is an all purpose spring that is well suited for positive wip-ing action at the front edge of seal lip.Available in standard and heavy load.

W Slantcoil SpringWide deflection range with relatively constant load over the life of the seal. Available in light, medium and heavy loads. Excellent for applications requir-ing close control of friction/torque.

H Helical SpringLow deflection range with very high unit load. Used for static or slow-dynamic service where friction and wear are not a problem.

Material Description Service Temperature

Range(F)

Coefficient of Friction

Corrosion Resistance

Radiation Resistance

(Rads)

FDAApproved for Food Contact

Lubricity in Water

Light Gas Low Pres-

sure Sealing

High Pressure Extrusion

Resistance

Abrasion to Soft Shafts

Wear Resistanceat High Speeds

Rotary Recip.

Fluorolon 1000

Premium-grade virgin PTFE . For static, slow dynamic or light-duty applications. Also for food contact service requing FDA Approval.

Color:white

-125 to 450 .05 to .08 E 7 x 104 Yes F G to E F Low F F

Fluorolon 1700

Premium-grade modified PTFE. Light duty material with greater wear resistance than 1000.

Reciprocating and slow rotary applications. Color:white

-320 to 475 .05 to .08 E 7 x 104 no F G to E FLow to

morderateF F to G

Fluorolon 1034

Modified Carbon/Graphite PTFE fillers provides better wear resistance in slow to moderate

reciprocating and rotary service.Color:black

-320 to 475 .05 to .10 E 7 x 104 no F G to E F to G Low F F to G

Fluorolon 1055

Graphite-reinforced. Good wear resistance in fast-rotary applications. Less abrasive to soft

shaft on in poorly-lubricated service. Color:black

- 250 to 350 .06 to .10 E 7 x 104 no F G G Low G to E G to E

Fluorolon 1091

Graphite-reinforced blend with better extrusion resistance at higher temperatures. Excellent in reciprocating applications on hard shafts.

Color:black

- 200 to 375 .06 to .12 E 7 x 104 no F F to G G to E Moderate G to E G to E

Fluorolon 1050

PTFE Glass and MoS2 severe dry and liquid service. Excellent wear and extrusion resistance

in liquids inert gases and vacuum. Color black

-250 to 550 .06 to .12 E 7 x 104 no p F to G G to EModerate to

highE E

Fluorolon 1051

Glass and MoS2 reinfocement for extreme con-ditions such as high pressure and temperature and for longer wear life on hardened dynamic

surfaces. Color: black

-200 to 575 .08 to .12 E 7 x 104 no p F E High E E

Fluorolon 1096

Proprietary polymer filled PTFE for use in dry service. Excellent wear resistance in vacuum,

inert gases. Low abrasion to shaft.Color:tan

-200 to 350 .08 to .12 C to E 7 x 104 no F F EModerate to

highE E

Fluorolon PCTFE

Premium-grade PCTFE. High-performance fluo-roplastic for extreme cryogenic service. Excel-

lent radiation resistance with excellent chemical compatibility.

Color: translucent white

-425 to 350 .30 to .40 E 1.8 x 107 no E E G to ELow to mod-

erateF to G G

Fluorolon 5000

Virgin UHMW Polyethylene. Excellent wear and abrasion resistance at moderate reciprocating speeds, high pressure or slow rotart service.

Very good lubricity in water-based media. Color: translucent white.

320 to 250 .15 to .25 G to E 7 x 107 yes E F to G ELow to mod-

erateF E

0

5

10

15

20

20 40 60

25

30

35

SLANTCOIL

CANTILEVER

HELICAL

All values contained in the above tables are based on Advanced EMC Technologies compounds at ambient temperatures and static conditions unless otherwise stated. All values may vary depending upon the material selection. E=Excellent G=Good F=Fair P=Poor NR=Not Recommended

Innovation in new materials development,

seal and bearing geometries, and manufacturing

processes are at work providing our customers

improved solutions to engineering problems.

Consistent, Accurate, on Time, and on Budget . . .

Advanced-EMC.com

twitter.com/Advanced_EMC

youtube.com/PTFESeals

facebook.com/AdvancedEMC

linkedin.com/company/advanced-emc-technologies

google.com/+Advanced-emc

1095 Evergreen Circle, Suite 200

The Woodlands, Texas 77380

800 644-9770 or 713-389-5049

info@Advanced-EMC.com